Driver Toshiba Hi speed Port Replicator III

Similar Questions

• Toshiba high speed Port Replicator III - use of 2 x 4 k monitors on 60 Hz

  Dear Toshiba support.

  Is it possible to run 2 x 4 monitors k on 60 Hz on the Port Replicator Port Hi-speed Toshiba III (dockingsation)?
  He says he has Display port 1.3 (supports 4 k monitor the 60 Hz.) and a 2.0 HDMI (which also supports monitor k 4 on 60 Hz.).

  With sincere friendships.
  Augurkie

  PauPau wrote in this thread on the high speed Port Replicator III
  https://Forum.Toshiba.EU/showthread.php?83052

  DisplayPort supports the following resolutions:

  Resolution - Refresh Rate (HZ)
  640 x 480 - 60,72,75,85
  720 x 480-85
  800 x 600 - 56,60,72,75,85
  848 x 480-60
  1024 x 768 - 60,70,75,85
  1152 x 864-75
  1280 x 720 - 50,60
  1280 x 768 - 60,75,85
  1280 x 800-60
  1280 x 960 - 60,85
  1280 x 1024 - 60,75,85
  1360 x 768-60
  1366 x 768-60
  1400 x 1050 - 60,75
  1440 x 900 - 60,75,85
  1600 x 1200-60
  1680 x 1050-60
  1920 x 1080 - 24,25,30,50,60
  1920 x 1200-60
  2560 x 1600-60
  3200 x 2000-60

  But it seems the resolution also depends on the GPU built in the notebook

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps

• Tecra Z40-A-176 - how to get support for high speed Port Replicator III?

  Hello

  a customer garage bougt some Tecra Z40 A 176 with high speed Port Replicator III. Unfortunally to either the displayport Port replicators is not working properly and I want to have the support so.

  What I found was the support for laptops page itself, but not for the port replicator.

  With regard to:
  Klaus

  I want to have the support so.

  What do you mean by support and what is the problem with the display port?

  If you have hardware problems, you can contact your dealer or contact the Toshiba authorized service provider that is available in your country.

• Portage Z30-A-13W connected to the high speed Port Replicator III - USB problems

  Hi all.

  We recently bought a new Portage Z30-A-13W and Hi-Speed Port Replicator III.
  Setting network and graphics work correctly with port replicator, but the USB ports don't work at all.

  I tried the port replicator USB 2.0 and USB 3.0 and I can't seem to work with a keyboard, mouse, USB key or a mobile phone.

  In the case of mobile phones, it is also no output power of the ports that the mobile does not start to load.

  At any one another experianced this problem and what was the resolution.

  Thank you very much

  Jonathan Davies

  Hello

  As far as I know additional drivers are not really needed to use the USB ports.
  This is why I m wondering why don t USB ports work.

  It might be possible that ports high speed Port Replicator III USB are faulty, but to be honest, I can't imagine that all 6 USB ports may bad work at the same time.

  So maybe it s a software problem.
  First of all, I would recommend the default BIOS and check the USB legacy support for keyboard and mouse could be activated.
  After access to the Device Manager and remove / delete the USB hubs and controllers in the list of devices.

  Keep high speed Port Replicator III connected to the computer and restart the device.
  Usually, the system should recognize automatically deleted USB ports and must update the drivers of USB ports.

  I hope that the USB ports don't work after this short workaround solution.
  Keep your fingers crossed.

• Portege R700: Speed Port Replicator HI + USB Vista questions

  Good afternoon

  I am having trouble with 4-5 new R500-1hd (311th short number), the number could be higher, but users could not have reported it.
  If the laptop is disconnected from the HI Speed Port Replicator 2, it off very well and the laptop can be used, but when the laptop is brought back it does not recognize the mouse or the keyboard. The device does not appear as an "unknown device" in Device Manager, but just does not at all appear.

  A new problem that has arisen is again when the machine is off station USB devices install\work not unless they are connected on port SATA\USB, once again the machine failed to detect at all. Even when devices are picked up, it may take in any case of 30-60 seconds before the work of the mouse and the keyboard.

  These are corporate images deployed through WDS and the problem is very intermittent.
  A reset is applied each time the device will be detected.

  I had a couple of flying machines and finished the stretch prior to the computer with Windows 7, computer image portable devices all work fine with or without the docking station and can be used instantly.

  Isn't anyone has an idea how I can fix this problem?

  Concerning

  Kris

  Hello

  As far as I know speed Port Replicator HI new supports the USB 3.0 standard.
  I found the USB driver on the European driver Toshiba for the USB 3.0 feature page.

  I recommend that you install this!

  Thanks for posting comments after trying that

• Need Advanced Port Replicator III drivers for use with my Portege M300

  Hello

  I have a Portege M300 with an Advanced Port Replicator III. I had to reinstall the operating system and now can not find the drivers for the port replicator.

  Can someone help me? I am running Win XP

  Thank you

  Hello

  I guess that you need drivers for the XP operating system. Am I wrong?
  You will find on the page of the Toshiba driver all drivers needed and utilities for Portege M300.
  You will also find the installation instructions document. This document shows the proper installation order.

  You simply download all the drivers and follow the order of installation. All that s

• Tecra M9 longer works with the Advanced Port Replicator III

  Hello

  I have the Advanced Port Replicator III Plus (PA3474E-1PRP), and it works very well with my M5 (M3 and M200). For example I connect my laptop through it to my monitor/mouse/keyboard/external DVD/hard drives, sound, webcam etc...

  Now, I'm to assess what should I buy as my next laptop and the M9 (PTM91E-03000MEN) seems good.

  Question: * the M9 will work with my plu III advanced port replicator? *

  Otherwise, * y at - it another docking station option that will allow me to connect a M5 and an M9 * please? (of course not at the same time).

  If there is no solution that allows a single docking station for the M5 and M9, then I might as well choose a laptop from another supplier... Main reason to stick to Toshiba all these years is the docking station compatibility that I move older models to the newest...

  All thoughts welcome...

  See you soon
  Daniel
  --

  Tecra M9 and Tecra M5 do not have the same docking connector.
  This means Tecra M5 is the APR III +, Tecra M9 has Express Port Replicator.
  You need the correct docker for each system.

  May it is a solution to be able to use the Toshiba Dynadock. It's USB based:
  http://www.dynadock.com

• Tecra M3 and Advanced Port Replicator III: not recognized as docking station

  Hello!

  Just install my new M3 and Advanced Port Replicator III. Everything works fine, but the Port Replicator is not recognized as a Docking Station (No disconnect in menu button start XP; pressing disconnect button on the Port Replicator itself has no effect either).

  Is TI WHEREAS behavior?
  Thank you in advance.

  Hello

  You reinstall the unit with the recovery CD?
  As far as I know that the TOSHIBA Mobile Extension3 for Windows XP is responsible for the good condition of the market of the docking station.
  Well, I recommend to reinstall this driver and utility.
  Perhaps the installation of the new driver will solve this problem.

  Good bye

• Port Replicator III + very high CPU when you move the usb mouse only in W2k

  Tecra M2 with a port replicator III +.

  It is set to dual boot XP and Windows 2000 (yes I know it is well a bit but I have a bunch of stuff installed in win2k it is difficult to find these days).

  XP is very good at 100%, but with win 2000 if I use my * USB mouse * on the * ports port replicator and waggle the mouse around - the * CPU * jumps from 0 to * 70 + % * use (System process that seems indicatates like IRQ problem). If I plug the mouse into the ports of the laptop (when the laptop is connected) - it's fine, no more than 5% cpu usage. It's a microsoft basic mouse. I really believe that this is a problem of usb any, because the cpu jumps a little if I type quickly on my usb keyboard (only a few %). It comes with the usb ports on all the Replicator.

  Any ideas? I don't really want to plug my mouse in the morning because it beats a little interest to have a docking station in the first place! I have installed mobile extensions. All other aspects of the replicator are fine

  Martin

  Huh it will not be easy to find the right explanation for this.
  At the moment when Tecra M2 has been offered on the market as Replicator port compatible Toshiba offered Toshiba Advanced Port Replicator III (no +) and at that time both supported in operating system has been tested with it.

  Toshiba later designed Toshiba Advanced Port Replicator III + and confirmed the compatibility with Tecra M2, but obviously with more recent WXP (at this time).
  So now, you've been following situation: you use most recent Replicator port, but with much older operating system so I assume that there may be a compatibility issue with W2K.

  I can't imagine use you so often with W2K and if so, may not be so problematic to connect the mouse directly on the cell s USB port.

  Sorry, but I don't think that there is nothing you can do about it.

• External keyboard works only after the restart with Port Replicator III Plus

  The problem is that when I start the laptop, the external PS/2 keyboard does not work. When I reboot keyboard this one turns around and then I can use it.

  This problem occurs on a laptop Toshiba Tecra with an Advanced Port Replicator III Plus. I used several keyboards, so this isn't the problem. I changed a value in the bios which is used for devices USB (mouse/keyboard). I disabled the option, because I use a keyboard and a PS/2 mouse, but the problem is not resolved. I hope someone has an answer to this problem.

  Hello

  It will be interesting to know what model Tecra you use. Is it perhaps Tecra A6?

• Tecra A8 and Adv Port Replicator III - no audio output from the port replicator

  I have a Tecra A8 anchored on an Advanced Port Replicator III. All ports (network, USB, video) with the exception of the AUDIO ports seem to work well. I can get sound from the headphone jack on the front of the A8, but nothing since the station docking ports. Is there a docking station driver or something I need to install to get the sound from the docking station not the laptop?

  Hello

  The Advanced Port Replicator III supports the line and line port left.
  As already suggested by user above; Check if you are using the command-line output port!

  Welcome them

• Tecra M3 & Port Replicator III wireless problem

  I just bought a Tecra M3 and a port replicator III. When undocked the M3 connects to my WiFi without problem and remains connected. Once anchored it continues to have problems connecting, despite full status of the receiver and after connection bar / disconnect for a while he just gives up and says unable to connect. If I disconnect then it can connect ok. Someone at - it ideas. It can see the network fails to connect properly.

  Hello

  Very simple to solve, you must upgrade the driver Intel Wireless 2200 b/g Intel 9.0.2.25 card or higher.

  Good luck

• Tecra S1 stops when you use the Port Replicator III

  Hello

  I ve you have a problem with a Tecra S1 Notebook and Port Replicator III. When I anchor the portable station, it turns off immediately. It doesn´t so serious I m in Windows or not. The same notebook works in a Port Replicator II without any problem. My first thought was, the Replicator III may be damaged, but I tried with an another Tecra S1 and it worked! Can someone help me with this?

  Thx a lot!

  Mathis

  Hello

  AFAIK that should not be any problem as Tecra can be used with the two PRs. The only thing I can recommend is to reinstall the Toshiba Mobile Extensions.

  Good bye

• Advanced Port Replicator III more compatible with the Portege R200

  I just ordered a new Portege R200 and above-port replicator... However, I note that the R200 is not listed in the list of laptops supported for this Replicator! Can anyone confirm if I have made a mistake and need to change the order?

  Will be

  I visited the area Options & accessories on the European site of Toshiba, and like you said the Portégé R200 is not listed in the list of mobile phones compatible.
  So I assume that the Advanced Port Replicator III more (PA3474E-1PRP) does not support the protected R series.