Latitude E5470 - Installation of Win 7 - No Drivers

Similar Questions

• Question about the installation of Win XP on Satellite Pro P200

  Hello

  I have a lot of problems with Vista. First it took me a week to install my printer WiFi. (sollution: install local lpt1 as the printer, change port properties en gives a location network (computer/printername).)
  Last problem: vista give no right to copy my USB hd protable with xp files.

  Finally, I lost all hope and want to go back to xp.

  Is there anyone with experience in the installation of win xp on this laptop. And is it possible to tell me the steps that you have been taken to do so.
  Are there concerns as none have some drivers, things that do not work or problems with sata hd.

  Thank you

  Luke

  Hello

  It's a difficult topic-> XP on Vista machines.

  First: Yes, you can install XP on it because all the important factors are available (VGA, SATA, wireless, XP BIOS, BLUETOOTH) and that should be enough.

  Because your computer has a BIOS for Vista (I guess there a) Please install the BIOS XP first and then start the installation of XP. In the case that your HARD drive is not recognized then you need to install the SATA driver during the installation of windows XP. The procedure is described in the statement of the Satellite L40-> XP installation, so if you want to install and problems SATA (HDD, not during the XP installation), you must check the installation instructions for Windows XP for a SATELLITE L40!

  If you have additional questions, I recommend allows you to place your question here before doing something that may stop your nerves later. :)

  Welcome them

• Problem using Toshiba Software Installer for Win 7 on Satellite L750-1MT

  Hello!
  I have the problem with Toshiba Software Installer for Win 7 on Satellite L750-1MT (PSK30E-02T002B3) with no preinstalled operating system.
  I do the following:

  1. install Windows 7 x 64 SP1.
  2 Installing the LAN driver (device was not recognized by Windows 6) (downloaded from [http://se.computers.toshiba-europe.com/innovation/jsp/supportMyProduct.do?service=SE&LNG=26&userAction=S MP_RESULTS_PAGE & partNumber = PSK30E-02T002B3 & serialNumber = & USER_ACTION = Serial % 20number])
  3. install all updates of Microsoft Windows
  4. run the installer of the software Toshiba for Win 7 - it installs two drivers and then asks to restart.

  Here is the log for the first test (win7update.log) file:

  12\28\2011 update started at 21:11
  TVALZ_O.inf installed
  E/s installed & memory access driver
  driver_bluetooth_TC00241200A.exe/s/log/test has been installed with the result of the PASS code
  util_tvap_TC00215000H.exe/s/log/test /wait15 was installed with the result of the PASS code
  Updated at 21:29

  After the restart I've run it again and the result is:

  12\28\2011 update started at 21:38
  Toshiba Bluetooth stack has already been installed.
  Toshiba value added package has already been installed.
  Updated at 21:40

  Any help is appreciated!
  Thanks in advance!

  Stand by.
  What are you doing exactly?
  You try to install own OS?

• Trying to regenerate my installation of WIN 8

  I am trying to update my installation of WIN 8. I have problems of pilot (optical drive and virtual disks) and I hope that this will help with.

  When I try to WIN 8, it says that some files are missing, and I need to insert my media. It is a download and I have no disc to be inserted.
  When I try to run the original downloaded file (Windows8 - Setup.exe), she prays for my product key. When I give him the key, it tells me that the key is an upgrade, and I can't move forward.
  What I have going on here?

  Thank you, Mary Therese K... With the help of another forum, I managed to get a new product code. With that, I used my previously downloaded file to renew my program to WIN 8. By doing this I have now all my back drivers where they belong and everything seems to be fine.

• Installation of Win 7 RC on HP Pavilion DV6-1130sa

  I have the following questions regarding the installation of Win 7. The disc is currently containing the Vista partition and the recovery partition. I want to install then I 7 RC as a new installation on drive C with the possibility to go back to Vista if you need and have the laptop works on the original factory configuration.

  (1) if I do a fresh install of Windows 7 on the hard drive with Vista Home pre. 32 bits (including the recovery partition), the recovery partition will stop working (IE from the trunk F11 option included)?

  (2) if the recovery partition does not work afterwards, if I use my restore dvd copy I ve created, it will create the restore disk partition hard like it was form the factory? and let me go back to vista home Prem

  Please let me know if there is anyone out there who have tried the above with their HP laptops.

  Thank you for your time to help me.

  Ruwsoft

  Hello

  First make the Vista backup. How all the information here.

  (1) If you leave parition your recovery there is work.

  (2) so it does not restore partition, it will automatically recover your system.

  You might also be interested in dual boot.

  This way you will have the possibility to use the two system on a laptop computer.

  How dual boot Windows Vista and Windows 7 (Vista installed first) information here

• Qosmio F20-141 - cannot start the installation of Win XP PRO SP2.

  Failed to start installation of Win XP PRO SP2.

  After click on "Start of the CD" I can see for a short time only from message ~ "Install from XP Wisdows" (small white letters at the top of the black screen)

  After this computer hungs in black screen.

  QOSMIO F20-141 for the Federation of Russia
  M/N: PQF20E-02801YRU

  Hello

  Have you used the Toshiba Recovery CD or did you install the operating system from the original CD of Win XP?
  As far as I know the recovery procedure is very easy to use and it should work without any problems.

  Good bye

• My original OS 7 Home Basic Edition (purchased): problem of Installation of Win 10

  Windows has AUTOMATICALLY upgraded to Win Ultimate who, as the replies received from your good end, has been described as false.

  To date, I had downloaded (free) Win 10, but when installing, I received a msg stating putting touches of the original VER of Win 7 Home Basic Edition (which I bought) and then click Refresh.

  Please notify: (a) I would require to REINSTALL my house 7 the CD database (since upgraded Ultimate is false since it was produced Acer OEM - SLP Win 7 Ultimate, and mine is customer built Gigabyte motherboard) before Win 10 could be installed.

  (b) if I didn't need to REINSTALL WIN 7 Home Basic, then how and where to insert the product keys (for Win 7 home basic) to allow the installation of win 10?

  Windows 7 can not auto-level to a ultimate edition. He must intentionally upgraded or a non-genuine Windows 7 Ultimate product key has been used for the Express upgrade.

  Your best option is to reinstall Home Basic, reactivate and then upgrade.

  Or, if you have basic Windows 7 Home Edition product key, you can use it to perform a new installation:

  How to install and activate Windows 10 using your Windows 7 or Windows 8 product key

  Resources:

  How to download official Windows 10 ISO files

  How to: perform a clean installation of Windows 10

• BSOD after fresh installation of Win 7, failure of page in the nonpaged area. Win 7 will not install

  A day at the start of a program on my computer that I used for years without incident, the computer suddenly fell down, restarted, and I got the infinite loop of system repair. No change in hardware/software, don't know if a recent Windows Update has been installed. Once again, CPU, mobo, Vid, RAM are the same for the past 4 years.

  After much frustration, I decided to just reinstall Win 7. So I deleted my partition, re-created a new partition and installed Win 7

  In the last step of the process of installing Win 7, it says Setup cannot complete. It is then stuck in a loop of reboot with a BSOD page fault in non paged area.

  I tried F8 on startup and choose Safe mode, but then he says that the installer cannot boot mode safe because the installation of Win 7 did not finish.

  I tried to reinstall Win7 by removing the disc again, but I get the same results.

  What can I do?

  HI - finally got the job. I had the computer to use only the GPU on board BIOS and was able to install. Somehow the graphics driver conflict when Windows is first installed and it kept crashing.

  Thanks for your help.

• During the installation of Win - xp pro vmware error 10 as mentioned below

  During the installation of Win - xp pro in 10 vmware, it is showing "OPERATING SYSTEM IS NOT FOUND" how to solve. I scoured the file .iso record and properly connected to all readers. Help me solve this problem.

  I think you'd have better luck if you go to the website of VMware support.

  http://www.VMware.com/support.html

• email nach neu installation von win 7 software download as photoshop 8

  email nach neu installation von win 7 software download as photoshop 8

  Direct download links for Adobe software

  Mylenium

• Need drivers after installation clean win 7 on win 8 machine

  Curve minimum smarts learning difficult for an old man with a computer. Try to restore a HP 500-075, which came with Win 8 installed and upgraded to 8.1. A day after the reboot, I couldn't past password logon screen (I had not created one). After much googling that didn't serve me without success, I gave up and decided to reinstall the OS, but instead to install Win 7, didn't like 8 in all. Bought a drive OEM installation and after a lot of help from online, managed to install it. But no drivers. When I look up the drivers available at HP for this PC there is not an option for Windows 7. So my main question is will drivers for 8.1 work now that 7 is installed. Or I have to go back to 8? Moreover, I try the option of restoration of HP at the start, but was caught in an infinite loop. I'm about to launch this box and buy a new one!

  Bill, welcome to the forum.

  As one old man to another, I suggest you save yourself some frustration and come back to Win 8.  We can probably find some drivers for the computer, but you may have problems because the computer is equipped with a UEFI BIOS with Secure Boot.

  There are a lot of very good guides available to help you learn how to use Win 8.1.  I have a desktop with Win 7 and a laptop with Win 8.1.  I'm going from one to the other without any problem at all.  However, I use the desktop with Win 8.1 computer most of the time.  In fact, it is possible to start directly on the desktop instead of the start of Metro screen.  Here's a guide that will help you do it.

  Once you have read the guide and tried to use the desktop computer, if you want to continue using Windows 7, I'll see if I can find the drivers for you.

  Please, click on "Thumbs Up +" if I helped you and click "Accept as Solution" If your problem is resolved.

• Satellite P855-31V: some problems after the installation of Win 8.1 and drivers

  After that installation of 8.1 of Windows and updated drivers have problems:

  1. the switch market/no work
  2. flight mode button not work
  3. ECO button not work
  4. applications not available menu home

  Notebook * toshiba satellite p855-31v *.

  Could you help me please?

  Usually very important to install and update the drivers in the correct order.

  The + installation instruction doc + you can find on the page of the Toshiba UE (Windows 8.1 update) driver provides this order:

  1 Intel Wireless display uninstall
  2 windows 8.1 update to install
  3 TOSHIBA Assist Desktop Upgrade
  4 Intel Display Driver upgrade
  5 NVIDIA Display Driver upgrade
  6 Intel Rapid Storage Technology driver upgrade
  Update 7 Synaptics Touch Pad Driver
  8 update of Realtek Wireless LAN Driver
  9 Intel PROSet/Wireless WiMAX software update
  Update the driver from Tuner DVB-T/ATSC of 10 YUAN
  Update driver TOSHIBA 11 Support
  Upgrading TOSHIBA 12 system pilot
  TOSHIBA 13 function key upgrade
  14 TOSHIBA eco Utility v2 upgrade
  TOSHIBA 15 fingerprints digital utility upgrade
  TFPU 16 WBF deleting fingerprints tool upgrade
  17 TOSHIBA HDD Protection upgrade
  18 TOSHIBA VIDEO PLAYER Upgrade
  Update of the 19 TOSHIBA Blu - ray disc player
  20 TOSHIBA PC Health Monitor Upgrade
  CyberLink MediaShow 6 21 for upgrade TOSHIBA
  ArcSoft 22 TV5.0 update
  Plug-in for Windows Media Player upgrade 23 TOSHIBA resolution +.
  24 TOSHIBA Media Player by TrueLink + Upgrade sMedio
  Update 25 TOSHIBA Service Station

• Satellite U940 PSU6SA - installation of Win 7 ask for HARD drive drivers

  Hello

  not sure whether to put this under "Windows 7", Mods please move as necessary.»

  I have a ultrabook Toshiba U940 PSU6SA - 02K 002 that came with Windows 8 (not Pro) and I would like to install windows 7 on it. It has a Hitachi 500 GB and a small mSATA SSD 32 GB.
  It works already latest BIOS Toshiba 1.30.

  I turned off safe start-up and UEFI, can I start and start the windows 7 installation from USB, but it is looking for additional drivers that I can't work. I have tried various drivers of windows 7 Toshiba has had on their site for the 940 Ultrabooks but without success. (Driver Intel Rapid Storage Technology, Intel Chipset Software Utility, driver USB 3 and Intel Display Driver).

  I'm unziping the drivers on an another USB and installation is to find them, but they seem not to be what he wants.

  Any suggestions or a guide? Thank you

  What you need is the SATA driver that must be loaded before Win7 installation doesn't start.
  Please download it from here.

  I used to install Win7 on my U940.

• Latitude E5470 W7x86 drivers missing downloads

  The drivers download page lists more x 86 drivers for W7?  There are a few months before, but not now, and I was not able to find anything about it either by declaring that W7x86 support has been ignored.

  The problem is resolved.  Dell support reactivated the x 86 list W7 drivers in the drivers download page.

• Re: Installation of Win XP on Portege R500 12 q

  Hello
  I would like to install Microsoft Win XP on my Portege R500 12 q (128 GB SSD drive)

  If I start the installation of the CD, there is normally the possibilety to install a third-party driver through by pressing F6. But the problem is, that nothing happens if I press F6 at this time (tried more than once).
  OK if I wait, I get the possibilety to specify the mass storage, because the installation program does not find any. If I want to install the drivers now, is the only possibilety to install drive A: (floppy drive) but I don't have a floppy drive.
  I have not found the driver SSD - to the Hompage, but I think that it is included in the Matrix Storage Manager, isn't it?

  It is really difficult to install Win XP on a SSD? Please help me.
  Thanks in advance.
  Greetings
  Stefan

  > Ok if I wait, I get the option of specifying mass storage, because the Setup program does not find any. If I want to install the drivers now, the only possibility is to install from drive A: (floppy drive), but I put t have a floppy drive.
  If you want to include the SATA driver using the F6 option then you MUST USE the floppy drive. But if you have a USB floppy drive, then you can use nLite software to include the SATA drivers in the new created XP CD.
  The SATA driver is part of the Intel storage Manger and you can download if from here:

  [Intel storage utility eat 32-bit Configuration diskette (201ko) 8.6.0.1007 | http://downloadcenter.intel.com/download.aspx?url=/17061/eng/f6flpy3286.zip&DwnldId=17061&ProductID=2101&lang=e ng]

  For more information about nLite Internet search!

  > If I change the setting again in the bios I always get a blue screen, but I can't install the driver of the matrix (SSD) as long as I n t, setting change and I think I don t use the SSD speed possible.
  It is clear. You will always get a BSOD if you would replace the SATA mode in the BIOS after installing any OS. If you have installed the operating system, you can not change the SATA mode in the BIOS.
  But if you want to change it again once, then you will need to install the new OS using the SATA drivers

  Good bye