Linksys 8-port befsr81b and CR-smcd3g cable/dsl router

Similar Questions

• I just bought a keybboard ultra thin logitech for iPad air. It has a port for a small cable, but no cable in the box. What is the port for, and what don't get me?

  I just bought a keybboard ultra thin logitech for iPad air. It has a port for a small cable, but no cable in the box. What is the port for, and what don't get me?

  Have you tried the Logitech support site?

• Cannot establish network connection. Messages on the icon alternate between "Acquiring network address" and "unplugged network cable.

  Original title: cannot establish a network connection

  Very well, a computer can connect to the internet. Another computer using the same modem cable and fixed connection of the router (for example using the port adapter, not wireless) Wireless does not connect. I suspect that there are has some settings somewhere that are not correct. Can you tell me how to understand where is the problem?

  Messages on the icon alternate between "Acquiring network address" and "unplugged network cable. When I run troubleshooting this is what I get:

  Diagnosis of IP Configuration
  Invalid IP address
  Info	Zero (0.0.0.0) detected IP address
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: reset the network connection
  action	Disabling the network card
  action	Activation of the card network
  Info	Successfully activated network adapter
  Info	Zero (0.0.0.0) detected IP address
  action	Repair Manual: Reboot modem
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  Info	Redirect the user to support call

  WinSock status
  Info	All base service provider entries are present in the Winsock Catalog.
  Info	Winsock Service providers strings are valid.
  Info	Entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.
  Info	Entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.
  Info	Entry provider RSVP UDP Service Provider managed the loopback communication test.
  Info	Entry provider RSVP TCP Service Provider passed the loopback communication test.
  Info	Connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter
  Network location detection
  Info		Using the Internet connection at home
  Identification of network adapter
  Info	Network connection: name = Local 2, Device network connection = Intel(r) 82562V-2 10/100 Network Connection, MediaType = LAN, type = LAN
  Info

  Ethernet connection selected

  State of the network adapter

  Info

  The network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn

  FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  warn

  FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  error

  Could not make an HTTP connection.

  error

  Could not make an HTTPS connection.

  error

  Could not make an FTP connection.

  I found the problem (s), even if I am always left with a few questions.

  During this process, I have disabled the firewall, but that did not help. However, I noticed 'tweaks' accessed via the tab 'Advanced' in 'Microsoft Firewall' which looked like, they must be checked in order to access the internet. I checked these and reintroduced the firewall. After I got things working, I unchecked them and things still worked so I obviously don't understand what these parameters.

  The solution:

  (1) I have to go straight from the modem cable to the computer. I can't have a cable modem, router wireless, computer, even if using hard wire, and even if this same configuration works with another computer. Also, I can't use a cable length to go from modem to the computer. So, it seems to have had a problem of cable length. Power problem? Only connected to this computer devices are the mouse, the keyboard and the Ethernet. Would not this be fixed with an upgrade of the power supply? Or is it due to the quality of the Ethernet hardware on the motherboard? It's a Dell Vostro 200.

  (2) in back and forth between configurations while following the problem, you must think to unplug the modem to reset between each configuration. You may have stumbled upon the solution, otherwise he's not shot. Also, I unplugged the cable from the modem when you reset data cable - do not know if it was necessary. I wanted to limit the degrees of freedom that I had a lot, as it was.

• E4200 and Arris TM702B cable modem

  I bought this router and expects a lot from it, but not what happened when dl a file: its starts enthusiastic and reaches up to 8000 Kbps, but unfortunately my cable modem loses internet contact then (seems to reset or accident or both). My network is fine, it's just the internet connection.

  I have updated the firmware of the E4200 (FW_E4200_1.0.02.013_US) and reset the router: no joy.

  Claimant stated that my modem is OK, but that leaves me with this annoying problem!

  Can someone help me please?

  Try these steps-

  Move the far the arris of telephone cable modem router... use of cordless telephones 2.4 Ghz also run a speed @ speedtest.net test and a ping test @ pingtest.net, and also keep all wireless phones away from routers, I found a huge improvement in my router speeds and no lag or dropped connection! also tips to improve your speed-

  MTU - MANUAL - 1365

  CHANGE THE BEACON INTERVAL-75

  THRESHOLD RTS AND FRAGMENTATION-2304

  FILTER ANONYMOUS INTERNET - PEOPLE WITH DISABILITIES REQUESTS

  FILTER MULTICAST - PEOPLE WITH DISABILITIES

  FILTER INTERNET NAT REDIRECTION - PEOPLE WITH DISABILITIES

  FILTER IDENT (PORT 113) - ENABLED

  QOS - WMM - ACTIVE

  UPNP-ENABLED

  SAVE THE SETTINGS

  access the router to change these settings - type 192.168.1.1 and enter admin, and the password (that would be your router password) or cisco software click router connection settings then click on advanced settings, then click ok, and then manually configuring the router

  This should also improve your 5 GHz & 2.4 Ghz speeds and make sure you have wpa2 password protected it and I am sure you will find a shocking improvement as I did in the speeds and singal...

  you will see a significant improvement in singal, I discovered cela if trail and error even had cisco replace my E3000 due to connection problem when all along, it was my cable modem wireless!  I would come down the router about an inch or more away the ARRIS cable modem! Good luck! my router went from 54.0mbps to improve 144.0mbps - so try to move the router away from the modem, it worked for me and there is a difficulty

  CBerry173

• NAS hard drive not accessible more: the device is not configured to accept connections on port 'files and printers sharing (SMB).

  Dear,

  I am desperately looking for a solution for my specific problem how access my NAS.

  I have a hard drive from Western Digital NAS (Book Live) which worked fine until now. Yet, I just changed my internet provider and I now have a new Fritzbox 6360. Now, I can not access the hard disk of the commune of programs in Windows. I contacted two suppliers already, but without success. I think I have some incorrect settings in my Windows 7, 64 bit. This is the situation:

  -NAS is still working with my old Fritzbox, for testing that I went back-> ok

  -I can access the NAS via the dashboard or a TwonkyServer-> ok

  -When I access it via Windows Explorer, I wonder is to give my credentials (which don't work) or I get the error message: the device is not configured to accept connections on port 'files and printers sharing (SMB).

  -J' changed my IP address (dynamic even static) and connections, password-> without success.

  -J' tried SFC with the result that found no violation of integrity. -> ok.

  Any idea?

  Can you please turn off the NAS, unplug the cable and Ethernet cable? Wait about 2 minutes then plug all the cables back in. Any security program or firewall to this computer? Try disabling it for now.

  You have another PC or laptop which has Windows 7/8 and try to access the NAS?

  You have a smartphone or a Tablet and download an application for the WD NAS and then try to access files.

• RV042 open ports 80 and 443 to Shields UP! When using QuickVPN

  Is it possible to use QuickVPN with the RV042 without leaving ports 80 and 443 open to Shields UP great! scans?  As a solution, I'm pass these ports to a non-existent IP address and forcing QuickVPN to use 60443 port.  Yes, 60443 watch also opened too if I scan it, but at least it is not in the ports first 1056.

  Any help much appreciated.

  Router Linksys brand is using the latest firmware for this material (1.3.13.02 - tm)

  Tim,

  As shields up is a very good tool to run inside your network to get an idea on what ports are open. It is best to run the scan of a computer that is not behind your network. I use nmap http://nmap.org/ and scan my network from the outside to get a better idea on which ports will show open. Since Shields up is running on your computer, it will display the results based on your computers as firewall. Yes Qvpn requires 443 or 60443 to be tuned by the router to establish a connection.

  Thank you

  Jasbryan

• This computer has an add-in graphics card and the monitor cable is plugged into the integrated video connector.

  I tried to connect a new TV to my 8700 with HDMI and I get this message:

  This computer has an add-in graphics card and the monitor cable is plugged into the integrated video connector.

  1. power off the computer
  2. plug the cable from the monitor into the graphics add-in card connector. This may require a video card or the video adapter cable.
  3. turn on the computer

  I unplugged from the back of the computer and put it in my drive macbook & blu - ray. Both worked.

  I tried to find a solution to this already, but none really helped.

  Thank you.

  You need a video card, not the port on your computer HDMI connection:

  

• Airport Time Capsule 3 to port usb2 and usb3

  Is the usb to Time Capsule on the new Time Capsule 3 to port a port USB2 and USB3?

  A USB 2.0 port.

  (141391)

• How do the 5 server not listening on ports 80 and 443

  I want to configure an Apache Server on a Linux virtual machine (using the last VirtualBox) on my Mac running El Capitan 10.11.3.

  5.0.15 server is already running on the Mac (and I want to keep it, with the exception of web services). I have disabled the sharing in the web server user interface, but it was not enough, Apache listening ports 80 and 443, prohibiting VirtualBox to listen to them and transmits them to the Linux virtual machine.

  So I put comment out these lines in /Library/Server/Web/Config/Proxy/apache_serviceproxy.conf:

  #listen 80

  #listen 443

  8008 #listen

  #listen 8800

  8443 #listen

  8843 #listen

  After a restart, Apache seems not to listen to ports 80 and 443 more. However, VirtualBox does not become the listener. I tried this command in the Mac terminal:

  -i sudo lsof: 80

  and nothing has been returned, suggesting that something in OS X still prevents VirtualBox to listen to ports 80 and 443. If I try to convey some random host port of Mac to port 80 in the virtual machine, then I can my virtualized server access from Safari on the Mac host via the custom port said. But I would use the standard port 80.

  Any help really appreciated.

  Instead of commenting, assign a specific IP for the server listen instead of * (which means that all the IP addresses). This is only to the server on port 80 and 443 in this config file. I sometimes give an additional IP address to the Ether. Your Linux Machine can connect to the second IP address or the first initial assigned to your server depending on your configuration.

  Server is very aggressive in it's use ports, he leaves so all services to operate, even if you have the use of ports to other IP addresses.

  Leo

• HP DC7700: Serial Port PCI and simple Communication controllers pilots missing in HP DC7700 windows 7 (32 bit)

  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2997 & CC_070002
  PCI\VEN_8086 & DEV_2997 & CC_0700

  and

  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2994 & CC_078000
  PCI\VEN_8086 & DEV_2994 & CC_0780

  Experts in the House should please come to my rescue.

  I just upgraded my Hp DC7700. I was able to get all the drivers except for SERIAL PORT PCI and PCI SIMPLE COMMUNICATIONS CONTROLLER missing. above are the two missing pilots hardware ID

  Hello:

  There is no W7 drivers for these devices.  You must use the Vista drivers and if auto installation does not work, you will need to install the drivers manually by navigating to the folder of the driver that was created when you ran the file from the device in the Device Manager (browse my computer for driver software).

  This package contains the driver Intel Host Embedded Controller Interface (HECI) for access to Active Management Technology (AMT) initiative of the Intel Digital Office for rated desktop models and operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34743.exe

  This package contains the Intel (LMS) Local Management Service and Serial - over - LAN (SOL) support for the technology of Directors Active (AMT) under the Initiative of digital office Intel for the supported desktop models and
  operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34744.exe

• Portege R500: external monitor does not work with the Port Replicator Port 2 and DVI

  I have a Portege R500 running Vista with a slim Port Replicator II and digital monitor Viewsonic.
  I connected the monitor to the DVI port on the port replicator and got it to work OK.
  Press fn + F5 would switch between the computer screen and the external monitor.

  Then it stopped working, and I can't make it work at all. F5 recognizes just the laptop screen.

  If I connect an analog display, it is fine, and I can pass between the two screens without difficulty.

  The strangest thing is that, if I reboot when the Portege R500 is docked, the digital monitor begins by displaying the boot sequence, but then the signal is lost as soon as the screen stops the display of the progress (in low resolution) bar.

  I spent an hour on the phone to support Friday, and he made me nowhere.
  They finished by saying that he should never have worked! So what is the DVI port because then?

  Any ideas?

  David

  Connect your monitor directly to your laptop and see if it is recognized and you can go through FN + F5 between the two views.
  If it works, then connect with port replicator, and then try again.

  It's probably best if you reinstall display drivers. Maybe there are new too on the download page.

• Serial port PCI and PCI Simple Communications Controller

  Hello!

  My computer OS is Windows 8.1.

  I just shearch something and I found that... I don't have serial Port PCI and PCI Simple Communications Controller. (Unintalled)

  Serial port PCI-> VEN_8086 & DEV_29B7 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 1 b

  Controller PCI Simple Communications-> VEN_8086 & DEV_29B4 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 18

  Sorry for my English. But can anyone help me?, where I can download these files.

  Hello:

  Here are links to the drivers you need...

  Install PCI Simple controller Comms

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78668_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Install PCI Serial Port:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78665_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• To set up my drive Web told me to "make sure that Ports 2077 and 2078 are not protected by a firewall... How can I find this information and if a firewall, how do I change or correct 2077 and 2078.

  I'm trying to implement a web disk with Hostgator for my blogs and the problem seems to be on my end, not theirs.  If I have a firewall port problem which prevents me from using my drive so what other options can I?.  Also what are the Ports 2077 and 2078 on my firewall.  How can I fix the problem?  Should I switch the disk and just use my desktop computer?   I wanted to keep the Hostgator on the disk. Also, I have the same problem if I jump the disc.  My 'add a network' don't like what I'm doing!

  Your message isn't clear when you refer to "floppy disk".

  In general, a firewall is designed to avoid that other computers access to your computer - unless you want that to happen.  You can add an 'exception' to the firewall that allows the software installed on your computer to communicate through the firewall, or you can open 'holes' (aka port) in the firewall that remain open regardless of whether an application on your computer is actively using them.  The latter is obviously a bit more risky.

  How to configure these exceptions depends on which firewall you use.  If you have Windows XP service pack 3 and you are using Windows Firewall, see http://windows.microsoft.com/en-US/windows-vista/Open-a-port-in-Windows-Firewall (well that article is on Vista, it applies as well to the firewall of Windows XP sp3, except instead of step 2, just click the 'Exceptions' tab - and don't forget to uncheck the box in the "General" tab that says "don't allow exceptions").

• opening ports 2077 and 2078 to use web disk

  Hello, I can't see my web files with webdisk and I would like to know how to manually open ports 2077 and 2078. I already read an article on the Microsoft Web site, but form a certain point the indication does not match what I see on my screen. Thank you

  Which firewall do you use?  If the built-in Windows Firewall, open the Security Center in Control Panel and select the Windows Firewall applet.  Select the Exceptions tab, and then click Add Port.  Specify your port.  Use the button change the scope to restrict the port to the correct network or IP addresses is not wide open to the Internet (unless that's what you need). Brian Tillman [MVP-Outlook]
  ------------------------------
  If a response may help, please vote it as useful. If a response to the problem, please mark it as an answer.

• WRT320N - loss of internet connection after redirect port 80 and 443

  Hello

  I have a problem with my new WRT320N. When I activate the port forwarding on my local server (ports 80 and 443), after a while I completely lose internet connection on all my computers connected to the router (wifi and lan computers). The router itself can ping and trace any Internet site through diagnostics to Web administration. When I turn off and click on save changes button, my internet connection works immediately again. I have the latest firmware installed and I tried to reset the router several times and set it manually since the beginning.

  My previously detained WRP400 has been configured to redirect these exactly the same ports and everything worked perfectly. Could someone advise me where could be a mistake? Thank you.

  I solved it. There was a problem with the combination of the service 'DHCP Reservation"of the router and client DHCP of Ubuntu. I disabled "Booking DHCP" and set the IP settings manually in the Ubuntu computer and now it works perfectly