Loop "Failed to setup of the Windows updates"

Similar Questions

• Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

  I got an error message in step 2 of configuring updates - "updates were not correctly configured.  Returning from changes' anyone can help solve this problem?

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates
  http://support.Microsoft.com/kb/949358

• Error "Failed to setup of the Windows updates"

  Hello

  Have a brand new asus xc550c who had the updates installed and loaded, frozen, then went to the screen "reverting the changes windows features Configuration failure", paste here for two hours and counting.

  I can't restart the computer, like the Asus has a soft stop, which means that I only get the same screen on startup. Basically, I am unable to do anything at all with my laptop. All other threads assume that you can access the start menu, but it's impossible.

  What is the solution to this problem?

  Original title: Windows 8 update problem

  Hi aaronbeard,

  You did changes to the computer before this problem?

  I can understand how it can be frustrating when things does not work.

  Adding to suggestions from Shawn "Cmdr" Keene [MVP], you can try the suggestions in the following article and check if it helps you in fixing the issue with Windows updates.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

  http://support.Microsoft.com/kb/949358/en-us

  Note: After troubleshooting, consult this section «How to reset the computer to start normally after a boot minimum troubleshooting»

  System Restore warning: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  Hope this helps, if the problem persists with Windows updates, please get back to us. We are here to help you.

• "failed to set up the windows updates. returning from changes. do not turn off your computer.

  Hello

  I get this error "failed to configure windows updates. returning from changes. do not turn off your computer. The computer is a Samsung Ativ tab 5 and I got it for a little over a week.
  I have updated with the SW update
  The results of the troubleshooting online are:

  Problems encountered:

  Recent updates - not fixed installation problems

  Search for missing or corrupted - files detected

  Some security settings are missing or have been modified - fixed

  Registration for the service is missing or corrupt - fixed

  Windows Update error 0 x 80070490 (2014-02-10-t-11_25_11A) - fixed

  I have been through ALL the steps as described in http://support.microsoft.com/kb/949358. I have had no success.
  One thing that bothers me, is in the configuration of the system, I have a service called true vector Internet Monitor (Zone Alarm) and when the value disable as in http://support.microsoft.com/kb/929135, it is the only service still running when you perform a clean restart. I don't know if this affects the Automatic Updates/configuration or not.

  Hello

  Thanks for trying to help. Now my computer seems to be up-to-date.
  I followed your steps but MicrosoftFixit50202.msi did not like "my OS is incompatible. I use windows 8.  I couldn't run this in default or aggressive.
  I did go in Control Panel and disable antivirus and firewall Zone Alarm and reset Windows defender by default.
  I did IE default web browser I have prob changed when I got to the computer.
  I then returned to set up a clean boot and this time I managed to disable the true vector Internet Monitor (Zone Alarm) to run.
  I ran the reset troubleshooting of Windows with the same result as before is to say:
  Recent updates - not fixed installation problems
  Search for missing or corrupted - files detected
  I think I have restarted my computer at this stage and then tried to update again.
  It has not yet, but with the error, I got an error code and a link to help. I don't have not noticed this before. I followed the help and ran about 5 command prompts that have to do with the renaming of files I think.
  Then I tried updating again and this time 38 45 updates succeeded. I then ran the update again and it seemed to work on the other 7 updates.
  Although Windows Update said I was now updated, I was skeptical as when this whole thing started is started when I got the "windows installs updates" and then "failed to configure updates. Returning... etc"then I restarted my computer. At the start, there was no message on try to configure the updates, then, how do I know they are configured and working as it should?
  Thank you.

• Configuration of the windows updates failed, returning error Exchange

  I have a laptop windows 8.  Whenever I run windows updates, I get the error message "failed to setup of the windows updates, returning error changes.  I tried the windows update troubleshooting tool and download the updates manually but still no change.   Is there a solution to this?

  Thank you.   Often, when I try to run windows updates I get error like 80242FFF codes; 800703F1.

  Hi Zurkon,

  Thank you for your update on the issue.

  If you receive Windows Update error 80073712 0 x or 80073712, it means that a file needed by Windows Update is corrupted or missing. Windows has tools that can help you solve this problem of troubleshooting. I would suggest trying the following methods and check if the problem persists.

  Method 1: Run the Windows Update Troubleshooter

  • Run the Windows Update utility, then open Windows Update and try installing the update again.

  Method 2: Run the DISM tool

  1. Enter in the right edge of the screen and then click on search.
     (If you use a mouse, point to the lower right of the screen, move the mouse to the top and then click Find.)

  2. Enter command prompt in the search box.

  3. In the list of results, slide down on or right click command prompt, and then press or click Run as administrator.

  4. In the administrator: command prompt window, enter the following commands. Press ENTER after each command:

     DISM.exe / Online/Cleanup-image /Scanhealth

     DISM.exe / Online/Cleanup-image /Restorehealth

  5. To close the administrator: command prompt window, type Exit and press ENTER.

  6. Run Windows Update again.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• "Failure of configuration of the windows updates". error: WindowsUpdate_80070003 / 0 x 80070003

  Original title:

  "Failure of configuration of the windows updates".

  Hello

  I use Windows 8 and updated to 8.1 last month after graduating from the messages on HP laptop. As soon as I updated to 8.1 it stopped working correctly. It has become very slow and I was unable to perform any task. I went back to Windows 8, once I had this option. Since then, I get this error message «Failure of configuration updates windows.» Restoration of the changes. Do not turn off your computer. »

  I also tried the clean boot troubleshooting mentioned here: http://support.microsoft.com/kb/929135

  However, I get this error: WindowsUpdate_80070003 / 0 x 80070003

  Please help ASAP!

  Hi John,.

  I will try to help you with this question.

  Thank you for the information provided. Coming to the question I would like you try these steps and check if that helps.

  Method 1:

  Try the steps from the following link and check if that helps.

  Error code Windows Update '0 x 80070002' or '0 x 80070003 '.

  If you still experience the issue after trying the steps in the above link, try the following steps:

  Method 2:

  See the following article try the steps that you have not yet tried and check if that helps.

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

  http://support.Microsoft.com/kb/949358 

  Note: Follow How to reset the computer to start as usual after a clean boot troubleshooting article KB929135 to reset the computer in normal mode. Also when you do the system restore, you will lose data and the programs that are installed on the date you make the system restore.

  Make sure that you back up the data on the computer before performing all the troubleshooting steps.

  Method 3:

  If the previous step fails then please go ahead and try the following steps:

  I suggest to rename the pending.xml file, and then change the registry.

  a. boot from the DVD of Windows 8.

  b. click on repair your computer.

  c. click Troubleshooting, and then select Advanced Options.

  d. Select the prompt option.

  e. Once you open the command prompt, enter the following command and press ENTER.

  f. type cd C:\windows\winsxs, and then press ENTER.

  g. type ren pending.xml pending.old, and then press ENTER.

  h. system cannot find the specified files

  i. type regedit and press ENTER.

  j. select HKEY_LOCAL_MACHINE.

  k. on the file menu, click on load the hive.

  l. find the following folder:
  C:\windows\system32\config\components

  Mr. When you are prompted for a name, type Offline_Components.

  n. in the registry editor, locate and delete the following registry subkey:

  HLKM\Offline Components\AdvancedInstallersNeedResolving
  HLKM\Components\AdvancedInstallersNeedResolving
  HKLM\Components\PendingXmlIdentifier
  HKLM\Offline Components\PendingXmlIdentifier

  o. quit the registry editor, type exit at the command prompt, and press ENTER.

  p., click on restart.

  
  Note: the steps mentioned below include editing the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Please return to the State of the question.

• default configuration of the windows updates, coming back from updates.

  whenever I start my computer, it says "failed to configure windows updates, returning changes." It wont even let me start normally. HELP ME PLEASE!

  Hi Chrisuzumaki,

  This problem could occur due to these reasons.

  • Corrupt Windows Update components.
  • Conflict between third-party applications or external devices.

  Note If this occurs, it may take 30 minutes to undo changes, and then the system will display the Windows login screen.

  I suggest you try the procedure described in the article and check:

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates 

  Note:

  1. When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
  2. Please do not perform upgrade in-place or reinstalling Windows.
  3. After the boot minimum troubleshooting step, follow the "How to reset the computer to start as usual after a clean boot troubleshooting" section in the link provided to return the computer to a Normal startup mode.

  You may also see suggestions provided by Srimadhwa B responded on January 16, 2014 in the following link:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_update/failure-configuring-Windows-Update-reverting/07666a58-a9d7-45FA-bb61-4c7a43942680

  Please answer us on the State of the question to help you further.

• Windows Updates Setup error: "configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"stuck at 12%

  Just returned to windows 8, got my Norton security is and it.then update was of updates, so I can update to windows 8.1, but I got stuck when you try to update windows 8. It happened at 12%, and then tried to restart, it's 12% again.then what it says that windows does not not update reconfiguration do not turn off your computer.but I read someone post where they keyed off long the computer out the wireless USB mouse and took the card Sd, and the battery, put the battery back , but left the Sd Card and the mouse.and wireless USB, said, he started working.i tried all the this.and isn't yet working.it has been trying to run my computer hot.so I waited until what she calmed and it came again the same thing. ? Stuck in this mode.what do I do? I don't know if I should try just reset the computer of hole again or that it would be wrong.

  Original title: tried to update computers rose to 12%

  Hi Sandra,.

  Thanks for posting your query in Microsoft Community.

  You did it any significant hardware or change software on the computer before this problem?

  I understand that you can not install some updates with the error message "failure of configuration of the Windows updates...". ». I can imagine the disadvantages suffered by you and will certainly help you in the right direction to solve the problem.

  First place, according to the error message, I suggest you to try the steps in the following article and check if it helps.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  
  

  The question may arise if the Windows downloaded update packages are corrupt. So, if you are able to boot to the desktop with the help of the above article, I also suggest you try the following steps and check if the problem persists.

  Method 1:

  Try to run that Windows update utility provided in the following link.

  Problems with installing updates

  Try to install the updates after running the troubleshooter.

  If the problem persists, try the following method.

  Method 2:

  I suggest you to use Deployment Image Servicing and Management to fix Windows Update errors.

  (a) open an elevated command prompt. To do this, press the Windows key + Q and type in CMD right click on command prompt in the list and select run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  (b) type the following commands. Press enter after each command

  • DISM.exe / Online/Cleanup-image /Scanhealth
  • DISM.exe / Online/Cleanup-image /Restorehealth

  (c) close the command prompt, and then run Windows Update again.

  Check if the problem persists.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"- by a loop for hours, unable to get to the start

  Hello.

  First of all, I read this page - http://support.microsoft.com/kb/949358

  It says this - "Note if this problem occurs, it may take 30 minutes to undo changes, and then the system will display the login screen Windows.»

  But this is not true for me, I have nowhere near the logon screen. Earlier the PC rebooted, but is IMMEDIATELY returned to the exact same failure screen. There is a line.

  A few notes:

  (1) it is a G46VW mobile computer ASUS 'Republic of gamers ". I had 3 days. There is no DVD drive so I can't use any kind of boot disk.

  (2) I have no attached removable media.

  (3) I don't know how to get to any screen except that this form of failure, so do not know how to enter in a single command.

  (4) all that happens is that I see the ASUS logo, then this screen failure immediately.

  I'm panicking, it's all new. It has worked very well. I started it today, it has been updated slowly. I saw him at about 17%. Then I looked at a few hours later and saw that he was stuck in this process.

  What can I do?

  Hi James,

  I appreciate your patience and manual labor.

  You can follow the steps in the link below.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058/en-us

  Note: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. Follow these steps to resume and restore the registry.

  1. Go to Start creen and type regedit.
  2. Select regedit , then right-click on the screen.
  3. Click run as administrator.
  4. Right click on computer , then click export.
  5. In the Save in box, select the location where you want to save the backup copy to, and then type a name for the backup file in the file name box.
  6. Click Save.
  7. If something goes wrong, you can do a right click on the registry backup file and click on Merge.

  Write to us at the State of the question.

• Message loop "the configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer. »

  I had to edit this post, because I was the lack of information on my problem...

  Well that's even once...

  I decided to give maintenance to my laptop then I formatted last night then in the morning, I started today with the updates of windows (was the first thing I did, so I haven't installed programs). It started to download as 110 updates, when you're done, asked me to restart, and I did. As at other times, it configures the first 30% before restarting, and when it restarts then got stuck in the message of "Configuration of the Windows updates... failure. It takes like 20-30 minutes to restart, and when he does, still happens once, I mean the restart and the same message. So I can not connect or anything.

  Some features:
  Laptop: Toshiba Qosmio x 875
  Processor: Intel core i7-3630QM CPU 2 .40GHz
  RAM: 12 GB
  System: Windows 8 64-bit
  GPU: Nvidia GTX 670M / 3GB
  2 500 GB HARD drive, don't know the model or brand
  I have not yet installed antivirus, in fact I uninstalled Norton to install Kaspersky later, but I'm stuck with the real problem.
  I bought this laptop as 14 months ago, is the first time the problem appears.

  I have not tried certain steps of the links because some of them need to connect.

  Thank you, hope someone can help me.

  See this thread for assistance:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_update/failure-configuring-Windows-updates-reverting/9205aaba-BAfD-4760-8cae-26c82695136a

  Added: http://support.microsoft.com/kb/949358/en-us

  Perform a restore of the system (Windows 8, Windows 7 and Windows Vista)

• Default configuration of the windows updates. returning from changes. do not turn off your computer. (Infinite loop)

  Problem:

  • Computer: Lenovo N580
  • Windows 8
  • Reset my computer to factory reset
  • All my files uploaded to the computer
  • Launched about 120 windows updates
  • Now, the computer is stuck on the blue screen with the message that seems to never go "failed windows update Setup. returning from changes. do not turn off your computer"I can't access the login screen or any screen to disable the windows update.
  • I tried the solutions posted by other users with the same problem but without success.
  • Please help me with a solution where I don't have a factory reset because I don't have another copy of all my files!
  • Also, is there a way to access a safe mode on Windows 8? I tried F8 or SHIFT + F8 after starting, but nothing happens. I read a post online where Windows 8 have removed this feature. Is there another way?
  • Help, please! I AM ETERNALLY GRATEFUL!
  • THANKS IN ADVANCE!

  See: http://support2.microsoft.com/kb/949358/en-us (run a system restore)

  Perform the system restore from the recovery of Windows and check.

  (a) once you start your computer by using the Windows DVD or disc repair system, a black screen is displayed with the gray text "press any key to start from the CD or DVD. Press a button on any.

  (b) select the correct time and type keyboard.

  (c) click on repair your computer in the lower left corner.

  (d) select Troubleshooting in choose an option screen.

  (e) click Advanced options in the form of resolution of the problems.

  (f) select System Restore.

  Important: System Restore will return all system files not as documents, email, music, etc., to a previous state. These files of types are completely affected by the restoration of the system. If it was your intention with this tool to recover a deleted file to non-system, try using a file instead of system restore recovery program.

  Reference link:

  How to refresh, reset or restore your PC.
  http://Windows.Microsoft.com/en-in/Windows-8/restore-refresh-reset-PC

  If you don't have disc to install Windows or the system repair disc, contact the manufacturer of the computer.

  You can also refer to:

  How to create the installation media for a PC refresh or reset:
  http://Windows.Microsoft.com/en-us/Windows-8/create-reset-refresh-media

• Access to the Windows Update site 0x8024402C error code failed?

  Access to the Windows Update site 0x8024402C error code failed? Regds, 'a journey of a thousand miles begins with a first step."

  Resolution: 0x8024402C error Code

  Method 1: Remove the characters from the list of exceptions to the proxy and then clear the proxy cache to do this, follow these steps, as appropriate for the operating system that you are running. Windows 2000, Windows XP and Windows Server 2003

  1. Open Internet Explorer.
  2. On the Tools menu, click Internet Options.

     Note If the menu is not available in the Internet Explorer window, press the ALT on the keyboard to display the menu.

  3. Click the Connections tab and click LAN settings, and then click Advanced.
  4. Remove all the entries in the Exceptions section, and then click OK.
  5. Close Internet Explorer.
  6. Click Start, run, type cmd, and then click OK.
  7. Type the following commands. Press ENTER after each command.
     • proxycfg d
     • net stop wuauserv
     • net start wuauserv
  8. Try again to install updates.

  Windows Vista and Windows Server 2008

  1. Open Internet Explorer.
  2. On the Tools menu, click Internet Options.

     Note If the menu is not available in the Internet Explorer window, press the ALT on the keyboard to display the menu.

  3. On the Connections tab, click LAN settings, and then click Advanced.
  4. Remove all the entries in the Exceptions section, and then click OK.
  5. Close Internet Explorer.
  6. Click Start
     The collapse of this image enlarge this image

     

     , and then type cmd in the box start the search.

  7. In the list of search results, right-click on Cmd.exe, and then click Run as administrator.
     The collapse of this image enlarge this image

     

     If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  8. Type the following commands. Press ENTER after each command.
     • netsh winhttp reset proxy
     • net stop wuauserv
     • net start wuauserv
  9. Try again to install updates.
   

  Method 2: Enable the option "Automatically detect connection settings" in Internet Explorer to do this, follow these steps:

  1. Open Internet Explorer.
  2. On the Tools menu, click Internet Options.

     Note If the Tools menu is not available in Internet Explorer, press the ALT key to display the menu.

  3. On the Connections tab, click LAN settings.
  4. Click to select her automatically detect settings check box, and then click OK.
  5. Try to install updates again.

  Kind regards
  Sohail Patel Regds, 'a journey of a thousand miles begins with a first step."

• "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when trying to install Windows on Windows 8 updates

  Former title: windows 8

  Stuck into that and can't GET OUT! Failure of Windows updates. Restoration of the changes. Do not turn off your computer.

  Hello

  Please contact Microsoft Community.

  We understand the inconvenience that you are experiencing.

  1. How long it stays on the same screen?
  2. Windows Update is causing this issue?
  3. Have you tried to interrupt the installation at any time?

  When you try to install Windows updates, you get the following error: configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer. If this occurs, it may take 30 minutes to undo changes, and then the system will display the Windows login screen. Suggest you not to interrupt this until he completely undo these changes.

  Please see the article below and see if this can help you.

  https://support.Microsoft.com/en-us/KB/949358

  Let us know if you need assistance.

• "Configuration of the Windows updates failed. Restoration of the changes

  Configuration of the failure of the updates are happening all the time and takes a long time to restore updates. Please tell us how can I prevent automatic updates.

  To avoid failure, follow these steps:

  "Configuration of the Windows updates failed. Restoration of the changes

• Vista - during the Windows Update, get the error "computer restarted unexpectedly or encountered an unexpected error.

  While using the computer, a message appears that says a windows update had to be so I followed the instructions and started updating.  Courses through the computer restarted, then this window will appear.  I clicked 'OK' and the computer restarted again, but now only the loops with the same message.

  The computer works fine for the past several years and I have not tried to change the settings or the operating system.

  * original title - no error number. Message says: the computer restarted unexpectedly or encountered an unexpected error. Windows Setup cannot continue. to install Windows, click "OK" to restart the computer, and then restart extra

  While using the computer, a message appears that says a windows update had to be so I followed the instructions and started updating.  Courses through the computer restarted, then this window will appear.  I clicked 'OK' and the computer restarted again, but now only the loops with the same message.

  The computer works fine for the past several years and I have not tried to change the settings or the operating system.

  Hey dkeeney2330

  ·                        try a restore system before this

  http://www.windowsvistauserguide.com/system_restore.htm

  If necessary do in safe mode

  Windows Vista

  Using the F8 method:

  1. reboot your computer.

  2. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.

  3. Select theSafe Mode option with the arrow keys.

  4. pressenter on your keyboard to start mode without failure of Vista.

  5. when Windows starts, you will be at a typical logon screen. Connect to your computer and Vista goes into safe mode.

  6 do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that didn't he corrects not reposting in the windows update forum

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  Walter, the time zone traveller