Lose the connection to Windows 7 computer on a network, have to reboot several times a day to keep XP & Vista connected computers on it.

Similar Questions

• OfficeJet 6500 E709n series cannot be contacted over the network. Reinstalled, rebooted several times.

  Running Win 7/32 on two different computers HP laptop and updates on 2 iPhones and 2 iPad2s. I also have DirecTV whole House wireless set up through this network. The router is an E4200 of Cisco (Linksys), with the latest firmware and software updates, running Mixed Mode WPA2/WPA encryption.

  I installed, removed, rebooted and reinstalled the printer several times and do not see it, other than on the router's routing tables. I am unable to ping and can't see any (other than Cisco) software.

  I have tried to use the installation wizard 'automatic' in the menu of the printer #8, has made 'restore defaults', is 'advanced configuration', IP address and used auto and even with the SSID and key, I'm headed to an IP address that is not even close to be part of my network. I tried manual IP and combination of wireless configuration and put the IP address that shows on the Cisco Routing table. I tried "restore default settings", and then reinstalled the software after you have uninstalled and restarted everything. I tried HP Network Diagnostic Utility, and it can't find any problems on my network, another it does not find the printer.

  Nothing is allowing me to see the printer, except when I connect it via USB.

  Does anyone have any ideas where I can go for an answer?

  I found a solution validated by PrintDoc that worked:

  A static IP address is always a good idea for a printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you know what it is, set an IP address outside this range but not exceeding 254 (the last number of the address). If you don't know it, enter the current IP address.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the gateway and DNS white. Click on ' apply

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

  -instead of remake "Add a printer", I was able to change the properties of my current setup and add a new TCP/IP port, using the name of the computer, I had specified in the static DHCP entry in my router. Finally, it worked and I'm now able to print again from my laptop and the application of 'Print-N-Share' on my iPad and iPhone.

  Thanks PrintDoc! You got me most of the way and I managed to finish it.

• Have to reboot several times my Airport after the upgrade of the modem at Cisco DPQ3212

  Since the mobile phone cable modem and have installed by Cox, I found that my Airport stops working anywhere from 1 to 12 hours later. The telephony service is NOT disturbed. If I directly connect my MacBook Air to the cable-phone modem, I'm constantly on the line (3 days). Today, I was using the laptop for several hours and I found that I had to unplug the power of the a/c of the airport and reconnect four times since noon! According to the airport utility app, I have the latest version of the Firmware (7.7.3). Someone at - it suggestions?

  Thank you

  Henry

  Apple has released the Firmware for the airport 7.7.7. May be worth a try.

• I download CS5 and is 99% completed but is prompting the closure of the following applications: notification safaricloudhistory and safari. I have quit safari several times and cannot be found in preferences to close those apps! How can I fix?

  Have installed too many Yosemite... and always become familiar with Yosemite.

  Guest of installation of close SafariNotificati

  https://helpx.Adobe.com/Acrobat/KB/install-prompt-close-safarinotificati.html

• I renew the DHCP on my Airport Express Extender several times a day.

  I have a time Capsule airport connected to an ATT Uverse router mode bridge as my wifi router.  I have Airport Express 6 throughout the House using wifi Extender.  I have to renew the DHCP lease on a large number of Extenders several times a day to keep them in line.  I saw a few discussions online about this problem, but have not found a solution that works.  Anyone know the problem?

  I have a time Capsule airport connected to an ATT Uverse router mode bridge as my wifi router

  Does that mean that the Time Capsule is in Bridge Mode... or... does that mean that the ATT Uverse router is in Bridge Mode?

  Help if we understood what operating system you use the device that you use to administer airports.

• Windows 7 Home Premium 32-bit on a Dell Studio 140g running a NETGEAR WG111v2 54Mbps Wireless USB 2.0 adapt and loses the connection permanently

  I have a problem with this program-it very often loses the connection, so with any live video as a conference, he fall causing problems with, naturally, the frustration on both sides. The router is in another room may be just 25 feet away maximum which the signal passes through 1 wall and offered "free of charge to AT & T TV and Internet clients" so a technician said as saying "it's just a basic router", but the signal goes further to a TV, another 20-foot more away and had no problem connecting unless it is with the AT & T network itself. Even if he reconnects automatically most of the time, but sometimes I have to manually reconnect which can take of time also a lot of time. I had another SATA driver and separate, which was working fine then one day abruptly stopped and now that the driver to reconnect and I was forced to use the old and original driver and I'm back with the same problems. I can't find where it is that I found this other, independent driver, even with a search, and now I have no idea how to solve. I tried all suggestions with Microsoft Fix It without modification done or as it says "no changes have been made, your driver is up to date" and I have tried these suggestions and now I'm here. I also went to CNET to search for a driver, but not luck to everything I've read about the drivers there. Finally, I intend to go with another program called Easy Wifi Radar and I don't know what would be better to use Wifi adapter and since I have a few target (store) [s http://www.target.com/s?searchTerm=wifi+adapter & category = 9975894% 7CAll % 7Cmatchallpartial % 7Celectronics & lnk = snav_sbox_wifi + adapters] I guess I'll take the adapter on their part and their site search , I see a lot to choose gift cards, but who would work better with my system and this program of "Easy_WIFI_Radar"? Any suggestions? Maybe a better deal with another source of in-store/online Wifi adapter?

  Hi David,

  Thanks for posting on Microsoft Community.

  I understand that you have connected the external NETGEAR WG111v2 USB adapter to work with wireless internet and the connection is intermittent.

  Maybe it's because the wireless USB card driver and it is perhaps because of the hardware (USB wireless card) itself.

  Try the suggestions below and see if it helps.

  Method 1:

  You can try to download the latest Firmware utility from Netgear support site and check if it helps.

  Check out the link below to download the latest firmware for NETGEAR WG111v2.

  http://Downloadcenter.NETGEAR.com/en/product/wg111v2#searchresults

  Method 2:

  Dell Studio Hybrid D140G may come with the card wireless in the generation in it, you can try to disconnect the external USB NETGEAR WG111v2 adapter and try to connect to the network card wireless wireless generation.

  To connect to the wireless network, please visit the link below.

  http://Windows.Microsoft.com/en-in/Windows/view-connect-available-wireless-networks#1TC=Windows-7

  Method 3:

  Try disabling your antivirus software that may block the incoming connection wireless.

  NOTE: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Hope this information helps, please reply with the status of the issue for further assistance.

• Windows 7 workstation loses the connection with the Server 2008 "

  Server running Microsoft SBS 2008 Standard.  Second location is the use of Remote Desktop.  These workstations are very good.  Only the workstation in the same place loses the connection periodically.  Workstation can reconnect, but never know when it will drop.  The user has to go to the remote location to know that the work will not be interrupted.

  This particular configuration has worked very well for a few months.  Long story short about 2 weeks after main tech (which has implemented) is deceased in August 2010, there was a major issue.  No one is really sure of what it is, but everything is back up and running just now lovely annoying drop except for this connection.

  I'm scheduled to go on Tuesday.  This is a seasonal business and people we're patient but kind of necessity to deal with this finally.  I am pretty well convinced that this is not the Peachtree program causing the problem.  However, the error indicates that Peachtree is not installed on the server, and yet it is, obviously.  That is why we believe that the connection has been interrupted.

  All this makes sense?  Someone knows the effects of any automatic updates of end of August 2010, which may have caused a situation like this?  I know that currently they don't dare to update Java or something does not work well.  Thought, that you may know of something that happened at that time that could cause this.

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the Windows Server Forums on TechNet. Please post your question in the Windows Server Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Windows Server 2008 R2 gets really slow, loses the connection, network printers.

  I have a Windows Server 2008 R2, Dell PowerEdge T610 which very often at a time, it is really slow, loses the connection to all network printers and network resources are limited. We check scheduled task, updates of Windows and go on throughout this period. We check the event viewer, and there is nothing extraordinary. Does anyone have any ideas or suggestions?

  Hello

  Sorry for the inconvenience that you are experiencing.

  Since we are unable to help you better on the problems associated with Windows Server 2008 R2. Our TechNet team have the expertise to help guide you accordingly.

  That's why I ask you to please get in touch with our TechNet support team to resolve the issue.

  I appreciate your cooperation in this regard.

  Hope this will answer your query.

• HP envy laptop laptop 15-ah150na: loses the connection to the wireless network device I had not only portable for 2 days

  Loses the connection to the wireless network sometimes directly after that the computer is turned on at other times after 5 min and sometimes after an hour.  No other device I have loses the connection to the wireless network.  Help, please.

  Hello @fairgame,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I understand that you have a problem with the WiFi and wanted to help you!

  First of all, try to review the next steps, offered by community member @Great-Christine-Tree:

  First of all, we have a step by step guide to guide you through the process of diagnosis here:

  HP PC - troubleshooting Internet and wireless network

  A second option is to try the following steps:
  Powercycle the network:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.

  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.

  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.

  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.

  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.

  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down list in the upper right of the document.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• I lose the connection during the closing of the CMD

  Hi guys,.
  
  I configured a port for stand-alone listening as follows:
  
  C:\Program Files (x 86) \Java\jre6\bin > java-Dapex.home=D:\list-Dapex.images=C:\images-jar D:\apex.war
  Subsequently,.
  If I close the CMD, I lose the connection, and I have to reconfigure again.
  If I open APEX locally, I mean using the shortcut 'Get Started of Oracle Database 11 g Express Edition', then I lose the connection that uses the default port for the listener, it is 8080.
  
  After that I configured the listener that I got this message on the CMD
  
  -list properties-
  PropertyCheckInterval = 60
  ValidateConnection = true
  MinLimit = 1
  MaxLimit = 10
  InitialLimit = 3
  AbandonedConnectionTimeout = 900
  MaxStatementsLimit = 10
  InactivityTimeout = 1800
  MaxConnectionReuseCount = 1000
  Listener APEX version: 1.1.2.131.15.23
  The APEX listener server info: Grizzly/1.9.18-o
  May 21, 2011 17:14:41 com.sun.grizzly.Controller logVersion
  INFO: From Grizzly Framework 1.9.18 - o - Saturday May 21 17:14:41 GST 2011
  INFO: http://localhost: 8080/apex began.
  Using the JDBC driver: Oracle JDBC driver version: 11.2.0.2.0
  
  
  Kind regards

  Hello

  I don't know, I got your question right, but I'll try to find a solution anyway.

  If I close the CMD, I lose the connection, and I have to reconfigure again.

  This is what happens when a shell is complete - all related processes will be stopped as well. However, if you have an apex - config.xml in your apex.home you should not have to set up your listener APEX every time your departure, but it would be to reuse an existing configuration.

  If I open APEX locally, I mean using the shortcut 'Get Started of Oracle Database 11 g Express Edition', then I lose the connection that uses the default port for the listener, it is 8080.

  Now, if you have XE on the (local) computer running while you have your APEX listener running in stand-alone mode, you probably have a port conflict: by default, both APEX listener in stand-alone mode and built-in PL/SQL gateway (EPG) use port 8080. The EPG is enabled as a web server for APEX in XE after a new installation, the APEX listener would be an alternative in this case. You can stop the EPG, or reconfigure a server two web to use a different port, if you want them are parallel.
  To change the port used by the auditor of the APEX in stand-alone mode, you just add another parameter to the commissioning: -Dapex.port = 8888 and you're done.
  To change the port used by the EPG, connect as sys and run the following

  EXEC DBMS_XDB.SETHTTPPORT(8888);
  COMMIT;
  

  If you want to disable the EPG, simply on the port * 0 *.

  After that I configured the listener that I got this message on the CMD

  That's what it should look like.
  No, your subject is 'lose the connection when the CMD closing', I guess you're looking for an alternative solution. You can run the listener APEX as a Windows service, even in stand-alone mode. To do this, you create a batch file, for example

  %JAVA_HOME%\java -Dapex.home=D:\oracle\APEX_Listener\_home -Dapex.images=D:\oracle\apex_4_0_2\images -Dapex.port=8888 -jar D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\apex.war >>D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\my_apex_listener.log 2>&1
  

  Note that you will need to set JAVA_HOME as property system or replace the call with the absolute path to your JDK or make sure that the JDK is in your PATH variable.
  Of course, you can and should change the directories of other institutions to adapt to your system.
  Then, create a Windows service, for example [url https://iain.cx/src/nssm/] NSSM (free) or [url http://support.microsoft.com/kb/137890] SRVANY (MS, non-free), that starts your lot as a windows service.
  The order for the creation of this service using NSSM might look like the following

  nssm install APEX_Listener D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\startup.cmd
  

  You can subsequently change the service properties, for example to change the startup mode to "Automatic" to "On Demand.

  I hope that answers your question. If this isn't the case, please point me in the right direction.

  Thank you

  Udo

• Libretto U100 often loses the connection to the Wlan platform

  Hello

  I have a problem with my wireless network card. I often lose the connection with the hub. I read on another forum that it might be a good idea to update the drivers. I've never done this before and I want to make sure I do it correctly. Can you please let me know the exact steps?

  Thanks in advance.
  Kind regards

  Hello

  The update of the driver is not difficult. First of all to know what Wlan card you use! This can be checked in the device under network adapters Manager.
  Open the tree menu and check the card WiFi was installed.

  Then you check the Toshiba driver for the most recent updates page or visit the Wlan card manufacturing site to download the latest version of the Wlan driver.

  For the most part this driver package includes the setup.exe file. This file should be run. All that s. But if the setup.exe will fail then you could install or update the driver through Device Manager. There is an option that allows you to update the driver. You must choose the driver download source and the windows updates the old driver. All that s.

• OfficeJet 4620 loses the connection to the WLAN

  I have printer HP 4620 installed on my local wireless network.  I checked the Network Configuration page and the IP address and the gateway address are what they should be.  The router is a Centurylink C1000A.  I lose the connection to the printer.  If I have something to send to the printer it doe not prints.  If I unplug the printer and plug it into the time ' it prints what (what)  If I try again later I have to do the same.  This happens with all laptops and PC on the network.  Same thing if I try to scan.

  These settings are to set up your wireless printer stay connected to your router, keeps better connected wireless devices and makes your router secure and hack proof.

  1. position a static printer IP (see step 6) outside of the DHCP of the router Beach (check your manual).

  2. check the printer "Auto Off" is disabled.  Use the built-in webserver (EWS) by going in the

  the printers IP address in your browser's address bar, click Settings tab/Auto Off.  Or use the printer

  Assistant, printer Home Page (EWS).

  In the router: (refer to the manual of your router for more information)

  3. use a wireless channel fixed as 1, 6 or 11, never 'auto', try channel 1 first then the rest.

  4 choose the router to 20 Mhz only, or 145Mbps router function.

  5. always use WPA2-AES encryption (personal), but you can try the "mixed" mode

  6 disable the WPS and never use it and disable the UPnP for the security of routers.  No one can hack into your

  now the system and helps with wireless connectivity (if you want to know why, research on the web).

  7. If you have a router dual band (2.4 Ghz and 5.0 Ghz bands), make sure you the SSID is NOT the same.

  they must be different for all the bands, even for networks without comments.

  8. save all settings.  Food at the same time, wait 5 minutes.  Power on router wait 3 minutes.

  9. turn on the printer and check that it reconnects to the router.

  Windows 7/8/8.1 is discovered the system on or off?

  1. Control the network and Internet\Network and Center\Advanced share sharing settings.
  2. Under home or work (current profile)-network discovery.

  Select "Turn on network discovery" and save the changes.

• HP Office Jet Pro 8620: IMAC loses the connection to the printer

  Computer do not print and seems to lose the connection to the printer. I deleted all printers and made a new connection to the printer. Printer address 192.168.0.14.  IMAC later loses the connection to the printer again. I look at address on printer and now is 192.168.0.15. Its done this several times. So why the printer continue to change its address? Is it possible to put it permanently?

  Think I fixed it now. Problem was that I also had to set the Configuration of DNS address. Of course although computer knew the address of the printer, he could not find the server (i.e. the router) don't understand everything, but seems to work now.

  Went to the printer the webserver integrated with my Web browser. On the network, wireless 802.11, IPv4 configuration tab, I already had the manual IP, the subnet mask and the default gateway. I need to go to the next Section under the DNS Configuration, select "Manual DNS Server", then fill in the news for "Manual preferred DNS server".

  AllOf the above address were extracted from the information sheet, you can print directly from the front panel of the printer. My son who is more Apple savy than I am, said that he did not understand why I had to put an IP address manual for printer even when that she would have remained the same.  I don't either, but just know whenever IMAC my wife lost the connection to the printer IP address had changed.  My router is built with the Modem cable provided by the company. It is perhaps part of the problem.

  So no, it seems to be fixed number. So if you set a manual IP address, make sure that you also specify a "preferred DNS server"

  Thanks for your help

• lose the connection to the net after system restore

  I used the system restore and restart the pc after it but I lose the connection to net it gives zero transmission and recived it is a lock on the connection icon and when I try to use repair it gives the error message (windows could not finish repiring the problem because it is impossible to perform the folloing action not to conduct not query tcp/io of the canoe connection parameter)

  There is no problem with the connection that the net works with other PC not mine

  When first I used the net all the me I connect the Caron and its automatic execution

  so why it dosent run now the files make me lose the file how to fix

  When you did the system restore you have lost the connection to the network.

  Create a new connection

  Dale may

• Light (switch) on my screen does not turn off. I have to shut my computer down several times a day to turn off the monitor.

  Light (switch) on my screen does not turn off.  So, I shut down my computer and restart several times a day, because when I put it in mode 'sleep', he wakes to the top in a few minutes and will not fall asleep.  I could put a blanket on my screen when not in use, but I'd rather find a way to make it stay asleep when I tell him.

  Light (switch) had already done once before and I was so worried that once I turned off the monitor that I would never get it new on... a bit short of money here, to buy a new monitor, but the next day, I pressed the power button with an additional downward pressure and I could so he could start working again (able to turn the market monitor).  It was about 3 weeks ago.  Now, the light stays green, unless I stop the whole computer.

  Maybe my main problem is sleep mode, which removes the screen for like 2 minutes and then he wakes up to the top and is so rude when I myself and try to sleep, I just turn off the monitor everytime I put the computer to sleep.

  Now, I can't turn off the monitor, except by turning off the computer.

  Hi JDandGinger,

  I suggest you follow the provided article and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-power-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-monitor-and-video-card-problems

  If the problem still persists contact the manufacturer of the monitor for more help and information.