loss of palette, daq Assistant

Similar Questions

• Under VI 'DAQ Assistant': Sub VI is not executable

  Salvation OR engineer,

  My task is to acquire and record data of input voltage analog with PCI-MIO-16-1 and BNC-2110 connector. I can get the signal via MAX, but as soon as I drop down the function palette DAQ assistant in FASHION Lab blocks diagram, my run button becomes broken. I got the error message like "Sub VI"DAQ Assistant": Sub VI is not executable. How can I overcome this?

  Thank you

  Yvette.

  Hi Paul,.

  Unfortunately, SignalExpress is a different license than LabVIEW. However, you don't need a SignalExpress to acquire and record data. LabVIEW has every ability to SignalExpress and many more.

  Kind regards

• DAQ Assistant is not in LabView

  Hi all

  I use NEITHER cDAQ-9174 and NI 9203.  I have already installed the driver for the NI 9174 cDAQ, which is NEITHER-DAQmx 9.8.0.  I can see the device when I opened NI MAX. However, when I open LabView 2015, I can't find DAQ Assistant in the function Palette. I noticed on the chassis, 'ACTIVE' light is not on while two other "POWER" and "READY" light is on.  I look in the forums OR but I can not find the solution.

  Any suggestion, please help!

  Thank you!

  DAQmx 9.8 is not compatible with LabVIEW 2015.  You must use at least DAQmx 15.0.  See here for more details: NOR-DAQmx and LabVIEW compatibility

• Missing DAQ Assistant

  Hi guys,.

  I have LabVIEW 2015 and 14.0 DAQmx.

  Yet, the daq assistant is absent the express--> palette entry.

  Any help?

  Message 5 of this thread will give you the answer.  More precisely

  DAQmx and LabVIEW version compatibility

• Conversion task DAQ Assistant

  When I try to convert my DAQ Assistant tasks with a right click - Convert to task NOR-DAQmx I get a name and a scrolly input output with all the broken wires. Similarly, if I create a task in MAX and then use a constant for the task on the block diagram name I get the same result of entry scrolly. Am I missing a step here?

  Thank you

  Hi Mirabelle

  Glad to hear that you managed to solve the problem! In response to your questions:

  -L'information that read you about the creation of tasks in MAX is correct; It is possible to create a global task (an available screw a lot) in MAX. However, it is not necessary to create all of the tasks in MAX. As you think, if you use the task within a single VI, there is no need to create the task in MAX - in fact, it's probably easier just to create the task in the VI himself, either with screws of Express Assistant DAQ or DAQmx screw person on the range of functions located under e/s measurement > DAQmx - Data Acquisition.

  -When tasks change in MAX, it will not automatically be changed in LabVIEW. To make changes in LabVIEW, you will need to edit the task properties in LabVIEW, or remove the old task and replace it with the change.

  -I'm not sure what you mean by the question in your "P.S." to 100%, but I'll try my best to answer. Is there a specific example you speak? If you ask the use of screws DAQmx as DAQmx Virtual Channel Create, task control DAQmx and DAQmx Read etc., as shown in the examples of the expedition, then there are a few reasons to use those. Basically, screws of Express DAQ Assistant consist of a combination of the screw in the DAQmx - Acquisition of data from the function palette section. In general, screws of Express DAQ Assistant moving slower than the standard SIE DAQmx. It may be easier to debug the code when using standard screw, as it is obvious which task runs each section of the code. And finally, there are some limitations to the use of the DAQ Assistant, so while they may be easier to use in the short term, long term, I would recommend familiarize themselves with standard screws, because they make possible more complex tasks.

  I hope this helps! Feel free to let me know if you want to bring me anything, or if you have anything else that I can help you.

  Best regards

• Is the DAQ Assistant compatible with LabView7?

  I am equipped with a LabView7 and a NI DAQ - 6015 Pad and am trying to monitor the temperature with two thermocouples. I searched some tutorials online, but most suggest using assistant DAQ, which is not listed in the section of my functions palette entry. I have downloaded the NOR-most recent DAQmx driver who is supposed to be compatible with LabView 7.x. I don't know if this means that it is compatible with LabView 7.0. I still do not see the DAQ assistant appear.

  Any help or suggestion (about DAQ assistant or how to program in LabView7 to solve my problem) is greatly appreciated!

  Thank you.

  It looks like the DAQmx latest version is 8.1 which will work with LV 7.0

  See here http://digital.ni.com/public.nsf/allkb/97D574BB1D1EEC918625708100596848

• DAQ Assistant

  Hello

  I'm a new user for Labview.  I couldnot find DAQ Assistant.  Please suggest me some ideas to find out the same thing.

  or do I need connect my laptop to the material so that I will get the DAQ Assistant, in my software.

  Please help me

  Thank you

  Dembélé

  The DAQ Assistant is not installed with LabVIEW but with DAQmx. If you have installed the drivers for a DAQmx device, this will install the DAQ Assistant in LabVIEW. It is found on the measurement of e/s palettes > DAQmx - Data Acquisition.

• DAQ Assistant as input for the formula

  I need the output to my DAQ assistant for that entry into a knot of formula. But I can't do it because the terminals are different; data Dynamics vs double [64-bit real (precision ~ 15 digits)]. Is there a way in which I can use these dynamic data in a node form?

  Look in the express palette under the manipulation of signal for an another express VI, called "DDT".

• Impossible to find in LabView DAQ assistant

  Hello! I installed the driver NOR-DAQmax 9.3.5 after installing LabView 8.5 Student edition and I'm not able to find the DAQ Assistant, in the function palette. Could you please let me know what else I could do?

  Thank you!

  Hi cmorale4,

  Find this article in the DAQmx driver compatibility and LabVIEW, if you have the latest driver that you can install and use with LabVIEW 8.5 should be OR-DAQmx 9.3 you can find here.

  The best method is to remove all the drivers you have installed so far, you can do a registry clean with CCleaner and then proceed to the installation of version 9.3

  Kind regards

• 201003-error occurred in the DAQ Assistant

  Hello. I use "cDAQ-9178" and "NI 9215" and "NEITHER 9402" are added on. "

  However, when I run Labview code, "Error-201003" occurs.

  {

  Device not available. Possible causes:

  Device is no longer present in the system / device is not powered.

  Device is turned on, but was temporarily without electricity / device is damaged

  }

  (Error appears as the 1st and 2nd figures below).

  (Plans of logic is the figure below).

  Thank you.

  I could be something with the pilot

  Check this box:

  Error 201003 to the MAX test panel or all by running the DAQ Assistant

  http://digital.NI.com/public.nsf/allkb/5413F392D88326148625746B006745C5

  In this forum, they speak the same error:

  Spontaneous error code 201003 for acquisition of data PCI configuration

  http://forums.NI.com/T5/SignalExpress/spontaneous-error-code-201003-for-PCI-DAQ-Setup/TD-p/830707

• Control relay with Boolean switch using DAQ assistant 9481 - problems

  Sorry for what may be a stupid question but I'm stuck in quicksand.

  I use a relay module 9481 and have two external relays connected lines 0 and 1.

  When I create a digital output 0 line by line, I can run the test inside the express and activate the relay and turn off without problem.

  The generated block DAQ expressed expects a Boolean input of 1 d. (See attached photo).

  I want to connect a Boolean switch relay line disk 0. You can connect live not because the switch is Boolean and the input is Boolean 1 d - I'm a conversation in the pict.

  All plumbing lines display results, the relay never active.

  Any bunch would be greatly appreciated! Thank you

  

  Mr._Mechanical,

  Welcome to the Forums of switch OR this forum is generally intended for products OR-SWITCH [such as the NI PXI-25xx & NI SCXI-11xx], I think I know the answer to your question.

  I think the reason why it's a failure is the conversion you make generates a table of 16 Boolean [as the 'boolean to (0,1)' function creates a data I16 type] with your data more false data points 15.

  

  When you try to control the relay, he sees 16 datapoints are you Commander to a single port [channel] and so error out.

  

  My suggestion would be to use normal DAQmx digital output screw [with, he set up as ' Digital > single channel > single sample > Boolean (1 line) "] rather than the DAQ assistant.

  If you use the daq assistant, simply by using the function 'Building the table' will transform your simple Boolean data point in a Boolean array containing a single element.

  

  While the DAQ assistant is very easy to use, I recommend that you use the DAQ assistant, because this reduces the features and increases the execution time.

• Simulate signals wired to the DAQ assistant for USB-6009 device

  Hello

  I'm trying to send a signal to the DAQ Assistant Express VI.  I watched the movie "Generating a Signal" on the Web site of NOR (www.ni.com/academic/students/learnlabview/generate.htm) and I have my Signal simulate connected directly on the DAQ Assistant, as shown in this film.  In my case, the DAQ Assistant sends the signal to a device USB-6009.

  However, I received this message:

  Error-200077 occurred to the DAQ Assistant
  Possible reasons:

  Requested value is not supported for this property value. The value of the property may be invalid because it is in conflict with another property.

  Property: SampTimingType
  asked the value: Sample clock
  You select: On-demand

  If I select 'On Demand' in my DAQ assistant and run the vi everything works beautifully.  However, I need my DAQ assistant to be configured to generate a waveform AC continuous, not output a single alternating current rippling.

  What happens here?  I did not have this problem before on other devices of NOR. I am using LABView 2010.

  Please answer.

  Thank you.

  double post

• Multiple entries to the DAQ Assistant

  Hello

  I'm doing my DAQ Assistant, in several (formed of an array) Boolean inputs where there is 1 digital output. (see attached software folder)

  Physically, I want a valve to open and close at a certain pace, where the user can install/control this pattern until the program starts.

  I think that the best way to do it is to have multiple Boolean values that the user can press or unpress.

  Before that, I started, I tried with only Boolean 1 where it worked perfectly.

  As seen on the attachment (error), it is possible to an easy problem to solve, but I just can't figure it out, I'm stuck at my already made solution.

  I use USB6008.

  I hope that there is a gentle soul who can help out me.

  Best regards

  Kenneth G. Vejen

  Hi Kenneth.

  When the output to the generation mode is set to "sample 1", which means that whenever you call the DAQ Assistant will generate 1 sample. In order to generate 5 samples, you must therefore call 5 times.

  I have attached a modified version of your VI, which shows a way to archive it. However, be aware that the samples will be generated fast and not at 100 ms note your loop runs. It depends on your application, if it is as you want samples to be issued.

• Calibration of thermocouples in the DAQ Assistant, using data from spreadsheet?

  Hi all

  For my first application LabVIEW, I'm looking to automate the calibration of thermocouples by measuring their response at different temperatures in a dry well Sizer. I get temperatures of thermocouples six by SCXI 1303/1102/1600 and have six channels put in place in one of my subVIs in the DAQ assistant.

  I compare these values to temperature calibrator that I am acquiring by VISA series in an other Subvi. All these values are written in a .csv file.

  Can I import these data into the DAQ Assistant to use for calibration? Is there a simpler way to associate with the channel calibration data? Currently, I could manually copy - paste the cells on the worksheet in the calibration sheet, but that seems just silly.

  If there is everything that I could provide to help solve the problem, let me know!

  Thank you!

  Hi Zoysiamo,

  It is possible to automate the calibration screws DAQmx at a lower level, in particular the DAQmx channel property node. Using you can specify advance nationwide and the values on the scale for your channel. I recommend you take a look at this example of the community. The property node configuration will be similar to, as illustrated below:

  

• DAQ Assistant stopped working

  Hi all

  I have labview 8.6 installed on my laptop. currently of the problems with the DAQ assistant. When it initializes the host of assistant OR no longer works and an unknown error message is given. Don't know where to get corrupted files etc my daq is a usb-6008 and my laptop is running windows vista. I think that the issue is to do with a driver in the folder of Max but I don't have enough experience with her. I currently install OR-DAQmx 9.0.2 in the hope it will solve the problem. any help on this would be greatly appreciated.

  Kind regards

  Jason

  Hello jpraffer,

  Install the DAQmx helped 9.0.2 or you're always to see the current issue.

  Kind regards

  Philippe