Management port
We have an ASA 5510 at the remote office. There is no network administrator at this place. The network administrator of connections of office from the hand to the Cisco VPN client to do Administration on the SAA. What IP address you EF in the management of the ASA port? Would you leave it by default 192.168.1.1?
Thank you.
Laura
Assuming that there is LAN - to - LAN VPN tunnel between the remote control and HQ, you can manage using inside the ip address of the ASA remote.
When you customer VPN to your seat, you are able to access your remote LAN? If you can't, then you need to configure a few things regarding the VPN itself:
(1) for the Client VPN Split tunnel should include the Remote LAN subnet
(2) crypto ACL for LAN-to-LAN tunnel between the main office and remote must include the subnet pool of client vpn as interesting traffic, that is to say:
On the main site: ip access list allow
On the remote site: ip access list allow
(3) on the remote site: management-access within the--> to manage the inside interface via the vpn tunnel
(4) on the remote site: NAT exemption must include the Remote LAN traffic to the pool ip vpn subnet.
(5) on the remote site: If you manage via SSH or ASDM, you would need to include 'ssh inside', or 'http inside. "
(6) on the main site: same-security-traffic permit intra - interface---> to allow for you-turn vpn client traffic to the tunnel of lan-to-lan at remote site.
Hope that helps.
Tags: Cisco Security
Similar Questions
-
About 4500 X VSS question management port
I have two switches of 4500 autonomous X that I intend to convert vs. If I cable to the management port on the two switches for a cloud of management, what management port should be the IP address of management? It is the active switch port? If the active switch failed, the management of the standby switch port would resume the IP management?
The management port is VRF mgmtVrf. Should I create a default for the VRF route ' ip route vrf mgmtvrf 0.0.0.0 0.0.0.0... ' to point to the IP Address of the default gateway?
Thank you
When you convert the VSS chassis, only the interfaces of management (FastEthernet1) for switch-1 (active) will be visible in the config. If you want both your cable management cloud management interfaces, but you apply only the IP address to the active switch.
The management port is VRF mgmtVrf. Should I create a default for the VRF route ' ip route vrf mgmtvrf 0.0.0.0 0.0.0.0... ' to point to the IP Address of the default gateway?
OK, you need a default route in the vrf mgmt pointing to the bridge.
HTH
-
HP DL380p G8 - packets ignored on the management port but not the virtual computer.
I searched through discussions, but not found a request for my problem.
We have added two new guest VM in the center of the customer data. Currently, they had 2 x DL380 of the G7 which worked perfectly for 2 years. We have added two new DL380p G8 and have some weird dropouts on the management ports. Currently using SAS-store data (no SAN or iSCSI)
I have pre configured servers (2008 R2 on each single guest) before their move in the data center using ESXi 5.0.2 http://h18004.www1.hp.com/products/servers/software/vmware/esxi-image.html HP installation. Since we moved to the datacenter, however, the new servers to experience about 10% loss/fall of package to the management port IP, but 0 packet loss on the IP comments. It doesn't make a difference either if the management port and the vswitch are on separate NIC interfaces, same result when combined on the same network adapter.
The Guest VM seem to work well and are not affected by the present, but any P2V we are trying to do currently fail due to loss of packets on the management port.
Other host (DL380 G7) servers running the HP exsi distro 5.0.0 and don't suffer these questions.
Any advice would be appreciated. I wanted going 5.1 because when I was configuring initially I wasn't aware that there was an application of conversion of VMware for him - it seems now exists, so if you think 5.1 is the answer, then I'm happy to go ahead and do it.
I solved this problem, but thanks for all the help...
Note for all the other people there. If you clone an esxi installation SD or USB or else save time, the MAC addresses of the server of origin met on the new server, regardless of the different physical MAC address.
To resolve I had to run esxcfg-advcfg - s 1/Net/FollowHardwareMac on the server that had double MAC address list. All the VMnic (4) in both servers had the same Mac as well just change the port not fix her. A new card would have solved my problem, but does not solve the problem.
The problem was discovered running by displaying the ARP table.
-
Traffic on the management ports load
Can someone tell me what traffic is running on the management port? I install vsphere 5.1 with 3 hosts, vmotion and san iscsi drive. I intend to separate management traffic on a closed network of 1 GB in which the management ports will connect to a 1 GB switch which will have a port connected to the global network. Use VMotion cela this port strongly with its activities?
The cluster will be slightly loaded with only 8 to 10 vm across all 3 four hosts of Quad Core processor.
I intend to connect with NICs 10Gb iscsi san and dedicated switch.
If I had to, I could use a 10G switch to the management network.
The individual virtual machine will be nic interfaces 1 Gb individual key of the network if necessary.
If you could tell me the documents that would also be appreceiated.
any thoughts would be appreciated.
Thank you
Ken
"Best Practice" is said to have a network card dedicated to the management, and a dedicated for vmotion. Ideally different subnets / VLAN.
In smaller environments, but I often will create this:
vSwitch0 with 2 network cards (if everything goes well on the cards separated/asics) and with the management and vmotion vmkernel port. It works very well, thank you very much despite sometimes described as not "best practices." Well - I think that the concern is that in situations of heavy vmotion (especially when storage vmotion is concerned) traffic management could be hampered/flooded. I just never saw him in the real world, although in environments with more than 4-5 guests I always put in place in accordance with the "best practices" just because...
vswitch 1 with 2 maps, 2 vmkernel ports (each with its own ip address) for iSCSI
vswitch 2 with 2 (or more) network cards and however many ports of VM / VLANS are necessary.
(just to be clear, the 'best practice' would vswitch 0 with 2 network cards and 2 vmkernel ports that configured in the management and the other as vmotion.) Each nic will be dedicated to a vmkernel, but available failover for others...)
-
ESX 4.1 management port
Hello
I have 1 NIC and my host network interface was working on IP 192.168.10.1 and is the network management from the beginning, when I installed VMware ESX 4.1, when I change the management port to the vlan 1 is not accessible all the network connection are OK when I'm trying to ping from the same subnet, it does not ping. Even though when I plug directly into a laptop ESX hostby is not ping, NOW what are the steps I need to take to recover the host.
Thank you
You must activate shell access through the console of the ESXi host - instructions can be found in this doc - http://pubs.vmware.com/vsphere-50/topic/com.vmware.ICbase/PDF/vsphere-esxi-vcenter-server-50-command-line-interface-getting-started-guide.pdf - once you remove the tag of vlan of the vwitch - http://pubs.vmware.com/vsphere-50/topic/com.vmware.ICbase/PDF/vsphere-esxi-vcenter-server-50-command-line-interface-solutions-and-examples-guide.pdf
Or you can change the physical switch and add the id vlan to the port.
-
How do the 4000th Equallogic Installer management ports
Hello
We released Equallogic 4000E with two controllers. I would like to connect the management ports on our "management VLANs" society.
But I don't know if I need two different IP addresses for the two management ports?
Or I just organize just one IP address for one of the ports management and EQL will take care of the rest? I understand that a single controller is active at a time.
Appreciate any clarification on this if you have storage EQL.
Thank you
But what I don't understand is the number of IP addresses do I organize for the "management interface."
1 single IP on your network.
The standby controller will have all the IP when it become active (and the other become Eve).
André
-
ESXi 3.5 - Management Port now a Vmkernel Port
I built my first box of ESXi 3.5. Wow I love the installation. Had a working server complete in less than 15 min from start at once, as it was in the CR 2.5. After installation, I noticed when I went to add a new vswitch so that at the end of the wizzard I wasn't able to create a port vmkernel on the same subnet as an another port of vmotion vmkernel. I watched one noticed that vswif (vswitch0) did not have a console port. The management port has been merged/rolls in a way vmkernel. I checked a TI has the ability to make a port of vmotion.
My question is... Is this OK or best practice or not a good idea to use the vswitch hosting the management port to get the vmotion traffic using ESXi?
Pete
Hello
Transferred to ESXi forum.
My question is... Is this OK or best practice or not a good idea to use the vswitch hosting the management port to get the vmotion traffic using ESXi?
I would treat the management port just like you would treat any network management, keep it separate. However, most people combine VMotion and management on the same vSwitch. In general from a security perspective, the management is separated from VMotion. VMotion is a clear text Protocol, so access to it should be restricted to JUST ESX hosts.
If it was me, I create an another vmkernel for VMotion on a different subnet, and give it it's own Teddy.
Best regards
Edward L. Haletky
VMware communities user moderator
====
Author of the book "VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.»
Blue gears and SearchVMware Pro Articles: http://www.astroarch.com/wiki/index.php/Blog_Roll
Security Virtualization top of page links: http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links
-
WLC management port is another trunk that vlan native
Hello
I installed my first WLC 5508 with this topology:
WLC connected trought distribution SFP 1 GB port to the port of switch configured as a Trunk port cut 3 Wireless VLAN:
-Management WLC, wireless and wireless voice data Vlan (Vlan native is WLAN Management).
-J' created 2 dynamic interface on WLC on my VLAN Wireless:
10.7.1.0/24: default management Virtual Interface installing WLC +.
10.7.6.0/24: Virtual Interface of voice and
10.7.2.0/24: Wireless Data Interface virtual trought GUI.
DHCP configured on each dynamic interface is the interface vlan L3 subent for SWITCH main technical IP DHCP Pool equal VLAN.
WLC management interface IP address is: 10.7.1.10/24
I create 2 WLAN SSID name with given ID 1, and ID2 voice.
I create and AP group named APGRP1 that contains the AP recorded about WLC and using the two WLAN SSID.
The two AP are connected to the switch acess port configured as native management WLC VLAN access port.
I have to create 3 IP DHCP pool on main switch with the related L3 Interfaces for Inter VLAN routing.
Problem: when I try to connect from mobile data SSID I get IP address of management WLC VLAN a VLAN data no.
the same case of Wireless IP Phone configured with voice SSID.
What I can likely that allows two devices to get the address IP of the correct VLAN?
Thnks
Hi Adil,
T1 > coelio AP on the switch must be configured on a mode of access to the port or trunk mode?
YEARS - the LWAPP / CAPWAP APs connected to the switchport should be an access port not trunk.
Q2 > if the first case, the configuration of the port, on the same VLAN as WLC management VLAN support Vlans other WLANS (voice and data)?
YEARS - Yes it supports, since traffic that involes the WLAN will be inside the tunnel of logic LWAPP/CAPWAP.
Q3 > I will check the interface between WLAN and dynamic Interfaces map and I'll tell you.
YEARS - I will wait for your answer!
Let me know if that answers your question...
Concerning
Surendra
====
Please do not forget to note positions that answered your question and mark as answer or was useful -
Hi guys,.
I met again a problem with the new virtual device of Cisco first LMS 4.1.
My camera is installed, built-in license and several features added in the DCR.
If I go the inventory > manage device state, I can find ALL of my additional devices (I use the host name, without adding DNS domain).
But in the Campus Manager , for example in: Configuration > Workflows > VLAN > Vlan Port trust , I have not all devices!
Well, I tried several times to launch a Collection of data on "All devices", but nothing more...
If I go to Admin > Collection settings > Data Collection--> display devices --> always the same features inside... nearly 20 devices and I have a lot more than 20 devices in my network!
How could I solve this problem please?
It's really annoying, because we can't TRUST VLAN PORT of LMS on devices...
Thanks a lot for your answer.
Kind regards
Stéphane.
When the devices do not receive "data" they will display just not there
Nothing under the field selector (VTP) is then?
Do not know what could cause this. In my opinion, a problem with the db of ani.
You can reset or make a dbrestoreorig. See the documents of the forum for more details
See you soon,.
Michel
-
I would like to add additional management port with different user service
Hello
Version of the grid control is 10.2.0.1.0.
My company has now more than 100 target or with teams of Directors access to the WHO,
The original grid for us infrastructure is 1 WHO + 1 OMR. WHO answers very slowly recently.
Now we decide to add additional management service in another machine.
The user to operate the original SGD is different from WHO come, it will be a problem when you configure the new OMS?
The other issue is, we want to use different ports (11200) for the new OMS, it is practical, if OK, how?
Thank you very much.
The user to operate the original SGD is different from WHO come, it will be a problem when you configure the new OMS?
OK, you can choose any username, any username to install additional management service in another machine.
It has nothing to do with the configuration of the original WHO. They remain in the 2 totally different machine. SST and their, OC4J OracleAS Web Cache
operate independently.
The other issue is, we want to use different ports (11200) for the new OMS, it is practical, if OK, how?
Thank you very much.
It comes fully documented standard:
Oracle.sysman.top.OMS:s_staticPorts=/home/Oracle/MyPort.txt $ / Disk1/runInstaller
The content of /home/oracle/myport.txt may as follows:
Oracle = 11199 Server HTTP port
Oracle HTTP = 11200 server listening port
Oracle HTTP = 4443 Server SSL port
Listening port of the server (SSL) Oracle HTTP = 4445
Oracle HTTP Server Jserv 8007 = port
Server diagnosis Oracle HTTP = 7200 port
Oracle = 1830 Management Agent port
Application Server Control RMI = 1850 port
Notification Server Oracle application port = 6003
The Notification Server Local port Oracle = 6100
Notification Server Oracle 6200 = Remote port
Connect the port Loader = 44000
Cache of objects Java port = 7010
Port of DCM Java object Cache = 7101
Port control application server = 1810
Web Cache HTTP port listening = 11199
To listen Cache HTTP Web site (SSL) port = 4443
Cache Administration Web site port = 4000
Website of the Cache Invalidation port = 4001
Cache statistics port Web site = 4002
Oracle Net Listener = 1521
Management Service Upload (non - SSL) = 11199 Oracle port
Management Oracle Upload (SSL) Port = 11198
-
Is it better to have all of your VMKernel ports on the same subnet or subnets separate (one for each role, iSCSI, management, vMotion, FT)? Are their potential problems with either scenario? Please include the ESX and ESXi. I want to get my setup just as it should. Please let me know also if you need additional information.
I have licenses for ESX and ESXi, but I'm leaning toward ESXi are all vSphere 4 Update 1.
Hello
In fact, you have to use separate subnets for your vmkernel ports but they can run on the same thread. You can share a subnet between a vmkernel and service console, but not between two vmkernels. Just like that. So yes, you need to use several subnets.
Best regards
Edward L. Haletky VMware communities user moderator, VMware vExpert 2009Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]
Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]
Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]
Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]
-
Management for EqualLogic failover port
I'm setting up a Dell EqualLogic PS6210XV.
I configured dedicated management interface. When I disconnect the management on the active controller port, it is not automatically switch to the management port on the controller to start (as a port 10 GB of data). Please guide me how to do this fail over automatically.Hello
There is no automatic failover with dedicated Mgmt ports. You will need to either restore a connectivity or a failover on the other controller.
Kind regards
Don
-
There is a security risk to plug the internet router management on the LAN port?
I have to install an ASR1001 on the internet for my business. I noticed that the ASR1001 has a dedicated management port and I was wondering if it's a security risk to have this mangment port directly connected to my local network, so that I can mange it from my office.
I want to only run the ASR of this port and I will no management through its public IP address. Is it possible for a malicious user to compromise the router then have access to the network but this management port?
I'd say it's a reasonable risk. If you intend not to allow future management of the public side sessions you are a good start, implementation of protection against attacks. Combine that with a few basic hardening, for example to disable source routing, directed broadcast, ip proxy arp, finger, as well as an ACL on the management interface so that all traffic from an untrusted interface on the router would be unable to receive return traffic. In addition, the management vlan must be a dedicated vlan. I would not fall in the same vlan in that your office is located. Better design would be to fall into a dmz (acl on the router's management interface would be redundant in this case) and to apply the rules of the firewall. However, if this is not possible, order access to routing on the ASR as well by including only a 32 road to your management station via the management VLAN interface. Also, remove any redisribution or advertising of this management interface in your routing protocol.
-
port management and control for nm-cids
Any body can help me to find the difference between the ip address we use to ID-sensore 1/0 interface and ip address of the sensor and its default gateway
10.10.10.2/24,10.10.10.1
JOINT-2 information.
There are 8 interfaces of interest when it comes to the JOINT-2.
4 If the interfaces belong to the JOINT-2 itself.
4 other interfaces are the switch ports connected to these 4 JOINT-2 interfaces.
The management of the JOINT-2 interface is ' GigabitEthernet0/2 '.
When you assign an IP to the JOINT-2 is the interface where the IP address is assigned.
On the backplane of the switch it will connect to a corresponding switch port.
In the BONE of cat is "/ 2", and in the IOS is the "management-port intrusion detection module.
These switch ports must be assigned to what ever vlan door network address assigned to the interface JOINT-2 s Gig0/2.
The ' GigabitEthernet0/7 and GigabitEthernet0/8' JOINT-2 are the JOINT-2 control interfaces and must be assigned to the AnalysisEngine for surveillance.
On the backplane of the switch they will connect to 2 corresponding switch ports.
In the BONE of cat, they are "/ 7" and "/ 8", in IOS, they are "detection module of intrusion-modem 1" and "data-port 2". ""
You will need to set these ports as capture ports if follow on promiscuity, OR vlan unique ports (access-ports) if making pair interface online monitoring or ports of junction If inline vlan pair followed to do.
"GigabitEthernet0/1" of the JOINT-2 is not configurable on JOINT-2 and is used only for sending TCP resets in promiscuous mode.
On the backplane of the switch it will connect to a corresponding switch port.
In the BONE of cat is "/ 1 ' and should be left a trunk port routing all the VLANS. In IOS this port is not considered in the configuration that the user never needs to change the configuration of this port.
There are also 3 to 6 ports that are visible in the BONE of cat. But none of these 4 ports are connected to anything on the JOINT-2 module itself and can be ignored safely. These ports are not at all in IOS.
-
Firefox automatically adds the port number in the address bar when it is not.
I work for an ISP company that implements regular routers for a customer locations. One of the things I need to change about it is to assign the management port 8080. For example, 192.168.0.1:8080. Once I try to install a new router that Firefox automatically assume I want to go to the same port 8080 and automatically concludes for me. Since the new router has not been configured with the 8080, yet I can't. So basically I would like to see if I can stop Firefox automatically enter this bit of information. It is very annoying and even more annoying that I have to use another browser to make changes since Firefox can not. I found a similar fix posted when Firefox will automatically ".www" but which did not fix my problem.
Disable the URL bar auto-complete feature. You can always select an address already used by the arrows down on the drop-down list of AutoComplete, but Firefox won't add characters to the URL as you type. Here's how:
(1) in a new tab, type or paste Subject: config in the address bar and press ENTER. Click on the button promising to be careful.
(2) in the search box that appears above the list, type or paste the filling and make a break while the list is filtered
(3) double-click the browser.urlbar.autoFill preference to change its value from true to false.
Who help me?
Maybe you are looking for
-
I have two companies for which I connect to an Internet site for the data. I clicked "remember me" for the first company and now I can't get to the home page to open a session for the 2nd, he just guard logging in for the first.
-
How to type letters accented with Satellite L300D?
I recently bought a Satellite L300D laptop and I need to be able to type in foreign languages. On standard keyboards I use the Alt key as the numeric keypad to achieve, but I can't understand how this works on this laptop (holding Fn and Alt don't wo
-
Satellite L30-114 - 2 GB of RAM does not work
Hello When I put 2 Rams 1 GB each my computer do blue screen and restarts, but on one of this computer of Rams two work without problem. A friend told me to update the chipset, the problem is that I can't find for this model of laptop
-
Question about Satellite L40 - 14 G and Vista drivers
I have Satellite L40 - 14G with Korean Vista installed and I have created a form of system restore DVD. If I have installed Vista English verson, can I installedDrivers of this DVD I created recovery.
-
Change the size of the layout of winmail panels
I have a preview on the pane of the header pane. I often move the line of demarcation between these lines upwards or downwards. About 80% of the time the mouse won't jump the line to move. I never had this problem with outlook express and I don't hav