Material of restoration to the original state of the manufacturer will make legitimate recovery discs work?

Similar Questions

• If I want to sell my iPhone, and I restore it, the buyer will never know that I had initialized before?

  If I want to sell my iPhone, and I restore it, the buyer will never know that I had initialized before?

  It will be clean, if you go to settings > reset > erase content and settings

• Re: How to recover the Equium A210 - is not recovery disc

  How can I do to make a recovery for my A210 (PSAFJE-003003KS) disc, according to pc world it should came with a disc, but it didn t, and although there is a hard disk I would like to have a physical that my laptop is upward lately.

  Hello

  I think that your laptop supports HARD drive recovery!
  Therefore, it should be possible to perform the recovery procedure, without the use of the Toshiba Recovery disk.

  Just press the F8 key immediately after the laptop has been turned on.
  Then choose fix my computer-> new window should open.
  There, you have to choose the last option called Toshiba Recovery and follow the instructions on the screen.

  Please note that this procedure will fix the laptop back to the factory settings and format the entire HARD drive!

  Concerning

• Is the standard Satellite A200 product recovery disc?

  It is very regrettable that after reinstalling the product of my Satellite A200 recovery disc, the language is now in Deutsch. Since I got the recovery disc to the center of Toshiba for a replacement, do you not thank they will be replaced by an English version? If so will be affect the entire notebook in its performance, or perhaps a program previously connected may have disappeared or missing.

  The product recovery disc is standard for the same unit of model because there is that no product key required?

  SP1 = Service Pack 1. This package has been designed by Microsoft and contains all useful and patches hotfixes. All this is designed to repair the operating system and make it better and safer to be used again.

  At this time you should not install SP1. It may happen that some problems may occur after the installation of SP1. Toshiba didn't start load SP1.

• in the Windows 7 32/64 recovery disc

  Please have tried to use the obtained drive as well as from the command prompt and typed in Chkds/F/R.then readings. The type of file system is NTFS. Windows cannot run disk checking on this volume, because it is write protected. Any suggestions please

  Thank you to l then put in the ERD? Please, I'm not very good at this CONSIDERED MICHAEL

  Unless prompted, this particular task must exempt from the need to provide a good recovery disc.

• Recovery discs works on another computer of the same model?

  Hello! I traded recently one laptop for another of the same model and I was wondering if the recovery discs for the preceding her work or do I have to do another series.
  It's the computer, to which I was referring:

  HP Pavilion 15.6 "laptop with AMD A8 Processor - 3500M (DV6 - 6188CA)

  Thank you!

  May

  Since it is the same model, they will work.

• My computer has a virus. I took it to Staples and they restored to its original state, however, I don't have Word, Excel, PowerPoint, or Publisher. How can I get these programs on my computer?

  Microsoft Windows XP Home edition Service Pack 3, Microsoft Windows XP, Microsoft Office Small Business Edition 2003, information Windows, Cyberlink PowerDVD and Sonic Record now, dell Service Tag

  Reinstall the missing programs from the original disks. Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA

• __Computer still crashes after restoring to the manufacturing of image... _

  Hello, could someone help me with these problems that I have been.  To be more precise... I have just restored my computer to the image of the original and always after the update of all my undates my computer crashed after that I logged.  These are the problems after isent problems and go...

  Signature of the problem

  Problem event name: BlueScreen

  The system version: 6.0.6001.2.1.0.768.3

  Locale ID: 1033

  Files helping to describe the problem (some files may be is no longer available)

  Mini092410 - 01.dmp

  SysData. XML

  Version.txt

  See a temporary copy of these files

  Caution:

  If a virus or other security threat caused the problem, open a copy of file can harm your computer.

  Additional information about the problem

  BCCode: a

  BCP1: 0000000000000880

  BCP2: 000000000000000C

  BCP3: 0000000000000001

  BCP4: FFFFF80001A329A5

  OS version: 6_0_6001

  Service Pack: 1_0

  Product: 768_1

  Information about the server: 8be216f4-46dd-404e-be57-15ec5ada3372

  Signature of the problem

  Problem event name: MpTelemetry

  Signature of the problem 01: 8024402C

  Signature of the problem 02: EndSearch

  Signature of the problem 03: search

  Signature of the problem 04: 1.1.1600.0

  Signature of the problem 05: MpSigDwn.dll

  Signature of the 06 problem: 1.1.1600.0

  Signature of the problem 07: Windows Defender

  The system version: 6.0.6001.2.1.0.768.3

  Locale ID: 1033

  Additional information about the problem

  Bucket ID: 31295353

  Problem event name: MpTelemetry

  Signature of the problem 01: 8024402C

  Signature of the problem 02: EndSearch

  Signature of the problem 03: search

  Signature of the problem 04: 1.1.1600.0

  Signature of the problem 05: MpSigDwn.dll

  Signature of the 06 problem: 1.1.1600.0

  Signature of the problem 07: Windows Defender

  The system version: 6.0.6001.2.1.0.768.3

  Locale ID: 1033

   

  Q: do you have a Norton or McAfee free trial come preinstalled on the computer when you bought it (and that would have been installed, but not valid, when you reinstalled Vista)?

  A: McAfee has been the free trial when I bought the laptop.  I've tended after the expiration on the McAfee.

  Comment: If you didn't let the McAfee free trial expires before replace you it with the application of Trend Micro, chances are that you should not have to reinstall Vista.

  When you reinstalled Vista, McAfee free trial was also reinstalled, but not valid. You should have (1) uninstalled McAfee free trial AND (2) download / run the McAfee removal tool (see below) before installing Microsoft Security Essentials AND BEFORE that you have installed the Windows updates.

  That being said, see if the following solves your problem:

  1. download the McAfee Consumer Product Removal, save it to your desktop tool:http://download.mcafee.com/products/licensed/cust_support_patches/MCPR.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. click right on the file saved in #1 above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

  4. open Internet Explorer (only) to http://support.microsoft.com/kb/923737 & run the difficulty.

  5. open Internet Explorer (only) to http://support.microsoft.com/kb/971058 & run this difficulty in DEFAULT and modes and AGGRESSIVE. [1]

  6. restart once again & test.

  ~~~~~~~~~~~~~~~~~~~~~~~~
  [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not the list of installed updates.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Vista start not only restored at the factory and safe mode does not work

  Hello

  I have experience blackheads on the dell splash screen, then it continues to the f1 f2 to Setup because I don't have a floppy drive, it is okay to continue. On this screen but I have blue dashes experience everywhere in this moving around every 20 seconds or more. When I hit f1 I get a low quality graphics Windows load bar and then a black screen after 5 to 10 seconds. Followed by a blue screen of death with the code 0x0000008e. Then restart. I then tried the F8 key and restored in a last known point that worked, does not solve my problem. Tried to boot in SafeMode (normal) and I get the blue wheel scrolling as it's almost here, and then a reboot without explanation. Also, I tried to move the cards gfx and switching of slot machines, this is not having an effect. But I noticed when using a card, I get a quick 5 beep at startup, then using the other card it works fine. Is a card? This would have an effect on my boot because of the missing material? Help, please!
  Data sheet:
  Dell XPS 630i
  Quad Core - 2.4 ghz
  4 GB RAM
  Dual Nvidia 9800gt
  I have known 3 hard disks
  Windows Vista 32-bit sp1

  Hello

  Looks like a graphic problem

  beep codes are normally related material

  read below

  http://www.computerhope.com/beep.htm

  http://www.pchell.com/hardware/beepcodes.shtml

• She launched 'System Restore' now the computer will not complete the installation

  Clean HP Pavilion bought in 2003.  With the help of daughter for school work.  Computer running very slow.  A ran all the relevant boxes virus / malware scans, the old deleted files ' ran fix disk, disk cleanup and defrag, still running slow.  A ran the 'System Restore' edge (press F10 during boot).  It works through the restore program and sit as I just opened the box.  Through the implementation of procedures and click Finish and it is just there for up to 6 hours before I finally gave up.

  Oh Dear Brian, I hope there is no data file on the computer, you will need in the future. The F10 key is the path to the system recovery that restores the computer to the factory settings. It comes to the computer when it was bought new in 2003. It erases all the data files and installed programs from the drive. In other words, you start again:
  http://www.pctechbytes.com/HP/HP-recovery/

  What is the exact model of HP Pavilion?

• Pavilion dv6t-2000: replacing old HARD disk with the new SDS and loading the OS with 1 & 2 recovery discs fails

  I just successfully replace the SSD, exchanging an old 250 GB HDD with a new 250 GB HARD drive.

  I started with success, inserted the disc of recovery by the instructions on the screen. Disc 1 and rendered, it succeeded.  When you are prompted, load disc 2, which was also successful.  When asked, in charge of the "application and driver recovery CD" and continued.

  At this point the computer restarted several times, as he said it would be completion of installation of all elements.  Then he came with a message that says: the recovery attempt failed. Select one of the following buttons.

  "Save Log"; 'Details '; 'Retry '.

  Details says:

  ChkErrBB.CMD: Detects an error in the PININST_BBV.

  ChkErrBB.CMD: check c:\system.sav\logs\BurnBootWarn.log

  Any suggestions here?

  I update my BIOS before proceeding with the Exchange.

  I found the solution to this problem was already answered here:

  http://h30434.www3.HP.com/T5/notebook-recovery/quot-detect-some-error-during-PININST-BBV-quot/TD-p/2593075

  Thank you!

• Is there an easy way to restore all panels to their original state?

  I have been using Adobe Classroom in a Book and have re-wired some panels the wrong way.  This means that they are not more like the book.  Is a shortcut or another method to restore the State of out-of-the-box?

  You can restore the preferences of Muse to its original state by disabling them. So get out of Muse and delete the folder AdobeMuse to the following location:

  Mac OS: ~/Library/Preferences

  Windows XP: %APPDATA%\protector.exe

  Windows 7: %APPDATA%\protector.exe

  Now when you restart the application, all preferences must be restored to its original state.

  Thank you

  Vinayak

• my computer crashed and restored using the system recovery disk. I saved all the files using a .fbw format. I can't read. What should I do?

  My computer crashed while updating. It's a double 4 year old HP desktop processor. I could get into the repair screen, but nothing would be useful. I backed up data (115 GB) using the tools available on a drive hard usb. They are under the folder MINWIN and meet 31 different files. All I get is the demand to put in the disc. I copied the last file on DVD, but it will not read it. All other recovery programs say there is no backup file.

  I have backup, with an extension of FBW 32 files
  Help

  Hello

  1. are you able to boot to the desktop now?

  2 have you tried to reinstall the operating system?
  3. what program did you use to create a backup?
  4. do you get an error code or error message?

  According toOberwald, it seems that fbw files are generated by HP, not Vista backup tool. I suggest you to read the following article to restore files from Microsoft.

  Backup and restore: frequently asked questions:
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

  If you are not able to boot to the desktop, then I would suggest trying the following methods and check if it helps.

  Method 1:
  Start in safe mode and then try to run the restoration of the system to a point before you install the update and check if the problem persists.
  Step 1: Start in SafeMode in Windows 7:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2: System Restore:

  http://Windows.Microsoft.com/en-us/Windows-Vista/products/features/system-restore

  Method 2:

  If you used a third-party program, and then try to restore using the same program and check that it works.

  Also check the FAQ from HP or post the question on a forum of HP.

  Hope the information is useful.

• The installation of the manufacturer DVD read error: "insert a disc.

  Running Vista Business SP2 on an Athlon 3700 + I can't open a couple with my internal drive DDL Memorex 16 x DVD of installation of the manufacturer. I can read/burn discs, I burned and play movies. I tried to uninstall the driver and the removal of the upper and lower classes in the registry. I have attached an old DVD external firewire Sony and it will read the discs and the autorun on their part very well. I also ran a virus with Avast check last night. I have Roxio Creator 2010 and WinDVD 2010 installed but I don't think they are the problem other that change the AutoPlay on movies of Cineplayer.  I spent several hours on this and am puzzled. Someone has an idea it might be?

  Oh yes, I also ran Microsoft auto repair program and when he got to the point where you select the disks to run additional tests he selects the drive "D:" problem Then he spits the disc by the manufacturer and says "insert a disc.

  The drive laser is defective with the specific media type.

  Either buy a new or replacement under warranty request if it is in warranty period.

  S.Chatterjee

• my cursor floating to and disrupt the layout, how can I restore my computer to its original state

  my cursor keeps floating offshore on its own and changed the fonts on my computer and do not know how to restore it to its original state

  Hello JeanSteel,

  I suggest try to perform a system restore to a time before having this problem.  If you want to restore your computer to factory settings, I would suggest contacting the manufacturer on the guidelines for this.  Also, be sure to back up your data before doing this.  Here is a link to perform a system restore.  Please let us know status.

  System Restore:

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  Thank you