MDSM loses communication to MD3000 when new disk inserted

Similar Questions

• I "dragged" a folder of a drive on the DESKTOP so I could copy on a new disk. When they are copied to a new disk, the file is empty. The file is recoverable?

  I "dragged" a folder of a drive on the DESKTOP so I could copy on a new disk.  When they are copied to a new disk, the file is empty.  The file is recoverable?

  Hello

  You can try this program for recover data:

  http://www.Piriform.com/Recuva

  See you soon.

• It is essential to disable CS6 apps when a new DISK is used, with a new facility? (on the same computer)

  Hi guys,.

  I have CS6 Production Premium installed on my old iMac (in a "traditional HD)"

  Now, I've added a new SSD for my (now former) machine

  My plan is to do a new installation for the system and all my applications on this new SSD, including those from Adobe.

  My question is: it is necessary to DISABLE the CS6 apps on my old HD before you install and activate these apps on my new SSD? Or is not needed? (later, once I check that everything goes great with my new SSD, my plan is to erase and format the old HD to use it as a department store)

  I ask this question because I read as 'Deactivation' is necessary when you switch from an old computer to a new one. But on this case, the computer is the same, it's just a new DISK SSD that will be used for the system and applications.

  Thank you! :-)

  Activating puts a 'mark of use' in the Adobe database... you are allowed only TWO active activations... so if you enable one, your 2nd install use then your activation allowed 2nd... where is indifferent (new drive in the same computer or on a different computer) only the fact that activation adds a 'brand usage' in database activation

• If time machine is incremental how it removes previous versions when the disk is full, without breaking the chain, so do not be able to restore all changes since the first full file

  If time machine is incremental how it removes previous versions when the disk is full, without breaking the chain, so do not be able to restore the file with any changes made since the full backup first file...

  If the TM drive storage is full TM automatically deletes the version the oldest files for the new incremental backups can be made. Thus, in this case you cannot restore the versions that TM deleted because it takes more storage.

• Why my ipad loses the wifi connection when I abandon my modem wireless of Qwest

  Why my ipad loses the wifi connection when I abandon my modem wireless of Qwest

  WiFi connections are losing their strength increases the distance between the router and so as a general rule, there are some conflicting objects

  Try the following steps please

  The following actions and after each test to see if the issue is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  4. Settings - WiFi - < network name > - Click on forget network - do a restart forced according to 3 and then add again the network
  5. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  6. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  7. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  8. Backup the device to iTunes - restore as NEW (no) - see if solves problem - if yes - restore backup
  9. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• Time Machine the new disk transfer has not moved all the time

  I have a Time Machine backup to an external drive. It works very well. However, he was beginning to run out of space, so I bought a new, bigger HD.

  I followed all the steps of Time Machine: how to transfer backups from a current backup disk to a new backup drive - Apple Support.

  I then waited 12 hours for that copy.

  Around midnight, I noticed the copy is complete. There was a message that iWork had not been copied because he needed a different operating system. But I rejected. There are no other messages.

  I changed the Time Machine preferences on the new disk. And fell asleep.

  This morning, I walked into a Time Machine.

  Only the first date from July 2014, was on the new disc of TM. Then there was five times after midnight when the new drive was saved.

  But there is nothing in any of the years between the first date and after midnight.

  I know that there are hundreds of TM captures on the original disc. And I've used them very well.

  I tried to copy individual files from the old drive to TM to the new, but it is not possible to "change the backups."

  10.10.5 system

  What should do?

  While in Time Machine, to see all the volumes mounted shift - command - c.    Information derived from Linc Davis.

  If this does not work, try to copy the file to disk/restore utility using to copy the backup to a new location. Please note that this will reformat the destination partition.

• Re: Equium A60 PSA67E - can't burn new disks

  I'm losing the will to live now. Could someone help me please.
  I have a 2004 Equium A60 PSA67E-00400C8J.
  It reads and writes on DVD RAM RW and DVD ROM and CD RW that have pre files written on them.
  But, I can't get to see a new brand.

  I place several brands in the draw, closed and it works ok until you get auto white screen as you might indicate the contents of the file, but when I try and 'drag and drop' for her, he said: "there is an unknown problem and files of continue to fly in the air for always (10. (, 15, 20 minutes) until I get advice and "Cancel". Nothing is transferred at all. In desperation, I look at 'properties' for the drive and blue on the slice of cake, telling me the disk is full.
  Each new disc! several brands! all the same. I'm close to throwing out the window.

  Please please experts with suggestions would be welcome. I'll try anything.
  I know much too little for this and all officially released I've read seems to be written for a much longer young and sends me off the coast in total confusion. It took me an hour to reach this post on this forum, but I'll try.

  Please take pitty and talk in terms of Janet and John if you offer tests or responses.

  Thank you very much in anticipation

  David

  If I understand your question, your CD/DVD drive cannot burn new disks.
  Is this good?

  What discs can not be burned? Are these discs copy protected?
  Have you tried different burning software?

  I use Nero and I think it s better combustion of the program.
  Recommend to use.

• My drawer does not open on my hp pavilion s7320 npc do I need a new disk

  My drawer does not open on my hp pavilion s7320 npc do I need a new disk

  Hi tonelocs79,

  1. did you of recent changes on the computer?

  2 when was the last time it was working fine?

  See the below link for the HP website and check if it helps.

  Opening a stuck CD or DVD Drive Tray

• RESOLVED: Loop of reboot after installing new disks in RAID of PERC S100

  A customer has a Dell T110 (with a PERC S100 RAID controller) running Windows 2008 R2. The system has two disks: a reader not RAID (C :) running the operating system and a RAID1 drive (E :) sharing data with network folders.) We need to install again, larger disks for the RAID.

  I thought I could backup the data on the RAID drive existing (e), install new disks, built a new table in the S100 (VDM) virtual disk boot manager, boot into the operating system, create the new partition for the data replaced E: drive and copy the data back. This was not the case. After installing the new disks and the new array of construction (which is reported as "READY (R/W)" when starting, Windows starts all the way in "press CTRL-ALT-DEL to log". After two or three seconds, the system reboots. The same thing happens when I try to start safe mode. The system IS NOT automatically booted to the Recovery Console. He never seems to know that an error occurred and the system was not shut down normally.

  I booted into the Recovery Console, installed the drivers for the PERC S100 and run recovery to start without success. Also in the Recovery Console, I ran 'chkdsk /f E:\. ' (remarkably, the drive letter for the data drive remained the same), and no error has been reported. I also reinstalled drivers S100 of the recovery using DISM Console, but that changed nothing.

  I started to 8.1 Windows PE, installed drivers S100, formatted the virtual disk, copied the data which he, and everything works fine. The only problem is when I try to boot from the system drive (which has no problem) with the new installed disks.

  When I put the old records, the system boots normally with no reconfiguration required. The VDM to start automatically remembers the discs and the table. Nothing shows up in the logs event indicating that there was an error during startup. (Ntbtlog.txt) start-up newspaper, after several boots with the new drives in place, indicates that the system restarts at various times during loading drivers. There is nothing coherent in the startup log to indicate what the problem is.

  The only clue I have is that, during the startup, the VDM reports the virtual drive of origin as 'NORMAL (R/W)' and the new virtual disk as "READY (R/W)", but I'm not sure of the significance of this difference or if it suggests a solution.

  I can't find clues in all the newspapers about what may be the problem. If anyone has any suggestions, I will be grateful. I'll be especially grateful for the wacky suggestions.

  I ran it. Nothing appeared unusual. However, I does not solve the problem.

  I connect the new readers to the same SATA ports as the old records. When I connect one of them to the SATA port that had not been used as part of the original painting, the VDM S100 reported the original failed array, because readers were is more connected and showed the new table as a LOAN. The operating system then started normally.

  The trick, it seems that you should remove the old virtual disk before connecting the new disks on the same ports.

• Adding new disk unassigned

  Hello

  We changed a defective disk (has no data on the subject) in the slot 9 of our MD3000i with a new drive, when I'm in MD Manager said table optimal. When I go to the hardware component - physical disks , I can see all readers said affected, but the Player 9 says unallocated. We have 2 new drives in the unit and I want to create a new disk group and a new virtual disk from these 2 players more reader 9 so when I go to create a new disk group it I can see Unassigned disc 9 and the other 2 discs.

  quesiton:

  Why Player 9 say no affected? can I go ahead and create my discs with Player 9 group and the other 2 drives?

  Thank you

  Hello mrshahin,

  Yes that's correct.  When you create the new disk groups it only will allow you to do with disks that are not assigned to another group of disks.  For 7, 8, & 9 are showing as unused, so you can use them to make a new disk group.

  Please let us know if you have any other questions

• I have 200 GB of free space on my hard drive but I'm not able to make a new disk partition.

  I have 200 GB of free space on my hard drive but I'm not able to make a new disk partition. When I click on new simple volume in management records and steps of preforms a message (IT IS NOR ENOUGH SPACE ON THE DISK to COMPLETE THIS OPERATION.)   appears.

  Please HELPnot able to make a d

  Assuming that C: is the drive of victory that the size is too small, you need at least 100 GB for the drive to victory.

  (on this particular sys disk win uses 128 GB and with libraries located on a second disk, the disk win itself is 240 GB)

  You might care to use the home Version page free;

  http://www.partition-tool.com/ (EaseUS) because it has more options/capabilities than the tools management integrated disk.

  Have BTW you kept your Vista recovery disks and its key as if you need to reinstall from disc to upgrade to win7 that you will first install Vista

• [CARS] Add the new disk in the database running environment

  Hi all

  I want to ask a question about oracle RAC especially to add a new disk.

  Here's the situation for existing oracle RAC

  1. There is 1 oracle clusterware (CRS), ASM and 2 node RAC

  2. There is a demand to add a new disk to existing diskgroup

  3. all CRS, ASM and RAC is in the online state

  I read document oracle (How to add a new disc to year Diskgroup existing RAC Cluster or stand-alone Configuration of ASM (Best Practices).) (Doc ID 557348.1()

  My question is,

  1. that I should stop the database, ASM and CRS when add a new disk to existing diskgroup?

  2. are there steps that has already been proven to add a new disk in an operational environment?

  Thank you

  Adrian

  My question is,

  1. that I should stop the database, ASM and CRS when add a new disk to existing diskgroup?

  No, you need not bring down the ASM or DB

  2. are there steps that has already been proven to add a new disk in an operational environment?

  Yes, you can add the disk, ASM automatically rebalance and share the workload on the new disk.

  http://docs.Oracle.com/CD/B28359_01/server.111/b31107/asmdiskgrps.htm#OSTMG10070

  There are number of blog posts about adding disks in a diskgroup

  MRMESSIN Oracle Database Administration: Add or remove disks from the ASM disk on the database group active

• 5.4 OpenManage cannot initialize new disks PowerEdge 840

  I'm bored of Array Manager. I think Openmanage is a poor substitute.

  I have a new Dell PowerEdge 840 Server with two disks SAS and SAS 5i/R controller of berries in a mirror Raid-1 (made in hardware)

  I have installed OpenManage 5.4 WITH the storage option.

  I put two new hard drives SAS I want to initialize and create another virtual disk of Raid-1.

  OpenManage sees the drives (loans and OK but not online) and gives me two options under tasks "Blink" and "Unblink.

  Now when I put two drives in my component Snap Server PowerEdge 1600SC Array Manager 3.6 MMC 3 years, I could create a virtual disk from the operating system.

  What happens with Array Manager. Why he let do this to me?

  What is going on? Why can't initialize new disks and create a virtual disk?

  It comes to my main server. I can't take it offline for 10 hours initialize disks.

  I went into Windows disk management and that he sees the drives but I don't want a Software Raid.

  Thank you

  Lara

  
  

• I had to reinstall all my programs and data to a new disk, the old crashed. During the installation of Flash Player, I can't go any further than the password stage as he rejects. Again the username and password have been accepted without any problem to ac

  I had to reinstall all my programs and data to a new disk, the old crashed. During the installation of Flash Player, I can't go any further than the password stage as he rejects. Again the username and password have been accepted without any problem to access Adobe.

  Strangely the same problem occurs when I try to install and older version of Lightroom 4.

  Can you help me?

  Hello

  It is the OS, not Flash drive, to ask for the password.  Please refer to the FAQ what userid & password I need to install Flash Player? for assistance.

  --

  Maria

• How to add a row in a computer using New-disk virtual hard?

  Hello

  I am running powercli 5.0.1 build 581491 and I'm writing a powercli script for:

  (1) create a RDM

  (2) assign the RDM to VM1

  (3) assign the same RDM to VM2

  I am able to create the ROW and assign it to VM1, but I am unable to use "New drive" assign to VM2.  Using the following command, I am able to create the ROW and assign it to VM1.

  New-disk-hard - VM VM1 DiskType - RawVirtual /vmfs/devices/disks/naa.60000970000192603729533030353531 - DeviceName

  While trying to assign to VM2, I do the following:

  New-harddisk - VM, VM2 - DiskPath ' [san - datastore:1] vm1/vm1_1.vmdk.

  And I get the following error:

  New-hard drive: 06/06/2012 14:13:19 new-support device Incompatible hard disk specified for the device '0'.

  What I realized, is that if I create a regular vmdk file, then use the New drive using the '-DiskPath ' option, then the command works well.  So my question is, what is the command to add a ROW in a virtual machine?

  Thanks in advance.

  No, indeed it seems something wrong with the cmdlet New-disk hard when adding shared RDMs.

  I have the following, which assigns the RDM common to both virtual machines.

  It's more or less the same, what you've seen in Onyx, but it adds the RDM shared for two virtual machines.

  $vm1 = Get-VM -Name VM1 $vm2 = Get-VM -Name VM2
  $DeviceName = "/vmfs/devices/disks/naa.600507680180701ed00000000000124" 
  
  $hd1 = New-HardDisk -VM $vm1 -DeviceName $DeviceName -DiskType RawVirtual $ctrl1 = New-ScsiController -HardDisk $hd -BusSharingMode Virtual -Type VirtualLsiLogicSAS
  $spec = New-Object VMware.Vim.VirtualMachineConfigSpec
  $spec.DeviceChange += New-Object VMware.Vim.VirtualDeviceConfigSpec $spec.deviceChange[0].device += $ctrl1.ExtensionData $spec.deviceChange[0].device.Key = -101$spec.deviceChange[0].operation = "add"
  $spec.DeviceChange += New-Object VMware.Vim.VirtualDeviceConfigSpec$spec.deviceChange[1].device += $hd1.ExtensionData$spec.deviceChange[1].device.Key = -102$spec.deviceChange[1].device.ControllerKey = -101$spec.deviceChange[1].operation = "add"
  
  $vm2.ExtensionData.ReconfigVM($spec)