Memory resource problem

Similar Questions

• Tecra M9 - compatibility of memory resources

  Hello

  I really apreciate if someone having a Tecra M9 (S5515X or S5513X), check the memory resources in the control panel. And inform me which appear on the Device Manager.

  Please, go to control panel / system / hardware / device manager
  Menu display / resources by type / memory.

  Appearing something like this

  [000 A 0000 - 000BFFFF]-...
  [000 A 0000 - 000BFFFF]-...
  [000CC000 - 000CFFFF]-...
  [000DC000 - 000DFFFF]-...

  I need the description of memory occupancy for the Bank 000D 0000 to 000DFFFF.

  I need this information to verify the compatibility with my card PCMCIA for Siemens, which can only work if the 000Dxxxxx of the Bank of memory is not used for another device. I need to check this allow to purchase the Tecra M9.

  Best regards

  Heitor.

  Hello

  I can't provide you with any information on memory usage because I am not owner Tecra M9. But I found on the internet of information on the card slot PC of Tecra M9.

  The Type II 5mm PC card slot can accommodate unique Type II 16-bit or 32-bit (CardBus) PC cards.
  So if your Siemens card is compatible with the specifications of this material I see no reason why he shouldn't? t works with the laptop Tecra M9.

  Greetings

• Memory Allocation problem when using JNI

  For a project, we need to interface Labwindows CVI / Teststand with an application written in Java. We use JNI. The code uses JNI_CreateJavaVM to start a JAVA virtual machine to run the Java interface code. The code did run for quite awhile, but now (without any obvious changes on the side of the CVI or on the coast of Java) JNI_CreateJavaVM will fail with the error-4 code, this means that of the JAVA virtual machine failed to start due to the failure of allocation memory. First investigation shows that even if the Windows Task Manager shows approximately 600 M free physical memory, you can allocate in ICB only about 250 M as a single block at the point where we call JNI_CreateJavaVM. Maybe it's a little less because we have - Xmx192m to the JAVA virtual machine to run our code. Unfortunately just to increase the physical memory of the machine of 1.5 G to 2G doesn't change anything. Free memory space in the Task Manager showed increases, but the memory total block size does not work. Are the trick to optimize the CVI/Teststand who use cases?  Or maybe the problems with JNI?

  Finally, it was a memory fragmentation problem with TestStand. See details/solution here

• POWEREDGE 2800 memory/battery problem

  Hello

  The server DELL POWEREDGE 2800 our company with windows sbs 2003 suddeenly server has restarted yesterday and stuck in the POST gives the error"

  Memory/battery problems were detected.

  The adapter has recovered, but cached data have been lost.

  Press a key to continue. "

  I have three times restarted the server by pressing a button to continue. All three time loading of bones preserved for a long time and restarted the same screen of the error.

  ATLAST I turned off the server and checked for any loose contacts according to the suggestion of dell. I removed the disk 0, 2 HHD, HDD3 in channel one o and replugged in and started the server. Same system has occurred. 1 HARD disc is already failed in RAID 5 and the place so that the disc is empty, I suspected may be another disk HARD in the same row is a failure and so I removed HDD 0 and rebooted the server. the same symptom (2003 loaded and stuck). turned off the server ' reconnected HDD0 and removed HDD2 and restarted the server, but the same symptom.

  Reconnected the HDD 2 and disconnected HDD3 after restarting the server, it gives error loading operating system.

  There are disk HARD 4 and 5 two more hard drive HARD drive in another channel 1

  How to recover from this problem and our secure server data?

  Please help me with this because I'm helpless and the server must be brought im production tomorrow

  Thank you & best regards

  Margot

  If your LCD is blue and you get the error of memory/battery on each startup, then you need to replace memory RAID (99% chance that it is rarely a defective battery or the riser).  The operating system will not usually start in this scenario.

  If your LCD is amber and a message about the scrolling ROMB battery voltage, you should replace the RAID battery (sometimes it's because of riser).  The operating system will usually start and work very well in this scenario.

  First of all, stop playing with readers and replace the memory RAID (and battery and lift to be 100% sure).  Once it is replaced, due to all mixture player you have done, you might have a few steps very careful to recover your data and make your table online.  When you're ready to do this (again, it is useless before repairing the message memory/battery), call Dell technical support - it's always free on servers, regardless of the status of the guarantee.

• "The memory resources available in the pool of resources of the parent are insufficient for the operations." ... Really?

  Hello

  We have three virtual machines on a host computer. They need to be pinned to this host and with reserved memory: 1 GB, 4 GB, 8 GB.

  We are talking about 13 GB of RAM on a physical server that has 16 GB of physical RAM.

  When I Power On last VM, I get the following error:

  "The memory resources available in the pool of resources of the parent are not enough for the operation."

  I have a second host with the same size of memory and use reach 14GB of memory.

  I know that each virtual machine wants more memory than what we have configured, but I would like to know if it's a "bug" or

  something we can fix via vCenter configuration, or we really need more physical memory.

  Please find attached the config of memory for the virtual machine and the host State.

  Thanks in advance for your help.

  Host needs some memory as well for things like vmkernel, drivers and other components and you will not be able to touch this area with reserves of VM. It is not a bug, more like a fuse. You will not be allowed to book all of the physical RAM to VMs and / or resource pools.

  In your case, you should either decrease the reserves (why are you booking 100% memory for your virtual machines? What you're trying to achieve with this setting? Is it an obligation of the seller to App?) or increase the amount of physical RAM on the host.

  Of course this depends on your specific requirements and management policies of the resources, but in most cases I've seen, reservations are only affected when there is a heavy statement memory and using actions alone is not enough. Even so, reservations are usually configured only for very high priority / criticality VMs and not 100%, but rather a little before "stable / persistent peak memory Active" value. F.x. If a particular virtual machine has more mem use regularly on Wednesday 1-3 PM and memory active value for this period is 3 GB, a reservation is usually set to something like 4GB.

  I hope this helps.

• The memory resources available in the pool of resources of the parent are not enough for this operation

  Hello

  I tried to light a Nexus 1000V VM running on a 5.1 ESXi on a 5.5 vSphere vCenter and I get an error message about the available memory resources. I'm running on a virtual server with 10 GB of RAM and 60 GB HARD drive. The physical host machine has 16 GB of RAM and 320 HARD drive. I am a beginner in this so please try to be clear. Thank you very much.

  Hello

  It is possible to have a reserve of memory on the 1000v (I think that the model comes with them as standard when you deploy).

  If you right-click the virtual machine and 'Settings' and then go to the tab "resources", under the heading 'Memory', you have whatever it is the value of the booking?

  It would look like this: http://i.imgur.com/ftBZENv.png

  If she has a reservation, you could safley assign 0MB (removes the reservation). This could be preventing it from power.

  Otherwise, you run a cluster in vCenter? You have active HA?

• Please suggest tool use ability to control host and VMs CPU, memory resources.

  Please suggest tool use ability to control host and VMs CPU, memory resources. What are the parameters to be monitored, their level of thresholds.

  What is the TOP / ESXTOP.

  Hi friend

  Here's the blog post detailed ESXTOP:

  http://www.yellow-bricks.com/ESXTOP/

  There is a VCOPS product that can also help you to understand so many parameters. You can try the license of the Foundation which is free of cost. There is a lot of intelligence if you go for paid VCOPS.

  VCenter graphs/stats can also help you as well.

• memory resource limits

  I am struggling with the justification for the existence of limits of memory resources.

  Why a virtual machine would (for example) 2GB memory configured in "virtual machine properties | material"and have a limit of 1 GB under" properties of the virtual machine. resources? "Why not just configure it with 1 GB of memory?

  Also, if a virtual computer is configured with a memory of 2 GB, but has a limit of 1 GB, would he think always that she had at least 1 GB free memory and never page?

  Can someone give me a realistic scenario for the use of resource memory limits?

  Thank you

  -dog

  Honestly, I don't think you'll find a good.

• Memory resources

  I have a host that has 2 GB of physical memory.  On the Summary tab, it confirms it.  On the tab "allocation of resources", it shows a total capacity of 181MB of memory.  I have 2 guests, a Vista of 512 MB and 256 MB XP host.  I don't have any installation of reserves.  I can start a VM, but the other will give an error of 'not enough memory resources'.  Any ideas what would cause this?  It is configured in a cluster with 2 other guests.  Any ideas what is the cause?  It worked ok before in a non-clustered scenario.

  2 GB is the minimum size of mem to install ESX/ESXi 4.0.

  Add memory if you plan to use to run virtual machines.

  André

• ModtDestroySessionHandle does not release all memory resources

  Hello

  I have a program that attempts to do 1000 iteriations to read the message of the RF, but I get the error "not enough memory to complete this operation" popup. Look like memory leaks about 520 iterations.

  In this loop, I ModtCreateSessionHandle (& modt_Hdl) initially inside the loop and ModtDestroySessionHandle (modt_Hdl); in the end inside the loop. I had to move both ModtCreateSessionHandle (& modt_Hdl) and and ModtDestroySessionHandle (modt_Hdl) outside the loop to solve the problem.

  Should and release all the atttached of resource memory for mod_Hdl ModtDestroySessionHandle (modt_Hdl)?

  Kind regards

  Shane

  Hiya Shane,

  Thanks for your comments. You are quite correct, the ModtDestroySessionHandle should allow you to free up internal resources and ignores the ModtHandle created using the ModtCreateSessionHandle function. To ensure the appropriate memory release, this function must be called for every ModtHandle created with the ModtCreateSessionHandle function.

  Therefore, I am surprised to hear about memory leaks you have described. However, regardless of the memory leaks, the process of constantly creating sessions (memory allocation) and destruction (deallocation of memory) is horribly inefficient.

  The solution you found yourself is a case of very typical use for modulation functions. Pulling your create and destroy calls outside the loop, you only asked once, but always refferencing the sessions in the loop.

  I will feed your comments to our R & D team, so that we publish handles and allocated memory space as carefully as possible. However, your original architecture is not an intended use function calls, and functions may not be tested in this way. My gut feeling is that maybe every time we create the handle, must have a block of contiguous memory. If there is no variation in grip size, this could cause the 'memory leak' over time. My final comment is purely speculative.

  Ultimately, by following the correct use of the functions you have improved the effecientcy stripped yopur enforcement and removed the potential memory leak.

  Thanks again for your results display.

  Best wishes and greetings,

• Memory - host vs. comments memory resource allocation

  Hi all

  I have read several topics about this, but nothing specific to what I have to ask.

  I understand that the memory of the host is the amount of RAM that uses a virtual machine from its host and client memory is supposed to represent the percent of this host, the guest is the use of the RAM.

  My question comes here... I have a SharePoint VM which has 8 GB RAM allocated and the Mem % prompt is about 20%.  But if I check Task Manager/performance monitor on the VM console, the guest is sitting to 7.5 g.  I'm looking to upgrade of its resources, that's why I started to look in here, but I'm confused as to how this Mem % Guest may possibly be accurate.

  This is a common problem when this counter is inaccurate or have I missed something?

  Thank you for your time and help!

  Ryan

  The host uses an algorithm of memory 'active' to determine the amount of memory is active using the virtual machine.

  The guest VM operating system shows a memory dedicated to running applications and processes.

  These two will rarely be the same.

• memory day problems post 10.11.6?

  In the last days, safari has been giving me the BBOD, and crashing several times a day. Less critical (but hey, it's a holiday weekend) lies in the fact that I can't play the games (minecraft) because the application continues to run out of memory, despite the fact that I have 32 GB of ram. There is a process of kernel running at the level of the root that starts normally, but then the spikes to use all available memory (less than 2 GB to 18 GB - Yes gigabytes is - and all applications must be suspended at this time).

  Does anyone else have problems of memory after this last update? I don't think it's a coincidence that safari, memory and kernel of processes are involved in updates and my problems, but I am not an expert. Anyone have any ideas?

  I'm running an i - mac 2013 with 3.5 GHz intel core i7:

  

  

  AnneMarie

  < re-titled by host >

  Please download and install EtreCheck from http://etrecheck.com/

  Run it and post the report here.

• HP Compaq 6000 Pro SFF: HP Compaq 6000 Pro Compact (SFF) - memory upgrade problems

  < <! UPGRADE MEMORY SHOULDN'T BE COMPLICATED! > >

  Chassis: HP Compaq 6000 Pro Compact

  Processor: Intel Core 2 Duo @3. 00 GHz

  RAM: 2 x 1 GB

  OS: Windows 7 Pro 64-bit

  I can add more technical info on request.

  Recently saved this PC of my friend tries to throw it. Everything is fine with the PC. It works perfectly and there is no material visible failure wihtin the PC either. He just bought a new and had no need for this one.

  Before turn me this into a House mutli-purpose server, I decided to upgrade the RAM.

  So I did some research and found this page: http://h10032.www1.hp.com/ctg/Manual/c01883661

  DDR3 240-pin DIMM 1333 MHz non - ECC, Max 4 GB per DIMM slot, Total Max 16 GB module.

  I went and bought RAM Corsair. Link to the product: http://www.corsair.com/en-us/cmv4gx3m1a1333c9

  I decided to get 2x4gb and upgrade later if I felt the need.

  I was happy to install in the PC. one in DIMM 1 slot and the other in the DIMM 2 slot.

  BEEP BEEP BEEP BEEP BEEP!

  I thought that maybe the slots are wrong, maybe they have to odd numbers then numbers.

  So I changed the RAM of DIMM 2 DIMM 3.

  Once again, the annoying ringtone.

  I even tried leaving just the 4 GB DIMM 1 and tried to start the PC, but nothing helped.

  I tried a lot of different combinations with the end result is 5 annoying beeps.

  After that I thought that maybe, just maybe, an update of the BIOS can change things.

  So I installed Windows 7 (I can't stand Windows. Arch Linux FTW) and performing a BIOS update.

  I then installed the new RAM again. Yes... frickin 5 beeps AGAIN.

  I am extremely disappointed at this point. I spent already $ 70 on a computer with free access.

  I read the forums here, but I couldn't find a thread with a solution for me.

  Is there anyone on this forum who could lend me a helping hand?

  Any information would be gladly appreciated.

  PS Please report any stupid error, I did. Stick and stones could not curb my bones.

  Hello:

  See this related post... the elite 8000 is basically the same model as the Pro 6000.

  Resources memory very finnicky needs...

  http://h30434.www3.HP.com/T5/desktop-hardware/memory-upgrade-for-8100-elite-CMT-with-TwinMOS-2x4GB-512x8/m-p/4918937/highlight/true#M95301

• Stops at random - memory/battery problem?

  Hello

  I use a Macbook Pro (retina, 13-inch, early 2013) and OS 10.11.3

  Recently I had problems with what I thought it was my battery... The laptop randomly stops (if not connected to the power supply), usually when it is less than 50% charged. When I then connect it to the power and turn it on, my date and time was given to zero on January 1, 2013 or something.

  It becomes more and more difficult to work with, and it seems that the percentage that he dies gets higher. Sometimes I have an error message saying 'Battery of Service', but sometimes that happens and is not at other times. My battery had only 300 cycles, so I'm a bit puzzled as to why this is happening.

  In any case, just to be safe, I ran a test for Apple hardware, and I got this error: 4MEM/61/400000000

  That seems to say that there is a problem with my memory. I don't know if the problems of memory can cause such shut downs, or if it's my battery. I don't really want to take in battery life if she will come out with the same problem.

  Thank you very much for your time and help.

  Please take the computer to the Apple store to have the computer checked.

  The Genius Bar reservation:

  http://www.Apple.com/retail/Geniusbar/

  Best.

• Satellite A660 - 11 M - Memory Upgrade - problem

  Hello world!

  I'm having a problem with upgrading my RAm 4 GB to 8 GB memory ([link crucial 8 GB Kit | http://www.crucial.com/eu/store/mpartspecs.aspx?mtbpoid=28543EEAA5CA7304]) which should be compatible.

  When I turn on the laptop after mounting of the modules to all first all seem to be right and the Bios start, but then it will not load windows and stucks on a black screen.

  Could someone help?

  Thank you!

  Hello

  What to say: it looks like it s a problem with new RAM modules.
  The RAM modules aren t fully compatible or they malfunction.
  You must use other modules I made good experiences with modules from Kingston.