MEMORY TWIN

Similar Questions

• Memory twin on U840-10U

  Hi all

  AFAIK the U840-10U has a 4 GB of DDR3 memory module memory (1600 MHz). It also has an extra plug for an additional memory module. Am I wrong?

  This model has dual-channel memory technology? I mean, if I add a new additional 4 GB of DDR3 (1600 MHz) memory module, the computer would be able to access it at the same time? I'll make it through the Toshiba SAT official not to lose the warranty.

  Thank you in advance,
  Videal

  Hello

  > As far as I know the U840-10U has a 4 GB of DDR3 memory module memory (1600 MHz). It also has an extra plug for an additional memory module. Am I wrong?
  This seems to be the U840 supports two correct memory locations.
  The device supports DDR3 1600 MHz (PC3-12800) SO-DIMM 4 GB and it support dual channel.

• Equium A100-338 and memory twin

  Hello

  I see that the satellite A100-338 has a chipset intel 945 GM, who, according to intel, supports dual channel memory. Is it so? Crucial to the site it says that it's not and there is no reference to this website of toshiba. Can someone give me a definitive answer?

  Thank you

  Tom.

  See this page:

  [Memory for Toshiba Equium A100-338 | http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=28155&ft=m&st=3]

  There, you can find this info:
  Memory compatible type: * DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

  The laptop can certainly stand modules of DDR2 (dual channel)!

  Best regards

• Upgrade memory - Compaq Presario SR1630NX

  Planning the upgrade on my HP - Compaq Presario SR1630NX memory. Before buying a product of memory, I want to make sure it is compatible with the Compaq. Info on the Compaq Presario SR1630NX memory is as follows: 1) 512 MB (2 x 256) memory installed in the 4 slots 2 DIMM; (2) 2 4 DIMM slots open. (3) type of memory is 184 pins DDR SDRAM. It is a bit confusing when you try to sort the different products available memory. Identified the PNY Memory twin 2048 MB PC3200 DDR 400 MHz memory (2 x 1024MB), Model #MD2048KD1-400. Memory is this product compatible and recommended? Otherwise, any suggestions?

  Hello

  JJM says:
  I ordered the Crucial memory upgrade kit. Then will come the real installation. I'm a little tentative trying to change modules of memory because I've not done this before. Are there problems I should be aware of that I open the SR1630NX, find the motherboard and memory sticks, remove and install new?

  It's really very simple.

  All it takes is patience and attention to the location of the index in the module and the game inside the DIMM slot.

  Unplug the power connector from the power outlet.

  Open the case.

  touch something metal in the case with your hand to dissipate static electricity from your body. I actually always use an anti-static wristband.

  Press the tabs on each side of a module locking and it comes out.

  use the thumb and forefinger on each end of a module and remove it carefully.

  during the installation of the modules to place them in the same locations you deleted the 'old' of.

  Search the index of the module tab and the tab corresponding inside the ALS DIMMt.

  Use the slots on the inside and under the locking tabs guide to guide the module in the DIMM connector correctly

  now, use your thumbs to the top end of the module for shake it gently in the DIMM slot.

  you will know that it is in place as you feel / hear a click.

  now check to make sure that the locking tabs are in place at the ends of the module.

  Repeat the process with the other modules

  That's all there is to it.

  Kind regards

  ERICO

  .

• Possible advantage i7-860 vs i7-930: 16 GB of memory compared to 12 GB?

  People,

  I'm scary on a new build for CS5. I searched and read post after post and try to avoid cluttering up the jury with redundant threads. I'm quite new here and I would like to do my part by using before messages first. Many thanks to injury for his guides and others also.

  My question today does not seem to have been addressed, about the advantage of having 16 GB on the LGA-1156 platform to 12 GB on the LGA-1366. We can skip the intro and go directly to the red text if this post seem you too long.

  At this point, I gave up the fight to keep my Phenom X 4 system, especially since I have a Canon T2i which produces files in format AVCHD (thanks to all for the age of enlightenment on this issue). I realize also that other programs in CS5 are not accelerated as a body with its MEP. Therefore, it makes sense to make the jump to Intel for a platform of editing at the moment, if I want to use my AVCHD clips to straight-up without transcoding (which is something I can try a little before I sell my AMD bench). A fan of AMD, or like me a person with an AMD system, is not likely to see the situation change. Even the core 6 AMD 1090 t. does not appear huge gains in the benchmarks at the beginning.

  I teach, and what got me on AMD has been the cost of the platform. Card mother and the DDR2 memory for added savings that I put four systems in my math class. A curiosity to try and keep my setup AMD for CS5 has to realize that I could get out my mother DDR2 with 16 GB memory (4 x 4 GB per module slots) max and fill all the slots for the performance memory twin in all modules. He had me wondering if the advantage of more memory could compensate for my slower CPU. Probably not, I now think that I should always empty my Phenom X 4 for Intel platform.

  The interesting thing is that this consideration of memory 16/12 GB of the LGA-1156 versus platforms LGA-1366. It seems likely that if harm can live with 12 GB and hit the top of the benchmark with it, 12 GB sounds pretty good to me. But still, it would be nice to have the extra 4 GB.

  There may be a compromise that bridges the best of both worlds?

  The i7-860 use motherboards with 4 locations of memory. Newegg has the G.Skill DDR3 16 GB memory kit with timings of 7-7-7-18 $600 (good price, good timing). When purchased as part of a combo, you can get a decent LGA SATA 6/USB 3.0 - card mother 1156 for around $100. I love this approach, like paying $200 for a card mother just gripes me. (Which is probably stupid, because I think that if I intend using my CS5 Production Premium and my video equipment at their full capacity, I need to put together a platform that is not a bottleneck.) Why get hung up on the difference of $300 - $400 in platform when I have thousands in the rest of the things?)

  On the otherhand, if you're not saving if possible all will crawl out-of-hand quickly...

  
  

  So, what do you say? A 12 GB i7-930 platform, simply because of the memory? one prefer an i7-860 16 GB On system would see a generalized difference be it? The platform i7-930 has an advantage on the i7-860 in a dimension that could exceed the extra memory? Or don't Pr as a memory ranging from 12 to 16 GB make a noticeable difference in ease of use program, as during treatment, such that small loss in other areas paled in comparison? I could live with slightly longer render times, etc. If additional memory may make the program more accessible. From what I've read here-n-yon, ranging up to 16 GB makes a difference. But what kind of difference? Game change?
  

  
  

  I noticed there is no one i7-860 of anywhere near the top of the PPBM chart, which gives me pause. Also, I know about the update of the X 58 ' Gulftown 6 core CPU boards. But I'm going to worrry on this subject after I see how my first rig - I shoot short clips to school and that you don't have to change the length of the films.

  Bottom line-anyone here, if the construction of a new rig, would use the i7-860 on the i7-930 simply because the 860 uses a motherboard with 4 memory slots, so granting of the advantage of the 16 vs.12 GB memory? I am not 24GO in x 58 ' on board without worrying, so the choice is firming rather well. Slower platform to 16 GB resisted faster platform with 12 GB of memory.

  
  

  The nature of Premiere Pro and its needs to answer the question, or the answer fell to General Assembly as render times, etc.? Someone has cause to think that the extra 4 GB will do Pr humming better in some important aspects?

  
  

  
  

  We will relax and consider for a moment what type of disk activities take place during a normal editing session:

  1 OS access

  2 maintenance tasks made to processes and services

  3. access to the files of Tenp

  4. access to the Page files

  and forget immediately because there is not that you can do about them, apart from the reduction in the number of services and processes, in other words the system setting and increasing memory.

  Now what remains during an editing session is:

  5. access source material

  6. access to the files indexed, consistent and spikes in the media cache

  7. access to the files of pointer in the media cache database

  8 temp file access

  9. access to the preview files

  10 PR files access

  11. access to the plugin files

  12 service Manager access

  13. access to the QT service

  14 dynamic access Link

  15 etc.

  And in the meantime internal Windows continues. If the old adage that each disc of modern day is fast enough to stream video, then that in itself is correct, can become incorrect if you have enough video streams, with effects or transitions. The duration of the time line is not really relevant here.

  There is no clear cut answer that you are looking for a raid, too much depends on your style of editing and workflow. But in general, I recommend raid when you have only 3 or 4 discs (including start/OS drive) but advise for the raid when you use disks of 5 or more. Adobe forums: no RAID or RAID, this is the...

  With a limited number of available disks, raid0 is the only option you have and raid mobo is more than enough. A hardware controller is needed for this.

  I suggest try you it with your hardware source on your system without a raid. If you find that you have problems with scrolling through your timeline, quick, movement of ICT, so take a look at raid, otherwise, great, your system is fast enough for your application.

  Just my $0.02

• 16 GB of Ram for HP 8730W?

  Is is possible to put into two 8 GB memory DDR2 Ram in HP 8730W laptop Station work?

  Hello

  N ° Please read

  • Standard 800 MHz DDR2 SDRAM; two slots supporting memory twin 1024 MB, 2048 MB, 4096 MB or 8192 MB
  • Maximum upgradeable to 8192 MB with 4096 MB SODIMM in slots 1 and 2
  • Twin Maximized performance dual channel memory requires SODIMM of the same size and speed in the two memory slots.

  Kind regards.

• 2000-2313tu HP: you hp 2000-2313

  I use hp20013tu running on windows 10 64-bit without problems except low ram of 2 GB. Please refer how much maximum RAM amount can I insert on my additional location

  Please see Compaq Presario CQ58 and HP 2000 Notebook PC Maintenance and Service of Guide for more information on the maximum RAM, memory specifications and the replacement procedure.

  According to the MSG, it seems that your computer supports up to 8 GB in the following configurations;

  8192 MB (4096 MB × 2)
  6144 MB (4096 MB + 2048 × 1).
  4086-MB (4096 MB × 2 048 or 1 × 2)
  2048 MB (2 048 × 1).

  Help memory twin DDR3/1333 MHz / (DDR3, PC3-12800/1600 MHz DDR3-1333 downgrade) SODIMM

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• I think to upgr hp g62-a21sa with i3 330 m processor. What kind of Proccesor I can adapt

  My laptop has become slow a little, I need to upgrade the processor and memory. What kind of Proccesor I can adapt and what is the maximum memory ram can I use

  card mother model1439 60.22 chipset havendale/clarkdale southbrigde hm55

  Here are the specifications of your computer laptop g62-a21sa and here's the HP G62 Maintenance and Service of Guide series. Looks like the processor i7 - 620 M of Intel Arrandale™ (total 2.66 GHz, 4 MB L3 cache, 1066 MHz) - Dual core 35watts CPU and memory twin 4 GB (2 x 2 GB) DDR3 1066 MHz SODIMM memory are at the max. However, the service guide also States in "Supports up to 8 GB of memory system"

  Frank

• Using a FP-I-V5 in differential mode

  Hello

  I'm creating an application by using the Modules of Point field. I use some memory twin for i/o modules. Does anyone know how we should connect module FP-I-V5 channel as differential. Examples of the operating instructions do not cover the case of differential.

  Any help would be appreciated.

  Hello

  Dual Channel FieldPoint modules are isolated from each other. For analog modules, such as the FP HAVE V5, the two channels on the module share the same commune, while they are considered to be asymmetric. However, if you only use one channel, you don't share in common with the other channels and are therefore the differential measure.

  To use the FP-I-V5 as a differential module, simply use a single channel.

  Kind regards

  Green shores
  Support Engineer produces FieldPoint
  National Instruments

• When you try to evaluate the performance of the computer of my PC for the first time in 64-bit Windows 7, I get an error message stating "Windows Experience Index for your system could not be calculated."

  The error message also indicates: "cannot complete the assessment. The assessment or other operation did not complete successfully. This is due to an error reported from the operating system, driver or any other element. »

  I did a full install new (custom) on two WD Raptors (10,00 RPM) RAID 0 (striped).  All used harware succeeded in Vista Ultimate o/s is first available.  Current material as follows:

  Windows 7 Professional 64 bit Build 7600 v6.1.7600
  EVGA nVidia nForce 780i SLI card mother ATX
  Intel Core 2 Extreme QX9650 processor
  8 GB (4x2Go) Patriot Extreme Performance Viper Series DDR2 PC2-6400 low latency memory twin Kit, SLI-Ready (with CL Timings of 4-4-4-12 @ 2.1V)
  2 x WD 150 GB 10 K rpm 16 MB SATA NCQ in RAID 0 (striped)
  Samsung 22 x DVDRW SATA Lightscribe
  750TX (750 watts) Corsair power supply
  2 x OC from BFG GeForce 8800GTS 512 MB GDDR3 video cards in SLI
  Map its Creative SB X - Fi XtremeGamer

  All PC settings are standard (ie: no overclocking component) and all windows updates are completed.  Latest drivers installed for the video & sound cards.  Last firmware & driver for optical drive installed also.

  Any ideas as to why I can't receive a rating system for Windows Experience Index with success?  Thank you

  Stuart

  OK, I was on the phone with support for about an hour.  Problem has been resolved.  Turn user account control either the lower or penultimate level.  This version fixes the problem!

• It's time to build a new machine?

  I get the build bug now that new Nvidia cards are coming.  I would have preferred to hold off for as long as I can and let prices naturally come down, but recently (even using first 12 items) I have questions perfoirmance.  I recently started playing with AE CC and saying it's slow is an understatement.  It of time to upgrade or is anyway to improve and save my current rig.  I'm not a gamer and honestly I always use Photoshop CS3 because CC is super slow as well.  Any suggestion welcome and thanks in advance...

  Ive asked this in the AE forums as well, but I actively use Photoshop, AE and Premiere Elements and really want to have a platform that can skillfully executed all the

  * Windows 7 Pro 64-bit SP1

  * Intel Core i5 4670K @ 3.40 GHz 54 ° C

  HASWELL 22nm technology

  * 16.0 GB of DDR3 memory twin @ 799 MHz (9-9-9-24)

  * ASUSTeK COMPUTER Inc. Z87 - PRO (1150 SOCKET) 28 ° C

  * 2047 MB NVIDIA GeForce GTX 760 (PNY) 36 ° C

  SM2333T (1920x1080@60Hz)

  SM2333T (1920x1080@60Hz)

  * 1397GB Seagate ST1500DL003-9VT16L ATA Device (SATA) 47 ° C

  1863GB TOSHIBA DT01ACA200 ATA Device (SATA) 41 ° C

  1397 GB Seagate ST1500DL003-9VT16L ATA Device (SATA) 47 ° C

  1863GB TOSHIBA DT01ACA200 ATA Device (SATA) 39 ° C

  The first thing to check is the temperature of the CPU: If the temperature of 54 ° C is idling (as opposed to slot a load), you have a heat problem, which is usually caused by a thermal installed incorrectly heatsink cooler / CPU fan. In this case, when you try to do something to all the bosom of Premiere Elements, this CPU temperature springs to near 100 ° C and accelerators, then the clock speed way, way down. At idle, the CPU temperature should be only about 30 ° C, 54 ° C No.

• My notebook yourself run Premiere Pro CS4?

  Hey guys,.

  I'm new here. I was wondering if my laptop could run Premiere Pro CS4. Regardless of the conditions on adobe.com, could my laptop still run ok?

  Data sheet:

  
  Dell Studio XPS 16

  Intel Core 2 Duo P8600 - 2.4 GHz, 3 MB cache, 1066 MHz FSB

  4 GB DDR3 RAM memory twin 1067 MHz

  Graphics ATi Mobility Radeon 4670-1 GB

  320 GB AT 7200 RPM

  1920 x 1080

  Tell me if I need to add more specifications.

  Thanks in advance!

  Amazon page you can click the menu drop down and choose the 500 GB model, which is only $119 (I paid $184 last year for the 500 GB, then got the 1 TB for $155... price!). He comes to 7200 RPM drives and important features.

  No, you needn't the ExpressCard if you have an eSata port. I did not, so I was just showing what is available.

  eSata drives are not faster than internal hard drives (at least 7200 rpm ones), but they're pretty close. The point is NOT to use USB or FireWire, port ports, they are slower. But for editing on a laptop, you'll want a second disc for your support with your internal drive for the OS and creation. You can do it on a drive to the rigour, but performance will suffer. If your laptop could mount a second internal drive then that would be nice, but it's going to be a hot laptop!

• TWIN MEMORY? Z575

  Hello

  I have a laptop Lenovo IdeaPad Z575GM cu processor AMD A6 - 3400M 1.40 GHz, 4 GB, 500 GB, AMD Radeon HD 6520

  I want to 'give' another 4 GB.

  Will it work in DUAL CHANNEL?

  My index of 7 (x 64) windows current 5.9 (out of memory), I read that she should go up to 7.x something (with 8 GB Dual Chanell). Is it true?. This will improve my index of video game?

  What shoud model I chose:

  -Memoirs Kingmax 4 GB DDR3 1333 MHz laptop

  -Memoirs portable Corsair VS 4 GB DDR3 1333 MHz

  -Memoirs portable Kingston ValueRam 4 GB DDR3 1333 MHz CL9

  Sincerely Florin

  
  

• "The String to Byte Array" and its operations on-site (memory) of twins "Byte Array to string"? (or if they incur sentence of copy/memory operation?)

  I can't deduct the answer to this question (topic/post title) of the help of LabVIEW on the functions.

  Intuitively, it seems that the two representations of data are equal to the memory and so goes between the two should essentially be a no-op when the code is compiled... but is it? (assuming that the length of the array of strings/remains constant, can I go back repeatedly without performance?)

  As a string of LabVIEW is a handful and any other type of data except tables aren't a handful; that implies to me that a string = U8-table-grip handle and so a string into an array of U8-could be a memory or inefficient operation since no conversion actually take place?

  The reason I ask, is that when you work with for example TCP Read or read VISA, 'data' reading is always a string, but according to what you are doing, this string is often more efficiently processed/interpreted if converted to an array of U8 and I just want to know if (memory and CPU point of view) I can move freely between the chain and U8 array and return depending on what format is most appropriate to a point?

  (Also, I'm at this stage fairly certain that the "array of strings of bytes" is cleaner AND more efficient than a type-cast to an array of U8 strin... but I could be wrong.)

  I did some tests on this just now, and my conclusion is that it is completely in place. The local users group had a coding challenge when this became relevant to my solution.

• EliteBook 8540w: identification of Slot Correct memory for twin Enable memory RAM upgrade

  I just bought an opportunity Elitebook 8540w with i7 quad core and four memory locations (I love it!).  It is running 64-bit Windows 7 Professional he came with a 4 GB memory module and I bought an additional module of 4 GB to 8 GB of total RAM.

  I have the HP document that shows both modules of memory of 4 GB, it takes in the memory slot 1 and the other in the memory slot 3 for the proper functioning of the memory double channel.  All together right?

  Not quite.  In the Elitebook 8540w, primary under the keyboard memory locations are clearly labelled '1' and '2' However, the locations of memory expansion on the underside of the chassis are also clearly labelled Opps '1' and '2 '!  There is no '3' and there is no '4' in which three vacant slots we installed the second module of 4 GB for the proper functioning of the dual memory channel?

  All the facts on how to proceed would be greatly appreciated.  Thank you.

  Good old CPU - Z... a Swiss army knife of a free application that must be in every tech toolkit.

  http://diaryofdennis.com/2012/11/12/how-to-check-if-your-computer-memory-is-running-in-dual-channel-mode/

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.