MGCP router/gateway in CUCM update

Similar Questions

• Encryption advice please WRT160N router/gateway/modem wireless

  I would like clarification on security and encryption please.

  I have a WRT160N router/gateway/modem wireless with WPA security is enabled.  I have a wired office with LELA installed and a wireless laptop.  A key is required when connecting the laptop but on page properties in LELA, it says "wireless encryption - no ' is this extra encryption in addition to the security theWPA. WH n I try to enable it, LELA asks the password admin but after entering that does nothing (except once again ask!)  What I am doing wrong?

  Thank you

  That your network is already reached, but him dosent software LELA display you something on your safety. This means that the LELA was not able to properly synchronize with the router and its wireless settings. So in this case, you do not have to worry about this, if you want you can uninstall and reinstall the LELA software on your computer, that might solve the problem. Or of another Complitely uninstall LELA software from your computer.

• Problem with RV0042 - mask subnet/router/gateway?

  Hi guys.

  I have a DSL here in Holland. To use my RV042 VPN function, I need the router to get the IP of the DSL modem. No problem, I bought a modem that can define transparant and with dhcp-parody the modem Gets the public ip address (say 85.223.12.34).

  The thing is, I can't access the internet, or in fact any IP that isn't in the first segment of the external IP address. So I can reach 85.123.34.56, but not 86.123.34.56. So I plugged the modem to a computer, set the transparent modem and the computer got the public IP address. And you know, I have a perfect connection, and everything works. Looking at my ip information, download the provider 255.0.0.0 subnet. Im not a Networking Wizard, but it seems to me that the problem lies here. But why is my stand-alone pc able to connect quite normal, but when I connect my linksys RV042 and internal diagnostic test (ping) of the router or a computer behind the router, obtaining an ip address, I don't get anything.

  When I ping manually, I also get the message "network is not available. Ping to an IP on the same subnet (for example, 85.111.111.111) goes perfect.

  I'm obviously missing something here. My colleuge said it could be and router/gateway (currently bridge) or a NAT problem-associated device.

  Please point me in the right direction.

  Intellectual property of addidional information:

  External ip address: 85.223.12.34

  External subnet mask: 255.0.0.0

  External gateway: 217.149.196.82

  External DNS: 217.149.196.6

  Internal IP address: 172.16.0.254

  Internal subnet: 255.255.0.0

  New firmware etc.

  Thank you guys!

  What static routes you add exactly on your RV? It's funny, it works now.

  WIndows seems to accept a gateway address that is not on a connected interface.

  The first line is the rule of default gateway:
  0.0.0.0 0.0.0.0 217.149.196.82 85.223.66.38

  The second line just tells you that 85.0.0.0/255.0.0.0 is connected to the ethernet adapter that has the IP 85.223.66.38.
  85.0.0.0 255.0.0.0 85.223.66.38 85.223.66.38

  Technically, the first route should now work. There is still no route for 217.149.196.82 in the routing tables. The only route that matches the destination IP 217.149.196.82 is the first route.

  But I guess that, in your case, that default gateway with 217.149.196.82 is actually connected to the network on the side of the VP, i.e. your ISP WAN runs two IP subnets on the same network. Since this first route runs on Windows, I guess that WIndows simply tries to find the MAC address of the 217.149.196.82 on the WAN using ARP interface (i.e., it assumes that the device with 217.149.196.82 is directly connected to the WAN Ethernet) and if something is used as default gateway. Is not really consistent with the ideal IP routing, but still works...

• my router gateway userse is slow and it's always lose connection when I change my location

  How can I disable my gateway uverse router and use my linksys AC9200 instead of the gateway uverse router

  You must contact your ISP to find out if the ISP's modem is flattened. If this isn't the case, then the use of the DMZ on the ISP modem.

  If the ISP's modem has a built-in router, it is best to fill the modem. Having 2 routers on the same line can cause connection problems: link >http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm if the modem cannot be filled then see if the modem has a DMZ option and enter the IP address of the router gets the modem and put it in the DMZ modems. Disable any WiFi modem from the ISP and filters such as firewalls and other. Also check the routers DHCP IP address may be in conflict with the ISP modem 192.168.1.1 IP address. Check to see if it's the same on the ISP's modem and if the modem cannot be filled, replace the 192.168.0.1 Linksys router ou.0.254.

  Preferred method of connecting with a modem of stand-alone ISP:
  ISP modem > Linksys router<>connected devices.

  Method of connecting with a modem with integrated router which can be filled with ISP:
  ISP (bridged) modem > Linksys router<>connected devices.

  Method of connecting with a modem with integrated router which cannot be cured of ISP:
  ISP modem (DMZ) > routers Linksys IP WAN placed in modems ISP DMZ<>WRT router devices.

  DSL PPPoE configuration:
  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&VW=1&articleid=3687

  Set static IP address:
  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&VW=1&articleid=3979

  Installation of the cable:
  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&VW=1&articleid=3686

• Problems of authentication of wireless with Linksys router after the recent updates

  No authenicate password for wireless connection

  Problem solved once the computer has been restarted two times, first time we just restarted it and same problem, second time stop and started them it authenicated normally. My other computers on the network worked well once the updates, just a computer that would keep asking password of the router, if you put it in the right pair invite just, once again, if you enterd in incorrect password, it would bring a window (incorrect password). The installed updates were KB981322 KB2347290, KB975558 KB905866 KB2141007.

• Gateway gt5656 bios update

  trying to update my bios.  Gateway gt5656, download files, cleta cd computer ignores cd starts normally, double-click autoexec in download download screen requesting the update of the bios, enter 1, poster for a split second then disappears.  Help

  http://support.gateway.com/support/default.aspx

  Contact Support for gateway to the link above for advice on how to solve this problem,

  See you soon.

  Mick Murphy - Microsoft partner

• Only browsers and AVAST cannot connect to internet via ethernet. Computers on the same router via WiFi, MS update, ping cmd - all access

  Help! I'm about to commit the homicide of the computer!

  I have been troubleshooting for weeks and am now bald from ripping my hair!

  Computer: Dell Inspiron 537 s Slim Desktop  w / Pentium Dual - Core CPU E5200 @250 GHz

  Network card: Realtek PCIe FE Family Controller (checked several times, through Windows, it works correctly)

  System: Windows 7 Home Premium, 64-bit with Service Pack 1

  Router: Netgear N600 model #: WNDR3400v2

  Cable router: SBV5220 Surfboard Motorola

  Now several months ago this desktop computer once more had SOME programs lose the ability to access the internet via an Ethernet cable.

  Affected programs:

  MS Internet Explorer

  Mozilla Firefox

  Avast! Security Suite

  Work of MS Security Update

  Ping works sites (Yahoo, etc.)

  Other computers connected to this network via WiFi - no problem getting on the internet.

  Run the network troubleshooter advises all is working properly, no suggestion.

  Attempted fixes:

  Turn off all extensions on IE (but don't forget Firefox and Avast! are also unable to access.)

  Disabled all start-ups and the package process

  Restarted in Safe Mode - still not able to access.

  Ran check complete virus, then check virus run start. Minor ad-ware 'virus' not found, all corrected automatically.

  Rebooted the router and the computer to infinity and beyond! s

  Tried other computers using the same ethernet cable connected to this wireless routers cable, no problem accessing the internet.

  Disabled functions package

  Off MS Firewall

  IP Reset configuration (memory: netsh ip net reset c:\resetlog.txt - without DOUBT NOT EXACT - OF THE MEMORY.) Command worked)

  As I said, this had happened before and then miraculously fixed itself after a short period (less than 1 week). This time, no joy.

  Of course, it's one of two things:

  (1) a configuration problem I just can't find/understand.

  (2) the problem of equipment more strange, more selective, in the universe.

  Anyone? Anyone? Bueller?

  Thank you more can I possibly Express for assistance.

  You could win the lottery and have a lot of beautiful children!

  (M.) Kel

  Hello team zig - zag,

  I wanted to thank you for your help. I finally broke down and reached out to our friends at Microsoft directly for assistance. They had me a role through all the things that you suggested (again). And finally (after many hours of phone and chat discussions) came up with an answer: "* shrug * we don't know what is the problem - choose a restore point and come back to that.» What I did. This has solved the problem of internet access, but created other problems I'm trying (nothing that I have to post here, they are specific to a particular program package).

  Still, I wanted to thank you for your time and effort on my behalf. I'm very, very happy!

  All my best,

  Kel

• SPA3102 as simple FXO/SIP, no router gateway?

  Hello

  Anyone who sets up a SPA3102 as a simple gateway between the PSTN FXO line and a PBX SIP internal (asterisk or similar)?  I don't want the thing trying to act as a router; It will be on the same network segment local & subnet as the computer of PBX and just needs a trunk SIP 2-way which is actually the PSTN line.

  Would this work with just the WAN port, or maybe with two ports on the same segment & subnet connected, or who could be confused?

  Thank you!

  The f

  Hi Jeff,

  You can deploy it in Bridge mode if you do not want it acts as a router:

  Router tab > Lan Setup > Networking Service > bridge

  Kind regards

  Patrick-

• How can I connect a cisco router to the internet via a cable modem / router gateway

  I have searched here but can't find the exact answer that I'm looking. I have a switch and a router cisco 1760 2950. The router has an added ethernet wic card so I have two ethernet connections available. I would like to connect the cable modem gateway the router through one of the connections on the router, then the switch ethernet. I can't get this configuration to work. There are several different ways, I saw displayed to accomlish. DHCP, without dhcp, creating a separate network and giving the e0/0 cable an ip address in the range of addresses network gateways. None of this has worked. Can someone after the commands that must be entered on the router to make this possible?

  Hello, I'm assuming that your ISP is to give addresses via DHCP...

  And I suppose also we want to implement our router DHCP in our local network to give our PCs and laptops etc...

  So what we need to do is:

  conf t

  !

  interface e0/0

  Description # INTERNET #.

  IP access-group MY_WAN in

  DHCP IP address

  NAT outside IP

  No tap

  !

  interface e0/1

  # MY LAN description #.

  IP 192.168.1.1 255.255.255.0

  IP nat inside

  !

  IP access-list standard MY_LAN

  permit 192.168.1.0 0.0.0.255

  !

  MY_WAN extended IP access list

  allow tcp any a Workbench

  refuse TCP a whole

  allow an ip

  !

  IP nat inside source list MY_LAN interface e0/0 overload

  !

  IP dhcp excluded-address 192.168.1.0 192.168.1.99

  !

  dhcp MY_LAN IP pool

  network 192.168.1.0 255.255.255.0

  default router 192.168.1.1

  Server DNS 8.8.4.4 8.8.8.8

  In this configuration, I applied an ACL for a protection to my router and my network to allow only established connections that Ive from my LAN to return to me. Anyone who tries to open a connection to your router will be refused. Everything is allowed. But you can change this option to be more specific rather than wide.

  On your switch, if you leave all ports in the vlan 1 and have as access ports, it should work.

  Hope this helps

  Please note the useful messages and don't forget to mark resolved all questions answers. Thank you.

• DNS ROUTING GATEWAY SETTINGS?

  Hello.

  I have ESXi 6.0. 32 GB of ram, SSD, Intel 2 NIC
  One NETWORK adapter for WAN (DHCP static address of my ISP)
  A NETWORK LAN (192.186.0.1) card

  1 virtual machine running the service router, DHCP, DNS, NAT (192.168.0.1) Pfsense static
  1 virtual machine running Web/mail/shared folders (192.168.0.10) Dhcp (mac locked)
  ESXi got the static IP 192.168.0.49

  My Question is on the DNS configuration and routing in ESXi.

  During installation, the default IP for dns and gateway is set to 192.168.0.49, the ESXi host yourself.
  Is this correct?

  Should I configure dns for 8.8.8.8./8.8.4.4 OR 192.168.0.1 OR my ISP dns servers?

  Or Preferred dns 192.168.0.1 and replacement of 192.168.0.49

  Or Preferred dns 8.8.8.8 and replacement of 192.168.0.1

  And default gateway? 192.168.0.1 (on vm) OR 192.168.0.45 OR my ISP default gateway OR my ISP static ip?

  / Brian

  Looking at your Setup program.

  Let your ESXi host management IP address to be 192.168.0.49

  PREFFERED DNS: 192.168.0.1, DNS auxiliary: leave this field blank

  Default gateway: 192.168.0.1

  Now remember, you assign subnet IP, mask, DG, DNS etc to any physical NIC of your ESXi host, you set these parameters VMKernel adapter created in the operating system of ESXi. Your PFsense which is to have two interfaces, one pointing to the public network, where you have configured the ISP associated IP settings, while the other interface that points to the network internal who has private IP settings so ESXi vmkernel adapter must be configured according to private IP parameters.

  See if that helps.

• 2901 Cisco Voice gateway + 9 CUCM DECT phones

  One of our locations has 2 lines of POTS that currently have wireless DECT phones. Originally, VoIP phones are provided to be placed there but they wantto use wireless phones. We do no lack of wireless phones, as the wireless infrastructure is designed to support.

  I guess I can connect a Cisco's DECT phone to an FXS port on the 2901 and be able to integrate in the VoIP system? Are there restrictions that I need to look out for?

  This can be done. An analog phone won't have as many features as an IP phone, next to that it will work.

• MGCP Gateway error

  Hello

  I have a weired question while changing the system of IPT. I'm inter network error during the call to the mobile phone number specifically.

  My script is

  CUCM 11, 0 - MGCP - PSTN gateway

  I have 3 templates for itinerary. 1 for fixed telephony and mobile as its 8 digits, 1 international and 1 for contact details number of 3 digits. My problem is when I ask only on mobile phones, it gives me below error. Debug ISDN q931

  Carrying capacity I = 0x8090A2
  Standard = CCITT
  Ability to transfer = speech
  Circuit transfer mode
  Transfer rate = 64 kbit/s
  The channel ID I have = 0xA98381
  Exclusive, channel 1
  Display i = 'Home'
  Calling party number i = 0 x 0081, '17214490'
  Plan: Unknown Type: unknown
  Called number i = 0 x 80, '36613334'
  Plan: Unknown Type: unknown
  003772: 16:44:08.584 Aug 21: ISDN Se0/0/0:15 Q931: RX<- call_proc="" pd="8" callref="">
  The channel ID I have = 0xA98381
  Exclusive, channel 1
  003773: 16:44:09.024 Aug 21: ISDN Se0/0/0:15 Q931: RX<- disconnect="" pd="8" callref="">
  Because I = 0x82FF - error of interoperability; unspecified
  003774: 16:44:09.056 Aug 21: ISDN Se0/0/0:15 Q931: TX-> the LIBERATION pd = 8 = 0x000C callref
  003775: 16:44:09.172 Aug 21: ISDN Se0/0/0:15 Q931: RX<- release_comp="" pd="8" callref="">
  003776: 16:44:28.576 Aug 21: ISDN Se0/0/0:15 Q931: TX-> INSTALLATION pd = 8 = 0x000D callref

  If I connect to the old PBX PRI, its works very well

  any help or anyone facing the front.

  Try changing the bottom under the routing model (called Group of Transformations) for the National and Mobile calls for:

  Called Party number Type * to "'National" "

  "" Left of the Dial Plan * to "ISDN"

  Reset the gateway and call another test in the debug ISDN q931 it should show you

  Called number i = 0 x 80, '36613334'
  Plan: Unknown Type: unknown< this="" should="" be="" updated="" national="" and="" isdn="">

  Test your landline and Mobile after you made the change.

  -Terry

  Please note all useful posts

• can't make an external call with CuCM and H323 gateway

  Hi experts, I have a problem with CuCM and h323 Gateway. I use a 2811 router to make a gateway H323, CuCM server and Switch layer 2 build a VoIP LAB, this my network:

  

  and my router configuration:

  Current configuration: 2335 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  router host name

  !

  boot-start-marker

  boot-end-marker

  !

  forest-meter operation of syslog messages

  !

  No aaa new-model

  !

  !

  !

  dot11 syslog

  IP source-route

  !

  !

  IP cef

  DHCP excluded-address 192.168.1.1 IP 192.168.1.10

  !

  IP VOICE dhcp pool

  network 192.168.1.0 255.255.255.0

  option 150 ip 192.168.1.2

  default router 192.168.1.1

  !

  !

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  voip phone service

  h323 connections allow h323

  allow connections h323 to SIP

  allow connections sip h323

  allow sip to sip connections

  service additional h450.12

  Fax protocol cisco

  !

  !

  !

  vocal h323 class 1

  H225 timeout tcp establish 3

  !

  !

  !

  translation of the voice-rule 1

  rule 1 / ^ 9.

  !

  !

  voice translation-profile PSTN

  translate 1 called

  !

  !

  voice-card 0

  !

  !

  application

  Service flash aa1: its - cisco.2.0.2.0.tcl

  paramspace English language en

  paramspace English index 1

  Param aa-driver 0839959204

  paramspace location English flash:

  prefix English paramspace

  !

  !

  !

  Archives

  The config log

  hidekeys

  !

  !

  interface FastEthernet0/0

  IP 192.168.1.1 255.255.255.0

  automatic duplex

  automatic speed

  H323-gateway voip interface

  port of link voip H323-gateway 192.168.1.1

  !

  interface FastEthernet0/1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  IP forward-Protocol ND

  no ip address of the http server

  no ip http secure server

  !

  !

  !

  control plan

  !

  !

  !

  voice-port 0/0/0

  cover of the echo - cancel 32

  connection ERA opx 3100

  Description 08395959204

  activation of the caller ID

  !

  voice-port 1/0/0

  !

  voice-port 0/0/2

  !

  voice-port 0/0/3

  !

  !

  !

  1010 Dial-peer voice pots

  Service aa1

  incoming called number 08395959204

  direct line to inside

  port 0/0/0

  !

  voice pots Dial-peer 2020

  PSTN description

  translation-profile outgoing PSTN

  destination-model 9 t

  Setup progress_ind allow 3

  progress_ind enable progress 8

  port 0/0/0

  Forward-digits all the

  !

  Dial-peer voice 10 voip

  destination-model 1...

  Setup progress_ind allow 3

  progress_ind enable progress 8

  h323 voice-class 1

  session target ipv4:192.168.1.2

  DTMF-relay h245 alphanumeric

  Codec g711ulaw

  No vad

  !

  !

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  Cisco password

  opening of session

  !

  Scheduler allocate 20000 1000

  end

  I have configured the gateway h323 and attach files to router parttern on follow CUCM

  What is the problem and how to solve?

  Thanks for all the help.

  Your DP pointing CUCM is wrong, or your ÉRA OPX, depending on what you need.

  voice-port 0/0/0

  cover of the echo - cancel 32

  connection ERA opx 3100

  Description 08395959204

  activation of the caller ID

  Dial-peer voice 10 voip

  destination-model 1...

  Setup progress_ind allow 3

  progress_ind enable progress 8

  h323 voice-class 1

  session target ipv4:192.168.1.2

  DTMF-relay h245 alphanumeric

  Codec g711ulaw

  No vad

  Your DP is waiting for 1... and you send 3100, they must match.

  You might need to change the significantt numbers and entering CSS, but only you can know

  For outgoing, you are throwing 9 predot, but again, expect it in your RFP, again, change as you need.

  voice pots Dial-peer 2020

  PSTN description

  translation-profile outgoing PSTN

  destination-model 9 t

  Setup progress_ind allow 3

  progress_ind enable progress 8

  port 0/0/0

  Forward-digits all the

  You cannot transfer the numbers all send you also 9 for each call

  Change your configuration you want / need.

  HTH

  Java

  If it helps, please note

  www.Cisco.com/go/pdihelpdesk

• How to install the firmware for the router LinkSys E900 update?

  Hello

  I use Mac 10.7.5 and a few months back had bought E900 wireless router.  He has installed 1.0.03 firmware and I noticed there is a 1.0.04)is update.  I downloaded the update, which is a sync .bin file, but I don't have a CD burner, or access to a Windows machine.  How can I install the update of the firmware?

  Thanks,-Dave

  Just, simple, with your wired computer (never wireless) access the GUI of the router and perform the update of the firmware.  Just point to the .bin file and you leave.  Make sure you reset the router and reconfigure it once you're done hard.

• The WAG54G v1.2 firmware update

  I have a WAG54G ver 1.2, 4 port eth + adsl wireless router.  The last update of the firmware on the support download site is Ver.1.02.1 from 18/05/2004, which is ridiculous! (details here: http://linksysbycisco.com/EU/en/support/WAG54G/download)

  It comes to the NVA, that I installed it on the router and the lt does not have same setting of WDS, so unit is more or less useless.

  I checked the alternatives open source (wrt line), but they are all with WAG54G V2 and no support previous models v1 and v1.2

  I need to somehow pass this router to something functional.  I checked the page of GPL code as well and while ls there a WAG54g list, I think that itd for V3 routers.  So the question is:

  1 is usable on v1.2 source GPL code (I guess not)

  2. suggestions for a WDS on the router (including beta / alpha firmware) is appreciated.

  Even the GPL code will not help you because often, it does not include modem etc drivers who are not GPL depending on the brand and the pilot.

  Another good reason not to get these combos of modem/router but get a simple simple modem with a router ethernet standard that you can use on any access technology...

  I can't talk about beta firmware. At least as far as I know even more recent E4200 does not support WDS with all other brands as Linksys. And you can be sure that they will not add anything to the WAG54G. It's all just too old.

  WDS has nothing to do with the routing. WDS extends the LAN inside the network local, there are only ethernet and MAC addresses. The routing is only between routers.

  What is so complicated: it's complicated. You repeat traffic. Access points must include any traffic for repeat and which is not, which means that they must find the topology. WDS severely effects of bandwidth. WDS often only works with WEP (or static, anti-rotation key WPA). Do a little reading in the internet...

  As it was not standardized how to handle questions from topologies you will often find that a Repeater works with a gateway of the same brand. A WDS would be possible with the same brand devices