MX40 and LAN - card cannot browse the internet

Similar Questions

• The VPN user cannot browse the internet

  I recently found myself working with ASA 5505 and implementation so that remote users can connect through the VPN. In this part, I managed to cope. Users can connect and authenticate you. Once this link has been established that they can no longer browse the web. I would like to make sure they use the remote instead of the local web. I think I'm close, but I am pretty stuck. Any help would be greatly appreciated.

  ASA Version 7.2 (4)
  !
  Ex host name
  domain Ex
  activate the encrypted password
  encrypted passwd
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !

  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS server-group DefaultDNS
  domain Ex
  permit same-security-traffic intra-interface
  inside_nat0_outbound list of allowed ip extended access any 192.168.2.0 255.255.255.248
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  mask 192.168.2.2 - IP 255.255.255.248 192.168.2.7 local pool RemoteDHCP
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 524.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (outside) 1 192.168.2.0 255.255.255.248
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto-map dynamic outside_dyn_map 20 set pfs
  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-AES-256-SHA
  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  SSH version 2
  Console timeout 0
  dhcpd dns 209.18.x.x 209.18.x.x
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.2 - 192.168.1.33 inside
  dhcpd allow inside
  !

  internal strategy of Group-1
  attributes of the strategy of Group-1
  Server DNS value 209.18.x.x 209.18.x.x
  Protocol-tunnel-VPN IPSec
  value by default-field Ex
  privilege of 15 encrypted password username
  tunnel-group 1 type ipsec-ra
  General-attributes tunnel-group 1
  address pool RemoteDHCP
  strategy-group-by default 1
  IPSec-attributes tunnel-group 1
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname

  Hello

  Yes, you are right. The customer does not receive anything. Please add this "crypto isakmp nat - t" command and then connect the client. Make sure you reconnect the client after adding this command if the client is connected at the time of the addition of the command.

  If this does not work, send me the output of "sh cry ipsec his."

  Mitesh

• Cannot browse the internet from the start page. Used to be OK, not now?

  Nothing happens on this search page. It used to work fine until about a week ago

  Nothing happens.

  a your firefox profile reset everything works?

• PSAA9 satellite A100 - unable to browse the Internet

  Hello

  I reinstalled the operating system on a friends computer laptop A100, installation of WINXP pro.

  After I installed, I noticed that a lot of missing drivers so I scoured internet and downloaded most of them. The problem I have is that the ethernet connection seems to not work properly. I installed the driver on the toshiba site and hooked it up to a test network to my polytec.

  On this network to test an internet connection is available, but the laptop cannot browse the internet! I can ping other PC networking on mobile Internet sites and ping but cannot browse their IE. Other network PC cannot ping the laptop automatically obtained IP address.

  Any ideas what's happening?

  Hello!

  Have you tried another browser like Firefox? I don t use IE because Firefox is much faster and I can't get a large number of modules.

  In addition, you should try to disable the firewall on the laptop. Maybe it s blocks the internet connection or the internet browser.

  Last but not least try to use a static IP address. You can change this in the TCP/IP settings.

• Allowing internal users browse the internet

  Hello

  I have a PIX 515E with IOS 6.2. I am currently using ISA server as a proxy server to browse the internet. I would like to change this and allow users to browse the internet through the PIX firewall. This wud give me an additional IP address on the ISA server computer.

  Can you tell me what commands do I need.

  Hello

  Using the ACL (named in this case) you do the following:

  > access inside permit tcp host XXXX list any eq www

  > access inside tcp list deny any any eq www

  > ip-list access to the Interior for a whole

  .. now configure the ACL inside with a statement of the Group of access interface that is

  > group-access to the Interior in the interface inside

  (NOTE. IN THE FIRST ACL ABOVE XXXX IS YOUR IP OF ISA)

  In addition, after you set up the ACL make sure to a wr m (write to memory)

  Hope this helps-

• HP 15-f003dx: robotic sound on laptop while listening to music and browsing the Internet

  Hello

  I have a HP 15-f003dx and I have problems with the audio driver. Whenever I watch videos or listen to music while browsing the Internet, everything looks like a robot, and it's really bad. I already reinstalled the driver, updated the BIOS and tried the system restore and reformatted. Nothing else has worked.

  Here are my specs below:

  10 64-Bit Windows Home

  Processor: AMD A6 - 5200 APU with Radeon HD graphics card

  8 GB RAM

  Audio: Realtek High Definition Audio

  I'm running out of options. All the solutions to the current problem would be great, thanks.

  Hi @REL1983,

  Thank you for the update.

  I'm glad that the store has been able to solve the problem for you.

  Execution of the troubleshooter is a step I have provided, if you agree that it is your problem, you would be useful to the community by choosing accepted the solution to enable other posters locate information with greater ease.

  Thanks in advance.

• Vista Home Premium gives the message "linked to limited accessibility" and I cannot access the internet.

  I have Vista Home Premium and trying to connect to a WiFi spot, I get the message "linked to limited accessibility" and I cannot access the internet. I understand this is common for Vista and there is a fix for this problem, but want to make sure that I get the right one and can't seem to find anything referring to this issue on the Microsoft site

  Hello

  This problem happens only when connecting to a particular place for the WiFi?

  You can follow the suggestions and check out them.

  Method 1

  You can read the article.

  Message when a device on a Windows Vista-based computer uses a network bridge to access the network: "connected with limited access".

  http://support.Microsoft.com/kb/930517

  Method 2

  Disable IPv6.

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.

  NOTE: You should do this for each network connection.

  Method 3

  Temporary disable your security software.

  Disable the antivirus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Note: Software antivirus and firewall can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attack.

  Method 4

  You can reset the TCP/IP stack.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

• Error message: Windows cannot access the specified device path and the second user cannot access the internet

  Original title: I have two users on Vista. We get to the top with windows can not access the specified device path.etc. The other has no problem

  The second user cannot access the internet. Can't access window appears. The other user is not problems.

  Hi Rickravel,

  1. what type of account you use?

  2. This only happens when you access Internet?

  3. when the problem started?

  4. you remember to make changes to the computer before this problem?

  Step 1:

  You can start in safe mode with network and see if the problem occurs in the account.

  You can see the following link to start in safe mode with network.

  Start your computer in safe mode

  Note: Restart the computer to boot into normal mode.

  Step 2:

  If you use Internet explorer, then you can try to disable add ons and check if it helps:

  Run Internet explorer with no Add - ons. Steps to open Internet with no mode of modules:

  a. click on start

  (b) in the search box, type in Internet explore

  c. Select Internet (no add-on mode)

  If you were able to access the Web site without any problems, then the module may cause the error.

  You can read the following article and try the steps to activate the modules individually determine which Add - ons may be the cause of the problem.

  How the modules of the browser affect my computer?

  Hope this information is useful.

• I have 2 laptops and one desktop. Desktop & laptop are very good. 2nd laptop computer cannot access the internet. I get a message media disconnected. I tried everything please help. I use Windows XP

  I have 2 laptops and one desktop.  Desktop & laptop are very good. 2nd laptop computer cannot access the internet. I get a message media disconnected. I tried everything please help.  I use Windows XP

  Hi JessaRoy,

  · The computer connected to the network or are they computer autonomous?

  · What is the number and the model of the computer?

  · What is the service pack installed don the computer?

  · What is the full error message with the error code, that's all?

  · What are the steps you tried to solve the problem?

  Try the steps from the link below: to test TCP/IP connections by using the ping and the commands net view: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/sag_tcpip_pro_pingconnect.mspx?mfr=true

  With regard to:

  Samhrutha G S - Microsoft technical support.

• Windows 7 connects and says "Internet access", but cannot access the internet!

  Hello, please help me with this annoying problem in answering it.

  My PC connects successfully to the mobile hotspot and indicates that he gined Internet access, but when I try to browse the internet (I tried Google Chrome, Internet Explorer, and Mozilla Firefox), or use any application that needs to connect to the internet (such as online games) HE DO FACT NOT WORKING, or SAY "NOT CONNECTED to the INTERNET.

  In the time that each connected device another works perfectly.

  Please when you view this thread the RESPONSE and not SIMPLY LEAVE.

  Thank you to everyone who helps me.

  Thank you to everyone who helped or tried to help me. It if a virus blocking internet access to applications. I now come back to my PC back working.

• HP 15 laptop: laptop computer is connected to the wi - fi connection, but cannot access the internet

  Hello

  My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?

  Thanks in advance.

  Hello @jerome256,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I understand that you are having a problem with your WiFi and wanted to help you!

  You are trying to access WiFi through router?  If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router.  Check that the router is connected to the internet.  If you have more than one router, then you can ensure that you are connected to the correct router.  You can also try unplugging the router for about 30 seconds, and then reconnecting it.  Please consult the following document, as it can help solve the problem for you:

  HP PC - Troubleshooting wireless network and Internet (Windows 10)

  Please let me know if this information has been helpful by clicking the thumbs up below.

  Have a great day!

• computer keeps restarting, against all odds, while I browse the internet

  How can I determine my type of memory to change?

  My computer keeps restarting, against all odds, while I browse the internet, I have advised me to try to change the memory card, but I do not know how to determine the type of card, I need. I have a Mirus counter top, and I'm running Windows XP SP3.

  Hi paulipaul,
   
  You can take any memory card (RAM-Random Access Memory), but make sure that it should be less than 4 GB. For the shoring of RAM to the motherboard you are using, refer to the manual of the computer.
   
  More information on:
  RAM, virtual memory, pagefile and all that

• internal hosts cannot access the internet w / L2L configured tunnel

  The internal hosts behind the ASA cannot access the internet with a configured tunnel to L2L. The L2L tunnel is mounted and passing traffic correctly. However, the internal host cannot access the internet through the ASA. I think I have my NAT watered somewhere. I can't even a host statically mapped to the internet. It might be because I'm used to having a WAN IP to the external interface which differs by the CIDR block assigned by the ISP. In this case, it's all together, with the ASA outside interface occupying the first available address.

  We have been assigned a CIDR range x.x.x.64/28. x.x.x.65 is my front door and my first usable est.68, by the PSI (I guess what they utilisent.66 et.67 for internal use). External interface of the ASA est.68 and I'm trying to get NAT others. I'm Polo all DHCP clients internal and have some static entries as well. Below is the relevant NAT config. Yet once, all traffic passes above the tunnel properly, but not from inside to outside. If more information is needed, please advise.

  interface outside

  IP address x.x.x.68 255.255.255.240

  NAT-control

  Global x.x.x.69 - x.x.x.77 2 (outdoor)

  Global 1 x.x.x.78 (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 10.10.10.0 255.255.255.0

  public static x.x.x.69 (inside, outside) STATIC_NAT_EXAMPLE netmask 255.255.255.255

  internal access-group interface inside

  Route outside 0.0.0.0 0.0.0.0 x.x.x.65 1

  internal to the 10.10.10.0 ip access list allow 255.255.255.0 any

  ! Remote LAN is 192.168.10.0/24

  access-list sheep extended ip 10.10.10.0 allow 255.255.255.0 192.168.10.0 255.255.255.0

  Can you post a "show sysopt run?

  Try this command to enable proxy arp.

  No outside sysopt noproxyarp

• My Firefox browser is unable to browse the internet

  Hey there! When I use Firefox to browse the internet I just get a screen that reads "it works!" Thoughts? I'm happy to send a screenshot of the screen.

  It started when I installed the module for HTTPS Everywhere.

  Problem solved. Embarrassing, I simply relied on tools "Clear recent history" and all selected. It works fine now.

• Satellite A120 - loss of Performance after browsing the internet

  Hi all, Im currently new on Toshiba laptops, just got my first one. But this question is for my brother. There an A120 laptop with windows xp. His laptop is generally very well outside of slow down after browsing the internet for 5 minutes of the ish. Initially he sails very well, but then all of a sudden slowing down, but it's not just the internet, the laptop everything slows down, turning off takes a lot of time just like any other process. The internet works fine on all other devices, IE. other computers laptops, xbox, mobile phones etc. His ISP has confirmed that there is no problem with the internet.

  Anyone have any ideas? He has already reinstalled XP

  Who knows what's wrong there. Install CCleaner and clean OS every time before you turn off laptop.

  Might be time for a clean installation of the new OS if your brother use it for years.
  You know, we don t know what is preinstalled on it, which is running in the background and what personal configuration on this machine.