My internet connection status shows no connection

Similar Questions

• My wireless connection status shows that I am connected but I did "no internet access.

  Original title: internet connected but shows "no internet access" why?

  I have a gateway laptop and everything suddenly I can't access the internet.  My wireless connections shows that I am connected but I did "no internet access?  I tried to disconnect and reconnect, but that has not worked.  I tried troubleshooting and it says there is a problem connecting with my modem, but it is impossible because all other computers cell phones/Ipod work correctly on the same connection.  Can anyone help?

  Renee

  Hello

  You did changes to the computer before the show?

  I suggest you follow these methods and check.

  Method 1: Remove all the wireless networks, listed in the network and sharing Center.

  1. click Start and select Control Panel.

  2. open the network and sharing Center.

  3. click on manage wireless networks.

  4 remove all wireless network listed in this list.

  5 restart the computer.

  Select your wireless network and connect (if course, enter your password). Check if you see exclamation of yellow color on the bar strength wireless connection.

  If the method above does not work, proceed to the next method.

  Method 2: I suggest you try the steps from the following link.

  Wi - Fi and in Windows network connection issues.
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  If the method above does not work, proceed to the next method.

   
  Method 3: Reset the TCP/IP stack.
  
  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself: http://support.microsoft.com/kb/299357 .
  If the same problem still persists, then try the next method.

  Method 4: Perform the steps from the link to set up a new wireless connection.

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  I hope this helps!

• Internet connection with Windows XP, SP3 and Airport Extreme - the status is always "absorbing network address.

  My Airport Extreme connected my IMac immediately, but I am not able to connect on the side PC. Airport utility does not 'no matter what Airport wireless devices". When you check the status of the internet connection with PC tools, the correct network is indicated and shows an excellent signal strength. The status is: "absorbing the network address. However, nothing happens.

  Under 'Repair the wireless network connection', it shows, "Windows is taking the following steps: your IP address renewal" even once, nothing happens.

  Under hardware I show Atheros Wireless Network Adapter and the mention: "this device works correctly.

  Yet, no network connection. Any help will be greatly appreciated.

  Hello

  Keep the changes and open the wireless. For example, to disable security in the router (turn on when to managed to connect).

  You can also try the wireless in a friends house, or an Internet café to get a frame of reference for this behavior elsewhere.

  -------------------

  Wi - Fi in general.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled).

  If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Internet connection problem, error: status WAN down.

  Hello. We have a Windows 7 and a Motorola 2247-N8 wireless modem/router. Recently, our internet connection has dropped. I was able to reboot the router, but on the main login page, it says "Status WAN" is declining and the PPP username and password are empty. These two things are related? Can I do to solve this problem? Thank you.

  Thanks for the information.  Your observation of the Westell modem/router is in line with what your ISP says you: your modem is assigned an IP address by a DHCP server at your ISP.

  Your two pieces of equipment have in fact several parties.   Both of them have modems, which is the interface between you and your ISP.  Both of them have routers.  A router is required between the two networks; in your case, this is the Internet on one side and your local area network (LAN) on the other side.  Unit integrated Motorola also a wireless access point.

  You only need one of each part: a modem, a router, and a wireless access point.

  Normally, you should be able to use the Motorola device and renounce the Westell unit.  However, the unit modem Motorola seems to have a problem to connect to your ISP.  According to the User Guide, that I found for him, this unit of Motorola doesn't seem to be able to connect to the type of system used by your ISP.

  You can use parts of two devices: the modem and router Westell unit and wireless point from the Motorola unit.

  I'm going to assume that this is the User Guide for the your Motorola device--> http://www.arrisi.com/modems/datasheet/2247-n8/2247_user_manual.pdf

  Connect an Ethernet cable between your computer and one of 4 yellow Ethernet ports on the unit of Motorola.  Open a web browser and type http://192.168.1.254 in the address bar and press enter (see page 13 operating Guide).  You may or may not assign a password for the configuration utility (you should end this) as described in step 4.  Skip steps 5 to 7.

  Click the "Configure" (page 16), then click on "DHCP server".  Uncheck the box "Enable DHCP server", and then click "apply changes".  You want to disable the DHCP server in the Motorola unit because you plan to use the DHCP server in the Westell unit.

  If you already haven't, go back to the configuration menu and click 'Wireless' and set "of basic wireless settings" (p. 21), you want wireless to be activated, you want the 'Standard' to be compatible with your laptop and other wireless devices (B/G/N is the most flexible; use G or N-only if you know that all your wireless devices use the same wireless standard).  I recommend uncheck Wireless Protected Setup.  "Channel" should be 1, 6 or 11 (you may or may not need to change the channel; in general, this is necessary if you live in an area where there are many nearby wireless networks, as a residential building).

  In the "Wireless security" (p. 23) article Choose WPA2 if all your wireless devices support this standard. Otherwise, use WPA.  Don't use WEP or anything.  Do not 'hide the SSID' or "Block Wireless Bridging."  If you wish, enter a new name SSID (p. 24). If you do this, do not use your name or address in the SSID name.

  Make sure you click on "Apply changes" once you make a configuration change.

  At this point, you can exit the utility of configuration of the Motorola.

  Disconnect all connected to DSL entered the Motorola phone.

  Plug the phone cable between your wall socket and the entrance of LILY on the Westell unit.

  Connect an Ethernet cable between the port of 'Data' at the back of the Westell unit and one of the yellow Ethernet ports on the unit of Motorola.

  At this point, you should be able to access the Internet using any device connected by wifi to the Motorola unit or (b) any device connected to one of the 3 Ethernet ports yellow on the unit from Motorola which is not used to connect to the Westell unit.

  Last words:

  If you created a password to access the device configuration utility (and you should), write it down on a sheet of paper and the paper to the tape drive.

  The IP address, you need to use in order to access the configuration of the Westell unit unit is 192.168.1.1.  Write this on the same sheet of adhesive paper such as password and the Westell Westell unit.

  The IP address, you need to use in order to access the Motorola unit configuration utility is 192.168.1.254.  Write this down on the same sheet of paper as the Motorola password and stick it to the Motorola unit.

  The DHCP server in the Westell unit by default local IP addresses assignment between 192.168.1.15 and 192.168.1.47.  This should be more than enough.  You can check the IP address local to any computer by opening a command prompt window and typing in Windows

  ipconfig/all (press on enter)

  This will show you the IP addresses assigned to all NICs (wired and wireless).  You need only be concerned with IPv4 (not IPv6) addresses.

  Note that if you open a web browser and go to a site such as http://www.whatismyip.com/ , you will be able to see the IP address public attributed to your Westell modem by your ISP's DHCP server.  In this case, "public" means that all users can see at this address.  However, router Westell "cache" local to your devices IP addresses so they are not visible on the Internet.

• C55-b854 satellite shows the limited internet connection

  It shows the connection some time limited and the adapter is ok.and the internet speed is also slow.

  Hello

  You did not provide details if this happens using a LAN or WLan connection.
  I would recommend checking the two internet connections.
  In the case of this limited connection problem would only appear using the WiFi connection, then you should check the configuration.

  First of all, I would like to recommend that test you different standards WLan 802.11 (B/G/N) and different (WPA/WPA2 AES, TKIP) encryption standards

  By the way; the WLan card also shares the BT. in case you are using WLan, please keep off BT.

• Dell Inspiron 2650-system of operating Windows XP. I am unable to connect to the internet. Status: Network cable unplugged. Where did this cable located on the laptop?

  I have a Dell Inspiron 2650-system of operating Windows XP.  I am unable to connect to the internet.  Status: Network cable unplugged.  Where did this cable located on the laptop?

  I have a Dell Inspiron 2650-system of operating Windows XP.  I am unable to connect to the internet.  Status: Network cable unplugged.  Where did this cable located on the laptop?

  The network port is the port on the laptop (it is not that large - look around) that looks like a large phone connection.

  You have a router/network to connect to and a cable network to connect with?

  Look at the 'Network option' part of the poster:
  http://support.Dell.com/support/eDOCS/systems/ins2600/placemat1.PDF

• HP Color LaserJet M277n MFP: HP Color LaserJet MFP M277n CONNECTED to THE NETWORK, SHOWS NO INTERNET CONNECTION

  HP Color LaserJet M277n MFP printer, is connected to the network and I am able to print and scan. During the attempt to get the HP Web Enable services in the Web services configuration page, it displays an error: "connection error, check the internet connection".

  After you enter the IP address of the printer in the browser, I am able to detect the printer. To enable printing of HP, but unable to do so finds out the above error. Tried a lot of things including re editing of. When I check the printer, it shows the proxy settings are required / incorrect, where, as confirmed by the supplier that they use the proxy server.

  Help, please.

  Hello @JljoThomas!

  Thanks for posting and welcome to the Forums of HP!

  I understand that you have a problem of activation of the functionality of web services on your MFP HP LaserJet Pro M277n. I'd love to help you with this.

  First of all, you have the printer connected directly to a wall outlet or is a surge protector or power bar? Even if you have used a surge protector/power bar this whole time and you feel that this is not the case, please connect to a wall outlet so that we can eliminate the source of energy as the primary cause. Issues when connected to an uninterruptible power supply/Strip/surge protector power
  In this document you will see, QUESTION: questions or problems may arise when a HP LaserJet printer is connected to a UPS (UPS), a power strip or a surge protector
  ↑ This is not limited to the Laserjet printers.

  If this does not resolve the issue, we are going to let the router and unplug the power cable (NOTE: do not reset the router...), then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  If you are still unable to connect to web services after trying these steps, we can try to set a manual DNS server of your printer to connect to.

  On the front panel of the printer, press the wireless icon. Select it wireless TO get the wireless summary. Do not your IP address.

  1. on your computer, open a Web browser and enter the IP address of the printer in the address bar. This will bring up the embedded Web server (EWS) page.

  2. at the top of the page, select Networking.

  3. in the left side, select Identification network.

  4. in article for DNS, under primary (IPv4) enter 8.8.8.8, under secondary (IPv4) enter 8.8.4.4.

  5. Select Apply at the bottom of the screen.

  6. try to activate the web services again.

  If it is still unable to connect, try to enter 209.244.0.3 for the primary (IPv4) and 209.244.0.4 for secondary (IPv4)

  Hope this helps!

  

• INTERNET EXPLORER IS SHOWING MY CONNECTION SUCH AS DIAL-UP OR VPN, I CONNECT DSL

  INTERNET EXPLORER IS SHOWING MY CONNECTION SUCH AS DIAL-UP OR VPN, I CONNECT DSL

  Hello

  ·        Are you able to connect to the internet?

  I suggest you follow the steps mentioned below to configure a connection.

  a. open Internet Explorer and then click Tools.

  b. click Internet Options, and then click the connection tab.

  c. click on Setup and follow the instructions on the screen.

  Apart from that, I suggest you to return the items mentioned below.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  http://support.Microsoft.com/kb/314095

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• WRT1900AC shows connected to the laptop wireless, but 'NO internet Connection' triangle

  recently replaced EA3500 Cisco that quit smoking with WRT1900AC

  configured for the wired network OK

  will connect WIFI for android Tablet

  DOES not connect to win 7 PC... worked fine with the old router (2 years)

  reset the WRT1900AC to factory settings... allowed 2.4 and 5 ghz...

  PC sees the wireless network and connects with password, still "NO internet connection".

  any ideas?

  Thank you waltinbatonrouge

  Thanks a lot for taking the time to suggest a fix... But the WRT1900AC went back to Best Buy yesterday. Easy back, by the way.

  Oh just a parenthesis... the WRT1900ac has finally connected ok Cat5. The speakeasy speedtest showed on 100-105Mbps of download, the same as the old EA3500 seized croasse.

  So, instead, I found an EA3500 used in a store of the local computer. Reset default and he already had the latest firmware.

  The old router Cisco EA3500 used the very simple "Cisco Conect" utility.

  Forums directed me to a version EA3500 of the "Linksys WiFi Smart" utility, which was a painless and immediately picked up the wireless for laptop Toshiba.

  He ran the same features on the speedtest and connected 'excellent' on room android...

  Have a great week!

• Status icon Internet connection in the toolbar

  How to activate the Internet connection status icon in the toolbar at the bottom right of the screen?

  Hello

  I suggest you follow the steps in the link below to customize the notification area in the taskbar:

  http://Windows.Microsoft.com/en-us/Windows-Vista/remove-icons-from-the-notification-area-system-tray

  I hope this helps.

• computers shows no internet connection but can access the internet

  Lately, my internet has been slow. Also, I had problems to connect to some sites to download some updates and product registration. I'd get a message that there is no internet connection detected. That's when I noticed that the network icon would increase from 2 computers with a blue dot on them to just 2 computers. I checked my "network and sharing Center" and it showed that I am not connected to the internet (red x on the line between the network and internet connection)... I can still access the internet and navigate well. When I tried to diagnose and repair, I get this message.

  "You need to register with the provider of internet services of this network to have access to the internet" and below "connections to Web pages are currently redirected to a different Web page"

  "Click to open the Web page, if it is an Internet service provider registration page you can read the registration information."

  When I clicked and it took me to http://www.microsoft.com/en/us/default.aspx.

  I turned my modem and the new, and it seems to connect again. I just started experiencing this recently (in the last week).  Can someone help me solve this problem?

  He seemed to have solved the problem. I went into the Device Manager and disabled my network card and enabled then again. I'm also done to restore my system to the rear before the problem started then uninstalled and reinstalled NIS2011. I have not reinstalled IE9 yet. Thanks for the help

• How to make the Windows 7 network icon to show availability of internet connection? With flashing.

  How to make the Windows 7 network icon to show availability of internet connection?

  Flashing

  Hi RaDiCal007,

  Microsoft has removed the option host connection icon network; apparently drain you resources. Like you, I prefer much the icon 'flashing '.

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com

• my internet connection is showing the yellow signal

  Sometimes my internet connection is showing the yellow signal on my taskbar system, sometimes the Internet will connect automatically and normally. But sometimes Internet works after restart or stop and re acting on the system, sometimes showing red X mark the Internet Signal in bar tasks. I can't find what is the real problem on my Internet.

  Hi Vincent,.

  The yellow sign can occur if the network drivers are not installed properly.

  Method 1: Run network troubleshooting and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2: Update the NIC drivers and check if the problem persists. Check out the following link to update the drivers.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Hope this information helps.

  Answer to us if you have any questions.

• How to make the Windows 7 network icon to show availability of internet connection?

  Hello!
  Windows 7 network icon shows no availability of internet connection. Windows Vista network icon showed availability of internet connection with a globe. How to make the Windows 7 network icon to show availability of internet connection?
  Concerning

  Hello kopn,.

  Thank you for visiting the Microsoft answers community.

  The icon for your internet connection, but the animation and the color associated with the network icon in Vista and earlier versions is no design in Windows 7.
  Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Just purchased lightroom 6 boxed version, try installing and the display shows 'no internet connection' when in fact my connection is good

  Hello

  Need help desperate please

  Just purchased lightroom 6 boxed version, try installing and the display shows 'no internet connection' when in fact my connection is good

  Hi TomasB,

  Please reset the file browser & Internet hosts.

  Reset Internet Browser refer: change or reset the settings of Internet Explorer - Windows help

  • Close all windows of Internet Explorer that are currently open.
  • Open the office and then tap or click the Internet Explorer icon on the taskbar. Change your settings will affect Internet Explorer and Internet Explorer for the office.
  • Press or click the Tools button and then tap or click on Internet options.
  • Press or click on the Advanced tab, and then tap or click Reset.
  • In the reset Internet Explorer settings dialog, tap or click Reset.
  • When Internet Explorer has finished the application default settings, press or click on close and then press or click OK. You will need to restart your PC for these changes to take effect.

  Reset the hosts file

  Reference: https://support.microsoft.com/en-us/kb/972034

  Mac: How do I edit the file Hosts on Mac OS X - TekRevue

  Reference: Solutions to connection errors, activation and connection with Creative Suite and creative Cloud applications.

  Let us know if it helps.

  Kind regards

  ~ Mohit