My starter windows repeat failure of configuration and does not light

Similar Questions

• When I started my computer this morning, it ran chkdsk at startup, windows startup it goes immediately to chkdsk, it will be repeated again and again. I can boot into safe mode, but if I try to start windows normally it runs chkdsk and does not start

  Windows does not start normally, just run chkdsk again and again

  First test the hard drive to make sure it's healthy. Test the hard drive with a diagnostic utility downloaded from site of the disc mftr. or use SeaTools for BACK of Seagate. You create a bootable CD with the files you download. You will need a third party burning software to do as the free ImgBurn, Nero or Roxio. Burn as an image, not in the form of data.

  http://www.ImgBurn.com

  http://www.Seagate.com/www/en-us/support/downloads/SeaTools/seatooldreg
  http://Seagate.custkb.com/Seagate/CRM/selfservice/search.jsp?docid=201271 (how-to)

  Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  If the hard drive then passes the physical tests, safe mode:
  Start > run > cmd [Enter]
  fsutil dirty query c: (or the appropriate drive letter) [Enter]

  This will tell you if the disc is dirty or not. Then always in cmd:

  chkntfs /x c: (or the appropriate drive letter) [Enter]

  This tells Windows not not to check this drive at startup. Reboot and it should go on the desktop. Once Windows loaded, run cmd and:

  Chkdsk /f /r c: (or the appropriate drive letter) [Enter]

  CHKDSK will run through all 5 steps. After that it's over, always in cmd:

  fsutil dirty query c: (or the appropriate drive letter) [Enter]

  to see that the dirty bit is not set on this drive.
  MS - MVP - Elephant Boy computers - don't panic!

• My windows 7 hangs at startup and does not update microsoft isatap adapt #5.

  I use lenovo v570. Windows 7 just hangs up on start. IM using safe mode now. but when I check the drivers, the microsoft isatap #5 adapter has a yellow exclamation point and does not update. What should do? Help, please.

  Hello

  It's the Microsof Pnrtie on "Microsoft ISATAP adapter"

  "On a Windows Vista-based computer or on a computer Windows Server 2008, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message"

  http://support.Microsoft.com/kb/932520

  See you soon.

• Windows load with black screen and does not start after windows updates

  Original title: load windows normally screen will not continue

  I went to my computer tower and I chose to install updates when closing.  I went back later to re - turn on my computer and now it loads to the top of the black screen that gives you 5 options. safe mode, safe mode with networking safe mode command prompt, windows loads normally and finally to load windows from last known configuration that works.  Problem is that none of these options work.  they all return me to the same screen.  Help this laptop came preloaded with Win XP Media Center edition and I can't get back to work.  IM assuming I need a XP disk support center but I can't find them anywhere! HELP PLEASE SOMEONE!

  Hi Burton089,

  Your hypothesis is right. To resolve this problem, we need to repair your installation of Windows using the Windows XP disk. We recommend that you contact the manufacturer of the laptop to check if they have the Windows recovery disk.
  See perform a repair Installation
  

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Window XP professinal machine crashed and does not even not start in safe mode.

  I installed "Spybot Search and Destroy" on my Windows XP Professional machine and started the application. Received a notice of bubble that the hard drive is nearly full, and then the computer froze. Did a hard reboot and went normally up until the point when the login screen appears normally then the screen went black and nothing worked except the mouse. Do you have another hard reboot and tried to start in windows safe mode. Once again, everything is going well until the point windows should have arisen screen then black again, except this time it says xp professional SP2 safe mode window. Or something simila across the top and the bottom of the screen. I don't have my original XP disc and have no idea of what would be the product key. The computer was purchased from a former employer, at the time of the purchase by them, it was a machine under windows 2000 and they have upgraded later to XP, most likely on the internet, so no XP cd. What are my options on the recovery of XP. And if that is not possible with the lack of information do you think I can upgrade the computer to Windows 7 or should I install original version. I know that the hard drive is good because I have another old machine windows 2000 can I put the hard drive in and it will read and write from the hard drive. Problem is you can't see half of the car becase the formatting of the file is different. a majority of the data I want to save the hard drive is on the side, that I don't see in the old machine.

  Joe,

  first put your hard drive of the computer that you have questions with in the computer that works well. delete or move data from the old hard drive to the other disk to free up space make sure you have about 5 GB minimum FREE on the old hard drive. Also run a virus scan and spyware on this hard drive. Then try to start the player of ard again and see if you can return to windows.

  Good luck! Please rate me upward if you find my post helpful. Thank you!

• module of Windows install is to stop and does not immediately once I turn on the computer

  I had a problem with windows install. I have 18 updates to windows that I can not download, including windows vista sp1. After that I turned on the computer module of windows installer stops working by saying that there is a problem that caused this program to run. can someone help me?

  Hi Mbittar,

  Welcome on the site of Microsoft Windows Vista Community. Installer of Modules of Windows allows management of Windows updates (remove)

  I suggest you try these options:

  Option 1: Log on as an administrator and search for services

  Step 1: Start Search Box

  Step 2: type Services.msc

  (Provide the administrator password or a confirmation if prompted to do so.)

  Step 3: The "Windows Modules Installer" service right click and select Properties.

  Step 4: Select the general tab - make sure that the startup type is manual.

  Step 5: Right-click the BITS: select General tab - make sure that the startup type is automatic (extended), began

  Step 6: Make the update of Windows right click: select General tab - make sure that the startup type is automatic (extended), began

  Option 2: How to reset the Windows Update components? Run the Microsoft Fixit link form

  Option 3: The issue can also be caused by your security program as an antivirus or a firewall of Windows /Defender that can have conflicting settings as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.

  Option 4: You can download updates from the Microsoft Download Center or the Windows Update Catalog

   

  List no. 1), the latest version of windows updates with xxxxxx (number 6digits) KB

  Step 2) download and install each of the windows updated manually

  For more information about how to download files from the Microsoft Download Center, click the number below to view the article in the Microsoft Knowledge Base:

  119591 (http://support.microsoft.com/kb/119591) how to get technical support files from Online Services Microsoft

  For more information, visit the Microsoft Web at the following sites:

  1) Troubleshooting connecting to Windows Update or Microsoft Update issues

  2) tool for description of the preparation of updated the system to Windows Vista, Windows Server 2008 and Windows 7

  3) How to troubleshoot common Windows Update, Microsoft Update and Windows Server Update Services installation issues

  Option 5: If this problem persists check the errors in the Event Viewer log to find more information. The display of the error messages in the event viewer

  You can view the log at the time the accident occurred, or you can recreate the crash for the information and go back with the details to correlate more.

  Here is an article on what information is available in the Event Viewer Log file: http://windows.microsoft.com/en-us/windows-vista/What-information-appears-in-event-logs-Event-Viewer

  Let me know if that does or does not work. Good luck!

  Hope it will be useful.

  Thank you and best regards,

  KKS Vijay

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Satellite M50D-A-103 crashed and does not light

  Hello

  I have a Satellite m50d-a-103, which takes place in Ubuntu.

  The operating system crashed recently. I'm not sure if the laptop off really or not. But the screen is dark, and the laptop does not start when you press the power button.

  The only thing that made laptop is that the power light flashes 5 times when the switch is released (no matter how long he was supported before). There is no - screen start or anything, the screen is totally black.

  Located help here suggests I have remove the RAM, but I'm not sure it's a good idea, because I'm not sure that the laptop is off.

  What I've tried is pressed the power button for 20 seconds. I tried also pressing the - or what I guess is the reset button on the back of the laptop.

  The only idea I have now is to hope that the laptop does not work because indeed, there not turn power off and wait until the battery is empty. But I'm afraid that it will take a lot of time.

  So my questions are:

  -How can I fix?
  -How can I find out if the laptop is turned off?
  S ' it is not actually disabled, how do I disable it (it has an internal battery, so removing it will not be easy)?
  - Or is this a hardware problem? And if so, how can I find out component that could be the problem?

  Thanks for any help you can offer!

  [for some reason, I can't edit my original post]

  I couldn't find the manual for the a m50d on toshibas website, but I hurt here: http://www.manualslib.com/products/T...A-3509950.html.

  For the white flashing indicator power, it is said: "Indicates that the computer is in mode 'sleep' and that there is enough available power (mains or battery adapter) to maintain this State."

  So I guess that my initial assumption may be correct. I still don't know not how out of fashion "before" however.

  Any ideas?
  Thank you.

• My iPad has been slow and has now stopped working completely and does not light

  My iPad is a few years old (I think that the iPad 2, 32GB model A1395 2, no internet,).  For w a few weeks, it has been very slow but has now stopped completely.  I can't turn on even when connected to a power source.  Any ideas?

  Bob

  You can try to reset: hold the home and power buttons at the same time and continue to hold until the Apple appears (up to 30 seconds). If you see the Apple, you should be in business. Once the reset is complete, the Slide to Unlock screen will be displayed.

  If this does not work, you will probably want to pay a visit to the Apple Store, so they can watch. It costs nothing for looking at it. Don't forget to take a go-Genius Bar, so you don't have to wait all day...

  Good luck

  GB

• Update Windows 7 updated the guard and does not configure updates

  Original title: 2 Windows updates daily for the last 10 days

  I get 2 updates every time that I stopped for the night. The updates take anything between 3 and 5 minutes to install and the pc is turned off automatically. When I restart the pc it starts immediately configure updates and it can take anything up to ten minutes. I don't know how to access the updates of teas to see if they are fresh updates or if they the same two updates recurring constantly! This 'problem' started ten days ago.

  Click Start, type: Windows Update

  Press enter on your keyboard

  Click on the link to check updates

  A list of all the updates is downloaded

  You will be able to view the updates that must be installed, along with a description and the number of KB.

  You can then choose to go to http://www.microsoft.com/downloads and download these updates manually and install them.

  You can also click on change settings in Windows Update and click the option to download updates, but choose when to install them.

  Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• Mac mini started to freeze at sign on and does not sign on.  also has popups to allow access to keychain and other pop-up windows

  Hello, I am not a tech savvy person, so be patient with me.  I bought a mac mini, 5 months ago.  everything has been working great until 2 weeks ago.  kept popups have occurred, including Keychain Access, and many others that I've never heard of.  also, I can not connect, as the color wheel is present constantly, as if the pc is currently journal, although the color wheel rotates forever.  no connection for me.  any suggestions?

  Well, in your particlular case I would recommend take your Mac to the local Apple Store. I guess the computer is still under warrantly, so you'll all be fixed free of charge and save your time and nerves.

  Use the link below to find the store near you.

  http://www.Apple.com/retail/

• iPod started to hum and does not light

  I used a magnetic to ventous for my iPod and it stopped working and started the buzz, now it's just to show message of support from apple

  A magnet, if strong enough and quite narrow can affect the iPod's hard drive.  After removing the magnet close to the iPod, the iPod still 'buzz' when you try to start?  Try doing a Reset (reboot) on the iPod

  Learn how to reset your iPod - Apple Support  (see iPod with a click wheel)

• Windows Vista clocks works slowly and does not reset correctly when the computer is restarted.

  I can reset the clock via the server of internet time and after about an hour, he begins to lose time.  When you restart the laptop, the clock is not properly reset the CMOS.  I don't think I have battery problems since the clock loses time if connected to power or not.

  Thanks for the reply David.  I'm not sure that replacing the CMOS battery in a laptop is simple.  I'd appreciate an information change in a notebook Acer Aspire.

  Here is the link:

  How do I replace the CMOS battery in an Acer laptop
  http://www.ehow.com/how_4882009_replace-CMOS-battery-Acer-laptop.html

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Excite Pro AT10LE-A-108 - reboot and does not light

  Hello

  I excite Pro 10 model AT10LE-A-108

  After you have selected 'Power Off' option Tablet closed OK but then restarts again. Only after several attempts to "Power Off" the Tablet closes down very well.

  Any suggestions?

  Another question that was yesterday the Tablet would not turn on / restart! I had looked at footie with Bt over the internet for an hour and a half without a problem. I then closed the screen for half an hour and planned to watch another game on BT the Tablet has been totally insensitive. It would not turn back on or restart.

  This morning I tried again and it works fine.
  Could be another problem related to overheating?

  This phenomenon, I've had about three times. Before I used off I 'State aircraft '. It is ok. This may be due to programs that are in the background. No not global warming.
  If not started, I hold the Start button time longer, about 10 sec. A plug in the adapter.

  Post edited by: ladar

• How can I remove ink jets if my all-in-one is broken and does not light?

  My hp officejet pro8600 than n911g was struck by lightning.  It will turn is no longer.  I used a new cord without result.  I need to remove the ink jets, I recently installed.  How can I access them without power?

  It is possible that the printer was not fried, but the power may need to be reset.  Watch this video for sure:

  http://h20621.www2.HP.com/video-gallery/us/en/customer-care/1245172417001/fixing-your-HP-printer-when-it-wont-turn-on-or-respond/video/

  If the printer is really fried, remove the front panel to access the cartridge Board and force it to the left.  Since you printer is not repairable, you lose nothing.

• Hiss of E2 and does not light

  I loaded my E2 from one day to the next. I set the alarm, the phone rang. After disconnecting the E2, I can turn it on is no longer and there is a hissing sound from the speaker. I tried to connect again, I tried pressing the button reset and hard reset, but nothing has worked.

  I'd appreciate any help.

  I left my unplugged E2 whistling until the battery died. When I plugged it in to charge, there was no whistle, and I was able to turn it on! Unfortunately, the charge lasts less than 5 minutes. I think I'll get a new battery.

  Message relates to: Tungsten E2