NAT on Xbox problems

Similar Questions

• WRT1900AC NAT OPEN Xbox problems.

  I dove in the forums for days looking for a solution, but I can't get my Xbox to have an open NAT. I booked the IP address, port, and made sure that UPnP is enabled. What Miss me? NOTE (I did not open port 53, which causes only the router lose access to the internet for some strange reason.) Help, please!

  I think that it is a private IP address. Anything on a 192, 172 or 10 is a private IP address.  You need a public IP address which is #. ##. ###. ###

  Link >http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm

  I recommend you ask at the service of the ISP and ask questions to get a public IP address of the router in order to obtain if possible OPEN NAT.

• Linksys E3000 NAT open Xbox Live settings

  Hi all

  I recently upgraded my the WRT160n V3 to the E3000 router. I had the port to the front of my old 160n to get my game Xbox Live NAT settings to OPEN.  When I switched on the router for the new E3000, my Xbox Live settings are returned to the Medium (medium). I assumed that this would have happened since this is a new installation/router.

  Can someone help me configure my E3000 and Xbox Live so I can have my open NAT settings?  I only need to configure the Xbox 1. Any help is greatly appreciated. Thank you!!!

  The previous is large enough and generally useless for the configuration of the E3000 to facilitate capacity NAT open xbox live connections. 1 make sure you have a static IP assignment for the xbox an assignment of dhcp for the mac address of the xbox in creating or statically assigning an ip address to the xbox outside the dhcp scope, you set but on the same network / subnet of course. then go to the tab under applications and games and the prior port 3074, single port forwarding, both internal and external, to the IP address of your xbox. Name the rule openNAT or something that you will recognize. put a cheeck in the box to enable the rule and click on save settings to activate. Your xbox should now work without complaint about the need for open NAT xbox live test and gameplay should work just fine.

• Problems of NAT for Xbox a Live, AC1900 Smart WiFi router model # R7000

  I can't get NAT open for my Xbox One, it is set to moderate right now. I tried to turn NAT, filtering to open, address reservation, go wireless Ethernet, port forwarding / port triggering TCP/UDP 3074.

  Any help would be appreciated

  Yes, that's all. So, your ISP is NATing your traffic. Your situation is similar to the guy with the WiMAX. I went and found this thread.
  https://community.NETGEAR.com/T5/Nighthawk-WiFi-routers/NIghtHawk-r7000-PS4-NAT-type-strict-3-issues...

  This guy had to call his ISP and ended up paying for an address public IP NAT problems. You will need to contact your ISP and either ask a public IP address, or ask them how to configure their gateway port forwarding. Read the other thread.

• NAT on XBOX 360 with WRT150N problems

  Hey guys,.

  For some reason, we had some problems with our NAT type for our xbox. We have a good (green) connection, but the NAT type always appears as "moderate." Right now, we use the (configured for the xbox) standard wireless card to connect to our router (WRT150N).

  I tried power cycling, manually enter the IP address, mask and gateway, but nothing has worked... any suggestions?

  Generally a moderate NAT problem is due to two devices on a network running NAT.  Your router is probably related to the ISP device providing NAT service.  East - similar to the configuration of your network?

  To remedy this, you can put your modem in Bridge mode device, which will require a little research according to the make and model.

  An easier way to get around this problem is to configure your network so that your router runs only as a switch.  You will need to attach the modem to the router's LAN port and keep the unused WAN port and turn off DHCP on the router.

  If you have already taken steps to eliminate any other NAT device, you can view more details about your ISP, networking and other components and maybe get a little more help.

• NAT on Xbox Live with WRT54GS problem

  I have a WRT54GS v2 and I tried to solve the NAT problem I had whenever I have test Xbox Live.  I felt like I've done the research so much on this and I can not get it out of a moderate or strict NAT.  I did the port of release for the 88 and 3074-port, feature disabled the "block internet anonymous requests" and updated to the latest firmware and I have nothing will open the NAT.  This is the first time that I ever had a NAT problem with a Linksys router hooked up to my Xbox 360 and I want to know once and for all, what steps I must take to open the NAT.  Can someone please... Please... Please give me some instructions step by step on how to open the NAT?

  First upgrade the Firmware of the router... Download the Firmware from here , after downloading the firmware, you must update the firmware...

  Follow these steps to upgrade the firmware of the device: -.
  Open an Internet Explorer browser page. In the address bar type - 192.168.1.1
  Let the empty user name & password use admin lowercase...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Press and hold the reset for 30 seconds button.
  Then, unplug the Dungeon to be able to hold down the reset button for another Seconds.Plug 30 the power back in and hold the reset button for 30 Seconds.Release the reset button. Now, you will need to reconfigure your router...

  If your ISP is cable follow this

  If your ISP is DSL follow this

  For X - Box: click on the tab "Games and Applications" and then click the sub-tab "Port Range Forwarding"...

  (1) on the first line in the box, type Application in the Xbox, in the start box, type 88 and type of box in 88, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable...

  (2) on the second line in the box of Application in Xbox1, in the start box, type type in 3074 and end in 3074 box type, leave the Protocol as and under type 192.168.1.20 ip address and check the enable box and click on save settings...

  (3) once you return to the game to the top page, click the Security tab and uncheck block anonymous Internet requests and click on save settings...

  4) click on Setup and change the size of the MTU to 1452 and click on save settings...

  (5) now assign the IP given on your Xbox
  Go to the network settings on your X - Box, then go to the settings of IP address and select manual ip/static ip and enter in this

  IP address:-192.168.1.20 default :-255.255.255.0 gateway/gateway/router subnet mask:-192.168.1.1... Save settings...

  (6) also assign addresses dns on Xbox
  Primary DNS:-4.2.2.2... Secondary dns:-192.168.1.1... Save settings...

  (7) turn off your modem, router and Xbox... Wait a minute...

  (8) plug the power to the modem first, wait a minute and plug the router power cable, wait another minute and turn the Xbox and... test it connects...

• Windows media center xbox problem

  I'm running on windows vista 64 bit, but I have a problem when connect my xbox 360 Media Center with my pc, they detect very well, but when they come to connect it disconnects the network of xbox and my pc... Help

  Hi Jonathan Thewlis

  
  Do you get any error messages when you try to connect?

  I suggest you temporarily disable the firewall, and check if the reconfiguration of the configuration solves the problem. If you are able to communicate properly with disabled firewall, then you must configure the firewall properly connect.

   

  Don't forget to enable the firewall after troubleshooting gets completed that your computer will be at risk.

  You can also check the help on the issue links - below

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Windows-Media-Center-Extender-device

  http://Windows.Microsoft.com/en-us/Windows-Vista/demo-setting-up-an-Xbox-360-as-an-Extender-for-Windows-Media-Center

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-a-Windows-Media-Center-Extender-device

   

  You can also look at the article below and check if the information is useful.

  http://experts.Windows.com/FRMS/windows_entertainment_and_connected_home/f/49/p/38589/453405.aspx#453405

   

  I hope this helps.

• nat ASA 5520 problem

  Hi I have a Cisco Asa 5520 and I want to vpn site-to-site by using another interface with a carrier of lan to lan, the problem is when I try to pass traffic have the syslog error to follow:

  No translation not found for udp src lan2lan:10.5.50.63/44437 dst colo: biggiesmalls groups / 897
   
  LAN to LAN service interface is called: lan2lan
  one of the internal interfaces is called: colo
  
  I think that is problem with Nat on the SAA but I need help with this.
   
  Config:
   
  !
  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  eve of fw - ext 255.255.255.0 address IP XXaaaNNaa
  OSPF cost 10
  OSPF network point-to-point non-broadcast
  !
  interface GigabitEthernet0/1
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/1.50
  VLAN 50
  nameif lb
  security-level 20
  IP 10.1.50.11 255.255.255.0
  OSPF cost 10
  !
  interface GigabitEthernet0/1,501
  VLAN 501
  nameif colo
  security-level 90
  eve of fw - int 255.255.255.0 172.16.2.253 IP address
  OSPF cost 10
  !
  !
  interface GigabitEthernet1/1
  Door-Lan2Lan description
  nameif lan2lan
  security-level 0
  IP 10.100.50.1 255.255.255.248
  !
  access extensive list ip 10.1.0.0 lan2lan_cryptomap_51 allow 255.255.0.0 object-group elo
  permit access list extended ip sfnet 255.255.255.0 lan2lan_cryptomap_51 object-group elo
  pager lines 24
  Enable logging
  host colo biggiesmalls record
  No message logging 313001
  External MTU 1500
  MTU 1500 lb
  MTU 1500 Colo
  lan2lan MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ARP timeout 14400
  NAT-control
  Global 1 interface (external)
  interface of global (lb) 1
  Global (colo) 1 interface
  NAT (lb) 1 10.1.50.0 255.255.255.0
  NAT (colo) - access list 0 colo_nat0_outbound
  NAT (colo) 1 10.1.13.0 255.255.255.0
  NAT (colo) 1 10.1.16.0 255.255.255.0
  NAT (colo) 1 0.0.0.0 0.0.0.0
  external_access_in access to the external interface group
  Access-group lb_access_in in lb interface
  Access-group colo_access_in in interface colo
  Access-group management_access_in in management of the interface
  Access-group interface lan2lan lan2lan
  !
  Service resetoutside
  card crypto match 51 lan2lan_map address lan2lan_cryptomap_51
  lan2lan_map 51 crypto map set peer 10.100.50.2
  card crypto lan2lan_map 51 game of transformation-ESP-3DES-SHA
  crypto lan2lan_map 51 set reverse-road map
  lan2lan_map interface lan2lan crypto card
  quit smoking
  ISAKMP crypto identity hostname
  ISAKMP crypto enable lan2lan
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Crypto isakmp nat-traversal 20
  enable client-implementation to date
  IPSec-attributes tunnel-group DefaultL2LGroup
  pre-shared-key xxXnnAA
  tunnel-group 10.100.50.2 type ipsec-l2l
  tunnel-group 10.100.50.2 General-attributes
  Group Policy - by default-site2site
  No vpn-addr-assign aaa
  No dhcp vpn-addr-assign
  Telnet timeout 5
  !
   

  The VPN is OK? ("' isakmp crypto to show his" should show a MM_Active tunnel to the peer address ")

  Normally exempt us VPN site-to-site of NAT traffic. This could be your problem. If you can share your configuration, we can have a look.

  p.s. you should affect the question of the security / VPN forum.

• Nat SRP527W-U problem

  Hello

  I have nat rules for the troubled peripheral parameter SRP527W-U with the latest firmware 1.2.4 (003). The latest firmware 1.2.4 introduced the ability to create rules specific nat through "ACL policy rules. I try to use this 'new' not available in older versions to get my network configuration made. The configuration I want to do is to have two vlan different. In the vlan1 I want nat point_to_point interface and PC in the vlan2 I want to use Tar so each computer will be accessible via the public ip address.

  I configured two different PVC on the device we are going to say:

  ADSL_PVC0:

  Encapsulation: PAI

  multiplexing: LLC

  type of QoS: UBR

  Automatic detection VPI/VCI: disable

  virtual circuit VPI:8 VCI:35

  IP settings:

  IP: 2.2.2.2 (it isn't my real ip address that's just an example)

  subnet mask: 255.255.255.252

  Gateway: 2.2.2.1

  MTU: automatic

  ADSL_PVC1:

  Encapsulation: PPPoA

  multiplexing: VC

  type of QoS: UBR

  Automatic detection VPI/VCI: disable

  virtual circuit VPI:8 VCI:40

  PPPoA settings:

  user name: [email protected] / * /

  past: xxxxxxx

  connection: keep alive

  MTU: automatic

  in the Internet_setup_menu, I chose:

  Default system via ADSL_PVC0 route

  voice by default ADSL_PVC1 road

  After that I enabled under menu interface_setup-> LAN-> VLAN_settings two different VLANS:

  vlan1 (default vlan):

  private_lan:

  ID: 1

  subscription_type: DHCP_server_pool

  DHCP pool: DHCPRule_1 (VLAN1)

  voice: off

  Members: LAN_port1, LAN_port3, LAN_port4, SSID1

  VLAN2 (vlan public):

  public:

  ID: 2

  subscription_type: DHCP_server_pool

  DHCP pool: DHCPRule_2_public_ip (VLAN2)

  voice: off

  Members: LAN_port2, SSID2

  and I put two different rules of the DHCP:

  DHCPRule_1

  VLAN 1

  ip address local address/subnet 192.168.1.1/24

  mode DHCP: dhcp server

  GW: 192.168.1.1

  DNS proxy: enabled

  DHCPRule_2_public_ip

  VLAN 2

  local ip address/subnet 3.3.3.1/27

  mode DHCP: dhcp server

  GW: 3.3.3.1

  DNS proxy: disabled

  DNS1: 8.8.8.8

  After that, I put under menu network_setup-> nat-> global_nat:

  address translation:

  NAT: disabled

  Instead, I added this policy under nat_bypass:

  policy nat_lan

  activated: Yes

  inside the interface: vlan1

  outside interface: ADSL_PVC0

  IP address: 2.2.2.2/30

  If I try to join a pc on the lan port 1 I am able to get the ip via DHCPRule_1 configuration I can ping 192.168.1.1 gw but I'm not able to ping 8.8.8.8.

  If I try to join a pc on the lan port 2 I am able to get the ip via DHCPRule_2_public_ip configuration I ping 3.3.3.1 gw and I am ABLE to ping 8.8.8.8 and safe surfing on the web.

  Side wan I am able to reach the router via the ip address different pubblic two assigned to the PVC ADSL_PVC0, ADSL_PVC1

  If I try to activate the nat under global_nat of course, I am able to browse the web, and the device uses the public ip address of the pvc ADSL_PVC0 NAT 'myself. "

  I tried configuration multiple times and I tried to apply many different configurations "flavor", but I'm still having trouble getting the configuration made. From my point of view, there is some sort of bug related to nat or something missing in this configuration.

  Any help will be really appreciated.

  Thanks in advance for your answer.

  Hi Paolo,.

  The default mode of operation for the RPS is to have active NAT.  If the global NAT setting is disabled, then the RPS will run in mode routing only (no NAT never).

  For your configuration, leave the global NAT setting as active and create a rule to bypass NAT for traffic in VLAN 2 (effectively ensure that this traffic is routed and not translated).

  Rules-based routing policy allows you to set your local traffic PVC must use.

  Hope that helps.

  Andy

• % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection refused because of the failure of the path opposite. NAT VPN clients problems after that put 8.3.2 to level.

  I've recently updated to 8.3.2 and I have been informed of these NAT changes, but even after reading the https://supportforums.cisco.com/docs/DOC-12569 I am still unable to rectify the communication network 192.168.100.0 VPN with hosts on 172.16.1.0 and 172.16.9.0. VPN clients connect to the external interface, and I try to ping inside and the demilitarized zone, respectable 172.16.1.0 and 172.16.9.0 hosts. VPN client shows that the two previously mentioned networks such as roads of security, but still not to the ping pong.

  # sh nat

  Manual NAT policies (Section 1)

  1 (inside) to the (whole) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  2 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  3 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)

  1 (dmz), to the source (external) static obj - 172.16.9.5 interface tcp www www service

  translate_hits = 0, untranslate_hits = 142

  2 (dmz) (outdoor) source static obj - 172.16.9.5 - 01 interface service tcp 3389 3389

  translate_hits = 0, untranslate_hits = 2

  3 (dmz) (outdoor) source static obj - 172.16.9.5 - 02 interface tcp ldap ldap service

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) (outdoor) source static obj interface - 172.16.9.5 - 03 service ftp ftp tcp

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) of the source static obj - 172.16.9.5 - 04 interface tcp smtp smtp service

  translate_hits = 0, untranslate_hits = 267

  6 (inside) source static obj - 172.16.9.0 172.16.9.0 (dmz)

  translate_hits = 4070, untranslate_hits = 224

  7 (inside) to (dmz) source static obj - 10.1.0.0 10.1.0.0

  translate_hits = 0, untranslate_hits = 0

  8 (inside) to (dmz) source static obj - 172.16.0.0 172.16.0.0

  translate_hits = 152, untranslate_hits = 4082

  9 (dmz) to dynamic interface of the obj - 172.16.9.0 - 01 source (outdoor)

  translate_hits = 69, untranslate_hits = 0

  10 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 196, untranslate_hits = 32

  I think you must following two NAT config

  NAT (inside, outside) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
  NAT (dmz, external) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

  Please configure them and remove any additional NAT configuration and then try again.

• problem of controller Xbox 360 windows

  Hi Tomas.

  Please go to the Microsoft Community Forums.

  We are sorry that we are not able to access the link you gave.

   

  So, if you could answer a few questions that would help us resolve this problem:

  1. is this a wired Xbox 360 controller or wireless?

  2. do you get an error message?

  3. What is the exact problem you are facing with Xbox 360 controller?

   

  Here are some ways you can follow to resolve the problem:

   

  Method 1:

  Run the hardware and devices Troubleshooter

  Check out the link:

  http://Windows.Microsoft.com/en-in/Windows7/open-the-hardware-and-devices-Troubleshooter

   

  Method 2:

  Uninstall and reinstall the drivers for the Xbox 360

  Check out the link:

  http://www.Microsoft.com/hardware/en-in/downloads#gaming

   

  Method 3:

  You can check if the below article assist, you configure the device correctly-
  http://support.Xbox.com/en-us/games/Xbox-controller-for-Windows-Info

   

  Also you can check the link below for assistance:
  http://forums.Xbox.com/xbox_forums/xbox_support/default.aspx

   

  I hope this helps. If the problem persists, please email us with the exact details of the question and the answers to the questions above so that we can better help you.

  1. it's wireless

  2 NO.
  3. the right analog is drifting upward without touching the cushion
  I have try all methods and have no idea what to do: /.

  FOR ANY XBOX PROBLEM:

  XBox - Support
  http://support.Xbox.com/en-us/pages/default.aspx

  XBox - Contact us (support)
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)
  http://forums.Xbox.com/

• My xbox to stop 11/09 to red light E82

  I have not received one email from staff, saying that I was goin to receive another email on the details of the repair, but, so far, I have nothing.

  The bag does not help because of the stupid beta program, then, what do I do?

  FOR ANY XBOX PROBLEM:

  XBox - Support
  http://support.Xbox.com/en-us/pages/default.aspx

  XBox - Contact us (support)
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)
  http://forums.Xbox.com/

• HELP my account is blocked cannot play on my Xbox

  Everytime I try to sign my gamer tag on my Xbox n he asks me a password. I type in and it says that my email is blocked so I can't connect to my profile. My gamer tag is v o Adam and email linked to this account is * address email is removed from the privacy *. Today, I called the Xbox team to ask why I was charged £39.99 recently. We couldn't access my account as it is blocked. To this day I still don't know why it is blocked. I tried several times to perform a recovery account, but each time he said: I'm not providing enough information. It is very frustrating because it's mine, and there is no real reason why this happened. Why my account is blocked and I can unlock?

  FOR ANY XBOX PROBLEM:

  XBox - Support
  http://support.Xbox.com/en-us/pages/default.aspx

  XBox - Contact us (support)
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)
  http://forums.Xbox.com/

• look at the xbox 360 rental on computer

  Is it possible to watch rented xbox 360 movies on my computer?

  FOR ANY XBOX PROBLEM:

  XBox - Support
  http://support.Xbox.com/en-us/pages/default.aspx

  XBox - Contact us (support)
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)
  http://forums.Xbox.com/

• My xbox console

  Recently I bought some live maps 3 months and started new accounts... while playing yesterday, my pleasure was interrupted my a message saying that my console has been forbidden to play matchmaking... At the time, I was playing Halo 3, and now I am unable to play. I would like some info on how it happened and how I could get the ban lifted. I think that Iv'e done anything to violate the terms of use... But apparently, after speaking with 2 seprate xbox live pesronel, I was penalized due to complaints on my profiles... I see not just that I have spend money to play, and just because I can be better or worse than other players, I have banned because of their dislike for me... I am waiting for a response and, hopefully, a solution. Thank you for your time

  FOR ANY XBOX PROBLEM:

  XBox - Support
  http://support.Xbox.com/en-us/pages/default.aspx

  XBox - Contact us (support)
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)
  http://forums.Xbox.com/

  Information of ban Xbox LIVE
  http://support.Xbox.com/en-us/billing-and-subscriptions/account-management/Xbox-Live-console-ban

  Xbox LIVE policy on Suspensions of Console
  http://www.Xbox.com/en-us/consoleban