Need help in configuration of Proxy reverse using Apache - R12

Similar Questions

• need help with my screen has been using mouse and the screen is smaller and smaller

  need help with my screen has been using the mouse and the screen is smaller and smaller, so can't see

  Try to hold the 'ctrl' key and turn the wheel of scrolling the mouse forward to zoom, turning the scroll wheel to the rear is to zoom out.

• HP C4580 not scan to PC. I need help to configure my Netgear router please :)

  Hello

  I've read here, the threads that talk about this printer prints only not to or from a PC - my problem is that the C4580 go scan from my PC, but will not scan to PC.

  I found an answer from someone who has had the same problem earlier this year, but I do not understand what to do.

  Here's the answer:

  "I have ordered mine entering the settings from my router (Netgear) page and setting the built-in firewall rules. "The internal firewall was blocking the printer, I could print, scan using the computer, just could not scan from the printer to the computer.

  Also, I have a Netgear router, but could do with help on how to do the same thing as the person above.

  Thanks in advance for any help!

  Sorry, I don't need help after all

  It was not the router requires a configuration, it is the firewall that was a block that should be changed to "allow".

  My "all-in-one" now does everything it is supposed to do

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• Debugging - need help with configuration

  I also posted this in advanced by accident...

  I need help to my local development for CFBuilder debugging machine configuration. Developing CF applications is configured correctly, but I have problems configuring settings for debugging for CFBuilder/Eclipse. CFBuilder is installed and connected to RDS, and CF administrator is configured to debug level line. I'm running Windows 7 x 64 with ColdFusion 9 (using IIS).

  All my projects are in my "C:\Dev" folder, and each project contains a folder "www", which is the root of the web project. So, I have my projects organized like this:

  C:\Dev

  TestSite

  design

  docs

  www <-web root folder

  , I have created a ColdFusion project and he mapped directly to the folder root 'www '. In IIS, the web root folder is mapped via a virtual directory under the web site default and is accessible from "http://127.0.0.1/testsite"" "

  I have configured my RDS server that works correctly, so I can see the databases on the server. Nice. I also set up a server in the list of servers in the perspective of coldfusion and imported directly from my RDS server settings. It has the same name as my RDS Server, which is 'Server RDS Local.' I also added a URL prefix for "testsite" which is mapped to the local path: (C:\Dev\TestSite\www) and "http://127.0.0.1 \testsite. And finally, in Debug maps (preferences window), I said 'Server RDS Local.'

  Everything seems to be installed, but I can not debug. Here's what happens:

  Of the ColdFusion perspective, I click with the right button on index.cfm and select "Debug-> ColdFusion Application" the first time I do it, it switches on the ColdFusion debugging Perspective and loads of " " http://Homepage/ 'and then nothing seems to work. On the debugging tab, it shows me that he has created a new launch for my project as follows:

  TestSite

  Local RDS Server

  Model of ColdFusion

  I see my breakpoint in my breakpoints tab. But I can't seem to get any further. I can't find a way to run at my breakpoint. The home page for the current debugging session is "http://homepage/" which is something I don't understand. How CFBuilder go to the correct home page for the debug session? Maybe that's the key of.

  Hello

  Please right click on the project, and you will see an option "set the URL prefix. Allows to set the URL of your project.

  Thank you!

  Bhakti

• I need help for configuring security for my wireless again.

  Need a help for my Wi - Fi Protected Access set up again... somehow I deleted it while trying to access the networks wireless outside my house.

  original title: Wi - Fi Protected Access

  Hi dmcangus,

  See the Microsoft articles below for more information on WPA wireless security.

  Configure Security Wireless WPA for home networks

  http://Windows.Microsoft.com/en-us/Windows-XP/help/networking/configure-WPA-wireless-security

  Overview of upgrading security Wi - Fi Protected Access (WPA) in Windows XP

  http://support.Microsoft.com/kb/815485

• Need help to resolve the query by using analytic functions

  Hello
  
  I need help to solve this problem, I tried an analytical function but could not solve the problem.
  
  I have three table as illustrated below the table is filled with a flat file. The records are arranged sequentailly based on the name of the file.
  
  The first record of the game based on EIN goes to TAB_RCE
  the following records then goes to TAB_RCW
  and last save of the game based on EIN goes to the RCT table
  
  How can I make groups and
  assign a
  
  EIN * 12345 * line number * 02, 03, 04 * in the table TAB_RCW and * 05 * in the table TAB_RCT
  EIN * 67890 * line number * 07, 08, 09,10 * in the table TAB_RCW and * 11 * in the table TAB_RCT
  and so on...
  
  Thank you
  
  Rajesh
  
  TAB RCE_--------------------------------------------------------------
  LineNumber EIN FILENAME TYPE
  
  -----
  
  01 12345 ABC NCE. TXT
  06 67890 ABC NCE. TXT
  12 76777 ABC NCE. TXT
  
  -----
  TAB_RCW
  -----
  LineNumber TYPE SSN FILENAME
  -----
  02 22222 ABC RCW. TXT
  03 33333 ABC RCW. TXT
  04 44444 ABC RCW. TXT
  07 55555 ABC RCW. TXT
  08 66666 ABC RCW. TXT
  09 77777 ABC RCW. TXT
  10 88888 ABC RCW. TXT
  13 99998 ABC RCW. TXT
  14 99999 ABC RCW. TXT
  
  -----
  TAB_RCT
  -----
  NAME OF THE FILE OF TYPE LINENUMBER
  -----
  RCT 05 ABC. TXT
  RCT 11 ABC. TXT
  RCT 15 ABC. TXT
  -----

  SQL> with TAB_RCE as (
    2                   select 'RCE' rtype,'01' linenumber, '12345' EIN,'ABC.TXT' FILENAME from dual union all
    3                   select 'RCE','06','67890','ABC.TXT' from dual union all
    4                   select 'RCE','12','76777','ABC.TXT' from dual
    5                  ),
    6       TAB_RCW as (
    7                   select 'RCW' rtype,'02' linenumber,'22222' ssn,'ABC.TXT' FILENAME from dual union all
    8                   select 'RCW','03','33333','ABC.TXT' from dual union all
    9                   select 'RCW','04','44444','ABC.TXT' from dual union all
   10                   select 'RCW','07','55555','ABC.TXT' from dual union all
   11                   select 'RCW','08','66666','ABC.TXT' from dual union all
   12                   select 'RCW','09','77777','ABC.TXT' from dual union all
   13                   select 'RCW','10','88888','ABC.TXT' from dual union all
   14                   select 'RCW','13','99998','ABC.TXT' from dual union all
   15                   select 'RCW','14','99999','ABC.TXT' from dual
   16                  ),
   17       TAB_RCT as (
   18                   select 'RCT' rtype,'05' linenumber,'ABC.TXT' FILENAME from dual union all
   19                   select 'RCT','11','ABC.TXT' from dual union all
   20                   select 'RCT','15','ABC.TXT' from dual
   21                  )
   22  select  rtype,
   23          last_value(ein ignore nulls) over(partition by filename order by linenumber) ein,
   24          linenumber,
   25          ssn
   26    from  (
   27            select  rtype,
   28                    linenumber,
   29                    ein,
   30                    to_char(null) ssn,
   31                    filename
   32              from  TAB_RCE
   33            union all
   34            select  rtype,
   35                    linenumber,
   36                    to_char(null) ein,
   37                    ssn,
   38                    filename
   39              from  TAB_RCW
   40            union all
   41            select  rtype,
   42                    linenumber,
   43                    to_char(null) ein,
   44                    to_char(null) ssn,
   45                    filename
   46              from  TAB_RCt
   47          )
   48    order by linenumber
   49  /
  
  RTY EIN   LI SSN
  --- ----- -- -----
  RCE 12345 01
  RCW 12345 02 22222
  RCW 12345 03 33333
  RCW 12345 04 44444
  RCT 12345 05
  RCE 67890 06
  RCW 67890 07 55555
  RCW 67890 08 66666
  RCW 67890 09 77777
  RCW 67890 10 88888
  RCT 67890 11
  
  RTY EIN   LI SSN
  --- ----- -- -----
  RCE 76777 12
  RCW 76777 13 99998
  RCW 76777 14 99999
  RCT 76777 15
  
  15 rows selected.
  
  SQL> 
  

  SY.

• Need help to configure PP CS5.5 for multi-channel audio playback, using the M-Audio 1010LT card

  I've been hitting my head against the wall, trying to use my output channels of M-audio 1010lt card multichannel sound audio of sequence reading in first Pro CS 5.5.   It works very well in hearing CS 5.5, but not pp!  Probably I'm missing something simple in the installation program.  I configured the master audio 5.1.  Selected Delta M-Audio, ASIO in Preferences Audio Hardware, the value corresponding to the Audio output as shown here:

  

  Here is a picture of the display of sequences showing the Dolby Digital channels and 5.1 audio channels in audio levels masters appear on the right side:

  

  When I use the similar audio settings in hearing CS 5.5 the same Dolby Digital audio track plays back through my output 1010LT channels perfectly.

  What Miss me in the configuration of Premiere Pro!

  Found my problem!  It was my use of a Blackmagic capture format as I was using a BM Decklink HD Extreme card.  When I specified HDV 1080i for a pre-selection everthing worked fine reading of the chronology of the audio tracks through the M-Audio 1010LT.

• Need help to configure the VLAN on a powerconnect 5448

  Hello world

  I am currently working on 2 switches PowerConnect 5448 but I'm completely lost in configuring VLAN.

  My bow:

  

  My needs are:

  -J' have 2 different networks that need to be isolated in different VLANS

  -I want to port 11-14 to use for network backup, all others must be used for the production network.

  -This 2 networks must pass through the port 48 (fiber)

  How can I configure this kind of network on the powerconnect interface (or via telnet)?

  My understood are the following, I have to create 2 different VLAN tag all ports, switch to safe mode all ports of the entitlement each port to the VLAN voted. Am I wrong?

  How the fiber port?

  Thanks in advance for your help on this matter.

  Since your 2 VLAN need not communicate with each other, you should be able to get this working.

  The easiest way to do this would be to have your production on VLAN 1 and VLAN 2 second network.

  Assign an IP address to the switch with the command IP #.

  Assign a default gateway with the # ip default-gateway command.

  Create a VLAN 2:

  Database console (config) # vlan

  Console (config - vlan) # vlan 2

  Set 11-14 ports to access the mode for VLAN 2

  Console # switchport mode access

  Console # switchport access vlan 2

  Set 48 on trunk or general mode ports.

  Console # switchport mode Trunk

  console # permit trunk switchport vlan add 2

  You should get pretty close to a work environment. You may encounter some problem with VLAN 2 contacting 192.168.1.0, maybe just need to put it up and test.

  Here are a few links to software packages and manuals that can help.

  Firmware.

  http://Dell.to/1tz8tW0

  Manuals.

  http://Dell.to/1yqV4DJ

  Keep us on how will your configuration.

• 32L4333DG TV - need help with configuring WLAN

  I bought a flat 32L4333DG of Toshiba, but cannot configure the wireless connection.
  Help me please.

  Message was edited: assignment has been translated

  What's the problem? Have you read the instructions in the manual how to connect WiFi TV?

  There are 3 different methods to configure the WLan configuration:

  _1) easy Setup (WPS) _
  + If the AP is WPS compatible, this method can be used. +
  + WPS is a standard of the industry, designed to facilitate the wireless LAN connection and security settings. WPS automatically configures all the wireless settings. +
  + NOTE: WEP encryption is perhaps not able to configure through easy implementation. +

  _2) assisted Setup (installation using notification s AP information) _
  + Name network, authentication and encryption are decided according to the information provided by the AP. You can manually set the security key. +
  + The security key must conform to these conditions: +.
  + TKIP/AES: ASCII 8-63 or 64 Hex characters +.
  + WEP: codes ASCII 13 5 or 10 or 26 Hex characters +.
  + There's a key ID to set for the WEP encryption. +

  _3 _) manual configuration (manual entry of all parameters)
  + Some types of encryption are only compatible with specific authentication types. +
  + When authentication is an open system, only WEP or none is compatible. +
  + When authentication is shared key, WEP is compatible. +
  + When authentication is WPA - PSK or WPA2-PSK, TKIP or AES is compatible. +

  + When the inconsistent authentication/encryption pairings are detected, a warning message will be displayed and no connection attempt will be until the conflict is resolved. +

  + There's a key ID to set for the WEP encryption. +

• Hi I need help to uninstall Windows xp by using the F keys.

  My question is the same as above, I can not understand how to uninstall windows xp with the F keys or if I should go to Mode without failure before I can do like that please help me. I checked the places of response and they tell you a whole different way in this way and I tried but it won't work.  I also tried to restore my computer back before that I was thinking when I got the Virus, but that only goes so far I'm crazy to go.  Please help me I need my computer for work.

  Thank you very much

  Thank you

  auntsands50,
  Thanks for posting on the Microsoft answers Forum.  I need to get the details on your situation.  You say that you want to uninstall XP?  It will be the only way to install another operating system or use a program that will allow you to erase the hard drive.  You mention that you got a virus and you tried to do a restore.

  So my question is what are you trying finally to accomplish?  Do you want to just get a virus on your system or you want to wipe the drive and reinstall XP.

  If you want to remove a virus, then here is a link to a program free antivirus that you can use to help clean your system: http://www.microsoft.com/Security_essentials/

  If you want to restore your system to factory default then you will need to boot from your XP cd or use the OEM solutions provided with your PC.  http://support.Microsoft.com/kb/316941 Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I need help to retrieve my hard drive using the recovery of Neosmart disk (it takes days)

  To get a better perspective, I'll tell you the history of what has gone wrong.

  What happened is that the computer has a virus and it changed some coding on the computer. When this happened to that my computer wouldn't let me enter my account and the only account that I could go on was the administrator account. I tried on a few websites and the other microsoft Web sites told me to do something with the command userinit or something like that, which led to the black screen of death that I managed to fix it on my own.

  Another website told me to use the recovery disk but like a lot of people that I don't have a recovery disk, I only had a reinstallation disk that said I could fix the computer, but it would delete all hard disk that I didn't, I need the intact files because they are important to my family.

  Then I discovered on the recovery disk that you can buy from Neosmart.com and this disc is made like the original Vista recovery disk. Anyway I bought it and I clicked on "Automatic repair" and it comes up with 2 dives eligible for recovery (it says at the top) a player is 10 GB and the other is 288 GB (it says active is the 288 GB we) I clicked on repair automated on one of them, but I don't remember. Apparently fixed it (coding I guess) and I restarted but no consideration was there. He says "Please wait" for a long time, then it comes up with a single account that says "User" I click it and it says user name and password you will need to connect to a computer at school or something. I put my username and password anyway and it does not of course and it comes up with "the specified domain does not exist or could not be contacted.

  So, I went back on the recovery disk and I so I click on system restore to get my stuff back and I can put it on a previous date until the virus has arrived and I click on it, then it is said that his recovery, files, but just like that, I let him recover and he was recovering for 3 days before I came on this site and tried something but it did not work. Like I said before it is 288 GB so I guessed it would take a long time to recover only the amount of data, but it seems just silly.

  Could someone please help me with this with words that I can identify the disk recovery Neosmart.com please

  Important additional information

  I said before that I don't remember what I have fixed drive, the thing is that there might be I have set the wrong drive, but to be honest at this point, I feel like if I do a movement without knowing what it will do, im going to lose what's on that hard drive

  Important files are not for work, they are files containing family photos of many years we couldn't print on paper of good quality printing. There is no other copy of these pictures and I really want to keep them, even with my parents.

  The recovery of Neosmart disk contains the following options

  • Auto repair
  • Score editor
  • Browse/Backup of files
  • Internet browser
  • Launch the command line

  Within the Automated repair is where you can get the system restore. The others you can kind of guess, if you want to know so just ask.

  Help, please

  Thank you

  To recover the photos, you can remove the drive and it slave on another computer (you can get very cheap external envelopes) and remove your data (you have just learned an important lesson in why you need to have backups).

  Once you have saved your data, your best bet would probably be to reinstall. A good Web site for the removal of malicious software is that one.
  http://www.selectrealsecurity.com/malware-removal-Guide/

  Good luck!

• RE: router wrt310n - need help for configuring wireless security

  I can get wireless if the router is not secure, but cannot configure wpa and wireless security.  Instructions followed on linksys tutorial but still connect wirelessly if I select wpa security.   In addition, I can't find a way to change the ssid, the pages of router do not match documentation.  The version of my router is v1.  Is this obsolete, I know that there is a v2.  Any help will be appreciated.

  Please follow these steps to configure the wireless settings and try to connect to the wireless network.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Fix the Radio band to wide - 40 MHz and change the broad Channel 9 and channel Standard 11 - 2, 462 GHz... Wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WPA wireless security, encryption, select AES... Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

  IF YOU ARE NOT ABLE TO CONNECT TO THE RADIO

• Need help with configuration of VLAN SF300-24

  Hello

  Let me Preface this with the fact that networking is certainly not my point hard, so here, any help is greatly appreciated.

  I'm trying to segment on a virtual desktop on its own VIRTUAL local network infrastructure using a Cisco SF300-24 Layer 3 switch. I can get the switch to connect to the network with the assigned VLAN 1 an IP address on the subnet of the network (192.168.16.X), but I can't get anything this is set up VLAN 20 (192.168.20.X subnet) to connect past the VLAN 20 (192.168.20.254) gateway IP. The ports assigned to 20 VLAN are defined to access the mode if it matters.

  Here is a diagram to illustrate what it looks like, as there is another (L2) switch involved.

  

  So I'm not really sure what I am missing here since all settings seem simple enough.

  Hi Simon, I recommend you remove any server active directory and essentially remove all safety factors. This will give the idea of where to start.

  If you take a quite basic set, 2 Windows 7 workstations without a Firewall window activated, they both work as expected.

  It must be remembered that in firewalls, even if they are able to respond to ICMP if the request is from a different subnet, they will not be because he is recognized as a network abroad. You must know the network on these computers or make sure the computer does not care.

  You may be able to do this by simply adding additional subnets on the advanced configuration of the network card (if it does not take too much address space) as an example.

  Or well, as you have discovered that you can add routes, which is a bit heavy and inconvienent, but effective.

  -Tom
  Please mark replied messages useful

• Need help to configure VPN NAT traffic to ip address external pool ASA

  Hello

  I need to configure vpn NAT ip address traffic external pool ASA

  For example.

  Apart from the ip address is 1.1.1.10

  VPN traffic must be nat to 1.1.1.11

  If I try to configure policy nat or static nat ASA gives me error "global address of overlap with mask.

  Please, help me to solve this problem.

  Thank you best regards &,.

  Ramanantsoa

  Thank you, and since you are just 1 IP 1.1.1.11 Polo, the traffic can only be initiated from your site to the remote end.

  Here is the configuration of NAT:

  access list nat - vpn ip 192.168.1.0 allow 255.255.255.0 10.0.0.0 255.255.0.0

  NAT (inside) 5 access list nat - vpn

  Overall 5 1.1.1.11 (outside)

  In addition, the ACL crypto for the tunnel from site to site should be as follows:

  access-list allow 1.1.1.11 ip host 10.0.0.0 255.255.0.0

  Hope that helps.