NEITHER 4472 match on Labview

Similar Questions

• Image Matching with Labview or model

  Hi all!

  I am currently implementing a picture matching algorithm on two .png images (let's call them model and Photo).

  The idea is that the template contains an examply of which must be shown in a certain part of the picture.

  Model and photography have sizes of different images.

  What we want to achieve is:

  1 find the return on investment in the Photo where the model is likely to be found

  2. compare the KING with the real model

  3. get a percentage of similarity (e.g. 90% similar-> specific Match, 70 to 89 %-> accordingly Match Possible, <70%similar -="">not a match)

  Do you have ideas on how we might put implement this?

  We currently use LABView 2015 SP1 - 32 bit with the add-on of the Vision

  We had to use a modified version of the model Inspection.vi Golden (can be found) but are blocked because the IMAQ compare continues Golden Template Module return the error message attached to this post.

  Any comment on the possible debug is also welcome!

  Thank you!

  A model is *.png with info vision (for example, settings, info, etc.). You must create the model using model editor which should be installed and accessible from the start menu.

• Call the function in LabView from a DLL, and then access the global variable of DLL

  I've created a DLL in LabWindows with a function and structure.  I want to call the function from LabView and then access the overall structure.  I am able to call the function in the DLL with a "call library function node" and has access to the return value, but I can't understand how to access the overall structure.  The structure is declared in the header DLL with __declspec (dllimport) struct parameters file.

  Is it possible to access this structure without using the library of network variables?

  My guess is that you need two bytes of padding after "in_out" and another to two bytes of padding after "anin."  The reason being that ints are 4 bytes, and most of them C compilers will align on 4-byte boundaries.  The struct will naturally start to such a limit (in fact, in Windows, it will probably start to an 8 byte boundary).  If you then count bytes in your structure, you are 70 byte after "in_out."  70 is not divisible by 4, so you need 2 bytes more to reach the next 4 byte boundary.  You can also you could reorganize your struct so that "anin" follows "in_out" and this is probably the best option if it won't cause you other problems.

  Unlike most C compilers, LabVIEW compressed structures as closely as possible, without filling.  I don't know enough about the history of LabVIEW and internal parts to explain the reasons and to do this performance penalty, but, as choice of LabVIEW "endianness", it is probably a remnant of the first versions of LabVIEW that were running on the Mac.

  If for some reason you want to force your C struct to match package LabVIEW, you can use the #pragma pack (x) directive, but I wouldn't recommend that here because you can control the C and LabVIEW.

  EDIT: in the cases where it was not clear, add padding to your cluster of LabVIEW, insert appropriate size or items at the place desired in the cluster.

• NEITHER Spy works only in the development environment?

  NEITHER Spy works on LabView (executables) stand-alone applications deployed (using VISA vi), or NI Spy works only in the development environment? It might be useful for debugging of deployed applications.

  If the answer is Yes (which I doubt), OR would have to create an installer for it since currently it is no longer available as an add-on.

  Thank you

  Ed

  Edjsch,

  You can install VISA as a standalone w/o LabVIEW. Spy is not a stand-alone installer because it does nothing in itself. That's why we always package it with a driver or application software.

• Is LabVIEW 2016 fully 64-bit compatible?

  Also recently as in 2015 of LabVIEW, the 'conventional wisdom' (which, I admit, I followed myself) was "install LabVIEW to 32 bit on 64 bit Windows , unless you were really given Big stuff on a PC with a lot of memory.  I (bad?) believed that this was particularly important with device drivers and possibly with RT I also (I thought) heard that NEITHER was currently heading LabVIEW on a platform 64-bit "pure".

  I wanted to ask OR the week, but in the excitement of it all, I forgot - should now consider us install LabVIEW 64-bit on Windows 10 x 64 platforms?  What LabVIEW RT platforms, including PXI controllers?  [Hmm - I didn't follow my own advice on the Forums and do a simple Google search - just a second...]

  OK, the Web seems to say that LabVIEW 2016 has "more support for 64-bit computing".  Maybe now is the time to take another piece of my own advice and "experience" - maybe I'll build a 'pure' 64-bit system and see if I can port my LabVIEW RT code for her...

  Bob Schor

  OK, the answer to my question is "No."  NOR, we have

  • The Time Module is only compatible with LabVIEW (32 bit). Therefore, you must have LabVIEW (32-bit), even if you use a 64-bit operating system.

  Bob Schor

• Can't get the sync to android to work - articles seem obsolete

  Hi, the articles on Mozilla on sync appear to be updated. Neither does match what I see on my screen and I have the latest versions.

  I don't see a link synchronization code when I go into the menu to sync on my pc.
  I'm also going to the top right menu on my android and the sync on the next screen button has no effect.

  Banging my head against the wall now. No items match what I see on my pc screen or on my android screen.

  My android also told me that my account login details are wrong even if I am logged in using the same info on my pc.

  Help, please. Thank you

  This article contains information for Firefox 29 + desktop and android. https://support.Mozilla.org/en-us/KB/how-do-i-set-up-Firefox-sync

• Error 200428 creating task in DAQmx Base

  I wrote a basic program that captures a voltage signal, plots and written to a file, but when I run it, I get this error message:

  "Error-200428 occurred at the value passed to the control task/channels is not valid."

  I enclose a copy of my VI. At first, I do not have the VI 'DAQmx Base create a task' in the block diagram, and I was getting the above error. After a search through some documents, it seems that the problem was that I had to put the VI to "Create a task" in when you use DAQmx Base. Unfortunately when I did, I kept getting the same error.

  Y at - it something I'm doing wrong here?

  Here is my software/hardware information:

  Operating system: Mac OS X 10.11.14

  Material: NEITHER myDAQ

  Software: LabVIEW 15.0 (64-bit)

  Drivers: DAQmx Base 15 OR 15.5, 15.5 OR-488 VISA. 2 NOR-DAQmx for myDAQ on Mac OS X (all for OS X)

  AliMoradi wrote:

  I wrote a basic program that captures a voltage signal, plots and written to a file, but when I run it, I get this error message:

  "Error-200428 occurred at the value passed to the control task/channels is not valid."

  Here is my software/hardware information:

  Operating system: Mac OS X 10.11.14

  Material: NEITHER myDAQ

  Software: LabVIEW 15.0 (64-bit)

  Drivers: DAQmx Base 15 OR 15.5, 15.5 OR-488 VISA. 2 NOR-DAQmx for myDAQ on Mac OS X (all for OS X)

  Hi Ali.

  You encounter this error, because NEITHER-DAQmx Base does not support unit OR-myDAQ . You have NEITHER-DAQmx for myDAQ installed, however, that supports this feature.

  See the instructions here to confirm that the device and the pilot communicate properly:

  Get started with NOR-DAQmx for myDAQ on Mac OS X

  http://www.NI.com/Tutorial/52345/en/

• My DAQ PCIe6361 cannot be programmed through my labview8.0

  Hello

  I just bought a new DAQ PCIe-6361. Its pilot, OR-DAQmx 9.0, does not seem to match my labview v.8.0.

  I can't program my card. How could I make it work? Is there a solution?

  Thank you!

  As shown here, DAQmx requires LabVIEW 8.2 or higher. See also this post yesterday.

• cRIO-9074 to PC connection. (connectivity network limited or not)

  Hello.

  Today, I tried to connect a cRIO 9074 to my laptop.

  But MAX could not see it.

  Then I discovered that the laptop Ethernet driver was not installed. After I installed the new driver network connection appears in the status bar, but he signed limited connectivity or not.

  In addition, when I check its status as the IP address is not 0.0.0.0 even when IP Reset DIP-switch is activated.

  What can be the problem and how can I solve it?

  Thank you!

  Yes, to use the cRIO, you need the following:

  LabVIEW

  LabVIEW Real-time

  NEITHER RIO driver

  LabVIEW FPGA (Optional if you use the scan Mode)

  See "Getting Started with Compact RIO" like a good guides through all your first steps.

• Read for the acquisition of data entries are overwritten

  Hey there

  I have a Daq reading input in a spreadsheet file

  Data acquisition was told that one is supposed to have some time a loop around it and I cannot get it to run without one, so good

  But my main problem is that it means that it replaces my written file each time that the loop repeats

  He also asked me to choose the file to write in several times

  How would I go about fixing this?

  Thank you

  Yes, you can convert digital to the chain, check the attached VI. I recommend you to go through the basic materials of LabVIEW and also play with example of NEITHER which comes with LabVIEW. Remember not to use the attached example and the acquisition of data, always use separate loops.

• Data acquisition in LabView for other suppliers DAQ cards that NEITHER

  Hello

  I am a beginner in LabView programming. I have a 32 channels base PCI card DAQ (i.e. PCI-1602 of the manufacturer, ICPDAS) and I want it to interface with Labview 8.5.

  So how cards DAQ in Labview 8.5, which are manufactured by other suppliers that NEITHER? Should I DAQmx (or some other driver) for that?

  What are the other drivers/components required to access of data PCI-1602 (device) of LabView 8.5 acquisition card?

  (1602-PCI card driver are installed in my win XP and dispalyed in Device Manager).

  Please provide some tutorial above mentioned the problem to interface.

  Please guide me in this regard. Thank you

  Waqar123 wrote:

  Hello

  I am a beginner in LabView programming. I have a 32 channels base PCI card DAQ (i.e. PCI-1602 of the manufacturer, ICPDAS) and I want it to interface with Labview 8.5.

  So how cards DAQ in Labview 8.5, which are manufactured by other suppliers that NEITHER? Should I DAQmx (or some other driver) for that? You will need the drivers from the manufacturer, of the Board of Directors.  In your case, "ICPDAS.

  What are the other drivers/components required to access of data PCI-1602 (device) of LabView 8.5 acquisition card? Same as above.

  (1602-PCI card driver are installed in my win XP and dispalyed in Device Manager). Ok.  Then take you care of my 2 answers above.

  Please provide some tutorial above mentioned the problem to interface. To learn more about LabVIEW, I suggest that you try to watch some of these tutorials.

  Please guide me in this regard. Thank you

  According to what you do with the DAQ cards, they can do the job however, from experience, there are some functions that I could achieve with the cards NOR that I couldn't with 3rd-party maufacturers.  This does not mean that this is your case. However, it is worth noting that it took me a while to understand why the code has worked with a single data acquisition card (NOR) but not another (Non-OR).

  The drivers that you have installed may or may not include examples and code in VI.  They may be DLL.  If this is the case, you can write LabVIEW "Wrappers" around these functions, as it will simplify your life.  If the drivers are in the form of DLLs, and there are no examples of LabvIEW or available VI, you must read on node library function call.

  R

• NEITHER USB-9162 driver works for MAX and SignalExpress, but not for LabView

  Hello

  I looked for a solution for a while now. According to Web sites OR the NI USB-9162 is compatible with LabView 2012. I installed the last DAQmx. My hardware has been detected and is sensitive to MAX and works very well in LabView Signal Express. But it is not detected in LabView 2012. I searched the forum and not found any solution other then all uninstallation and reinstallation of any. It is quite conssuming time and would rather avoid if possible. Anyone have a solution? I wish I could appreciate.

  Tool:

  NEITHER USB-9162

  NEITHER RIO-9215

  Benjamin

  I reinstalled everything, and now I can work with it. I can't say that I was wrong on the first time, but now it works very well as well as other bugs that are now set.

  Thank you for your answers

• Match pattern does not not in LabVIEW 2009

  Hi all

  The match pattern does not not for ' [' this symbol in LabVIEW 2009] Kindly help me how to solve this problem.

  Thank you

  Sivabalan.V

  See the attached picture. Please check the response as a solution that you think best responds to your question.

  

• How to display data series changed after each step in labview gui, that is to say after the match point fantasy, after substring etc.

  Hi, I have a labview GUI that receives data serially through VISA and basically chops to the strings and realize games until I have values that I'm looking for. I have then convert Ascii string in decimal and feed the new values to a waveform. However, I discovered that some of the output values are incorrect. I checked this by pulling data through Realterm.

  Is it possible that I can see the modified data after each step in the user interface so that I can find where the problem is? I created indicators after each step, but they do not display data, I guess that its because the data is moving too quickly.

  I am very new to labview and struggled through every bit of this GUI, as none of you regular posters know. If you can suggest a solution, please know that I will probably ask more fundamental questions in order to implement your solution.

  I enclose my GUI with a screenshot of the same data through the Realterm. Basically any where you see xxxx TR TR or W xxxxW, know that it is the data between them is to say xxxx that corresponds to the data of interest. Everything else is ignored.

  I suspect that the problem lies in the string to decimal conversion and where 3 digit values increase to 4-digit values. That is, all values of less than 850 are correct but it is the maximum value is reached. My values are expected to reach 2500. Any help would be greatly appreciated.

  You have other debugging tools available to you.  You can use the run culminating to slow down the code and show you the data flowing from each wire.

  You can create a Subvi, which takes the data of each wire and written to a log file if you can review it later.

  You give not the screenshots to your message.

• Example of NEITHER RIO USRP LabView

  Hello world

  We begin to famaliarize oursevles with USRP AND 2953R. Is there an example project in LabView which is similar to the sample of streaming media project in LabView Commnuication Rx?

  Thank you very much!

  Rui Wang

  I found myself. 'S called it Simple USRP project LabView streaming.

  You may need 2014 LabView, the LabView FPGA module installed.