NEITHER SMU 7965R for emulation

Similar Questions

• Block of RAM in SMU-7965R

  I use the element of memory in my fpga code.  However, it uses a lot of fpga slices eventhough I chose the memory implementation of the issue of the memory block. I though it should use block of RAM instead of other fpga resources. The number of total slices increases I increase the amount of data in the element of memory. It seems that using slices of fpga. I joined the project in LabVIEW FPGA and FPGA VI with this post. The target FPGA is SMU-7965R. Thank you for your help

  LabVIEW FPGA needs to logic on the fpga to take care of the communication between the chip and your host, as the communication of control/light, logic of installation for the dma channel. While LabVIEW FPGA offers ease of use, there is a fee to pay. For most of the time, this cost is acceptable compared to your actual application.

• RelativeInitialX is valid for the externally triggered measures? NEITHER SMU 5122 64 MB per channel

  For example when you use the following commands

  niScope_ConfigureDigitial (with a positive delay)

  NiScope_SetAttributeViInt32 (NISCOPE_ATTR_FETCH_RELATIVE_TO to NISCOPE_VAL_READ_POINTER)

  followed by

  niScope_FetchBinary16 (loop to retrieve the data most wfmInfo)

  What will be the value of the wfmInfo.relativeInitialX before the external trigger?  It matches?  It is set to a number to indicate the outbreak did not appear until the trigger has been received and it then becomes accurate after receiving the trigger?

  I would use it to make a set FecthForever to date, but synchronized to an external trigger waveforms up to about a minute.

  It seems that the delay of release for the 5122 should be able to hande a minimum delay time of about 170 seconds (at the max rate of sampling more at lower rates), so the data I would need could all be borrowed buffers read-ahead externally triggered and properly after off-delay measurement.

  Thanks in advance for any advice.

  Greg

  In the case that you are extracting data from before trigger (extraction of data before a relaxation was produced., relativeInitialX will have the same value as absoluteInitialX.)

  Kind regards

  Nathan

• Is NEITHER-Industrial Communications for IEC 61850 covered by all NI Developer Suite?

  Hello

  I downloaded OR-Industrial Communications for IEC 61850 14.0 and tried to activate it using my serial number for NI Developer Suite. However, I was said, "the following order numbers are not valid or do not correspond to their corresponding products.

  The same serial number was accepted for activation of OR-Industrial Communications for Ethernet/IP, so I thought that I would have access to all communication, including IEC 61850 toolboxes. Is it not the case? How can I check the toolkits are covered and which are not?

  Thank you!

  Hi JKSH,

  1. the NO-Industrial Communications for EtherNet/IP is included in the Developer Suite, as mentioned JDizzle: http://sine.ni.com/nips/cds/view/p/lang/en/nid/202469

  2. the IEC 61850, DNP3 and IEC 60870 toolkit are not part of the Suite of developer.

  3. However, you can buy Electrical Power Suite Pro + amulet of usefulness of the protocols and it has the EPS Pro and IEC 61850 and DNP3.

  http://www.NI.com/download/LabVIEW-electrical-power-suite-2015/5380/en/

  4. or you can buy each (IEC 61850, DNP3 and IEC 60870) toolkit separately

• SMU, used for the measurement of current

  Hello

  I need to measure current in the range 5 to exit 10uA by a current source PIN. I would have usually connected PXI4065 on this PIN and measured current. But in this case the current to be measured is low.

  I have EMS 4130, which has high accuracy of current measurement to 200mA range (0.03%+0.02)uA.

  

  Can I use the current part of the EMS (CH1) measurement to measure current? What should I activate CV outputs (Hi = 0V) who appears in the soft front panel?

  Or just without activating the outputs I can measure the current sink. The program of flexible panel displays current measurements, but I don't know if the EMS can be used like that.

  Thank you

  Not sure NI SMEs, as I have not had the chance to use it yet.  SMU of Agilent could be used this way, so I guess with OR as well.  You must use out SMU in constant voltage source / I measure mode.  Would you say the SMU to hold the voltage at 0V, and allow current to the sink (or source) as necessary to maintain this 0V output.

• You have a mobile emulator for Android or iPhone Firefox?

  We are doing some development for mobile applications for mobile devices using different browsers and I was wondering if you have a simulator/emulator, since you have Firefox for users of mobile devices? I would be particularly interested in an emulator that runs on the test environments for the o/s of Windows group.

  Yes, you can download a Firefox for 'emulator' mobile for Windows, Mac or Linux at http://firefox.com/mobile/download/

• Proxy for waving emulator (BB WebWorks 10) settings

  Hi all

  For construction and the terminal app to order package, I am executing the command as below:

  bbwp xyzzz - buildId 10 g C:\Users\rj\Desktop\TestProject\TestProject3.zip params - params.json o C:\Users\rj\Desktop\TestProject\output

  If I will not params.json here, it won't be able to run and will be asked to provide the parameters of proxy here.

  I want to use same file for emulator while waving param.json build and packaging app by ripple. Every time, I want to build & packagae, I use open network (another way to coonect my network like dongle system) because of the proxy settings.

  Is there any way for waving too as we have to control terminal. While it would be possible to provide proxies here too, so we won't have to use another way to conncet to the network.

  Thanks in advance

  Unfortunately by the way params.json is not currently supported by Ripple build and deploy services. For now, you can use the command line to build your application.

  For the development of the BlackBerry 10, gives us a new tool to build and deploy GUI, config.xml edition, etc., which is currently available in beta. We will add in favor params.json in this tool in time for the release of gold.

  Thank you!

• Setting UID for NFC Emulation

  Hello

  I use an emulation nfc with the VirtualISO14443Part4TypeATarget class to emulate an nfc tag.

  I want to set the uid.

  I found the "distinctive sign" value in the constructor:

  public VirtualISO14443Part4TypeATarget (reminder of the VirtualISO14443Part4TargetCallback,
  String identifier,
  Byte [] historicalBytes)

  but it doesn't seem to work. It generates a random uid on each call to the constructor.

  Is there another way to set a uid for the nfc-virtual-target?

  Thank you

  Andreas

  Hello

  It is not possible to set the UID for tag/target virtual for emulation. The API gives the impression that it is unfortunately possible. See FAQ #7:

  http://supportforums.BlackBerry.com/T5/Java-development/NFC-developer-FAQ/Ta-p/1634793

  Concerning

  Martin

• Problems of SMU-5162

  Try to calibrate a SMU-5162 to the Executive 3.6.4 Calibration using the sensor Rohde & Schwarz PNR-91. I so that he sees NEITHER Max, but for some reason any Cal Exec will not see it. I have the 3 software/drivers installed which is required:

  Toolkit 3.1.0 PNR

  PNR-NI-VISA Passport 2.4.1.0

  NRP - Z LabVIEW Driver 2.32

  Any ideas what I am doing wrong?

  Thanks in advance!

  Hi Troyl,

  you use the old PNR-Toolkit and the passport of PNR-NI-VISA. To work with the new driver NI - VISA 14 +, please update your:

  PNR Toolkit to 4.9

  PNR-NI-VISA passport to 2.7.0

  Link: https://www.rohde-schwarz.com/software/nrpz/

  rsnrpz to 3.4.1.0 LabVIEW driver:

  https://www.Rohde-Schwarz.com/driver/nrpz/

  That should do the trick

  BR

  Milo

• APS Shaker and amplifier work with SMU-1071

  Recently, we bought a shaker APS 113 and 125 APS amplifier for our new research project. We want to use NI-SMU-1071 controller system to control the shaker via amplifier.

  NEITHER SMU-1071 > APS-125 amplifier > APS 113 Shaker

  APS asked us to use Spektra VCS 403 (Vibration Control System) for this case. When we tried to use this software, there is an error in "open loop". But all things related very well. Amplifier and shaker do not work.

  The seller company has no effective technical information. Please let me know your solutions, thank you.

  Again, the 1071 is just a chassis. There must be some specific cards in it and you have not yet identified these cards.

  In all cases, you will need to obtain assistance from the supplier of the custom software unless you intend to write about something else and need some help with that.

• Collection of samples for 1 d digital Wfm N Chan NSamp

  Hello

  I'm stuck in obtaining multiple samples.

  The system configuration:

  NOR SMU-1062 q

  NEITHER SMU-6341

  SCB-68 M series

  I use Digital 1 d Wfm N Chan NSample for data output. I used the digital waveform data table.

  I checked each lines with DMM, and I could only check the last sample. (dt = 4S or more).

  Data table:

  Example 0: 010 1010

  Example 1: 001 0100

  Example 2: 100 1010

  Results: line 0 (PIN 52) (1), line 1 (0), line 2 (0), Line3 (1), Line4 (0), Line5 (1), Line6 (0) - (another Question: it looks like reverse the order for me...)

  You have any suggestions to check all the samples?

  Allow me to attach my file vi.

  Thank you

  Insuk

  Hello

  I found the solution.

  I have not configured the "DAQ - mx sample clock.

  Happy Thanksgiving day!

  Thank you

  Insuk

• [fpga] Configuration of analog input or 7965R

  Hi all

  I have a card FPGA NI FlexRIO (SMU-7965R) with an adaptation module (NI 5733). I'm using Labview real-time 2012. My measurements are dominated with harmonic sound of 60 Hz, which is most likely due to the ground loop. I try to put my analog inputs (as opposed to the CSR, NRSE) differnetial mode to try to overcome the ground loop. I came across this link which explains how to configure the FPGA input channels-

  http://digital.NI.com/public.nsf/allkb/08EF26D2E9041BC6862570E0001E442E

  However, the installation program of the RIO device for my goal of opening, I found that there is no option to choose the channel configuration (as shown in the attached picture). This means that the analog channels are in differential mode by default? If this is not the case, how can I change?

  Any help will be greatly appreciated.

  Hello!

  This KB is in what regards R, not FlexRIO product line series materials. I know it's a little confusing because the 7965 has an indicator of 'R' at the end of the model name, but the R simply it is a product with an FPGA that is programmable by the user.

  Unfortunately, the adaptation modules FlexRIO 573 x are all only ended then we will not be able to change to the differential. What is the frequency of the signal you're trying to measure? Another option would be to set the 5733 coupling AC mode, which would give the frequency response following, dramatically eliminating any sound below 10 kHz.

  

• NW238AA: Enter the program steps on an emulator of 30 HP b

  I'm a fan of HP since the HP-25 and if I have a HP 48GX-too, the weeks I bought a HP 30 b, only to "recycle" in a WP-34s.
  But before I do, I wanted to learn more about all the features of the new "business professional", for example, the difference between an old RPN stack and the stack-RPL (with an additional registry entry of 30 b) and: I want to write short, a little sophisticated programs.

  To use these programs more far, I was happy to find the download URL for HP-30 b-Emulator (© 2009 Version 2012 12 10 Rev: 19045).
  Although STI there is an "Emulator Help" available, I can't find it, how to manage a [shift-hold] [...] via the PC keyboard to enter the programming commands of the upper button 4-lines, e.g., Lbl, call, Stop, R/S, RTN and the wonderful SOLVE.

  Thank you for helping me to deal with this problem!

  -ki wrote:
  

  without more Question:

  I can't translate your note "caps-lock key is stupid" (in German)

  Can you please express this sentence in several other (English) words?

  Thank you and best regards!

  I think it was stupid to programmers to use the key for emulator equivalent to shift keyboard caps lock.

  The shift of the keyboard button is generally used, and for the emulators with several SHIFT CTRL or Alt is used to shift the second function (for example on the 35s emulator the shift of the keyboard is orange calculator shift and Ctrl is calculator blue shift).

  Kind regards.

• Channel of the DAQ (SMU-4498) task order

  I have an SMU-4498 for which I generate an acquisiiton task programmatically. When the task is created channel order is not necessarily in ascending order of channel number.

  My question is if the DAQ card will return the data in the order in which I defined the task or channel order?

  Thank you

  It seems that the answer is that channels must be specified in the order, when creating a task.

• Can you have SMU 1062 q turn on without using the power button

  I use a q SMU-1062 for a test project that will take place inside a protective case.  The power button on the chassis will be covered by a plate on the protective case that make it boring and difficult to switch on using the power button on the chassis.  The chassis will be plugged into a power strip of travel - lite which is mounted in the case.  Is it possible that I can have the power to frame on when I turn on the power strip?

  I found another route.  In the controller BIOS, I changed the parameters of loss of AC power to TURN on after that AC is returned.  This allows me to use the power strip in my configuration to control the electric network distributed to the controller.  The following steps will describe how I got this.

  1. Power of the SMU-8115 controller.
  
  
  2. A message will appear on your screen, press to enter SETUP
  
  
  3. Select 'Remove' (quickly, because you don't have a lot of time before the window disappears and the controller continues to load normally.)
  
  
  4. This will open the main Menu of the BIOS
  
  
  5. Select the Advanced tab (use the arrow keys to highlight the selections and the different tabs, select a setting change with 'enter'
  
  
  6. Select > Configuration power and rest
  
  
  7. Change the configuration to power on when power is restored.

  The controller can be normally close by using the start menu, and "shut down".

  Start button / stop of the chassis is still capable of turning the power on to the controller, but now when I shut off the AC power strip and then return power, get the controller chassis.