Network connections on the control panel

Similar Questions

• Connection of the control panel LCD of Tecra TE2000

  Have a problem with the entire monitor as there are two sets of cables from the lcd panel, we have a sockett and other two wires (black and white) are equipped with an individual connects the microphone. I tried to find a manual anywhere, but could not. Can anyone advice on this problem of mounting?

  Where on the motherboard is the connector corresponding to these two wires?

  Thank you very much

  bluestride

  Hello

  These two wires (black and white) belong to the WLAN antenna and must be connected to the wireless network card. For this model of laptop wireless network card is optional and I don't know if the card is inside.

  Sticker WLAN is placed in the lower corner of your laptop?

• My Vista compupter is slow and I cannot open the control panel

  I need to know what to do the comp is so slow the last few days and I can not connect to the control panel

  Hi diannaRasmussen,

  You have made any changes to your computer recently?

  You get the error message while opening the control panel?

  I suggest you follow the given method and check if it helps.

  Method 1: Please follow the steps in the link below to optimize Windows Vista.

  Optimize Windows Vista for better performance

  Method 2: Alternatively, you can try to perform a clean boot.

  How to troubleshoot a problem by performing a boot in Windows Vista or in Windows 7 NOTE: Make sure that roll you back changes to Normal Mode after the clean boot troubleshooting

   

  Method 3:  You can perform an analysis of checker (SFC) to file system to check on the corrupted system files.

  Please follow the steps in the link below city to make the SFC scan;

  http://support.Microsoft.com/kb/929833

  I hope this helps.

• another computer will connect to the internet. Nothing in the control panel

  Unable to connect to the internet on another computer. There seems to be no option in the control panel and none under the heading network. I have a Vista Home Basic for over 3 years and this is the first time I had this type of problem

  Are you can advise me on other measures I can take or if you stop rather giving advice that are ok as long as I know don't not to wait that all other responses. Thank you

  A response may take 10 minutes or 10 hours here. We are not employed by Microsoft.

  These are public Forums, which are only driven by Microsoft.

  "Always waiting to be part of sfc you mention so is unable to launch the scan.

  If the SFC does not start, perform the following step:

  If you do not have a DVD of Microsoft Vista, borrow one from a friend.

  Read this tutorial on how to do a repair installation:

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  See you soon.

  Mick Murphy - Microsoft partner

• HP plotter designjet 510 appears as ready in the control panel, but is not drawn. Plotter is shown connected to USB003. Any ideas?

  I am running windows vista 64-bit. I also have downlaoded and installed service pack 1 or 2 - I forgot. But now, even though I see the tracer in the control panel---> windows printer as "ready", I can't draw anything. The abacus is silent. When I click on the print status (the little icon on the bottom right of the screen), it displays the status of trace as error.

  Any ideas?

  Hi Moussa,.

  Thanks for posting your query in Microsoft Community.

  According to the description, you are facing problems with printing through HP Plotter DesignJet 510 and receive the status of tracing as error. To help you to propose measures to solve the problem, I would appreciate if you could answer the following question:

  Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: You can run the Microsoft Fixit article and check if that helps.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

   

  Method 2: If the method above does not help then you can follow the steps in the HP tool specially for HP devices.

  Try the HP Print and Scan Doctor

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c03286146

  Alternatively, you can contact HP Support for help on the issue:

   

  HP support

  http://WWW8.HP.com/us/en/support-drivers.html

  Hope this information helps.

  Let us know if you encounter problems under Windows in the future. We will be happy to help you.

• Re: The network connection to the printer has been lost.

  I'm having the same problem with a HO Photosmart 5520 and win 10. The solution to this annoying problem is far too complex and time consuming. Instead, it should be an option just to cut the sound notificaiotn.

  Welcome to the HP community @janhoza!

  I came across your post regarding your printer lost network connection and wanted to pop in to help.

  Through your message, we don't have the option to disable the notification. But I think that we can solve this problem by simply assigning a static IP address. Here are the steps:

  • Get the IP address of the printer, you can touch the 'Wireless' icon on the Control Panel printer to get the IP address.
  • Type the IP address in your web browser to get the EWS page on your computer printer.
  • Go to the 'Network' tab - click on "wireless (802.11), and then click «network address (IPv4)»»
  • Click on the box that says "Manual IP", then click "Propose an IP address manually" to give an IP address manually to your printer.
  • Click on the radio button that says 'Manual of the DNS server' and under manual type favorite 8.8.8.8 and manual replacement enter 8.8.4.4 (it is Google's DNS server address)

  Let me know if this helps. Good luck!

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• Activation of Bluetooth via the control panel in Vista

  I have Sprint everything data incrusive service and a new blackberry phone.  I'm trying to set up as a bluetooth device to access the internet on my Vista laptop.  For some reason, I can't do "recognize" to each other.  My phone does not recognize my computer as a bluetooth device and my computer does not recognize my phone as a bluetooth (from the control panel option) device.  Can someone please tell what I am doing wrong?  What step am I missing?  Is there some sort of card, I need to make this work?

  Thanks for your help!

  ReeAnn

  Hello

  To add a few options to Ajay K fine tips.

  Hardware devices not detected or does not work - a Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Add a BlueTooth device to your computer
  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

  Set up a Bluetooth compatible device
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device

  The problems with Bluetooth devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

  How to set up a Bluetooth connection
  http://www.vista4beginners.com/how-to-setup-a-Bluetooth-connection

  The Bluetooth item in Control Panel on a Windows Vista SP2 computer does not
  as expected when you click on the element - for Windows 7 this check manually
  http://support.Microsoft.com/kb/960531/en-us

  If you need drivers try the support site for the manufacturer of your system and/or the site of the manufacturer of the real device.

  BluetoothView is a small utility that runs in the background and monitor the activity of Bluetooth technology
  devices around you. For each detected Bluetooth device, it displays the following information:
  The device name, address Bluetooth, Major Device Type, minor device Type, first detection time,
  Last detection time and more. BluetoothView can also warn when a new Bluetooth device
  is detected, by displaying a balloon in your bar tasks or playing a little beep. -FREE
  http://www.NirSoft.NET/utils/bluetooth_viewer.html

  BluetoothCL is a small console application that transforms all differential of bluetooth devices detected in
  the standard output. For each Bluetooth device, the following information is displayed: MAC
  Address, name, Major Device Type, minor device Type and possibly the name of the company of
  the device (if the external file of MAC addresses - oui.txt is provided) - FREE
  http://www.NirSoft.NET/utils/bluetoothcl.html

  ---------------------------------------------------------------------

  Change settings for a Bluetooth compatible device
  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device

  Add a Bluetooth device to your computer
  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

  Add a Bluetooth device or other wireless or network device: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-or-other-wireless-or-network-device-frequently-asked-questions

  ---------------------------------------------------------------------

  More information of possible interest to some:

  What is a Bluetooth personal area network (PAN) network?
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-a-Bluetooth-personal-area-network-Pan

  Connect to a Bluetooth personal area network (PAN) network
  http://Windows.Microsoft.com/en-us/Windows-Vista/connect-to-a-Bluetooth-personal-area-network-Pan

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• HP Officejet 4500 wireless printer does not appear on the control panel

  My HP Officejet 4500 wireless printer does not appear on the control panel.  How to fix it.  I have a laptop Toshiba and Windows 7 Home Premium OS.  Help, please.    rwillm

  Hey,.

  Thanks for the update, rwillm.  It seems that the installation of the printer can be a little messed up.  If the printer software is always installed, but simply lacks the printer, then I would advise to do a little cleaning before choosing to add the printer back.

  • Make sure that the printer is deleted from the file devices and printers
  • Click on one of the remaining printers folder
  • Select the properties of the print server at the top of the window
  • Click the tab drivers
  • Remove all drivers in this window for the Officejet 4500

  Also check in the Device Manager to verify that there is no mention of remaining of the 4500.

  • Click on the start menu
  • Right click on computer
  • Select manage in the list
  • Click Device Manager in the list of questions on the left side of the window that opens
  • Click the view at the top of the menu, and then select Show hidden devices
  • Remove all references to the 4500 in the list of devices

  After making sure of the device is gone, I recommend bike devices in the power circuit: router, computer and printer.

  * Make sure the printer has a valid IP address after switching back on and is connected to the same network as your PC before adding the printer.

  If the IP address and SSID are good for the printer, then try to add the printer with the printer software, you have installed.

  • Click on the Start Menu
  • Click on all programs
  • Open the HP folder
  • Open the folder for the series of the Officejet 4500 G510
  • Select Add a device option

  Let me know how it goes,

  Jason

• I can't get rid of Highlightly even though I disabled in the extensions and uninstalled in the control panel. (windows 7 pro)

  Highlightly does not appear in the control panel more since I uninstalled it. I disabled the extension in the Add-ons. He however keeps popping up. I have windows 7 pro 64-bit.

  Is there an action actually uninstall Highlightly your list of extensions instead of disable?

  One thing I would recommend is that make you a Reset of Firefox. The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  
  Note: This will make you lose all the Extensions and preferences.

  • Sites Web open is not recorded in less than 25 versions of Firefox.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  To be sure that he's gone completely, make a check of malware with some malicious programs, analysis of the programs on the Windows computer.
  
  Please scan with all programs, because each program detects a different malicious program.
  
  All of these programs have free versions.

  Make sure that you update each program to get the latest version of their databases before scanning.

  • Malwarebytes' Anti-Malware:
    http://www.Malwarebytes.org/MBAM.php
  • AdwCleaner:
    http://www.bleepingcomputer.com/download/adwcleaner/
    http://www.Softpedia.com/get/antivirus/removal-tools/AdwCleaner.shtml
  • SuperAntispyware:
    http://www.SUPERAntiSpyware.com/
  • Microsoft security scanner:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx
  • Windows Defender: Home Page:
    http://www.Microsoft.com/Windows/products/winfamily/Defender/default.mspx
  • Spybot Search & Destroy:
    http://www.safer-networking.org/en/index.html
  • Kasperky free Security Scan:
    http://www.Kaspersky.com/security-scan

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • Utility anti-rootkit TDSSKiller:
    http://support.Kaspersky.com/5350?El=88446

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked

• I can't change anything in the control panel. My computer says I may have not sufficient permissions to access the item.

  We have tried everything we can think of changing the time in our computer.  Whenever we click on the small box in the lower right corner, he says - "Windows cannot access the specified device, path or file.  May not permissions to access you the item.  In addition, we are unable to add or remove programs or making changes through the control panel.  Help

  All the problems you describe are problems that could occur if the user that you are connected without administrator privileges.  The quick check of administrator privileges must right click on the button 'start '.  If "Open All Users" is one of the choices that appear, then you have administrator privilege.  Otherwise, you must connect to your machine like the built-in 'administrator' or a user in the group "Administrators".

  Assuming that you have administrator privileges, things get more complicated.  User rights can be granted or denied to any user - even administrators - by group policy.  If you are an administrator and you have XP Pro, then you might be able to check or change the user rights by using the Group Policy Editor (from-> Run-> "gpedit.msc").  Search in the:

  Computer configuration-> Windows settings-> security settings-> local policies-> user rights

  path.  One of these user rights is "Change the System Time".  If your XP Pro machine was never part of a domain, I would consider also running a program anti-malware on your system.

  If you have XP Home Edition, you don't have the Group Policy Editor.  You will need to check / adjust / modify your user rights by using the command line program "NTRights" provided with the Resource Kit.  Problems like that with XP Home would raise my suspicions that you have a malware infestation.

  'How to set user rights to logon using the NTRights utility'

  <>http://support.Microsoft.com/kb/315276 >

  HTH,
  JW

• No icon of Bluetooth device in the control panel of my Windows xp sp3

  I can't install the bluetooth mobile phone because there is no Bluetooth device icon in the control panel. I use Windows xp sp3. Can someone tell me what I need to do?

  Hi naturalmente.

  What is the number and the model of the device you are trying to connect?

  Check the conditions below are true:

  1. If there are several Bluetooth devices connected to your computer, temporarily remove the devices you want to solve not. If there are other USB devices, try to remove all USB devices that you do not have to be installed during the troubleshooting process. If you have several devices that are connected using USB, this can interfere with a Bluetooth transmitter/receiver.

  2. check that the Bluetooth device that you want to solve is turned on and that it is enabled.

  3. check the status of the Bluetooth support service:

  a. to open the snap Microsoft Management Console (MMC) for Services in Windows XP, click Start, click Run, type services.msc and click OK.

  b. double-click the Bluetooth Support service.

  c. If the Bluetooth Support service is stopped, click Start.

  d. in the startup type list, click Automatic.

  e. click the log.

  f. click Local System account.

  g. click OK.

  h. If you are prompted to restart the computer, click Yes.

  4. search for the parameters below:

  a. right click on the Bluetooth in the notification area icon and then click on view the Bluetooth settings.

  b. on the Options tab, click to select the discovery of the Tower on the checkbox and then click on apply.

  c. to enable Bluetooth devices to connect to your computer, click to select allow them Bluetooth devices to connect to this computer check box and then click OK.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Help! I can't access the control panel

  Help, please. I can't access the control panel, it ask me to the user and the password but I don't remember to have them change! I tried with admin/admin, but nothing, I tried to reset with buttom for 5 seconds but nothing... I'm desperate!

  Linksys WAG320N

  Press and hold the button of reset for 30 seconds, then release it.  Wait 10 seconds and cycle power to the router.  Now connect to 192.168.1.1 username "admin", password "admin".  I'm sure that the WAG uses these passwords.  Try now.

• remove the update install Q How to uninstall this stupid thing, the usual method of use of the Control Panel does NOT work

  I tried for hours and hours to remove the program called InstallQUpdater. usually, I go to the control panel and click on uninstall, then find the program, click the program, and then click on uninstall. I the image appears saying "preparing to uninstall" later I program pop up asking if I want to cancel because it is a source of the United Nations identified, I click and wait... .i have tried cleck say the oposie and wait. It seems as it asks me to authorize the installation program must be installed. I don't want and I can't get rid of it.

  Hello

  There is a possibility that it is Adware.

  Read this information about it:

  http://www.ehow.com/facts_7898673_install-IQ-Updater.html

  Try this.

  Use the FREE Revo Uninstaller to remove it:

  http://www.revouninstaller.com/revo_uninstaller_free_download.html

  And I would also do a scan of Malware;

  Download, install, update and scan your system with the free version of Malwarebytes AntiMalware, if necessary in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  See you soon.

• Unable to access the control panel in Windows 7

  When I try to open the Control Panel, the icon appears in the taskbar, then I see the control panel real screen disappear off the coast to the right of the screen. "When I click the icon on the taskbar again, I can see the screen"Shuttlecocks"back" but it will not be open on the screen, so I can use it no matter what I try. What is the cause? I was able to use the control panel the day I booted up my new PC, but have not been able to use it since then. Then the only thing I've changed after the start-up of the first time he was my desktop theme... Help, please! Thank you.

  Nevermind, I resolved. Found the settings indicating that I had two monitors put in place. Once I put it to a monitor, the problem has been resolved. Have a great day! Just connect "newbie to Win7" :-)

• insterted my IBM &amp; reg travelstar 2.0, it is recognized as being plugged but doesn't show on the control panel and I can't access it.

  insterted my IBM & reg travelstar 2.0, it is recognized as being plugged but doesn't show on the control panel and I can't access it.

  I don't know what to do because he has all my work on it. An error report has been sent to me by saying: "Windows has detected a new device attached to your computer, but could not find the driver software, make the device usable. Each device manufacturer typically includes the driver from a CD that comes with the device, or for download on its Web site. Your device hardware ID is ACPI\HPQ0006. »

  What should I do?

  Hi Rachael7861,

  1. have you installed the latest drivers for the hard disk, mentioned in the previous post?

  I suggest that you connect the hard drive to another computer to check if it is broken.

  Also check in Device Manager for the status of the hard drive.

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.