Network installation error 0x0000000d printer?

Similar Questions

• Installation of the printer. error: "printer spooler does not.

  Original title: printer Installation

  Windows XP SP3 home edition:

  Software printer installation error message, "printer spooler does not" no printer is installed or deposited.

  This suggestion can help.

  Quote from: http://snipurl.com/1mdayq [www_eventid_net]

  From a newsgroup post: "it seems that the print spooler does not and that it was impossible (or not configured to) restart itself.» When the print spooler does not work, printers will be not visible in the Printers folder, and you will not be able to add a new printer. A number of things could cause the print spooler to fail. It's corrupt print jobs, incompatible or problematic printer drivers or port monitors, corrupted file or disc and even other applications or processes interfering with the spooler in memory. If you try to manually restart the print spooler and it fails immediately, he may be trying to process a print job corrupted after the start. It is a common cause for the print spooler failures that occur immediately. If the print spooler starts and printing features returns for a while before a failure once again, then a monitor driver or the port is probably the cause of the problem.

  To remove print spooling jobs that could cause this problem, simply remove (or remove) the files with the extension ".spl" or ".shd' of the location of the coil when the print spooler is stopped. This place is typically "c:\\system32\spool\printers" (it might have been edited manually). Once the existing spool files have been deleted, try to restart the print spooler again to see if it works normally. If there is no (.shd or .spl files) spooling print jobs, or remove the old spooling print jobs does not change the behavior, a port monitor or driver may be to blame. " M260142 provides information more detailed which will be useful in troubleshooting.

  Hope this helps, Gerry Cornell

• Get the add printer error 0x0000000d network

  Hi all, Vista SP2 Ultimate x 86
   
  I'm in dual boot on my HP Pavilion laptop with Vista Ultimate SP2 x 86 and
  XP Pro SP3 x 86. I have a home network with a wireless router and run it
  wireless laptop.  I have 2 desktop computers that are also wireless on the network
  and connect to the printer via a switch. I have an another desktop which is
  hard wired to the modem with a printer connected directly and is also in
  the network. All desktop computers can access the printer in question through the
  the network and cannot therefore have the XP Pro on the laptop of the subject.  They are all set
  place correctly, the network can share files and these very well.  However,.
  When I try to add/connect the printer to the Vista on the laptop to the
  Network on a desktop printer, I get the operation could not be completed:
  error 0x0000000d.  I've been on the Internet looking for a 3 days
  solution, but so far, none of the recommendations, the command prompts for
  registry changes worked.  The drivers for this printer are installed on
  the laptop in the Vista operating system and up to date.
   
  When I try to add the printer from Office Word 2007 I get the error: 'the
  Active directory domain services is currently unavailable. »
   
  What is strange is that I can access the printer of every machine on the
  network, but the computer of one office. I can access all the drives and files on
  This same office via the network, but not the printer. I know that the
  printer works when I switch on the desk to the other of all the
  other machines, is not the switch that is at fault.  Also, I have
  the same Vista Ultimate, SP2 x 86 installed on two other desktops, which doubles
  Boot with Win7 SP1, and they have no problem accessing the printer via the
  network.
   
  Any suggestion would be appreciated. I'm really confused as to what
  could cause the error or the place where the problems at this stage, as it is
  only this a Vista on a laptop that is causing the problem.
   
  Jan :)
   
   

  After days of troubleshooting and follows all the information from the Internet and same MS supports with no luck, at my wits end, I finally uninstalled the printer in Device Manager driver, once again and then reinstalled it, but this time chose the second of the two ports USB for that and said he did not replace the existing driver. There was the new driver of the same name, but with the (copy 1) on this subject. I went to another desktop computer and tried to add the printer again, and for any reason or madness, connected to the printer (1 copy), as did the Win7 on this desktop and Vista on the laptop. Now, all computers are connected once more.

  Jan :)

  "Jan Ilacqua," <*** email="" address="" is="" removed="" for="" privacy="" ***="">wrote in messageNews: * e-mail address is removed from the privacy *...

  Hi all, Vista SP2 Ultimate x 86

   

  I'm in dual boot on my HP Pavilion laptop with Vista Ultimate SP2 x 86 and

  XP Pro SP3 x 86. I have a home network with a wireless router and run it

  wireless laptop.  I have 2 desktop computers that are also wireless on the network

  and connect to the printer via a switch. I have an another desktop which is

  hard wired to the modem with a printer connected directly and is also in

  the network. All desktop computers can access the printer in question through the

  the network and cannot therefore have the XP Pro on the laptop of the subject.  They are all set

  place correctly, the network can share files and these very well.  However,.

  When I try to add/connect the printer to the Vista on the laptop to the

  Network on a desktop printer, I get the operation could not be completed:

  error 0x0000000d.  I've been on the Internet looking for a 3 days

  solution, but so far, none of the recommendations, the command prompts for

  registry changes worked.  The drivers for this printer are installed on

  the laptop in the Vista operating system and up to date.

   

  When I try to add the printer from Office Word 2007 I get the error: 'the

  Active directory domain services is currently unavailable. »

   

  What is strange is that I can access the printer of every machine on the

  network, but the computer of one office. I can access all the drives and files on

  This same office via the network, but not the printer. I know that the

  printer works when I switch on the desk to the other of all the

  other machines, is not the switch that is at fault.  Also, I have

  the same Vista Ultimate, SP2 x 86 installed on two other desktops, which doubles

  Boot with Win7 SP1, and they have no problem accessing the printer via the

  network.

   

  Any suggestion would be appreciated. I'm really confused as to what

  could cause the error or the place where the problems at this stage, as it is

  only this a Vista on a laptop that is causing the problem.

   

  Jan :)

   

   

• Error 0X0000000D when you add the network printer at home

  Original title: try to add a printer to My Desktop 2 which is connected via a USB port on my desktop computer 1. Both are pre-cabled linked to my home network. They are both under Vista.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  1. Programs that you have problems with adding printer
  • Error 0X0000000D
  • Recent changes made to your computer no
  • What you have already tried to solve the problem, not yet

  Usually, you insert the printer cd in desktop1 and follow the procedure for setting up a shared printer / network

• An error 0 x 00000643 attachment with the installation of the printer

  I am running Windows Vista on a laptop and I am trying to install a wireless printer.  I get error 0 x 00000643.  I went to the windows support center and performed all workaround solutions that he suggested.  The WSD port has been deleted, but whenever I try to install the printer fails and returns the WSD port.  When the WSD port is removed, the installation fails without code.  I've had this installed printer so it worked before.  Any ideas?

  Hi Moyerhouse,

  Thank you for visiting Microsoft Answers.

  (a) don't you make changes on the computer before this problem?
  (b) who is the manufacturer of the printer?
   
  I first suggest you to run the tool to 'Fix' of Microsoft that automatically diagnoses and repairs printing problems, installation of a printer, connecting to a network printer and other related errors.

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Let ' also install the latest drivers for the printer from the manufacturer's website and check if it helps.

  OR

  You can also uninstall the printer using the network browser and install it again. To do this, follow these steps:
  Open the network and sharing Center. To do this, type Network Center and sharing in the search box and then click Network Center and sharing in the list programs.
  In the pane tasks, click view computers and devices.
  Locate the printer, and then right click on the printer to uninstall.
  Once the printer is uninstalled, connect the printer to the computer again. The Plug-and-Play service begins to install the printer.

  Reference:
  Error message when you try to install a WSD printer on a Windows Vista-based computer after installing first attempt fails: "impossible Operation completed (error 0 x 00000643).
  http://support.Microsoft.com/kb/944960
   
  Hope the helps of information. Please post back and we do know.
  Concerning
  Joel S
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why can not print with a shared printer, the error 0x0000000d?

  I used to be able to print from a shared printer, but now when try to connect, I get the error 0x0000000d. I have Windows Vista Home Basic Edition. I even went to donloaded and the Canon Web site drivers for the Web site.

  Hi Ag52,

  Thanks for posting on the forums.

  Please take a look at this article on

  Error message when you try to install a network printer on a Windows Vista-based computer: "Windows cannot connect to the printer operation cannot complete (error 0x0000000d).

  http://support.Microsoft.com/kb/947236

  Hope that helps, please post back and we do know.

  JohnD
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7 cannot connect to a shared printer (error 0x0000000d code)

  I try to add a laptop to my home network and can not get the printer to connect.  Everything is wireless.

  The main PC uses Windows 7 Home Premium.  32-bit operating system.

  The new laptop uses Windows 7 Professional.  64-bit operating system.

  The all-in-one is Kodak ESP9 + 0250.

  The laptop recognises the printer on the network, but I get the error message: Windows 7 cannot connect to a shared printer (error 0x0000000d code)

  Any ideas on how to make the printer connect?

  The usual reason is no driver on the laptop. You should install the drivers and the software of the printer on each computer on the network. Once this is done, it will connect well. The network itself, will show the printer as a gift, just the laptop won't connect ' cuz he doesn't know how.

  Many answers here: http://social.technet.microsoft.com/Forums/windows/en-US/d02718d8-cf5d-45de-9206-46714a549ee0/windows-cannot-connect-to-the-printererror-0x0000000d?forum=itprovistaprinting

  .

• We get an error "NETWORK CONNECTION ERROR, make sure a firewall is not blocking access to the printer.

  * Original title: printer error...

  I was printing with a printer wireless for months and now all of a sudden I'm getting an error, NETWORK CONNECTION ERROR and then readings make sure that a firewall is not blocking access to the printer.   I checked and it is not blocked...  I did a session of disorder and it reads no problems found.   Can someone please...

  Hello

  1. what version of Windows is installed on the computer?

  2. What is the brand and model of the printer?

  3. you have any non-Microsoft firewall installed on the computer?

  4. what security software is installed on the computer?

  5 have have there been recent changes made on the computer before the show?

  Please follow the steps below and check if that helps.

  Method 1: Run troubleshooting network printer and check.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Method 2: Select the file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows-Vista/enable-file-and-printer-sharing

  Method 3: I suggest to change firewall security settings, or disable the security software on the system and try to access the printer.

  Note: make sure that you enable the antivirus software, other security and firewall after the test programs.

  For more information, see the articles and check out them.

  Understanding Windows Firewall settings

  http://Windows.Microsoft.com/en-us/Windows-Vista/Understanding-Windows-Firewall-settings

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Allow a program to communicate through Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/allow-a-program-to-communicate-through-Windows-Firewall

  Let us know if it helps!

• 8500 A909a-network installation will not continue because of error USB

  Try to install a network printer on a Workstation Windows XP 32 - bit virtual (MS Hyper-V).  Even if I choose network installation, the software stops after checking the system requirements because there is no available USB port.  There is no other choice to avoidance (because I do NOT want to install anything USB).  The only choice is to cancel the installation.

  Message edited by tsg on 07/09/2009 18:03

  Problem solved.

  Solution is the same as in the thread linked to above, except that the file to modify is autorun_network.inf instead of autorun.inf.

  1. Open autorun_network.inf in Notepad.  This file is located in the folder root of the installation CD or the folder where you extracted the driver you downloaded from HP (if using the CD, copy the entire CD to a temporary folder on your hard drive to allow the edition)
  2. Search for "[SystemRequirements]."
  3. Add the line 'MinUsbReady = 3' anywhere in the section [SystemRequirements]
  4. Close Notepad and save the file
  5. Run setup.exe, select install network and it will ignore the USB control

  Thanks to Mr. Richard Wang for the solution.

• HP8610e: get message network installation HP8610 lan connection failure

  Using set up disk, I get the network fails Installation message: the printer could not be installed on the network. I use the connection to the local network

  Hey @graemea,

  Welcome to the Forums of HP Support!

  I understand that you encounter a "network without successful installation" error during the installation of your HP Officejet Pro 8610 e-all-in-one printer for an ethernet connection on your computer Windows 8.1. I would like to help you today to solve the installation problem. Can I please you follow the steps below.

  Step 1: Remove the drivers:

  Even if the installation fails, there is a chance that a part of the software package and the pilot has made its way on your computer. For the purposes of troubleshooting, it is crucial that we have a clean slate to work with. So, I'll let you remove all traces of your HP Officejet from your computer.

  1. Open your screen to Start by selecting the Windows icon at the bottom left of your computer screen or by selecting the Windows key bottom left of your keyboard, to the right of the Ctrl key
  2. In the start screen, type programs and features. Click on programs and features to start.
  3. In the window programs and features will populate a list of the programs installed on your computer. Please scroll through this list and find your HP Officejet
  4. Click on the HP Officejet device and select Uninstall
  5. Please follow the prompts on the screen to complete the uninstall
  6. Once the uninstall is complete, please close the window programs and features. Please proceed to the next step below.

  Step 2: Remove temporary files:

  1. Open your screen to Start by selecting the Windows icon at the bottom left of your computer screen or by selecting the Windows key bottom left of your keyboard, to the right of the Ctrl key
  2. In the start screen, type run. Click on Run to launch the run dialogue box
  3. In the run box, type %temp% , and then click OK
  4. When the Temp folder opens, select Ctrl + A at the same time on your keyboard. Everything in this folder will highlight now.
  5. Select the "delete" button on your keyboard. The Temp folder contains the temporary internet files. None of the actual files or folders on your computer will be affected by deleting Temp files. A Temp file should you will automatically get the pop up to 'jump' this point.
  6. Close the Temp folder when it is empty
  7. Right-click the recycling bin on your desktop and select empty recycling bin

  Step 3: MSCONFIG (disable):

  A program running on your computer can cause interference when you try to install your network printer. I'm going to make sure that no program will cause problems, you temporarily turn off background programs on your computer.

  1. Open your screen to Start by selecting the Windows icon at the bottom left of your computer screen or by selecting the Windows key bottom left of your keyboard, to the right of the Ctrl key
  2. In the start screen, type run. Click on Run to launch the run dialogue box
  3. In the run box, type msconfig and click OK
  4. When the System Configuration window opens, select "selective startup" and uncheck load startup items
  5. Click the Services tab, check the box at the bottom to hide all Microsoft Services
  6. Select turn off all the
  7. Select apply and OK
  8. Computer restart when you are prompted. When your computer turns on, proceed to the next step.

  Step 4: Install the device:

  1. Please click here to download the latest drivers for your HP Officejet
  2. Once the download is complete, follow the instructions on the screen to install your printer on a network
  3. Once the installation is completed successfully, please test the functions of your machine to confirm that everything is working properly. Once you have confirmed that the printing and scanning are use, please proceed to the last step to Activate substantive programmes and test the machine one last time.

  Step 5: (MSCONFIG (Enable):)

  1. Open your screen to Start by selecting the Windows icon at the bottom left of your computer screen or by selecting the Windows key bottom left of your keyboard, to the right of the Ctrl key
  2. In the start screen, type run. Click on Run to launch the run dialogue box
  3. In the run box, type msconfig and click OK
  4. When the System Configuration window opens, select Normal startup
  5. Select apply and OK
  6. Computer restart when you are prompted. When your computer turns on, please test the functions of your machine to confirm that everything works again according to normal.

  Please reply to this message with the result of your troubleshooting. You can also click thethumbs up' ' icon below to say "thanks for the help!" I look forward to hear from you!

• LasrerJet P2015n: Low error when printing with ePrint to a LaserJet P2015n on iOS supplies

  "Hi, I'm using the HP LaserJet P2015n, which works very well, however try to print using ePrint on iOS 8.3 seems to cause problems. If the application finds the printer on the network, and try to print, it invites a mistake "we have detected you are low on supplies error" obviously is not the case, because it is more than 50% of the full and prints very well using the desktop computer. The printer error LED keeps blinking and won't not even respond to a request for printing office. It must be restarted to work again.

  Tried all kinds of reboot and reset. I also tried to find a solution with no luck, there is no updated firmware for this printer can be found as well.

  Any help will be very appreciated!

  @hussain316

  Thank you, based on the information you provided... the p2015 is not taken care of with ePrint. That's why whenever you send a print job for printing, the printer responds with error messages and you have to pick up then power cycle the computers can be printed successfully on it.

  If you want to start mobile printing, then you will need to upgrade to a new printer with function ePrint. Depending on your price range, the new m277 is a nice little printer and has this ability.

  Sorry

• Satellite A660: HW Configuration. Network Error1316 error has occurred

  I have an annoying problem on my Satellite A660 that I can't fix. I lost the use of my function and the function of flash card keys. It seems to be linked to the HW configuration utility which open habit.

  When I click on the icon that this message reaches this application requested execution to terminate in an unusual way. I tried to reinstall Hwsetup but it will not do so either by relocation or uninstall and this message, T / hw installation. Network Error1316 error occurred trying to read from c. \Windows\installer\Toshiba Hardware Setup.msi

  Error 1603 Fatal error. Consult windows help install (msi.chm) or MSDN for more information.

  I downloaded a new copy of Hwsetup but still no change. I also tried restoring from restore points much earlier, but even once, nothing changes. Would be very grateful any advice, Bravo Jeff

  Hello

  Maybe this error message is related to the issue of the register
  I found a same error message in MS. knowledge base article The error appears while you are upgrading an existing installation of Office 2000.
  http://support.Microsoft.com/kb/263253

  I think you should clean the registry with CCleaner.
  Firstly uninstall the Toshiba HW setup utility.
  Then uninstall the VAP (value added package)
  Reboot the laptop.
  Now run the CCleaner and clean the registry and delete the temporal files.
  Reboot the laptop.
  Run the CCleaner once more to make sure that the registry is properly cleaned.
  Reboot once more and then install VAP.
  Reboot once again and install the program HW installation.

  Good luck

• Satellite Pro L300 - missing dll. files after the installation of the printer

  Hello

  I have missing dll. files on my Pro L300.
  When I try to install my printer software it throws an error message upward.
  I now have the missing dll. files, but can't seem to install them. Someone knows what to do with them?

  I am running XP and the files are sccbase.dll slbcsp.dll

  I have listed this question before, but it has never been on the forum?

  Thank you very much

  Q

  Hello

  I searched and slbcsp.dll sccbase.dll and found someone who had the same problem after installation of the printer software.
  Check out this site:
  http://forums.CNET.com/5208-6142_102-0.html?ThreadId=275051

  Please post some feedback after you try the workaround solution posted here.
  It looks like a registry key must be changed.

  Good luck

• Connection Manager HP stopped responding + Windows Installer Error 1719

  I am running Windows 7 (SP1) 64-bit operating systems.
  
  Started getting an error message of connection manager HP "HP Connection Manager Service has stopped responding.  Error code 8008005.
  
  HP Connection Manager v4.1.23.1 running.
  When I try to install a new version of v4.4.10.1 (SP58930) HP connection manager, I get an error of Windows Installer 1719.  Tried different solutions recommended for this, but nothing has worked.
  
  I see in the forum after this uninstall of the current version and then install the new version of the HP connection manager can solve my original problem.
  
  Before uninstalling the currenet HP Connection Manager version, I wanted to be sure that I will be able to install the new version without encountering Error 1719.  I don't want to be in an even worse situation of not being able to the HP Connection Manager after you uninstall it.
  
  Can I get confirmation from HP that I will be able to successfully install a new version after uninstalling the current version?

  ParryJM wrote:
  

  A ran the Microsoft Fixit then tried to install it and got the Windows Installer Error 1719.

  Then uninstalled HP connection Manager.

  Tried to install the HP (SP58930) connection manager and still have the error Windows Installer 1719.

  What do you suggest I try next?

  The fact that HP Connection Manager is no longer installed, how this will affect my computer?

  The fact that it is no longer installed will have no effect on the functioning of your laptop and none on the operating system.

  HP connection manager is simply a utility assistance for people who are making it difficult for the network through conections wifi and bluetooth connections.

  If you are not in this group it is really useless.

  From your description, it seems that if you can't follow instructions in the Microsoft fixit to the letter. By using the fixit is the easiest way to remove the registry entries and make changes to the registry that will allow installing and uninstalling software.  I can't recommend the methods that I use personally when I run on these issues because they involve access to the registry via regedit. The word people have never even heard of Regedit. Using Regedit can be a very bad thing for someone not experienced in the use of the registry editor.  All ch = angels did take place immediately and which included all the mistakes made during the access to the registry. Ongoing work on an operating system can fairly easily through the registry editor. Try the Microsoft fixit. It is a safe utility. Use it after an attempt to install and leave the window open until after error that does compete with the installation of the software.

• OfficeJet 6600 Gets the message of Network Installation fails when you try to install

  Hello

  I have the worst time setting up my new printer wireless Officejet 6600. I work with a wireless-N router that was purchased less than a year ago. I have other wireless products that work well with the internet, so I do not see there is a connectivity problem.

  The test of the printer indicates that everything is OK:

  Wireless on - PASS
  Wireless - PASS work
  Signal quality - very good
  Connected - PASS

  etc, etc.

  I ran through all the troubleshooting I can find and nothing works. I have disabled the firewall, unplugged my router and modem, disconnected the printer, tried to implement on its own IP address. The installation wizard finds her and tries to implement, but I only get the message that it was a "network installation without success.

  Has anyone experience this problem?

  Any new ideas on troubleshooting are welcome.

  Thank you
  Liz

  Hello

  Thank you for your comments. I didn't expect such a quick response, which was great.

  I move the printer to get a signal 'excellent' and tried the other steps you listed.  Through some googling more, we discovered that we needed to do the following:

  Go to the control panel

  Select Printers and faxes

  Right click and select Properties

  Select the Ports section

  Add the port to the IP address of the printer displays

  Not sure if this is the ideal way, but of course, it worked and I am now a happy customer. Hope it helps someone. I'll still Bravo for having responded so quickly.

  Thanks again!