New RAM in p6310f causes BSOD. Aries is Corsair CMX8GBX3M2A1333c9.

Similar Questions

• Tecra S3 - cannot use the new RAM modules in the B slot

  Hi all

  I just bought two RAM modules of 1 GB to replace my old 512 MB one. This, as far as I know, is the maximum allowed by my Toshiba Tecra S3 (PTS30E-01000QSP).

  When I put a module in A slot, the machine works perfectly; If I place a second in location B, the computer tries to start but, at a time given, it freezes just (no activity of the HARD drive or changes on the screen) and the fun begins racing on as if some process crashes in the CPU to heat that make it up. At this point, I was always afraid that the heat can damage the computer and be turned off by pressing the on/off switch, so I can't tell if the problem is solved simply waiting.

  I swapped the two modules on A slot and the two work well when they are the only one on the machine. Pretty funny if I place (as is the case now) has the old 512 MB in the location B as well as a single module of 1 GB in slot, it works!

  My BIOS has been upgraded to the last, that I could find in these same pages (version 3.20 if I'm not mistaken), but it made no difference. If I enter the page of the BIOS when the two 1 GB modules are present, the BIOS recognizes that they are there. This behavior occurs when I try to start Windows or Linux.
  Honestly, I'm puzzled. Someone has an idea what can happen and how I could place the two modules on my machine?

  Thank you very much and sorry for the long post

  O.

  Hello

  The modules you purchased exactly for your Tecra S3? Maybe that they are not compatible with the laptop and it hangs after a few minutes.

  Normally, the Tecra S3 can handle up to 2 GB and that means 1 GB in each slot. For modules of Toshiba part number is PA3411U-1M1G.

  In my opinion you should try it with other modules with original 512 MB module everything works so I guess your new RAM is the cause of this problem.

• error 0x0000007B (0xf78a2524, 0xC0000034, 0x00000000, 0x00000000) after the installation of the new RAM

  I get the BSOD when booting with the STOP: 0x0000007B (0xf78a2524, 0xC0000034, 0x00000000, 0x00000000) message. The computer is a Dell Dimension 8400. I installed the new ram to find this message and we tried him swinging back the RAM on the former with the problem still persists.

  Hello

  Very good chance you loosened a cable or connection when you replaced the
  memory.

  Check with Dell Support, their drivers and documentation online and ask in the Dell
  forums for known issues.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  ================================================================

  Check the disk for malware:

  Create a Bootable CD with the Trinity Rescue Kit - free - which comes with 5 antivirus programs
  Integrable Hirem is another choice - more can be found using Google.

  Trinity Rescue Kit - download on top right of the page
  http://trinityhome.org/home/index.php?wpid=1&front_id=12

  CD of Hirem boot is another good choice
  http://www.hirensbootcd.NET/Download.html
  http://www.hirensbootcd.NET/CD-contents/138-HBCD-111.html

  ===================================================================

  You can also save the data and re-install Windows 7. The hard drive can be set
  another computer as a 2nd drive (the best) or in an external USB enclosure. Either would allow
  allows you to copy the data to removable media such as CD, DVD or other USB drives.

  Or you can use a boot Ubuntu CD to back up data.

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  ===================================================================

  For slightly more:

  BCCode: 7B 0x0000007B<-- read="" this="">

  INACCESSIBLE_BOOT_DEVICE bug control has a value of 0x0000007B. This bug check indicates that the Microsoft Windows operating system has lost access to the system partition during startup.

  Important information if you have received a STOP Code

  If you have received a blue screen error, or stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer connect with Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  The following actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  Cause

  Bug INACCESSIBLE_BOOT_DEVICE control often occurs due to a failure of the boot device. During the initialization of the I/O system, the boot device driver could have no initialize the boot device (usually a hard drive). Initialization of file system may have failed because it does not recognize the data on the boot device. In addition, repartition the system partition or installing a new SCSI adapter or disk controller could encourage this error.

  This error can also occur because of incompatible disc material. If the error occurred in the initial configuration of the system, the system have maybe installed on an unsupported drive or a SCSI controller. Some controllers are supported only by the drivers that are in the library of drivers Windows (WDL). (These drivers require the user to perform a custom installation.)

  
  Resolution

  This error always occurs during the startup of the system. This error often occurs before the debugger connection, kind of debugging can be difficult, if not impossible.

  Fix a defective boot device: If a boot device is at fault, you must change the boot options. For more information changing these options, see Software Configuration on the target computer.

  Solve a problem of incompatible hard disk: If the installation program automatically detects the controller, you may have to skip the detection and the disc of the specific manufacturer allows to load the driver. Also, check the availability of updates for the firmware of the system BIOS and SCSI controller. Updates of this kind are usually available on the website or BBS of the hardware manufacturer.

  Delete all material recently added, especially of hard disks or controllers, to see if the error is resolved. If the problematic material is a hard drive, the firmware version of the drive may be incompatible with your version of the Windows operating system. Contact the manufacturer for updates. If you have removed another material element and the error is resolved, conflicts of port IRQ or i/o likely exist. Reconfigure the new device according to the manufacturer's instructions.

  Confirm that the hard disk drivers, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.

  If you have recently added a driver, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the menu of Advanced Options , select the last known good Configuration option. This option is most effective when you add a single driver or service at a time.

  In addition, check your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.

  This error can also occur due to corruption of the hard drive. Run Chkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and run Chkdsk/r.

  If you cannot start the system in the last known good configuration, you should try to boot from the Windows CD. Then, you can run Chkdsk from the Repair Console.

  Warning   If your system partition is formatted with the FAT file system the long file names that use the Windows operating system could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.

  If your system has SCSI adapters, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination. For IDE devices, define the IDE port integrated as primary only. Also check each IDE device for setting good master/subordinate/stand alone . Try to remove all IDE devices except for the hard drives. Finally, check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error.

  BCCode: 7B 0x0000007B<-- read="" this="">
  * 1138.html? order = votes http://www.faultwire.com/solutions-fatal_error/Check-for-viruses-on-your-Computer-0x0000007B-

  =================================================================

  If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
  protected. The manufacturer of your system will also sell the physical DVD cheap since you already
  Clean Windows. You can also do an ERD on another computer.

  Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
  return and then try to startup repair.)

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Try the disk Options recovery or Windows 7 startup repair.

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  Also from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  Retry After Chkdsk startup repair.

  If after those you can try the system restore to fashion without failure or the valuation or Windows 7
  disc.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  --------------------------------------------------------------------

  If you need to repair disks - these help repair Windows not re-install.
  Often an ERD will help you when the recovery disk is not - use OPTION 2 to
  make the disc.
  
  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  ======================================

  If necessary:

  What to do if Windows does not start correctly
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials

  I hope this helps.

• Geniune Intel causing BSOD

  MS community,

  I added some hardware from Razer (Blackwidow Ultimate keyboard & DeathAdder mouse) my system, a month or two before, and Synapse 2.0 caused BSOD regularly, so I took out starter, and my system has worked very well, until the last two weeks. I am not usually the addition or removal of hardware or software, so maybe I'm picking up cyber-Carbuncles in surfing on... not sure. In any case the last two .dmp files are on OneDrive: http://1drv.ms/1tpXPpW. I hope one of you very smart people can help me understand what is causing my plant.

  Thank you all in advance!

  Baird

  Original title: BSOD are back...

  WBM

  These 2 are called BCC124 and are related to the material.  Since the real interest is mentioned I would run the cpu stress test first

  I would also remove the app associated with Bus Marvin/MarvinPro MarvinBus.sys from Pinnacle Systems enumerator.  (yours is 2005)

  Try this free stress test: http://www.mersenne.org/freesoft/

  
  Prime95 Setup program;
  -Extract the contents of the zip file into a directory of your choice
  -Double-click on the executable file
  -Select "all stress testing.
  -Select the test of 'Blend '.  If you have already run MemTest overnight, you can run the test of "Small FFFS" instead.
  "Number of threads of torture test run" must equal the number of processors multiplied by 2 (if you use hyperthreading).
  The best way to do this is to go to the Manager of the tasks of the figure... The performance tab - and see the number of boxes that appear under the CPU usage history
  Then run the test of 6 to 24 hours - or until you get errors [b](whichever comes first)
  The selection of Test and the file stress.txt box describes the components that insists on the program.
  Stop 0 x 124 is a hardware error

  If you are overclocking try to reset your settings to standard processor and see if that helps.

  If you keep getting the BSOD here are things more than you may want.
  This is usually hardware related, defective heat, memory or processor even if it is "possible" he is associated (rare) driver.
  
  Stop 0 x 124 - what it means and what to try
  Synopsis:
  A "stop 0 x 124" is fundamentally different from many other types of bluescreens because it arises from a complaint of material.
  Stop 0 x 124 minidumps contain very little concrete information, and it is therefore necessary to address the problem as a case of material in an unknown state of distress.
  

  Generic troubleshooting ' Stop 0 x 124 ":

  1) to ensure that none of the hardware components are overclocked. Material which is pushed beyond its design specifications - by overclocking - may malfunction in unpredictable ways.
  (2) ensure that the machine is sufficiently cooled.
  If there is doubt, open the side of the case (be aware of all the relevant conditions guaranteed!) PC and direct an electric fan squarely to the motherboard. Who will rule on most cooling problems (lack of).
  3) update all drivers related to materials: video, sound, RAID (if applicable), NIC... anything that interacts with a piece of hardware.
  It is best to run the latest drivers anyway.
  (4) update the BIOS of your motherboard according to the manufacturer's instructions and clear CMOS.
  Their website should provide detailed instructions on the brand and model-specific procedure.
  (5) rarely, bugs in the operating system may cause "false positives" 0 x 124 events where the hardware wasn't complaining, but Windows thought otherwise (because of the bug).
  At the time of writing, Windows 7 does not have to suffer from a defect, but it is nevertheless important to keep Windows up-to-date.

  
  6) trying (stress) test these hardware components that can be put to the test artificially.
  The most obvious examples are the RAM and HDD (s).
  For the RAM, use the 3 rd-party memtest86 utility to run several hours a test value. (6-8 passes to stress the ram)
  For hard drives, verify if CHKDSK /R finds any problems on (s), including "bad sectors".
  Unreliable RAM, in particular, is mortal, as well as software, and anything other than a 100% clear memory test result is cause for concern. Unfortunately, even a 100% clear result the diagnostic utilities does not guarantee that the RAM is free of any defect - only that none have been encountered during the test passes.
  7) as the last of the non-invasive troubleshooting steps, perform a "Vanilla" Windows reinstallation: just the OS itself without additional applications, games, utilities, updates, new drivers - or ANYTHING that does not come from the Windows 7 disc.
  Who stops working mitigate the problem of the 0 x 124, jump to the next step.
  If you run the "Vanilla" installation long enough to convince yourself that not a single 0 x 124 accident occurred, start installing applications and updates slowly, always stopping between successive additions long enough to get an idea of the question if the machine is still free of 0 x 124 breaks down.
  Smash back, obviously the latest addition of software may be somehow connected to the root cause.
  If the stop error 0 x 124 persist despite the above steps, and the equipment is under warranty, consider to go back and ask for a replacement that does not suffer periodic MCE events.
  Be aware that want to perform the subsequent hardware troubleshooting steps can, in some cases, void your warranty:
  (8) clean and carefully remove the dust inside the machine.
  Reinstall all memory modules and connectors.
  Use a can of compressed air to clean the RAM DIMM supports as much as possible.
  (9) If all else fails, start removing items of hardware one by one in the hope that the culprit is something non-essential that can be eliminated.
  Obviously, this type of testing is much easier if you have access to equivalent components in order to perform swaps.

  If you are in the situation to have completed all the steps above without a resolution of the symptom, unfortunately the most likely reason is that the error message is literally correct - something is fundamentally wrong with the hardware of the machine.

  
  
  More advanced reading can be found here from a MS MVP IT PRO
  http://captaindbg.com/bug-check-0x124-whea_uncorrectable_error-how-to-troubleshoot/

  

• Satellite Pro 6000 - new RAM does not work

  Hi all

  New to this forum sorry if this was asked before, I did a search but could not find anything so here goes.

  I just bought a new RAM for my Satellite Pro 6000. When I install it nothing happens the laptop won't boot. If I put the old stick in no problem. The ram I bought is unb 512 MB PC133 CL3 and old RAM 256 MB PC133s. I think little small to read with these old eyes.

  I was told I might need an update of the BIOS but cannot find one for my laptop under 1.4 for the moment.
  Any help would be thank Lindsey

  I think that the new RAM is not compatible with the motherboard or laptop.

  The manufacturing of the new RAM you said does not for me so I would buy an another RAM, such as Kingston. Kingston makes high quality RAM and many users here buy Kingston RAM to upgrade its RAM.

  By the way: do you use the RAM or only the new? Normally, if you use two memory modules live, you must use it with the same specifications.

  The update of the BIOS, you can find the Toshiba site, but this doesn t affect the compatibility of Aries.

• New RAM should work, but doesn't work!

  Hey

  I have / had a SR5019uk, I have somewhat changed i.e new cases, big New/more drive, more RAM, better graphics (Nvidia GeForce 8400GS), better CPU(Athlon 64 X2 5000+).

  Now, I put the hand on some new ram that will improve that PC without end but it doesn't seem to work when I put it in with 2 sticks of the current RAM

  RAM in = 4 x 512 MB PC2 4200 DDR2 533 Mhz 4-4-4-12

  Go to:

  New RAM = 2 x 1 Gb PC2 5300 DDR2 667 Mhz 4-4-4-12

  I put it as follows: 1 Gb / 512Mb / 1 Gb / 512Mb<---- 4="" slots="" as="" you="" can="">
  Allows dual channel

  Everything I read says that it will work together; everything in the range of 533 Mhz, but I can live with that for the extra 1 GB of RAM
  Read also the Mobo card and he said he can support the two types I listed

  Mobo = Asus M2N68 - LA
  HP/Compaq name = father-GL8E

  But... Nothing.

  Beep beep Beeeeeeeeeeeeep! ...             <----  is="" all="" i="" get=""> To the Mobo

  Help!

  Looks like a serious machine.  This information can be useful in determining the cause or the source on the beep codes and what they're trying to diagnose.  Let me know what happens.  This, by the way, is my own opinion and not that of HP.

  http://support.HP.com/us-en/document/bph07107

• Somehow my new Apple TV 4 causes my Panasonic Plasma TV turns off every 30 to 60 minutes.

  Somehow my new Apple TV 4 causes my Panasonic Plasma TV turns off every 30 to 60 minutes. I thought for sure I had capacitor problems with my TV (he is about five years old) but my wife suggested to check our new ATV4 because the problem started just after Christmas when we got the new ATV4 and the problem occurs with our ATV3. I was skeptical but I have tried to unplug the power cord on the ATV4 and to my surprise the TV cutting question disappeared, so I have to have my ATV4 unplugged when not in use and plug it in when I want to use it, a real pain in the *. If accidentally, I forgot to unplug my ATV4 after using my TV stops every 30 to 60 minutes after my ATV4 is connected and not in use. I'm at a complete loss as to what is causing this problem. For any help or suggestion would be appreciated.

  ATV turns off after a certain period of time in the settings: http://help.apple.com/appletv/#/atvb7a7550e3

  The ATV also has the ability to control the power of the TV via the HDMI cable, if the value.

  I will try to put the ATV to sleep immediately after use, as explained above and see if the TV turns off then.

  If so, go into the settings, remote controls and disable control of your home with remote control entertainment system and see if only he stops.

  When the TV turns off, it is on the entry of Apple TV and the screen saver or you look at another entrance, for example, a cable?

• New RAM not working not not on iMac 2010

  Hello

  I have a 21.5 ' mid year 2010 i3 iMac, and, after all this time, it was time to upgrade the RAM.

  I bought 2 x 4 GB Patriot SODIMM PC3 - 10600 1333 MHz 204-pin, by following the instructions in the Web page of Apple memory upgrade (install memory in an iMac - Apple Support).: 4 GB RAM SO-DIMM memory DDR3 SDRAM 1333 MHz. I installed it according to job with factory 2x2gb RAM Samsung sticks. After a reboot, everything worked beautifully for about 6 minutes. The identified computer sticks again and showed me a full 12 GB available. Which was great, since Yosemite + a few browser windows and Spotify only lasts up to 3GB. I have enough to spare. However, it restarted and again and again and again.

  I decided to test only the new RAM and started with the combination of Patriot 8 GB. It froze on reboot and fully started once, but it restarted less than 2 minutes later.

  Result: now I'm back to the original combination of 2x2gb. Always deal with the lack of memory and without understanding what's wrong with the new RAM I bought at Fry's. What about compatibility? Is there an another specification? Of course, I know, there may be a malfunction of hardware, but I would like to address this issue before making another run to the store and risking another model or brand.

  For reference: I've tried it before, but because of the lack of information from the seller, I was conquered by a stick of RAM 1x8GB, which is not supported by my model. So I replaced it with the 2 in question.

  Thanks for any help.

  It is generally recommended to stick with quality RAM to buy from a seller that tests and ensures their RAM to work with Macs - the two most recommended are OWC (macsales.com) and Crucial. They both offer helps you determine which RAM you need and offer the lifetime warranty.

  http://eShop.MacSales.com/shop/memory/iMac/2010/DDR3_21.5_27

  That should be your - sure.

  I'll be back on the RAM for a refund.

• Portege R700-19 t - new RAM-&gt; start is no longer

  Hello together,

  so I bought two new RAM sticks for my old laptop
  Toshiba Portege R700-19 t

  But since I installed them, the machine does not start in an operating system more.
  The installed Windows 7 64 bit goes to a black screen before the windows at Startup logo (even in safe mode). And after a few seconds, the fans will quickly but nothing seems to happen.

  The next thing I tried was a (12.04) ubuntu live dvd. But it does not either. No error message or anything, just an automatic restart after a few seconds of black screen.

  The next thing was memtest86 + v4.20:
  It crashes immediately sometimes a black screen and sometimes at this http://i.imgur.com/eJqIyDp.jpg .
  I tested my new two sticks together and alone, still the same problem. The old ones that work perfectly and not crash of memtest.

  In the BIOS is the only thing on the memory and then it sees the correct "Total memory size 8192 MB.
  
  Plug portable-mem from toshiba:

  • Standard: 4 (2 + 2) GB
  • Max Speicherausstattung: 8 GB
  • Technology: DDR3 RAM (1,066 MHz)

  link to the Toshiba product description: http://www.toshiba.de/discontinued-p...tege-r700-19t/

  Cannes-old (work) ram:
  2 x Samsung 2 GB 1Rx8 PC3 - 10600S - 09 - 10 - ZZZ M471B5773CHS - CH9

  new RAM sticks:
  2 x G.Skill 4 GB DDR3-1333 (PC3-10600)
  link to the shop where I bought it: https://www.alternate.de/G-Skill/SO-...roduct/1154622

  In my understanding of both new sticks should work well with my laptop, or am I missing something?

  concerning

  For me, the question is clear enough; the laptop does not start because of new RAM modules.

  The new RAM modules are not totally compatible, or the RAM modules are defective.

  I recommend you test an other modules; for example modules manufactured by Kingston.

• All-in-one HP 3420 new RAM not recognize computer

  Have some computers All - in - One HP 3420 I'm trying to upgrade the memory in.

  There is that memory, two locations so choose which slot for memory is a no-brainer.
  
  Has started with a 2 GB chip slot added another chip of 2GB to
  location B - no joy, computer
  recognized only the slot a. 2 GB
  
  Has taken a 2 GB
  chip on a second HP 3420 & put it in the slot B
  the first computer (just in case I have used the bad memory).
  Still no joy.
  
  BIOS is only say 1 Channel memory & only
  Recognizing that only channel & 2GB memory
  Someone at - it a setting I can verify
  or jumpers on the leading edge that must be fixed in order to recognize the double
  Configuration of channels?
  
  I would be happy if I can still get the systΦme can recognize the
  4 GB, I have in it, either in single or double channel
  mode.

  In case someone else has a similar problem:

  Computer to start

  F10 BIOS & GB of information system to check a single recognized memory

  Exit without saving changes

  When the computer turns off before the reboot, pull the computer branch

  After 30 seconds, plug the computer in, turning on and f10 in the BIOS:

  computer should now recognise the new RAM

• Latest Version causes BSOD

  Hi I read posts about 6.18 aheap version is not compatible with the HP webcam not

  It seems I have the same problem

  There were proposals for links to download 6.16, but none of them work

  I spent hours trying to uninstall reinstall etc etc,

  Very frustrating and a waste of my time.

  Please provide me a link to an older version so that I can continue to use Skype.

  Thank you very much

  http://community.Skype.com/T5/Windows-desktop-client/Skype-6-18-update-error-BSOD/m-p/3522835#M29259...

  If your laptop has the webcam HP HD Webcam [Fixed] installed, this may cause BSOD with the latest versions of Skype 6.16/6.14.

  The solution is to uninstall the currently installed version and install Skype 6.14.0.104 version.

  You can use the like posted download link here:

  http://community.Skype.com/T5/Windows-desktop-client/ASUS-USB2-0-webcam-not-recognized-by-Skype-6-18...

  Don't forget to turn off the automatic updates:

  Tools-> Options-> Advanced-> automatic updates-> turn off automatic updates

• New RAM cards are in the slot on the iMac 27 "late 2009?

  does anyone have experience that new RAM cards does not match the slot to the iMac 27 "late 2009?

  The computer has been identified as an iMac 27-inch late 2009 model correctly?

  In the affirmative - download of database http://mactracker.ca feature - specs are:

  Introduced October 2009

  Abandoned July 2010

  Model identifier (Core 2 Duo) the iMac10, 1 iMac11, 1 (Core i5, i7)

  Model number A1312

  EMC 2309 (Core 2 Duo) - EMC 2374 (Core i5, i7)

  MB952LL/A order number (3.06 GHz), MB953LL/A (2.66 GHz)

  Memory maximum 32 GB (Core i5) or Core i7 real16 GB (Apple)

  Memory slots 4 - 204-pin PC3-8500 (1066 MHz) DDR3 SO-DIMM

  • Installation of memory in an iMac - Apple Support

  Read carefully this ^ support article since there are several different model iMac features listed.

  Processor: Intel Core 2 Duo (E7600, E8600), Core i5 (750) or Core i7 (860) ('Wolfdale, Lynnfield')

  Processor speed: 3.06 or 3.33 GHz (Core 2 Duo), 2.66 GHz (Core i5), 2.8 GHz (Core i7)

  Architecture: 64 - bit

  Number of cores: 2 or 4

  Cache memory: 3 MB (3.06 GHz) 6 MB (3.33 GHz) L2, 8 MB (2.66, 2.8 GHz) L3

  System bus: (3.06 GHz Core 2 Duo) to 1066 MHz or 1333 MHz (3.33 GHz Core 2 Duo)

  -2.5 GT/s (Core i5 and Core i7) or Intel Direct Media Interface (DMI)

  Graphics Card ATI Radeon HD 4670 or Radeon HD 4850

  Graphics memory 256 MB (Radeon HD 4670) or GDDR3 512 MB (Radeon HD 4850)

  Where did you get the RAM and what are the specifications and the brand name?

  • Memory specifications for 'late 2009 iMac 27-inch model' of OWC, macsales:

  http://eShop.MacSales.com/shop/memory/iMac/DDR3_21.5_27

  Two sellers of quality focused on the Mac are OWC, macsales and Crucial.com. You would still be

  to identify the model of computer generation exactly & get quality RAM for them to work.

  And notice the shape of the keyway of the memory chips that they need to be oriented correctly

  in order to fully and properly inserted into the slots. If they are the correct specification for your iMac.

  Good luck & happy computing!

• Satellite L30 10Y does not start with the new RAM modules

  Hello
  regged just with this forum I have a problem to upgrade memory.

  I read through a few problems of memory here and all users that it is a problem of memory comaptible. I got Hynix 512 MB RAM in my laptop and I bought 2 x 1 GB memory Hynix these two are match sticks to the installed memory, but when I installed my laptop wouldn't boot at all. It would only boot if I had a stick in both.

  I tried to switch ports top and btm and even when a stick was installed it says in XP, Vista and Windows 7 (yes I tried all systems) 896 MB of available space. I even tried to use my other Hynix stick, but he won't start and showed more stick of 1 GB (896 MB usable in Windows 7). After reading all the threads I wonder if it is a hardware failure or is there a fix in the world of Toshiba or perhaps in the world of Toshiba, the L series is almost obsolete and not worth to help people who unwittingly bought their goods.

  I apologize for being slightly down on Toshiba but a laptop that shows what he can work and is not a company should hold his hand up and say that Yes, there is a fault and help deal with the problem.

  You see 896 MB, because the rest is reserved for VRAM for graphics card.

  Sometimes RAM may simply be incompatible, because of incompatibilities of calendar or RAM chip/controller design differences.

  What speed and timings is your original RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  What speed and timings is your new RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  You can display this information using a utility called CPU - Z
  http://www.CPUID.com/cpuz.php

• Satellite L30-10 X - where can I get the new RAM for upgrade?

  Hello, world from Toshiba!

  I finally decided to spend my current RAM (2 x 512) memory in better and more useful work 2 x 1024. I'm willing to spend the right amount of money for the best solution and I really wanted to get the upgrade memory on the official website of Toshiba, but for some reason any he does not list my model (L30-10 X) in the list of laptops, in fact I can't find at all.

  Could someone please direct me to a site that sells official Toshiba products, or if you please inform me of a potential market of memory RAM (for example, Kingston, Corsair, PNY) which will work in my laptop?

  Thank you in advance!

  Hello!

  I think that your model is not on the site of Toshiba, because it s an old but why you don't find your model on the Toshiba site, if you want to increase the RAM? Official website of Toshiba, you can order new RAM modules.

  I tried a bit with Google and I founded the part number for 1 GB RAM DDR2 400/533; It s PA3411U-1M1G.
  If you're looking for with Google too you should find a few online shops where you can buy it. Alternative contact you service provider allowed. They also sell new RAM for your laptop.

  And in my view you can also use RAM from Kingston for example. I have good experiences with Kingston.
  As far as I know Toshiba doesn't produce its own RAM. It s RAM other manufacturers like Kingston, but only with another label.

  Good bye

• Satellite L675-10T stucks in a black screen after the new RAM upgrade

  Hi all

  I recently decided to upgrade the memory in my laptop pretty.
  I went online, has adapted Rams and ordered.

  What I got are 2 of them:
  http://www.offtek.co.UK/RAM-specification/Toshiba/Toshiba-laptop-memory/satellite-L675-10T/pid921300

  The installation is very easy, but as soon as I turn on my laptop, it stucks in a black screen with a straight white line underscore.

  I guess it's an incompatibility problem?
  Could you please help me?

  Thank you.

  I think you're right, it seems that the modules are not totally compatible, even if the online retailer page says they are
  You can remove the new RAM modules just to check if the laptop to boot up properly I guess correctly the unit upwards.

  Solution? Use a different RAM modules I had good experience using modules from Kingston, they might be a little expensive, but I think they should work correctly.