New T460s does not start after initial reboot

Similar Questions

• New player does not start after cloning?

  I'm having some problems with my hard drive, so I decided to install a new larger hard drive. I cloned my drive C using Macrium Reflect Free Edition and at first, it seemed to clone OK although I noticed that the old drive was 10mgb of used space is superior to the other.

  When I disconnected my old drive and I tried to boot from the new drive, I had a Manager directed black screen startup (?) asks me to insert a system disk and choose repair. Also, the screen said "boot selection failed because a required device is not accessible."

  When I tried to start using the drive of W7, I got the same black screen.

  If I boot using the old drive I see the new disk in drive F and it seems that all my files are there, and I can access, the data files and the system.

  When I opened disk management, both drives are shown however:

  Drive C (the old disk) Watch - healthy (System, boot, Page file, Active, Crash Dump. Primary partition).

  Drive F (the new drive)) shows only - healthy (active, primary Partition).

  Then of course some files, including the MBR were not copied. How can I copy these files to my new drive so that it starts?

  Thank you

  Tony

  Thank you for that. I had problems to get the PC to boot from the CD using the W7 installation disc but I used the recovery disc Macrium and who recreated the MBR and now everything goes well :-)

  Thanks again

  Tony

• New G770 does not start after installing Ubuntu

  Do not use is not Windows, I just installed Ubuntu on this new G770 wipe all the previous partition in the process.

  Now when you are powering the laptop, the power led lights up, but isn't it, no display, mechanical noises from him, nothing. Cannot access the bios.

  What is the cause and how to fix it?

  Kind regards

  I had a battery problem. Which is fixed now.

  Installation is complete on the Lenovo G770 with InsydeH2O Bios. He managed.
  Here are the steps I followed:
  The disk partition table is TPG. I created a partition fat32 in first position and set the boot flag (partition type is EFI, checked with gdisk ef00 type). Then an ext4 /, year ext4/Home and a sectoral approach.
  The installer told me that with this partition in use table format, I should normally have a separate partition for the boot loader code, also not yet would it be possible to install the boot loader for a partition. I ignored that did not create an and we went to the installation process.
  He filled out. I then installed grub-efi-amd64 and everything works perfectly on this laptop, the system now works fine.

• Windows 7 does not start after reboot.

  I did a fresh install of windows 7 ultimate. Setup was good, he began, updated, installed some drivers and software, tried to reload and bad news. Restarting stopped with a white screen where the startup screen should be. I turn off the cpu and no problems at windows startup. I tried several times and no luck. If the restart from the menu start, it stops at the empty screen. "I seek answers and possibly other charges was installing, disabled all updates and disconnected all the printers, speakers, etc." and again not luck. After that first start and the processor does not start after a reboot. It stays on with a blank screen and no response to keyboard... Help, please...

  I corrected this easy on my HP 7100

  Go to management, records and defined as being active, then fixed, make a right click on the partition with windows on them might have to boot windows disk and choose repair option 2 times I found on a model of friends. Anyway, problem fixed, now able to restart (warm start)

• Pavilion HPE H8-1121: Pavilion HPE H8-1121 - new graphics card + power supply does not start after screen HP (Revisited)

  I have the same problem as this post 2013!  Ouch. Pavilion HPE H8-1121 - new map chart + power supply, does not start after HP screen.

  I installed a new power supply (Seasonic 620W), which works well.  I also installed a GTX 660Ti last year and it was works fine as well.  I recently bought a ZOTAC GTX 970 and attempted to install it, but it will not go beyond the blue HP screen and I get the same code of beeps (1 long, 3 short), who, seems, suggests that the video is not initialized.

  My BIOS date is 2011.

  Where can I find an update for this?

  I'm also using Windows 10, which I found on the HP site is not tested on my model and would probably not favourable to good use.  Should I do back up to 7 or 8?  and then update the BIOS?  Y at - it a update for my BIOS and where can I find.

  In any case, I hope that this is a solution.  Again, this is not a bad machine to be 5 years old.

  Thanks for any help!

  If the video card that you have purchased dose not a legacy vBIOS it will never start. An update of the BIOS doesn't solve that.

  It is likely that your new video card has a vBIOS UEFI and that only is for the PC motherboards newer than yours which have a UEFI BIOS. Your motherboard has a legacy BIOS. 2012 is the year of model when the UEFI BIOS more or less became the de facto on motherboards standard.

  I return it for a refund. Find the candidate of video cards that support the old BIOS. It can be inherited only or switchable vBIOS (legacy or UEFI) vBIOS.  I suggest looking at the site of Sapphire Technology. ZoTac is not known to provide enough information about their video cards in the way. You upgrade a pre-built desktop PC and it's different and a little more difficult to set up a DIY PC. I looked at the site of Zotac and see that nothing is said about their video vBIOS cards.  I would return to the map.  Carefully read the specifications of the video card. A candidate for your motherboard card must have inherited vBIOS support or simply, it won't work.

  ZOTAC (they don't say anything about their product vBIOS)

  https://www.ZOTAC.com/us/product/graphics_card/GTX-970-amp-extreme-core

  Sapphire Technology

  http://www.sapphiretech.com/catapage_pd.asp?cataid=305&lang=eng

  Because you look at game with 4 GB cards. Take a look at the following map. It has a double vBIOS. legacy and UEFI. http://www.sapphiretech.com/productdetial.asp?pid=640A98CD-0CF0-4191-B75C-CA2800111ADB&lang=eng

  

• Photoshop does not start after update CC 2015 and I can't install new applications... What can I do?

  Photoshop does not start after update CC 2015 and I can't install new applications... What can I do?

  If you leave CC 2015 Installer remove older versions of Photoshop you can re - install older versions using the creative Cloud Desktop application or through direct downloads, you can install.

  Direct download links of Adobe CC 2014: 2014 creative cloud release | ProDesignTools

  Download new Adobe CC trials: direct links (no Assistant Manager) | ProDesignTools

  Download Creative Suite 6 applications

• The browser does not start after you have turned off and turned on the computer

  The browser does not start after you have turned off and turned on the computer. I tried to remove the program entirely (as well as personal preferences), to create a new account, install a different browser versions. All this has not helped. (I have Windows 7). Help, please! Every day I have to reinstall Firefox!

  Hello Nastena, try a clean reinstall, some Firefox issues can be resolved by performing a clean reinstall. This means that you Remove Firefox program files and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  Please report back to see if this helped you!

  • Also check if your antivirus or other access security software (firewall, antispyware etc.) blocks firefox.

  Thank you

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• HP DV7-7259nr does not start after the BIOS update

  Hello

  I have a problem with my HP DV7-7259nr laptop, WIN8 running: it does not start after tune recommended to update BIOS and drivers.

  It downloaded all the drivers and started installing at one time, he asked for a reboot, click OK and the BIOS update has begun to load. The process ended successfully and after the reboot that my laptop wouldn't start; everything is black and the cooler is runing.

  I tried:

  -battery disconnected and power - button Power - plugged power again-> NOTHING

  -Windows key + B + Power button--> nothing

  Please help as this is the laptop I use daily in my work.

  Thank you

  If you install the electro mechanical original hard drive in it starts?

  If it has been delivered with a SSD?

  The specifications indicate that an electromechanical drive was part of the specification.

  

  This is where lies the UEFI environment. It is actually on the hard drive.

• Does not start after the reload of the operating system

  OK, this is my story of boredom.  I have a Lenovo T61 Type 6463-5BU, S/N L3-xxxxx.  The hard drive died a few weeks ago, and since then, I have received a replacement drive under warranty, that is the exact same drive type.  We had a backup image of the old system under Norton Ghost and managed to get the image to the new disk once it has been installed.  To do this, we used a utility called OS
  'BartPC '.

  Since then, I did pretty much everything I can think of to get the system to boot, including playing with the BIOS settings, setting the drive to 'boot' and 'active' with the help of a number of public services, including the good old "diskpart" and many others.  The reader will just not start.  A few times I could read the disc using Bart in command prompt mode, but I never managed to boot from it.

  The laptop has a finger print reader, but I was told several times that this has nothing to do with the problem.  So... before I cut off the finger of a person and drag in the player... What am I doing wrong here?

  Note of the moderator; s/n, under the direction of protection own members

  AGoodSolutionideas can save I hope as your image.

  For later use, take a look at this document from Lenovo on the use of Ghost; Partition does not start after being restored with Norton Ghost - NetVista / ThinkCentre / ThinkPad...

  I know it says 'prior to 2004 systems', but it is still topical.

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• Pavilion dm4-1265dx does not start after Windows 7 logo

  My laptop does not start after the "Starting Windows" screen when I try to boot the operating system normally. When I try to run the repair mode from the start nothing happens... I get a blue background image and the pointer of the arrow, but no icons or windows appear.

  I tried the system diagnostic mode by pressing ESC when turning the laptop on and the hard drive test fails every time, showing the following results:

  Test Drive: 1
  INTELLIGENT control: passed
  DST short: failure

  Failure ID: 64RG79-5AP62V-XD6U2K-60RN03
  Product ID: XZ298UA #ABA

  Hard drive 1

  --------------------------------------------------------

  Test drive: FAILURE

  How should I proceed? The laptop is still under warranty, but it was purchased in the United States, and I now live in the Brazil.

  Hello

  You will need to replace the hard drive.

  HP should send you a new drive for free, but in your case is a little complicated as you mentioned it already. Please contact HP tell them about this situation. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

• vCenter Server Service does not start after P2V

  Hello community.

  A problem that I have not been able to solve and looking for help.

  Problem:

  vCenter Server Service does not start after that Windows Server was P2V would be.  We get an ERROR 2 of the Service.  Get the error of the system Windows 7024 event log.

  History:

  The client, I currently work with that tries to smash to the high location of the DEV VCENTER.  Location of DEV vcenter works now all for this site (domains, dns and all development servers).  If its VCENTER PRODUCTION of this location.  Currently, SQL Server (dedicated to vCenter), VCENTER and SSO are all sitting on the same box.  Let's break the SSO, SQL and VCENTER in their own servers.  However, the client wants to re - use the current physical server for SQL Server.  So I need P2V physical server existing until I can start the new environment.

  I was able to get all of the services working on the virtual vCenter (SQL, SSO, Update Manager etc etc) but have been unable to get the real vCenter Server Service works.  Fails every time with the 2 ERROR Code.  I was unable to get a KB of VMWARE item that corresponds to the issue I'm having.  ERROR 2 code has many articles and none have worked.

  Details:

  vCenter 5.1 Build 799731

  SQL 2008 R2

  Windows 2008 R2

  When the vCenter Service tries to start it will stop at the 50% mark and gives this error: (I removed the names for security reasons)

  Windows could not start the VMware VirtualCenter server on <server name>. For more information, see the system event log.  If it is a non-Microsoft service, contact the service vendor and refer to service 2-specific error code

  When I saw the Windows system event log I get this error:

  EVENT ID: 7024

  The VMware VirtualCenter Server service stopped with the error special service that the system cannot find the specified file...

  When I go through the vpxd log file I see this at the end of the newspaper: (I removed the names for security reasons)

  2013-12 - T 03, 16: 08:21.843 - 05:00 [info 09168 'dbdbPortgroup'] [VpxdInvtDVPortGroup::PreLoadDvpgConfig] loaded config VGA objects [0]

  2013-12 - T 03, 16: 08:21.844 - 05:00 [info 09168 "authvpxdMoSessionManager"] [OSP] [SessionManagerMo::Init] Admin URI value: https:// < name of vcenter server: Port #> / sso-adminserver/sdk

  2013-12 - T 03, 16: 08:21.844 - 05:00 [09168 "authvpxdMoSessionManager" info] certificates [OSP] [SessionManagerMo::Init] download m root...

  2013-12 - T 03, 16: 08:21.858 - 05:00 [01440 info "Default"] wire attached

  2013-12 - T 03, 16: 08:21.880 - 05:00 [09168 error 'vpxdvpxdMain'] [Vpxd::ServerApp:Init] Init failed: unexpected exception

  -> Backtrace:

  -> backtrace [00] rip 000000018018977 a

  -> backtrace [01] rip 0000000180100 c 98

  -> backtrace [02] rip 0000000180101fae

  -> backtrace [03] rip 000000018008aeab

  -> backtrace [04] rip 00000000005 b 4971

  -> backtrace [05] rip 0000000000551298

  -> backtrace [06] rip 00000000005516 c 9

  -> backtrace [07] rip 00000000004c0fae

  -> backtrace [08] rip 00000001405bbfb8

  -> backtrace [09] rip 000000013f4b0078

  -> backtrace [10] rip 000000013f4b016a

  -> backtrace [11] rip 000000013f4b0279

  -> backtrace [12] rip 000000013f4b0609

  -> backtrace [13] rip 000000013f7f2903

  -> backtrace [14] rip 000000013ff9e4b9

  -> backtrace [15] rip 000000013ff9835c

  -> backtrace [16] rip 00000001401b8a3b

  -> backtrace [17] rip 000007fefedca82d

  -> backtrace [18] rip 000000007783652d

  -> backtrace [19] rip 0000000077ccc521

  ->

  2013-12 - T 03, 16: 08:21.881 - 05:00 [warning 09168 'VpxProfiler"] ServerApp::Init [TotalTime] took ms 4603

  2013-12 - T 03, 16: 08:21.881 - 05:00 [09168 error "Default"] could not initialize VMware VirtualCenter. Closing...

  2013-12 - T 03, 16: 08:21.882 - 05:00 [09168 "vpxdvpxdSupportManager" info] free/busy information wrote

  2013-12 - T 03, 16: 08:29.280 - 05:00 [00788 WARNING opID "VpxProfiler" SWI-39d3665d =] VpxUtil_InvokeWithOpId [TotalTime] had 12000 ms

  2013-12 - T 03, 16: 08:41.280 - 05:00 [00788 WARNING opID "VpxProfiler" SWI-da6b3df9 =] VpxUtil_InvokeWithOpId [TotalTime] took ms 12001

  2013-12 - T 03, 16: 08:53.281 - 05:00 [00788 WARNING opID "VpxProfiler" SWI-5086bf7f =] VpxUtil_InvokeWithOpId [TotalTime] took ms 12001

  2013-12 - T 03, 16: 09:05.282 - 05:00 [00788 WARNING opID "VpxProfiler" SWI-3abd7c64 =] VpxUtil_InvokeWithOpId [TotalTime] had 12000 ms

  2013-12 - T 03, 16: 09:17.283 - 05:00 [00788 WARNING opID "VpxProfiler" SWI-b9c8c88a =] VpxUtil_InvokeWithOpId [TotalTime] took ms 12001

  2013-12 - T 03, 16: 09:17.353 - 05:00 [info 09168 "Default"] forcing of VMware VirtualCenter stop now

  I pulled the virtual machine in a laboratory and all network problems that would be removed to isolate.  Now the VCENTER is shouting at this topic it can't find one of its guests in the vdxp log, but that shouldn't matter.  All Services have been changed for local accounts.  All network and ODBC parameters are able to see the server... aka the server can see.  I didn't remove any software or drivers for the VM (techniques it is my third P2V to the same server for testing reasons)... And the only thing that won't start is always VCENTER SERVER... SSO is started, SQL is launched...

  Also everything remained the same on the virtual machine (DNS, IP, NAME etc etc). Stop the physical and start-up it upward don't show any problems.  Only when its summer P2V would have done that themselves.

  I can't get this number.  Need help.

  Thoughts?

  Thank you

  BostonTechGuy

  In this case, we have finished rebuilding the vCenter and all migrate on.  Wish had better put up-to-date, but ultimately, it's what has been done.

  Thank you

  BostonTechGuy