New to VMware - problems with P2V

Similar Questions

• Will there be new touch ID problems with iOS 7.1 measures?

  I have an iPhone with iOS installed 9.0.2 6. I was hesitant to go to iOS 9.1 because of problems with the Touch ID reported about 4 weeks ago. Thereafter, who had been an interim update (? iOS 9, 1.1), but I have seen no recent comments. Are there developments in this issue? I note tha iOS 9.2 beta 3 has been released; However, the overview of comments I've seen of the 'new' address for the iPhone elements, but says nothing about the contact ID. Any news?

  I used each publication IOS 9 so far. Never had a problem with TouchID. And I have not seen much on this forum about people with problems so, whatever it is, it probably wasn't terrible together.

• New and strange problem with Rhapsody to go on my Sansa Fuze

  Have a Fuze with 8GB micro SD 8 GB card inside and use for a long time without any problem with Rhapsody. Recently, I had not synchronized for a long time and got the message to play the tracks of my subscription, I need to sync with Rhapsody. So I don't tell me, no problem, and I do. The synchronization works very well and I get the message Rhapsody, it's reading the tracks on my Sansa and I get the message that it updates the internal memory on my Sansa. Then everything is finished and when I click on the internal or external memory, Rhapsody, I get the message that all is well and she sees all my Sansa great Flickr photos. I even put a couple of new albums of Rhapsody on the SD card in my Sansa. Once again, no problem.

  BUT when I disconnect the Sansa (again once, normal behavior with the green bar on the Sansa screen and the message it refreshes my media), he always says I have to synchronize to play the tracks on my subscription.

  Have tried resetting the sansa, tried the sansa when logged in to rhapsody, but nothing seems to solve this problem of license. How can I fix?   Thanks a lot for your help

  Ah, I leave you with the secret handshake to reset the secure clock.  Normally, this is done in this last step, when you transfer a track to the device.

  Open the client Rhapsody 4 and plug your rocket.

  Now for the tricky part.  Crack the knuckles and fingers ready.  Press and hold the [CTRL] + [SHIFT], then right-click on the "rocket" in the Sources pane.

  There you go.  Select Reset secure clock.

  See if the device is now happy.

  If all else fails, use the Format command on the "rocket", which will erase all media device, and then start over by allowing first and transfer some test tracks.

  My theory is that something is wrong with your secure clock...  Let me know how it goes!

  Bob

• New iMac, retina - problem with the mouse in Windows 10

  Hello - I have received yesterday my new iMac of retina and transferred the VM Fusion with all the new Mac tips. Everything has gone well so far, but after setting the parameters for the new options of the retina, the mouse doesn't use VM Ware Tools. I reinstalled the tools, but I had no change. Yet the mouse is slow and I cannot leave the window of Fusion as it used to be. For any help or suggestion would be greatly appreciated. Thanks MK

  Please, try the following steps:

  1. remove the existing tools of the VM of the Panel--> uninstall a program

  2. restart your virtual machine and install the VM tools grouped.

  3. If the problem persists, make sure that the preference of mouse in VMware Fusion--> preferences--> game is NOT set to 'always optimize the mouse for games'

  Kind regards

  -Rick

• New UCS-C210 problem with video monitor output

  Hi all

  We just bought a new Cisco UCS C210 M2 product for our CUCM migration to Virtual Machines. We plugged a HP monitor and a USB keyboard to start work with the UCS. Then we plugged the server to the power supply and turn on the server, the fan worked properly for his initial shot. However, I could not see the monitor up and I can't see if it boots correctly. We waited and notice that the keyboard seems to work as you can see the num and lock the scroll works.

  I unplugged the monitor of the connection of the console before the use of the foxconn connector that came with it and plugged into the DB15 port on the back. Same result the monitor does not display anything.

  So I went on the second UCS server using the same keyboard and mouse, everything works.

  Any who know this problem of the screen does not? If so, please share how to fix it.

  Otherwise, our conclusion would be that Cisco sent us a faulty hardware or it has become defective during the transport.

  Thank you best regards &,.

  Ramon

  OK fans turn upwards and then downwards with the lights on the front would indicate to me that the server itself is ok and boot up normally. The fact that you have used this monitor UCS one another in the same way seems to indicate that the problem is probably with this server and a video on the issue. I suggest to open a TAC case and include these steps you have taken. If you can, try reinstalling all your memory and boot up the server again.

  I hope this helps.

  Sent by Cisco Support technique iPhone App

• Cannot create a new layer (was: problem with programme)

  Flash CS6 doesn't let me choose text tool... computer laptop asus

  Create a new layer.

  Select the text tool.

  any problem?

• New at first - problem with the timeline of aid.

  I can't drag anything in my time lime. He is blocked because I do not know why, it is mentioned: timeline (not of sequences). How to unlock this please?

  Try the NEW ELEMENT process described in the pages of tutorial links

  The list of the body message #3 http://forums.adobe.com/message/2276578 tutorial can help, with more help in the message #5

• Printer HP C509a range: new/still a problem with the C309a with wireless printing

  Printer is now, do not print, then all the sudden days later, it will print what was in the reference. I checked everything I know how to check. I think to unstalling the software, but when you do that... There is ALWAYS something that lingers to create a problem during the installation again. Is there a good way to get rid of the computer of all the files that relate to the printer?

  OK, here's where I am. Computers 3 1 HP printer. I removed the HP software. Reinsall after I did the "usbready.exe" file in order to load the software.

  http://h30434.www3.HP.com/T5/printer-software-and-drivers/C309a-software-will-not-install/m-p/5476271#M79658

  FYI

  1 computer is wired 150 ft. - works fine. The other 1 computer (wireless router) to the point of HP printer

  works very well. It is the 3rd computer wireless to the router but does not work. The software, see TI but not install and plug. In one of 3 different choices. Now, I got a little my limits. I'll try to go in the "devices and printers" see on adding a printer and see if that can cling to the top. He is a friend and 24 far mi but needs to be done. The choice of HP software is the USB connection, Ethernet connection and wireless connection. All 3 see the printer but do not begin upward.

  Get it!... see red

• 2910al - 48G Switch: problem with the VLAN

  Hi all,

  I write a new message because I don't know what is happening on my SW series 2910al - 48G and v1910 - 48G.

  I put on the main core SW VLAN 610 and I put to this VLAN IP addreess 100.110.10.1 24-bit etc and it worked fine until yesterday. I change only PLEASE and I enebale STP - loop protect for ports in the range 1-52. (now I rolback this settings as was before)

  

  STP configuration

  

  Now, every PC that has for a long time what IP range 100.110.10.1 24-bit works fine, but new PC have problem with to get the new IP address. I tested it add a static and same address does not work.

  Introduced in second v1910 SW - 48 G VLAN as below

  I connect this flexible switch this \port SW 2910 - G 48, 46 (Vlan 610 tag) <>- at v1910-48G\ port 50 SW (Vlan 610 tahgged) other ports on this switch I put not marked.

  Configuration file for sw v1910 - 48G looks to below:

  #
  activate default domain system
  #
  LLDP enable

  #
  domain system
  disable the access limit
  Active state
  Disable Idle-cut
  self-service-url disable

  #
  rstp STP mode
  enable STP
  #
  NULL0 interface
  #
  GigabitEthernet1/0/1 interface
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/2
  access port vlan 610
  #
  interface GigabitEthernet1/0/3
  access port vlan 610
  #
  interface GigabitEthernet1/0/4
  access port vlan 610
  #
  interface GigabitEthernet1/0/5
  access port vlan 610
  #
  interface GigabitEthernet1/0/6
  access port vlan 610
  #
  interface GigabitEthernet1/0/7
  access port vlan 610
  #
  interface GigabitEthernet1/0/8
  access port vlan 610
  #
  interface GigabitEthernet1/0/9
  access port vlan 610
  #
  interface GigabitEthernet1/0/10
  access port vlan 610
  #

  #
  interface GigabitEthernet1/0/49
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/50
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/51
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/52
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1

  etc...

  Could you help me when I made a mistake?

  THX

  The problem was that solve this problem.

  I have blocked all ports. It was a problem. I change several settings and everything works well.

• Problem with keyboard with T410

  Hello

  For your information:

  for the last 4 months, I have a T410. The laptop came with pre-installed win7. Currently it runs also Debian Squeeze in dual boot.

  The problem:

  In the last few days I have a behavior strange experierenced of the keyboard integrated. The c and e keys d seem to trigger the bad events. e a for example increases the volume, mute d. First of all, the problem is sporadic, so I even if it is caused by dirt or something similar, but currently it is not possible to work on the laptop without an external keyboard (which works fine). I think a bad configuration of the keyboard layout can be deleted, because the behavior is on both systems. Maybe some else has experienced this problem and can help me? I need the laptop for my studies - thus given to maintanance is the worst solution.

  With greetings from the Germany

  Sandrine

  Hi and welcome to the forum!

  See this thread:- http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/Problems-with-the-keyboard-T410/m-p/288630

  I'm sorry, but you will have to go thorough worst-case scenario as it appears

  Keep us however.

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.

  

• Problems with the VMware vSphere Client

  Hallo

  I have problems with the new Client VMware vSphere.

  Until I installed the new client on my system, I had the old VMware inferstructure 2.5 client to manage my esxi.

  I was then going to test esx 4 box of the anther and then installed the vsphere client.

  But!

  When I try to connect my old esxi 3.5 or the new esx 4 I get the following error from the vsphere client:

  "Analysis of the server"192.168.2.2"" clients.xml"file error.

  Logon will continue, contact your system administrator.

  I then clik Ok and get this message:

  The initializer for type for 'VirtualInfrastructure.Utils.HttpWebRequestProxy' threw an exception.

  I tried to delete the old client and the new and then install the new, but still it dosent work.

  I am running Windows 7 64 bit.

  It will not work on windows 7, period.  You must run the VIC from a supported operating system

• New on VMWare... Login and password problems

  Hi all

  I inherited a few major COMPUTER disasters with a client. I'm new to VMWare and have found that several virtual servers are no longer running. We have pay to this topic. When I run the Home Page of VMWare Server it takes me to VMware Infrastructure Web Access with a login and password, but I have no idea what could be. The person who set up the system is not reachable. Is there a way to identify and fix this mess?

  Thanks in advance.

  Rob

  Please reward points - we must know if we helped.

  Click here to solve the problem-[http://communities.vmware.com/docs/DOC-9390: d-9390]

  Click here for the manual http://www.vmware.com/pdf/vmserver2.pdf

• Problem with the new hardware wizard and PCI bridge PCI to PCI standard

  I have problems with VMware Fusion 2.0.2 on my MacBook Pro (Mac OS X 10.5.6).) The guest from Windows XP Pro (SP2) Found New Hardware Wizard keeps wanting to install a software for "PCI standard PCI to PCI bridge". I tried to do 'automatically' and "install from a specific location" using the Windows disk, the MacBook Pro and the Mac OS X disk. In each case, I get the message 'not succeeded the Windows Logo test'. If I click on "continue anyway" is seems to load pci.sys to C:\Windows\System32\drivers. I click 'Finish' in the last window but it begins the loop again and again and again. The virtual machine network adapter is set to NAT and everything seems to work fine, but I can't stop this annoyance. Any ideas?

  There are 32 of these devices.  How many times have you finished yet?

• Anyone having problems with the new iPhone LTE connection 7 on Verizon?

  I am now on my iPhone second 7 with Verizon. I had four phones for me and my family. I have now had issues where I have no signal in the same areas where my signal allows to be strong. I can't solve the problem with the activation/deactivation of the airplane and then mode again in normal mode. My phone will rest with no signal for 5 minutes, then going to LTE with three bars. I also had the problem where I had only 1 x signal, while my son standing right next to me has LTE. And he had the same questions, where I'm on LTE and it gets no signal. I use to have LTE where I live and work all the time, now it's spotty at best. Apple has replaced me and my sons iPhones but not luck. Still do. Any ideas or an any other suffering?

  (1) go to settings/cell phone/cellular data Options/enable LTE and select ONLY the DATA. This seems to solve the problem (as a temporary solution) for most of the people affected by this problem. The bad part is your request might not be as clear (since they cannot use the highest LTE signals) and you can make calls and data at the same time. But it does not solve the issue.

  (2) there are rumors (but you didn't hear that from me that we only are not supposed to discuss beta software program Apple in this forum) that the new version of Apple Beta for iOS (which also includes an update of the software carrier Verizon to 26.0) seems to solve this problem. So, there's a light at the end of the tunnel.