NI 9472 comunication problem

Similar Questions

• ENET-9472 installation problem

  During my first attempt at installation of connection to NOR-DAQmx, NI ENET-9472 (whose installation takes place without incident), there was a deadlock:

  In step 6 of the Configuration of the device (p.8), say the instructions enter the hostname under general settings of the network. This field is not accessible - I can't type in this empty field, so I can't finish the configuration. left/right clicks do not open the field. The Self Test, reconnect and Reset device function. The icon displays as connected ENET-9472. Everything was new, out of the box, and all instructions proceeded without error up to this point.

  YES! Thank you. He was so weak, I missed it!

• Whit SSL Node Manager comunication problem

  Hello, I have a problem whit node Manager (SSL protocol).
  
  My configuration is:
  
  HOST A (contains the administration server and managed_server1)
  The HOST B (contain managed_ server2 in the cluster managed_server1 of Pentecost)
  
  When I startup scrip to HOST B starManagedWebLogic.sh managed_server2 Pentecost all right (. / startManagedWebLogic managed_server2 http://HOST A: 7001). But I can not start the managed_server2 in the Administration Console (HOST A) (using the associated Manager node of Pentecost a suitable machine).
  
  For the server managed_server2, the Associate Manager node machine computer2 is not accessible.
  All selected servers are currently in a State that is not compatible with this operation or are not associated with a Node Manager running or you are not authorized to perform the requested action. No action will be taken.
  
  I find the following:
  
  javax.net.ssl.SSLKeyException: security alert: 090482BAD_CERTIFICATE received from server1.das.cites - 46.34.5.15. Check the peer to determine why it rejected the certificate chain (trust CA configuration, check the host name). Debugging SSL monitoring may be necessary to determine the exact reason that the certificate was rejected.
  
  When I go into the Administration Console to:
  
  Machine-> Computer1-> monitoring:
  Status: available
  Version: 10.3
  
  Machine-> computer2-> monitoring:
  Status: Inactive
  Description of the problem: javax.net.ssl.SSLKeyException
  Version: (not available)
  
  How I can solve this problem. Thanks for any response.

  Try to start the server with the property weblogic:

  -Dweblogic.security.SSL.ignoreHostnameVerification = true.

  Please also enable debugging for details indicators:

  -Dweblogic.security.SSL.verbose = true
  -Dssl.debug = true
  -Dweblogic.StdoutDebugEnabled = true

  Thank you.

• Problem of comunication GPIB (Tektronix TK2465)

  Hello, I'm quite new with labview and I have a problem with the GPIB communication; Dealing with a Tektronix TK2465BCT, I plugged a GPIB-USB-HS to my PC Windows8 adapter, when I try to communicate with the instrument via NI MAX seems to communicate properly, or at least that it is recognized by the PC on the correct address, as soon as I start a VI downloaded from the page of the pilot of the aircraft it detects not the oscillocope. Any idea? Thank you.

  It is a very old and unsupported. I have not downloaded so I don't know if it uses VISA or GPIB low-level functions. You specify a name, address or the resource before you run it? What is the error you get?

• writing in shared variable published network hosted on rt (defined as slave modbus for crio) problems

  Hello Forums or

  This is my first post on this forum and I've been using labview for about 8 months now

  I have a problem about writing data in the modbus registers through a server of e/s defined as a slave modbus for my hardware 9074. Once I finished the project of construction and deployment of the variables and by following the instructions here , he reports no results but a row of zeros. I have the DSM nor opened and configuration modbus master to see whether the data is actually read or written on the respective sides that give the same line of zeros so.  What I am actually trying to write is a single-precision floating data table. The registers are structured F40000-F46534 runs from 10 items or have them for range AF40001L1-AF46534L1 of the AF40001L10 point where it's an array of length 10. (Referenced beaches here)

  I know 1 thing for you, the modbus connection works and is ready for data requests, I tested cela NI DSM and set manually the data for and received my master.

  System and project specifications

  Windows 7 operating system

  LabVIEW edition development system complete 2011

  No module Labview DSC, but I use the real time such referenced by one of the documents

  This project is an application in real time with fpga mode (and not scan interface)

  The master and the slave are the same network and subnet

  Connection Modbus type: TCP

  9074 compact slots rio 8

  9234 module x 3

  module 9221 x 1

  9472 module x 1

  Engine service Variable shared running on windows os and rtos system

  Used this guide to learn more about the Protocol modbus, as I have searched all over the internet to learn more about modbus

  I already have software Modbus IO Server installed on the crio thanks to max or 1.8 for NI RIO 4.0 version

  file attachment (s)

  Image of software specifications Crio

  Image of data written in scheme-block rt variable

  Short version of the problem: why is the e/s no variable writes in with the converted correctly data?

  Okay, Yes, it's that I was the one proposed. Regarding the news of the error, if you look at the bottom of your image to DSM, you see a little commfail and an error code, but it seems that those are OK.

  The only thing I can think is that DSM (or another function) is written for a range of values that includes 400004. I suggest you to put into service 4-going to a range of 3. 3 s are entered only (perspective control), then you can be sure that the master is not trampling on the data. Once you have checked that, look at DSM and any other code running to make sure q EU not accidentally write 0s to the same reg.

• Problem with the generation of two internal counters pulse trains

  Hello

  I do a control of temperature for two heaters, OR 9472 (output module digital), NI 9271 (RTD for measuring temperatures) and cDAQ-9174 chassis. So, I use the internal meter NI 9174 to generate two pulse train on the outputs (I tried with both cases-> pulse continuous and finite). Before that, I have two separate PID.vi, in which each sent the percentage of cycle of obligation for the two tasks of pulse generation (I configured these tasks with the physical channel cDAQ1Mod1/ctr0 and cDAQ1Mod1/ctr1). The problem is when I run the program, because the application initially worked fine, but after a few seconds the communication between the chassis and the application is not respected (no error message, but the external LEDs on the NI 9472 module had been disabled and stopped too NI 9271 module temperature readings). Then I tried to stop it with a 'Stop' button, but nothing happens. After, I abandoned the race and still nothing happened. So, I finished the Labview program with the Task Manager and a message appeared "reset VI: xxxxx". Finally, I have to restart my computer to run the program again. Can anyone help with this please? If you need more information, let me know.

  Kind regards

  Hi Luis,.

  I have the error cluster connected. But I solved my problem in a different way. I don't know why, but when I configured my RTD module with the DAQ assistant to test some of my design in a new file in VI, the RTD module works fine, but if I copy the entire program logic (include my DAQ assistant) back to my main VI folder and run the application, only for communication between my DAQ hardware and my software works there shortly. So I solved my problem set up any device or module in the same file from the application again and problem disappears.

  Thanks for your help.

  Luis C.

• Spectrum of HP X 2 - HID SENSOR COLLECTION driver problem

  Hello

  I just bougt garage a Ultrabook of spectrum HP X 2/tablet.

  Since I already have a Windows 8 N Pro license I installed it on my spectrum X 2.

  The question I am now face is that the dirver HID SENSOR COLLECTION is not woking and I can't use my sensors such as: rotation (accelerometer), light sensor, the screen...

  I can see this error in Device Manager by double-clicking on the HID COLLECTION of SENSOR:

  "

  This device cannot start (Code 10).

  The process hosting the driver for this device was completed.

  "

  I have installed all drivers HP of my spectrum HP X 2 page drivers and I also installed all Windows updates.

  Can someone please?

  Thank you

  Mircea

  I found a solution for the problem of driver HID sensor Collection.

  It seems that the driver uses something Windows Media Framework and because it can not find it on my spectrum X 2 it fails.

  This driver problem will happen on all the HP spectrum X 2 who have installed Windows 8.1 Pro N (N is the European version) because there is no Media Feature Pack installed by default.

  To fix the driver HID Collection sensor problem, I installed the Media Feature Pack for N and KN here 8.1 Windows versions:

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=40744

  After the instalation just sensors begin to work.

  It is a BIG PROBLEM and HP needs to do something about it!

  A big thank you to Wiab of Lenovo Comunity forum for us to share the solution:

  http://forums.Lenovo.com/T5/idea-Windows-based-tablets-and/yoga-13-hid-sensor-collection-Auto-rotate-functionality/TD-p/997095

  Kind regards

  Mircea

• Problems with arduino labview Interface

  I have the labview-arduino interface, but the problems came when I run the program, sometimes it work perfectly, but sometimes (almost all the time), I can not connect this time, the series of programs and do not show any kind of problems, I can see that in the resourse computers two visa, I don't know if it's because she I soppose comunication , but my arduino do not work, and I can use perfectly with the arduino IDE, but not with VISA, I used the Arduino IDE to be shure that works my Arduino board

  so if you know how to solve this problem, please help me!

  Thank you!

  There is no need to host files somewhere else.  Feel free to download on the forums and attach them to your message.

  Minor first comments.  Why are you re-reading your every 2 seconds config file?  Expect you to change?  If it is then played once and not proofread.

  I think it would be better if you stopped when an error occurred, you can do this by wiring to the RO error enter the stop condition, or use the arithmatic composed with gold.

  But I think the main question you have, it's that your Arduino reference may be whipped out if you do the wrong things.  If your equal comparison is false, you go to the wrong case, where you are not passing the arduino reference.  So when you go to close you don't close your reference and your equipment will always be open, and you try to run again will result in an error.  For even if your loop runs for 0 iterations your reference is lost.  An updated version, which has some of these changes is attached.

• written boolean unique to the module of digital output or 9472

  I have a vi who writes in both modules of analog and digital, 9263 and 9472.

  I don't have a problem writing to the analog modules, but the modules digital (9472) gives me problems.  I want to write a single Boolean value, and he wants a Boolean array.  I was using the DAQ assistant, but dropped on it.  I'm probably not understand how to access the port correctly.

  I've included a partial copy of the code.  (LV crashed when I tried to create a snippet of the original code, so I had to copy it to a new vi.)

  You have not included the Subvi and if you want to generate a single Boolean value, it is absurd to use the Dig generate 1 D data and instance of DAQmx writing. Just use 1Line 1 point. Change the instance by clicking on the polymorphic selector under DAQmx writing. Select Digital > single channel > sample > Boolean. You can also use the DAQ Assistant by plugging in just a function table built between the Boolean command and the input of signals.

  You must also consider writing your code without globals.

• NOR-9472 and SMC solenoid valve

  Hello

  I'm writing the code for the valve of the SCM activity. I need to control the amount of time that the tap is open. The tap is connected to the / 0 on the NOR-9472

  Don't know how to start the problem.

  Second, I want to save data to an accelerometer in the VI even.

  Yet once again, don't know where to start. If someone could please tell me some examples, it would be fantastic.

  Here I have two screws, one to control the faucet, the other to the data recored, separate and have them both in an another vi?

  See you soon

  K

  I wrote code examples that if everything will work well for you, or at least give you an idea of what I was talking about.  There are three cases

  -Wait, the VI is waiting for to press you the fire button

  -Acquire, the VI changes the value of the solenoid valve and starts the acquisition of the accelerometer for a period of time

  -Analyze, the VI performs an analysis of the data and then returns to the waiting state.

  http://decibel.NI.com/content/docs/doc-8596

• Relay control using cRIO LabVIEW and the NI 9472 c series module

  Hi all

  I try to get my program to run so far without success, and need help.

  I use the compact rio with the program on labVIEW and the NI 9472 digital output module. I enclose my VI.

  Basically, it's a test program to run an algorithm at a time. If I use a solid state format to get a time warp that dictates, time of execution of the algorithm. The operation by default, I put is for when the time channel produced a fake.

  Question 1: The problem I have is that even if the time string is true, as it does not run. It remains in State sending false so only of false signals to my relay (which is represented by the round LED - relay switch a solenoid on and outside).

  Question 2: If I can get 1 problem solved, the next step I have will be executing the same algorithm, but for more than a State of time. For example. "06:00" run algorithm. I want this algorithm to keep running as long as he sends signals REAL (which means the solenoid valve remains open until a WRONG signal). Then he will run again to say '08:00 ', execute the algorithm as long as he sends signals REAL and so on...

  In summary -.

  -I want to order a relay (which controls a solenoid)

  -L' use of components listed above

  -With the help of semiconductor in labVIEW (VI attached)

  -At different times, the execution of the algorithm UNTIL sends the WRONG signal and then return to the default state, which means that his waiting until the time channel product TRUE.

  Any help would be appreciated.

  Kind regards

  William

  something like that...

• CS6 InDesign printing problems

  Having looked at the forums and found Adobe support less helpful as I am jumps that the comunity will be able to help me on these frustrating issues.

  We are conducting a number of issues while trying to print from InDesign CS6 on our printer OKI C830

  Our facility:

  OS: 8 64-bit Windows

  InDesign CS6 version: 8.0.1

  Printer drivers: PS: 1.2.0.0 & PLC: 1.0.7.0/1.1.7

  Printer: Oki C830 256 MB RAM / V1.16

  Problems when printing from InDesign:

  • Printing multiple pages causes an error - undefined offending command stack error
    • After printing the first page with success, we get the above error.
    • I've implemented the fix described in the following link: http://forums.adobe.com/message/2878922#2878922
      • Past the binary to ASCII - this helped as we could then print one or two pages if necessary.
  • Booklet printing - when you try to print a brochure, it seems that the broadcast is not understood by the printer
    • Try to print a booklet of 6 ID, pages are printed on a single sheet of A4/3 of the book at random.

  As a work around us are fourced to create the document ID CS6, and then expoort to ID CS4 for printing.

  Also as a side note, I tried printing of our old HP printers and they work fine. Also, this question was present on Windows 7 x 32 institutions.

  Thanks in advance for any help provided.

  See you soon,.

  Matthew

  OK, this is either a problem in the file, or something about the print booklet setting. You can print the file without booklet print to the Adobe PDF printer? If you can, we explore the booklet printing settings. If not, see Adobe Community: file crashing on exit - print/PDF/other for troubleshooting techniques.

• Problem with setwhereclause stripped method - error Houston-27122

  Hi Comunity I'm new in ADF BC and Jdeveloper I'm trying to create an implementation of my VO with many different methods is the filter using this.setwhereclause ("miCustomFilter");
  It works well, but when an onload jspx page appears the following error.
  
  Houston-27122: error SQL durante the circus of the sentencia.
  
  Any suggestions, thanks.
  
  Published by: user10243802 on 10-Aug-2008 14:28

  Hi user

  Your problem is very common in your paycheck VO the SQLStatement
  and change the positional style of binding for JDBC.

  Good luck.

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.