OfficeJet 150: Drivers for HP Officejet 150 (mobile) will not be installed

Similar Questions

• OfficeJet 6700 Wireless will not be installed

  I tried to connect my officejet 6700 without cable.  I am able to get the printer to connect to my network and when I print a wireless network test, it says that it is connected, switch on everything.  I am able to ping the printer as well.  At first when I tried to set up the printer, my computer could not find the printer.  Now, it seems that it can find the printer, but it will not install. I used the HP print and scan doctor, and he said that I had to install the full version of the software that comes with the printer. I tried to reload the software that came on the disk with the printer, and will not install successfully.

  Hi Wally,

  Thanks for the reply.  I am running windows 7 professional 64-bit.  He just said "installation failure," anything else.  Since my last post I was able to chat online with an hp support person, and they made some kind of a work around.  Instead of trying to install as an officejet 6700, installed the driver for a deskjet 6950 and added a protocol TCP/IP port with the IP address of my printer, and that seemed to work.  It is now printing from my computer and my iPad.

• Update cumulative security for internet explorer 9 for windows vista for systems x 64 (KB2792100) will not be installed.

  WindowsUpdate_80073712""WindowsUpdate_dt000"will not install this critical update...

  Hello

  Thanks for posting in the Microsoft Community forums!
  I understand that you are facing problem in installing Windows update. To fix the Windows update problem, try suggestions:

  You did changes to the computer before the show?

  Method 1:
  You can try the steps in the link and check if it helps:
  Windows Update error 80073712

  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80073712

  Method 2:
  Try to manually download the update from the link:
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=36593

  Method 3:
  If the steps above don't you then try the steps in knowledge base article:
  Error code 0 x 80073712 when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/957310

  Note: before performing an upgrade on the spot, you can perform the clean boot.
  Disabling Anti Virus software.
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.
  Also save the data as a precautionary measure and disconnect external devices

  Answer to us if you have problems with Windows Update or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

• Drivers for my new mp3 player will not install. I tried everything I can think of without success. The wizard's message is "a facility of service in this INF is invalid.

  I suspect that the drivers on my pc of 8 years are not up-to-date.  Is all the same to unravel without purchase of this internet software?

  Thanks for the replies, I managed to solve this problem by uninstalling the Philips Songbird software provided with the unit and using XP and WMP Device Manager.  Of course, a conflict between the supplied software and my pc system.

• Multimedia offers for the center of thinking will not be installed

  Hello

  When I try to install multimedia offers for thinking through the Lenovo Update Manager, I get the following message:

  "This program can only serve as a material that is not connected to this computer to control."

  P.S. The DVD - RW device be part of my laptop

  Problem was with diamond tools. I installed Dialomd tools light and it emulates DVD-ROM in the drive 'E '. Installation tool was so stupid and reads the information on this device and not from all the devices set up. DVD-ROM who required for the installer name "D." My friend has a Blue-Ray device and it was unable to install your software up to disconnect it from the laptop.

  I had too many problems with the lenovo software! Last time die software Lenovo until I disconnect all mapped network and created subst drives.

  My conclusion: Jesus Christ, if Lenovo develops cannot iterate the drives in windows, download types and other information about them. So I can send them links to MSDN and examples how todo that!

• OfficeJet 4500 G510g: OfficeJet 4500 G510g will not print full page

  I'm having a problem that gets worse.  My OfficeJet 4500 G510g will not print a full page.  I have installed the latest updates, verified that it's the default printer, aligned the cartridges 2 or 3 times, cleaned the printheads of 2 or 3 times. but no success in getting it to print an entire page

  Hi @thrandall,

  Thanks for getting back to me.

  My suspicion was correct, there is a hardware problem with system of distribution of ink or cartridge.

  Have you tried these steps in my previous post?

• HP Officejet Pro 8500 will not send or receive faxes

  HP Officejet Pro 8500 will not send or receive faxes. 'Run Test Fax' indicates that everything passes.

  Then see HP support pages for your model, its their equipment & the fax is independent of the victory

• My new HP Officejet Pro 8600 will not analyze superior at 300 dpi of the location of the single document.

  My new HP Officejet Pro 8600 will not scan more than 300 DPI when scanning individual photos on the glass plate. I do not use the document feeder. I use this printer wireless on an iMac and a PC.

  Hello

  You can pass the value of hp scan: launch of the demand application, select the shortcut to scan (PDF or JPG to the left) and change the resolution you want and save.

  This will send down the printer settings. So the next time you scan, the printer uses these settings.

  Good impression.

• beatsaudio all in one office: drivers for broadcom WLAN dual band do not install

  After the upgrade to windows 10, I checked the updates from Microsoft and HP through the HP support Assistant.  All updates installed HP exceptiont for 'dual-band Broadcom WLAN drivers for Windows 10'. It will go through the controls and good download.  I retried several times after you restart the computer.  Also do not install is Office XP Service pack 3 - microsoft updates.  Error message 0 x 80096004.  I was wondering if I missed something.

  Hello

  I seemed to have solved my problem with the installation. I went on HP website and download drivers page

  http://WWW8.HP.com/UK/en/drivers.html

  then I went through the features of the device (I put in my model number product after choosing a couple of options).

  This led me to a page showing a photo and a description of my all-in-one and below and on the left side who has been

  Solution and Update Finder

  • Troubleshooting
  • Software and Drivers 3
  • How
  • Product information
  • User guides
  • Video tutorials
  • Several Support Options

  Solution and Update Finder

  The update and the Solution finder scans the connected HP product that you use to identify and recommend possible solutions:

  • Software and firmware updates or missing drivers
  • Errors and hardware problems

  Find Solutions

  How to install the software and collect HP?

• Drivers for a Deskjet 3050 J610a will be dependent not on a HP PC with Windows 7 (64 MB).

  Drivers for a Deskjet 3050 J610a will be dependent not on a HP PC with Windows 7 (64 MB).  Went through all the steps of self-help without result; any suggestions?  Thank you.

  OK, I wanted to just make sure the correct standard troubleshooting had been done. Because it does not sound like a system problem (this is why a system restore has been previously recommended), I recommend that you try a tool launched by Microsoft called Fixit. See the link below for more details:

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

• OfficeJet Pro K850 will not stop print an alignment Page

  Hello world

  I had not used my K850 printer for about 6 months, so when I need to print something with her, I ran the option first cleaning the print head.  I had to run to the top through the three levels in order to get their own.  After this for good measure, I ran the head alignment utility.  The problem occurred during the alignment.  For some reason any he will not fulfill the alignment process.

  No matter what I tried the printer can print the pattern of alignment at all times using only the black and yellow inks. Even if I stopped, remove the power cord and restart, after that it goes through the boot sequence, it begins in the same page with the two same printing inks.

  I managed to interrupt long enough to install the latest firmware but the problem still remains.  In addition, in this case weather or not, it is connected to my computer, so I guess the problem is in the printer, not the driver.

  Any suggestions would be most appreciated.

  Thank you

  Hi there curley2003,

  This article should cover the problem you are experiencing. These measures help and tell us if it helps:

  Manually align the

  Control Panel

  Use the following steps to align the print head using the control panel:

• For Windows XP (KB2719985) security update will not be installed. The text "a problem on your computer is preventing the updates being downloaded or installed" is reported

  For Windows XP (KB2719985) security update will not be installed. The text "a problem on your computer is preventing the updates being downloaded or installed" is reported. Fix - it crashes too much with the line "invalid command line" when I try to run it.

  Hello

  1. this problem occurs only with this particular update?

  2 did you change on your computer before this problem?

  You can follow the suggestions and check out them.

  Method 1

  You can reset the Windows Update components.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.

  How to back up and restore the registry in Windows XP

  http://support.Microsoft.com/kb/322756

  Method 2

  You can read the article.

  You cannot install some programs or updates

  http://support.Microsoft.com/kb/822798

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.

  How to back up and restore the registry in Windows XP

  http://support.Microsoft.com/kb/322756

  Method 3

  Step 1:

  Place the computer in a clean boot state.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  a. click Startand then click run.

  b. type msconfigand click OK.
  The System Configuration utility dialog box appears.

  c. click on the general tab, click Normal Startup - load all device drivers and servicesand then click OK.

  When you are prompted, click restart to restart the computer.

  
  Step 2:

  Download and install the update from the link.

  Update security for Windows XP (KB2719985)

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=30282

  See also:

  Solve common installation issues in Windows Update, Microsoft Update and Windows Server Update Services

  http://support.Microsoft.com/kb/906602

• Photosmart Premium C309-g: the drivers and the printer software will not be installed.

  My network all-in-one Photosmart Premium C309-g worked very well on my desk until recently, when suddenly the HP software could still see and connect to the printer, but Windows 10 could not. I tried to remove the printer and uninstall all associated software, then tried to reinstall the software. Unfortunately, the installation will not get to the point where it starts and then suddenly disappears with no trace of her still running in the background. I can deviate from the default installation and bring to the top of the page to select the components that I want to install, but when I do the button 'ok' on this page does not work. No matter how many times I click on it, the page remains open and the installation will not so fast. If I click Cancel on this page, it disappears and the installation back to the previous page, where I can choose to continue and happen almost immediately out of sight again. This happens whenever I try to install selected software and drivers. I deleted the printer from the devices page in the Panel, I made sure to this it is not is more listed in the Manager of peripheral devices (printers and imaging devices), I removed the Windows 10 print queue and I deleted all the data of the folder under the Program Files (x 86) HP folder on my hard drive. I also disabled Windows Defender and run the installer as administrator, yet none of these steps help the process at all. I have never, in my 20 + years using nothing other than printers HP, encountered a problem like this. I'm used to receive error messages during the installation of software to fail, but I have never had a process simply disappear from the computer without leaving any trace of never having run. I hope that someone out there has an idea, that I have not thought yet, transferring files to my tablet to print from becomes a pain in the rear.

  A man who took the freedom of another man is a prisoner of hatred, he is locked behind bars of prejudices and narrow-mindedness. I am not truly free if I take freedom away from someone else, as surely as I am not free when my freedom is taken from me. The oppressed and the oppressor similar are stripped of their humanity.
  ~ Nelson Mandela

  Welcome to the HP Forums @GarfieldFan1969,

  I understand the printing software will not fully installed for your Photosmart C309 on your system Windows 10, and I wanted to answer with my suggestions for trying to help! Here are my suggestions for you to try. When you are finished, please let me know the results and problems or errors that you may encounter!

  First step: clean boot, restart the PC and try the install again.

  1. start by typing "msconfig" in the search box of Cortana, and then click MSConfig (run command)
  On your keyboard press Windows + R key at same time and type Msconfig in the run window, and then click OK or press ENTER.

  2. now, choose Selective startup

  3. Remove the check of the Load Startup items

  4. click on the Services tab

  5. check "hide all Microsoft Services" and then click on disable all

  6. click apply , then OK

  7 restart the PC and temporarily disable firewalls or antivirus programs

  8 run the Installation Wizard for Windows HP printer to install the printer

  9 turn on the firewall and start services

  Second step: you unregister and re-register the Windows Installer Service:

  1. hold down the Windows key + R to fill the box "Run" and type cmd.exe, and then click OK.
  2. at the command prompt, type msiexec /Unregister , and then press ENTER.
  3. at the command prompt, type msiexec/regserver, and then press ENTER.
  4. at the command prompt, type exit and press ENTER to close the command prompt.
  5. run the Wizard for Windows HP printer installation

  Step 3: run System File Checker Scan (up to 3 times) to repair the corrupted system files:
  1. go to start
  2. type CMD
  3 right-click and run as administrator
  4. to check and repair the OS type sfc/scannow (note the space between sfc and ' / ')

  You may need to run this upward to 3 times to solve all the problems

  When finished, it will say one of three things
  Windows did not find any breach of integrity (a good thing)
  Windows resource protection found corrupt files and repair the (good)
  Windows resource protection found corrupt files but was unable to fix some (or all) of them (not a good thing)

  Try to reinstall the printer.

  Step 4: activate the built-in Windows administrator account

  source

  1. first of all, you'll need to open an administrator mode command prompt by right-clicking and choosing "run as Administrator" (or use the shortcut Ctrl + Shift + Enter in the search box).

  Note that it works the same in all versions of Windows. It just search for cmd and then do a right-click on the icon of the command prompt in the start menu or the boot screen.

  

  2. If you are in Windows 8.x or 10 you can click on the Start button and choose to open a command prompt in this way.

  

  3. now type the following command:

  NET user administrator / Active: Yes

  

  4. you should see a message that the command completed successfully. Log out, and you will now see the administrator as a choice account.

  (Note that this screenshot is for Vista, but it works on Windows 7 and Windows 8 and Windows 10)

  

  You will notice that there is no password for this account, so if you want to leave it enabled, you must change the password.

  Try to reinstall the printer.

  

  Testify of my answer by hitting the thumbs to the top slot

  Click on the button "Accept as Solution" if I helped you reach a solution.

• I use trusteer for Bank report but it will not support the beta version firefox o 9, suggestions?

  I use trusteer for banking report, but it will not support the beta version of firefox 9, suggestions

  Trusteer informed me that a new version of their report software that is compatible with Firefox 9 is available at http://download.trusteer.com/Gcur4Wtnu/RapportSetup.exe

• Update for Windows Vista (KB969947) security does not maintain install

  Update for Windows Vista (KB969947) security does not maintain install
  I have tried several times over the past two months installing this update, nothing seems to help scaned pc thinking it as spyware or some other malicious code nothing it just fails and I can't clear it out! any help at all would be great!
  Thanks in advance

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  A (another) Norton or McAfee application has already been installed on this machine (for example, a free trial version which is preinstalled when you bought it)?

  The foregoing despite...

  See the section "How to get help" of http://support.microsoft.com/kb/969947

  For individuals, please visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  Consumer Security Support homepage
  https://consumersecuritysupport.Microsoft.com/

  For more information about how to contact your local Microsoft subsidiary for security update support issues, visit the International Support Web site: http://support.microsoft.com/common/international.aspx

  For enterprise customers, support for security updates is available through your usual support contacts.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft