Out audio CTS 1100 Cisco

Similar Questions

• Select audio device Realtek as the in / out audio device

  Whenever it starts, my ACER laptop displays the following message... «to enable the audio switch function, select the audio device Realtek as the audio in / out device.» At the same time, a box opens upward with three tabs, reading, recording and sound. A device high definition audio is defined as default as usual... I don't understand what he's asking me to set up.  I tried to reinstall the audio driver and the sound works ok, but the rest of this annoying message.  I am running Vista Home Premium with Service Pack 2 installed. Response of the technical service was Acer... Wipe your hard drive and reinstall windows!

  Hello

  Check if your default audio device is set to realtek.

  1. click on start, type Sound in the box to start the search.

  2. click on sound in the results of search at the top of the start menu.

  3. click on the tab reading notice the check mark next to the default device. For most users, the default device is speakers. Make sure that the audio settings are configured as expected. Follow these steps:

  1. on the playback tab, select the playback device, click Properties, click the Advanced tab and make sure that the default Format is set to the value you expect. When you are finished, close this window to return to the previous window.

  2. on the playback tab, select the playback device, click on configure and make sure that the configurations are set correctly.
  If the sound settings are well positioned, you are using speakers as the audio device and your speakers are already set as the default device, go to method 5 now.

  4. If it is set to realtek change for speakers as the default audio device and then click on set as default.

  5. click OK to save your settings and close the sound dialog box.

  Once done with the above step restart your computer and check if you experience the same problem.

  Let us know if that helps.

  Kind regards
  Anthony
  Microsoft technical support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• External Audio calls to Cisco MCU

  I have a requirement for an external audio channel to access the shared meeting room that is hosted on the MCU 5320 Cisco.

  This can be achieved directly through the MCU or is it a requirment for another audio bridge

  Well, you can integrated MCU with VCS using SIP Trunk, even if the common deployment is to have registered in VCS, MCU or by using SIP, H323, or both. You can also integrate the MCU with CUCM, but in this case, MCU will be a multimedia resource of CUCM, thats why it is only recommended to the ad hoc conferences. You can also integrate the MCU with the driver of telepresence using the API, but it is often only when you have several MCU pools to manage.

  To integrate the Cisco MCU with VCS, you can consult this document:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/MCU/Install_Guide/Cisco_TelePresence_MCU_Deployment_guide_1-31.PDF

  To learn more about how to work with auxiliary self on Cisco MCU, take a look at this guide:

  Page 88 - http://www.cisco.com/en/US/docs/telepresence/infrastructure/mcu/admin_guide/Cisco_Telepresence_MCU_5300_Series_4-4_Product_administration_guide.pdf

  If you want to integrate MCU with control systems third call, I can't say that it will work, because I still have my suggestions on basis Cisco official documentation, and there is little in the literature on integration of MCU with control systems third call.

  If you think that your question has been resolved, please mark the right answer.  =)

  Concerning

  Paulo Souza

  Please note the answers and mark it as "answered" as appropriate.

• Video editing in Photoshop - unsatisfied desires (waveform in the drawing tour - mitigation, ease-out - audio)

  Hello, I edit videos in Photoshop CC (available first, but no option, see below). I edit screencasts in numbers almost industrial, and while in the aspects most Photoshop CC seems more useful than the first my specific needs, there are a few things that I sorely lacking:

  • Audio track should show the waveform
  • Mitigation, ease-out for dynamic expansion or objects in motion (as opposed to the strictly linear change)
  • To show a contour round or square drawn as if by a pencil on paper

  Is - this somehow availabe/feasible in video editing Photoshop CC? I am aware that this wish list is answered by creation, but I use it for other reasons.

  These features mentioned above should be availabe in Photoshop for the creative cloud subscribers who subscribe to the entire suite (not only Photoshop/Lightroom)?

  PS.

  And I'm not going to use first, please accept. In fact, I used Camtasia video editor about 10 months, which was very nice for screencasts and addressed to all my points above. But in Camtasia, upscale footage seemed blurred, while Photoshop pixel replication value creates much better enlargements of dishes GUIs.

  Hi and thanks for joining in.

  We are fundamentally user-volunteers and our staff offering technical and even technical support for Photoshop, but we don't make decisions on what is programmed.

  To make known your wishes, go here: Photoshop community customer family

  Also have you considered first? It's not cloud as Pro, you own it outright. It can have only the features you need.

  Gene

• HP Pavillion DV6: Updaing for Windows 10 knocks out audio Beats

  Upgrade to Windows 10 and said goodbye to my audio. (souds like mutilated)  Had to reinstall widows 7 and all is well again.  How can I upgrade to Windows 10 and work around this audio problem?

  Hello:

  Because HP does not support your laptop for W10, the only suggestion I can offer is to try this IDT HD audio driver after upgrading.

  This package contains the driver that allows to the Audio IDTHigh-definition (HD) in models of laptops that arerunning an operating system supported.

  File name: sp63555.exe

  He worked for laptops for some people, 6xxx/7xxx-dv6 and dv7-6xxx/7xxx.

  If yours is older than the document (dv6-2xxx/3xxx/4xxx/5xxx), I don't know if this driver has a chance of working.

• HP Envy 17: No HDMI out Audio Option on laptop, brand new HP Envy 17

  I'm watching youtube and other video streaming on my TV. I have a receiver that has 5 hdmi that I use to run my appliances. When I plug my cable HDMI video playback on my tv but not audio, and I hear the external device disconnect sound. I opened the Device Manager and see a mistake above Hi Definition audo device under sound. I am very frustrated trying to diagnose this. HP support has updated the bios and searched, and pretty much shrugged and said we do not know. I've updated the audio driver and no chance here. On my 8 year old laptop, wives, all you do is right click on the white speaker and select an hdmi output.

  Cliffs:

  Plug HDMI laptop brand new, video plays on TV no sound, tried installing new drivers and updated CV updated the bios and still no luck.

  No option to HDMI in the playback devices

  I tried 5 different cords

  Cannot start the error above Hi Def Audio Device under Device Manager Code 10 device

  Replacing the motherboard seems to be the best resolution if the HDMI port has indeed.  I suggest to use the warranty. I ask that your question is raised.

• Re-routing Audio out audio in

  Hi guys, I was wondering if the card its Conexant has the ability to natively route the audio signal audio signal without third-party software. I'm having a hard time finding this info. Thanks in advance.

  No, it isn't.

• Remove Fade Out audio and video.

  Is there a way to remove a fade on or melted in the dark of an already edited clip? The audio must be possible, but perhaps not in video.

  Do you mean 'edition' or 'exported '.

  If the latter... no way.

  If the former... Yes, if you are in the project file or the original source files.

• How can I fade in and out audio only below a certain frequency?

  I have a MP3 from a MIDI file in which all instruments are unfortunately in a single track. I want to fade the part of tom because I thought it would be easy to consider his obvious separation on the part of marimba in the Spectral of Pitch display. How can I fade in these lower sounds only without affecting the sound of the marimba higher?

  You could choose from 200 Hz to 0Hz with the marquee tool in the exposed spectral frequency display, then apply a Fade effect.  You can also use the frequency Splitter tool to separate the file at 200 Hz, slide both in multitrack to separate tracks and use controls melted or an envelope to adjust the levels of each spectrum and bland.

• Additional microphones for 1100 CTS

  Hello

  Do you know how many additional Microphones can support a CTS 1100?

  Hi Omar,.

  The phone profile for the STC-1100 in CUCM will support 1 or 2.  The second microphone is connected to the port AEB Center mic 3 (green port 3).

  Of the Installation Guide:

  Optionally, you can install the second microphone on the opposite side of the table to ensure the coverage of entire table of audio conferences only microphone. If you install the second microphone, install it 18 inches (46 cm) from the edge of the table which is closest to the 1100 CTS.

  http://www.Cisco.com/c/en/us/TD/docs/Telepresence/cts_1100/cts_1100_asse...

  In this case, the second microphone would serve only to Audio conferences.

  -Jonathan

• XBR65X800B digital audio out not working not

  Today, I received my new XBR65X800B and everything works fine. Except that when I want to use native applications, the audio output does not work. I can get audio through the TV speakers, but I want the audio to come through my bar of his home theater rather (Yamaha). The red/white audio cables come out of the OUTPUT port on the back of the TV and in the ports on the home theater and it is set to TV mode for entry. All my other devices are plugged into the home theater with HDMI and HDMI output that goes to the TV to carry their signals to it there. I tried changing the Audio settings to the Audio System and the headphone / Audio Out audio as well. I tried out digital and mono ports at the back of the TV.

  What else can I try to get this working?

  Instead, I bought an optical audio cable and that fixes the problem.

• Error 500 CTS Cisco ' remote site is not supported contact your technical support.

  Hi guys, I installed 2 Cisco 500 CTS with Cisco CM 7.1.3

  I've updated the CTS 500 version 1.6.7 and I could add to the Director and I have followed all the configuration mentioned in Configuration Cisco Telepresence with Call Manager.

  I also configured the Midlet services and everything seems to work very well.

  The problem is when I'm doing a call between the 2,500 CTS, I'm getting on the screen the below error:

  "Remote site is not supported contact your technical support.

  Knowing that the two CTS have the same version and two of them are registered correctly and no problem is show.

  Can someone help me how I can check where I get this error?

  Thank you

  Seems to be a problem of config CUCM

  Check box and the location make sure you allow enough for a video telepresence call P.C.

• DVI-HDMI with AUDIO

  I am trying to connect my new Pavilion p7-1240 to my HDTV but do not have a HDMI port on my new computer. After doing some research I'm to mix signals about whether or not a DVI to HDMI cable will carry audio. I just called Radio Shack and they are salesman told me that the AVIO HDMI to DVI cable carries the audio. However further research says that it is not.

  I would appreciate another opinion if you please. Bewilderment of a seller a week is enough. Thank you!

  Hello

  1. the standard DVI carries only video, standard HDMI carries both video and audio.
  2. DVI to HDMI converter adapter / (no need to convert) carries video only.
  3. you need a cable to carry the audio from your laptop to your TV. They can sell a combined adapter, but it must get out of the 2 ports on your laptop: DVI port for video and headphones or line out audio port.

  Kind regards.

• Audio dropouts on Satellite P100

  I have a Toshiba laptop Satellite P100 PSPADE.
  OS: Win XP Professional
  Connected equipment: MOTU 828MKII Firewire or Terratec DMX 6Fire USB.
  In both situations, audio dropouts occur, using Cubase SX3.
  I already disabled some elements in the Manager of hardware devices, such as:
  -Microsoft AC adapter
  -Control compliant ACPI Microsoft method battery
  -Network adapters
  -Bluetooth device
  -Sound controller
  - ...
  Only the devices battery generated many audio dropouts, which are now reduced by disabeling the drivers.
  Nevertheless, sporadic abandonment occur always.
  Although, Terratec, and MOTU audio devices using the maximum buffersize, increasing latency, but reducing the school drop-outs, audio drop outs occur.
  Reading a few articles, I came to the feature 'gas CPU"of the Toshiba laptops, which might be responsible for these audio dropouts.
  The articles mention that he is a non-configurable feature of Toshiba.
  Audio dropouts seem to occure synchronous with the activation of the fan.
  To contol the latency, I use "DPC latency Check" program, which generates a bar graph.
  The peaks of bar-graph each time that the fan turns on and at the same time, a stall audio is heard.
  Is there a solution to the problem of audio dropout?

  Erik

  Hello

  There were MANY discussions on this subject, especially with your machine. Many users tried different solutions such as remove things from the device manager like you did already.

  In General, editing music with a laptop are not really optimal. For example:

  I have a computer of office machine with a Pentium 4 2.8/1 GB RAM/WD Raptor/ESI Juli @ and I also work with Cubase SX3. There is NO problem with the latency (latency DPC latencies around 15-30 microsec Watch).

  I tried to make some changes on my Tecra A9 which has a Dual-Core, 2 GB of RAM, a HARD drive with 7200 RPM with XP on it, etc... and at the beginning I had many heavy withdrawals.

  But after a search of this forum and a few other sites, Ive created a small tutorial:

  1. services:

  For Windows XP: Please visit the following site: http://www.blackviper.com/WinXP/winxp.htm
  and apply the configuration of services twisted.

  For Vista: Go to this site-> http://www.blackviper.com/WinVista/Services/ and see the following:
  -Configurations of Viper black Windows Vista SP1 Service-> twisted
  -Super Tweaks

  -In addition the client must disbale the service "smart card"!

  2 disable the following devices:

  -Compatible control method battery ACPI Microsoft
  -Intel ICH8M Ultra ATA Storage Controllers (including the optical disc drive)
  -Ethernet and Wifi
  -Storage-> Microsoft iSCSI initiator controllers
  SD card controller

  3 disable the powermanagement features:

  -In 'Device Manager' option to allow the computer to turn off this
  all "USB root hubs" should be unchecked
  -Create a separate powerplan who can be named 'Maximum' and put EVERYTHING
  maximum (disable these features like 'sleep' and 'sleep')

  4. run the application 'msconfig' (internal tool of windows) and remove all the
  unneded services and applications in the startup list, which could include
  some tools Toshiba as "configfree" "flashcards" etc., but at YOUR OWN RISK!

  5. as you have more network connections, you can also disable all
  services such as "Windows Defender", "Windows Firewall", "security policies."
  etc. which contains a large number of resources!

  6. I recommend to keep all the drivers including BIOS update. You can use
  drivers of Intel on the chipset/storage controller/graphic chipset
  which most are more recent so our pilots.

  -> Below only for Vista!
  7. at least, you must disable this thing together graphic Vista as
  «Aero, "Windows Sidebar", etc., and switch to the Vista Basic theme.» The window
  Manager themes Vista is necessary and a LOT of resources that offers more
  resources for applications and results also in a latency time reduced.

  8. check the Web site of the manufacturers on the updates support for the device that is in use! (which means the sound card ;))

  It could be that useful...

  Welcome them

• Satellite M100: TV card realtek HD audio problem with Ulead DVD movie factory

  Hello!

  I just bought a new TV tuner card. All works find on my other computer laptop xp (not toshiba) for my toshiba m100, all are ok except for the audio.

  I used a lot of tv as honestech TVR 2.0, Intervideo windvr software 3, HT TV Plus gold but none can deliever the sound.

  Then I stumbled on Ulead DVD movie factory software that is packaged with my Vista Home Basic when I bought my laptop.

  I looked at the advanced video capture option, but there is no audio input source. It makes me wonder, if the supplied software, given my toshiba itself cannot solve this problem, it is must be something wrong here. Page here [http://img132.imageshack.us/img132/9449/tvge3.jpg | http://img132.imageshack.us/img132/9449/tvge3.jpg]

  My toshiba m100 uses realtek high definition audio.

  How anyone has here the idea out audio?

  Sorry, but I don t understand what you want to do.
  If you want to capture the sound, you will need to connect the audio device to the audio line in port. BUT the laptop does not support such port!

  I presume that you have plugged into the external TV tuner card. Well, in this case, you should check the properties of the TV tuner!

  By the way; the laptop supports the sound chip of the HD Audio Realtek ALC 861.
  Visit the Realtek site and download and install the latest driver from the page!