P1102W laser loses connectivity to each power down

Similar Questions

• ENVY 17 t-J100 Leap Motion: keyboard backlit ENVY 17 t-J100 Leap Motion edition shuts down after each power down.

  My brother has an ENVY 17 t-J000 Quad Edition. Only about 6 months. Its backlit keyboard remembers its state of on or off when it reboots or off. When he turns on his laptop back, the keyboard is always if it's him on when he turned off the laptop.

  I just got the ENVY 17 t-J100 Leap Motion backilt keyboard edition. But every time that I reboot or shutdown with the backlight on, it is turned off when I have the laptop or reset. So whenever I have to re - turn on the backlight. Very annoying.

  Anyone else with the jump movement 17 t-J100 having this problem? If so, I hope it's fixed soon. I also can't update the Nvidia drivers then perhaps we need a BIOS update to solve these two problems.

  I just checked to be sure. It turns off if the laptop is turned off and turned on then again - but if I just restart the kbd is running.

• My PC loses connection local and Internet after waking from sleep/hybernation.

  My PC loses connection local and Internet after wakes up from sleep/hybernation. The problem is solved by resetting the network card, but it is frustrating to have repeated resets every time the system in place to wake up. I am looking for a patch, I searched all the support sites and forums where there are similar problems that have been offered to different patches over time, but each of them has failed.

  Vista 64 SP2

  Hello

  Check the updated drivers for the NETWORK card and WiFi.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat above for network card (NIC) and is a good time to get the other updated drivers Vista
  love the updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Also, check the power supply for the device management settings in device - double click Manager
  the device and the power management tab.

  ==============================================

  More if necessary:

  Check your settings (BIOS/CMOS) - usually F2 as you start - Wake on Lan, Wake on Modem and so on.

  Troubleshooting Windows Vista sleep and extended
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  May need to reset all to default power settings and then place back as you prefer.

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  May need to reset all to default power settings and then place back as you prefer.

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Desktop Pavilion slimline s5623w installation of card firewire but how to connect to a power source?

  First of all, I HATE THE SLIMLINE MODELS. NOT WORTH THE MONEY! got as a gift and thought, I could replace 2000 mine thinking it was cheaper because the technology is less expensive.  BIG MISTAKE!  sucks it first audio, so I had to buy branch pregnant even hear, I use the old speakers from my other computer to my mp3 player and it rocks!  then I find not modem phone fax so I buy a usb phone modem, but wishes to make all kinds of mistakes.  now I have these old camcorder videos I want to run through this program a and discovered the firewire card was too big and did not yet align.  on my fourth product now and this one fits.  Yes! but now, we must be connected to a power supply inside the computer? where is he? has a white connector with pins on it but no wires and where is the food, which is not connected to anything else?  Need help please, cannot afford to buy a new computer and it comes to the central computer of my house.  I know a lot of things apart and do their work, but these slimlines suck.  now I know why, they are thin because they have emptied the thing.  computer first for a school kid, but not someone who keeps her home running with everything I do.  So where to connect?  How can I get this thing to work, because it fits so well after all this time looking for the right hardware?  the only reason for which I installed today was because a disc is stuck in it, because the disc is made to be vertical, another error!  disks grind and get lost in there... but I would like a response to my concern at the moment... can not replace the thing and did not have my only other more... Thank you double checked okay there a power connector to the white thing with pins but to connect and what wire?

  To Associate Dean wb2001

  The firewire card is fine as I had mentioned previously.  I installed it and the computer knows it's there.  I really don't see why the name of the thing is so important.  I DON'T PLAN to buy anything else for the problem I have, and I never told him I would.  The only question was if the thing needed food and where to find it, but on mine, I found some answers to that too if I have to use this way.

  so I have thought my problem already and the card firewire is fine.

  That's just the problem with the software now.  I was going to change the thing to the other pci slot and see if anyone makes a difference, but the computer has recognized the new hardware.  This isn't something to do with the firewire card or computer.

  As your couriosity is so bad, Dean associated wb2001,

  I had bought the firewire from newegg like this card and found the profile down those who have the extra bracker for proper size.  It is manufactured by Rosewill.  went with no problem, really easy.  but these slimlines haven't ligned up very well the other slot PCI express.

  It may just be the old camcorder... What is needed right now is the driver for the thing.  an trv520 sony handycam dcr.  I don't know if there is a driver, but when you look at I found one, but still does not recognize the camcorder.  then, in windows, they said all the drivers are included in the operating system for these things, but do not automatically install it like any other.  I'll most likely find the answer by myself around the research on this topic, or I could receive a fair he made on discs, since I only have a few strips of film, but was hoping to get to again use this camcorder.  so I'll see.

  Then Associate Dean wb2001

  I don't even understand your statement!  mix you some point of what the devil, is a lottery?  MY BEHAVIOR WILL NEVER HAPPEN!  I'm still learning what I find, I just took part an out Alienware desktop computer while he was blue screening and crashing on my son, now it works like new!

  You didn't not give me a solution, I found it myself and an attitude you squirt!  I wouldn't be here to help other people with the same problems I am and if I found the answer, I would not share expected points and giving a few statements of nose snot... For the record I WAS NOT LEAPING TO BUY ANYTHING!

  I GIVE YOU THE THUMBS DOWN!   Associate Dean wb2001

  I'm not a stupid kid, I had worked with one of the first concepts of a desktop hp back in the early 80s shipped directly from California.  has shown the President of the company about what I could do with the software that has accompanied, that was enough to make them one of the first companies to use the registers of retail computer that we see now and abandon the old IBM.   Although these dinasaurs are always being used LOL.

  so I don't deserve your forest to a condescending attitude!

• Satellite M30X-129 loses connectivity with the external USB device

  I have a problem with my laptop that has regularly been do worse and I can handle is no longer!

  Whenever I work with external devices via USB ports (all kinds of devices but my external hard drive Smartdisk CrossFire and my iPod in particular), after a certain period of time (sometimes minutes, sometimes hours) the laptop loses connectivity with the device.

  If happens to be listening to the music, download photos from a camera or laptop computer for the ' net or sync of the iPod, the connection is cut off, turning off the device and I have to start all over again!

  I'm almost at the point of launch of the laptop by the window, so any help is most welcome.
  Thank you
  Abderrahman

  Hello

  This happens also with the external USB mouse?
  This occurs if the power adapter is plugged or only if the laptop running on battery?

  In-hubs properties > Device Manager USB root-> power management
  You will find the option called allow the computer to turn off this device to save power.

  I would recommend the brand and disable this option.

  Maybe it helps.

  By the way; When do you update the operating system? I think that it s there long time, perhaps some system files or registry entries are corrupted or a 3rd party application affect the USB functionality?

• Photosmart HP 7520: All wireless network devices will lose connectivity after printing

  Dear all, 
  
      I have a problem with my HP Photosmart 7520 printer where all wireless network devices will lose connectivity after a printer has been sent to the printer.
  
  * Summary
  Wireless network unusable after sending one print to HP printer
  No device ( computers nor smartphones ) can use the Internet nor access internal networks ( 192.168.0/24)
  
  * Details
  Turn HP printer on.  ( wireless direct is off - never turned on )
  HP printer connects to working wireless network.
  Other devices ( phone/computers ) already connected and working.
  From any device, send a document to the printer.
  Printer prints document successfully.
  Immediately after printer has printed all devices cannot access internet IP range ( including HP printer ) nor Internet nor router ( 198.168.0.1 ).
  
  * Reproducibility
  Always
  
  * Work around
  Disconnect all devices from the network.
  Power off printer.
  Reboot Internet router.
  
  * Attempted solutions
  Removed wireless configuration.
  Factory reset.
  Added wireless configuration back.
  Powered on and off printer.
  
  * Printing tested with
  Tested with Macbook10.11/Windows 8/Ubuntu 12/Android 4.4.2
  
  * Not tested
  Ethernet cable directly connected to router.
  
  * Internet Router
  Netgear CG 3700
  

  Number of brand and model of the router?

  These settings are to set up your printer wireless (or wired):

  • Stay connected to your router
  • Trouble printer status 'offline '.
  • Wake mode 'sleep'
  • All wireless devices stay better connected

  While the DHCP is convenient, devices like printers (wired and wireless) should always be assigned a (fixed) IP address manually to avoid conflicts on your wireless network and must be outside the range of the router DHCP.  After the adjustment of the static IP address the computer must be updated to show a Standard TCP/IP port with the IP address of printers under printer properties/Ports.

  1. Set a static in the printer IP address (click here) outside the range of the DHCP of the router (check your manual). It is for Linksys routers, but can be used for all routers. Check your DHCP range and change this first if necessary. More Help Wireless Printing is here and here and still more here.  Video here explains the problem and how to solve the problem. <--> So watch this!
  2. Or check in the printer "Auto Off/sleep/Energy Saving Mode" is disabled the System Mode Time Out is set to zero (0) Use the built-in webserver (EWS) by visiting the printer address IP address in the address bar of your browser, click on settings tab/Auto Off. Or use the printer, printer Home Page (EWS) Wizard. Also check your printer properties.
  3. If the printer supports and has IPv6 enabled, disable the IPv6 option in the printer.
  4. Make sure that the printer is connected directly to a socket wall and not to a UPS, power strip or a lightning arrestor. This will cause the printer to drop offline connection and disconnection (checked yes!).

  Additional measures to take if you continue to have the problem (if they are posted)...

• OfficeJet Pro 8600 all-in-One connected as network printer loses connection

  In December 2011, I bought a HP Officejet Pro 8600 all-in-One to replace an Officejet 6500 as my network printer home. The 6500 worked very well on my cable, but his screen did not, I tried some of the features offered by the 8600 and I got a good price on a new warehouse of BJ. I have the 8600 connected via ethernet (not wireless), with a static IP address. All my computers on the network are running Windows XP Pro SP3 and are up-to-date with Microsoft updates. However, from one day to the next my 8600 will lose connectivity scan (Scan of the computer shows it as being disabled on all my computers at the same time, and I can't reconnect), and if I do not have anything he'll (as in a few hours) also lose connectivity impression. The only way to restore connectivity is to uninstall the HP Officejet Pro 8600 device software basis of all computers, and then reinstall the printer. I had a phone conversation and two debates with HP Technical Support; They suggested that the problem is in the firewall on the computers (but if that were the case I don't think that the loss of connectivity would occur on all computers at the same time), the IP address setting (doesn't make sense) and the printer driver is not not the latest version. I tried all the suggestions, and none of them have solved the problem. The last counselor "has raised the issue to the next level", which proved to be a Manager with no technical expertise and his only suggestion was that I have to return the printer to the merchant. I think the problem is the firmware in the printer (which, according to the 'update' on the printer option, is the latest version). Any other suggestions or experience?

  After a lot of research and find the settings that I did not know that Windows XP offered, I found that the following appear to have solved the problem I've known - at least the printer is now operational for more than 48 hours without losing printing or scan connection. Here are the steps I used:

  1. Start Control Panel  connections network and Internet

  2. Choose "network connections."

  3. Right click on "connect to the Local network.

  4. Choose "Properties".

  5. In the top window is the name of the Ethernet computer connection port, select "Configure" next to this window

  6. Select the tab labeled 'Power Management'

  7. Uncheck the box "allow the computer to turn off this device to save power".

  8. Select the "Advanced" tab

  9. Select the entry "power saving Mode".

  10. If this entry is set to change 'On' to 'Off '.

  11. Select 'OK', and then close the windows that were opened

• WRT54gl loses connection only on line channel

  Hello

  I met the wierdest problem.

  My PC loses the connection with my WRT54GL router and in this case the only thing that brings the back of connection is made power cord from the router and then by him plugging.

  When the PC loses connectivity to the router all other computers in the House connected by a wireless connection stay tuned! Only the PC connected by LINE loses connectivity. Restart the modem or PC does not help. Even clicking on the RESET button of the router does not help.

  I am running Windows XP, the router is set to STAY ALIVE, I can connect to the router admin and see the IP but can not use the internet.

  Does anyone have any idea why this happens?

  Thank you

  O.

  On your computer, turn off the firewall and Antivirus and then check if you are able to go online or not. If still no then on your computer, open the command prompt window and type 'ping 208.67.222.222' and press on enter and check whether you have found all the answers, if so, you can assign a static DNS address for your computer.

  On your, click Start - Control Panel - network - computer connection, right click on wireless network connection and click Properties and then select "TCP/IP Internet Protocol" and click on properties and below to select the option "use the following syntax address DNS server" and in favorite type of DNS: 208.67.222.222 and auxiliary DNS: 208.67.220.220 and click OK...

  Once done, you can restart your computer and check if you are online.

• LaserJet P1102W: [RESOLVED] LaserJet P1102W does not connect to a wireless network on Mac

  UPDATE: the below solution worked on my MacBook, both running El Capitan. Ignore the instructions provided in the manual of the P1102W and follow the steps below.

  I have a P1102W printer.

  Recently my LaserJet P1102W refuses to connect to networks using WPA Wireless.

  As it does not have an IP address, I can't access the web server.

  She also does not connect to my Mac Wireless via Bonjour. The printer will install when connected via USB.

  I installed printer HP Apple drivers, that contains the P1100 driver.

  The P1102W worked before wireless. I only noticed this anomaly since installation El Capitan and moving the printer to another room with my workstation.

  I need the printer to use the wireless network, as I did not have enough space on my desk for him. And I just can't place it anywhere within the range of a USB cable.

  Are there alternatives to this?

  Hi @rcosgrove,

  Welcome to the Forums of HP Support!

  I see that you encounter some problems connecting your Laserjet P1102w printer to your network wireless using your Mac computer. I can help you with that.

  First of all, I would like to mention that it would be easier to the printer connected to your network using a Windows PC. If you can't borrow or use a Windows PC, the following steps should allow you to connect the printer. If you can borrow a PC, please let me know what version of Windows and I can provide a link to the drivers to configure the printer automatically.

  Preparation of the printer

  1. Turn the printer off.
  2. While the printer is turned off, hold down the two buttons on top of the printer.
  3. Hold the buttons on top of the printer and the printer.
  4. Hold down the maintained for even 10 seconds.

  Wireless printer setting

  1. Make sure that the printer is connected to your Mac via the USB cable.
  2. Click on your Apple icon, system preferences and printers and Scanners.
  3. Click the icon of your printer on the left.
  4. Click Open print queue, printer installation, utility of printer, open printer and HTML Config utility.
  5. (If the above step generates an error, change your default browser on Safari. Please let me know if you need assistance with that).
  6. In this new window, click on the networking and wireless tab on the left.
  7. Under Mode of Communication, select Infrastructure.
  8. Select your network from the list and then click on the button with the arrows.
  9. Under Security Mode, select WPA/WPA 2. If you have an old router, you may need to select WEP instead.
  10. Enter your password wireless in the field below.
  11. Click on apply.

  Now, wait a few minutes. Your printer must change to have a solid blue light. If it is not the case, either the password has been entered incorrectly or there is a setting on the router that the printer is having a resolution of the issue. Please let me know if this is the case.

  Once you have a solid blue light:

  1. Unplug the USB cable.
  2. Return to the printers and Scanners.
  3. Hold down the CTRL key and click the icon of the printer on the left.
  4. Click on reset printing system.
  5. Click on the button "+" in the lower left corner.
  6. In this window, select your printer in the list.
  7. Click in the box next to and select your printer from the list.
  8. Click on Add.

  Please let me know if you are able of print or the results after following the above. If you can print, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope this information is useful. Please reply to this message with the results. Good luck!

• printer wireless 3050 j611 guard lose connection

  My printer wireless-3050 j611 guard a lose connection. Sometimes the Internet work to a crawl when this happens. I have run all kinds of utilities, virus checkers, re - install printer DCP. When he gets back online, the Internet seems to run at full speed. It's embarrassing. I am connected via ATT Uverse.

  Hello hollywodBDA

  I work on the assumption that you are running Windows 7 that you have not specified a operating system that you are running. I will give you is a called HP support document: troubleshooting your wireless network and Internet access (Windows 7). If you are not running Windows 7 just Google search "Troubleshooting your wireless network connection" and Internet and pick the one with your operating system. Now, this document should help you identify what is happening on this is the cause of your network to go down. It is not a coincidence that you lose the connection to your printer when your network goes down that it communicates on the network. Think of it as a phone line, you talk to someone to say New York, and the telephone system breaks down. It is not a problem with the person you're talking to New York, but the network which has cut off the communication.

  Now, this does not mean that a printer can't get a network, it is just unlikely. I would consider the most obvious causes such as computers on the network and even the router itself.

  If you want to identify which device is take them down to remove network devices one at a time until the problem stops and/or Exchange on to see which is causing the problem.

  I hope that this will lead you to the solution on what take down your network. Thanks for posting this topic on the Forums of HP feel free to re-post if you still need help. Have a nice day

• Message "do not power down during the update"control panel screen not fade.

  Product name: HP ENVY 100 e - All - in - One Printer D410a

  Product no.: CN517A

  The message "Do not power down during the update" on the control panel of the printer refused to erase and remained perpetually disaloowing acess the Menu home for other actions as photocopies etc.

  I see.  I found this utility that will help you to solve the problem.  It seems the printer lost connectivity during an update firmware and glitch out.  The utility should take care of it.  Let me know what happens.

• Power down, windows 7 sets the Verr Num led on just before turning off

  I have a Fujitsu 101/102 PS/2 keyboard connected on a 64-bit windows system 7.

  Recently, my motherboard has failed, and I installed a new motherboard, where I had to do some basic recovery for windows 7 to come.
  Because then I find that when I turned off the system, during the eve of the sequence, when I get the screen power off mode, the indicator (Led) NumLock on the keyboard is turned off first, and then just before that the system turns off the Num Lock Led is lit once again and of course remains on until I then use my PC.
  I would like to get a solution to this problem.

  The State of the Num Lock is determined by the BIOS during POST (Power On Self Test). It is not defined by Microsoft during the power down, but the BIOS of your computer can trigger the light briefly during a stop.

  If you enter the BIOS of your computer during the power upward (F4 maybe?), you should be able to find a framework that governs the State of the NumLock at startup. Change this option to what you want and save your output settings.
  The BIOS settings are retained by EPROM chips on your motherboard, which explains why things have changed with a new motherboard.

• Can someone help me please? I bought Photoshop elements 13 and were not able to install it on my computer.  I made attempts at veveral to install it and I lose connection every time.  Since I was on a package of data plan with at &amp; t, I buy e data

  Can someone help me please? I bought Photoshop elements 13 and were not able to install it on my computer.  I made attempts at veveral to install it and I lose connection every time.  Since I was on a package of data plan with at & t, I have buy the data each month.  I consume ALL my data.  To be a better way. Can someone help me please? I bought Photoshop elements 13 and were not able to install it on my computer.  I made attempts at veveral to install it and I lose connection every time.  Since I was on a package of data plan with at & t, I have buy the data each month.  I consume ALL my data.  To be a better way.

  I am well aware I could you bought the disc version. I bought the software Officemax in Vicksburg, MS I thought that the disc was included in the box.

• VM loses connectivity after a reboot... help!

  I'm lost on this one, I've NEVER seen this problem before.

  The server is an HP DL380 G5 with two 1 GB network adapters. Running ESXi 5.0 (with all updates) one comes from ISP and we're going on the local network (server is mail, NAT and much more).

  After a reboot, the NETWORK card that comes from the ISP, loses connectivity, more often. It will be the Web sites (I guess that's the port open on the firewall) but nothing else. No internet, no. DNS, I can't even ping an external site by its IP. The only thing that works is the Web sites that are currently running. We use this connection for Web sites and Internet for the site so using NAT gives him around our PC, it is important that it works.

  The ONLY way to recover is to remove TWO cards from the network card in Windows and let Windows find their new (drivers). I got this server and copied down to older hardware, and never, it has a problem after a reboot and works with a number. On ESXi 5, even after fixation by the removal of the NETWORK adapter cards, once it gets restarted, I have to start all over again.

  I need to pass to the virtual machine, but so far it has been nothing but a nightmare.

  It is material or ESX that causes this problem, I don't know it's not on Windows server 2003 that they run...

  Any ideas? Please help if you can.

  The problem seems to be what I was suspecting, a routing problem internal VM. I thought you lost the 0.0.0.0 route to the internet, but instead, you actually get an another 0.0.0.0 route that points to the local interface. The route print output:

  Work:

  0.0.0.0          0.0.0.0       < isp="" gateway="">      <   isp ="" ip="">     10

  Does not:

  0.0.0.0          0.0.0.0       < isp="" gateway="">      <   isp ="" ip="">     10

  0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.1 10

  192.168.0.1 is the local IP address of the internal NETWORK adapter in your virtual machine. This means that for some reason, sees itself as the default gateway and also not trying to access the internet through your ISP router.

  If you look at the text notworking ipconfig/all command, you will see that the 'card Ethernet Local Area Connection 4' with the 192.168.0.1 IP itself now has as a default gateway.

  The LAN4 configuration is static, so it's quite strange where the new default gateway information comes. A quick fix after a reboot is likely to open the TCP/IP settings and remove the new default gateway of the interal NIC

  You could also enter a new route persistent to the ISP router with the metric is lower, but I think that we should first try to find out why your Windows 2003 establishes a default gateway on the internal interface.

• If 2 Airport extreme can stay connected to each other using their LAN ports?

  Hello friends,

  I would like to know if 2 Airport extreme or 1 Airport Extreme and Airport Express can stay connected to each other using LAN ports at the ends? I thought this is the LAN port 1 connected to the WAN port on the 2nd.

  Thank you

  To clarify the issue and the scenario, one of my friend described a typical scenario in which there are 2 AEs. AE1 has an ISP in its port WAN and AE2 has a different ISP in its WAN port. This 2 AE can mutually connected between them by using ports LAN AE1 and AE2 ethernet cable? He said this could be feasible if AE2 remained in bridged mode, without using the ISP attached to its WAN port. I just don't get how this is possible. Friends of the search help.

  Thank you