path of the firmware upgrade

Similar Questions

• Problem the firmware upgrade failed WRT54G v8.2

  Today I tried to upgrade my WRT54G Router v8.2 for the latest Linksys firmware. But the upgrade was repeated each time when the progress bar reaches about 75%. It lasted more than 30 minutes and I had stopped the upgrade. Then the router has stopped working. I have reset and hard reset the router. I also tried the method of tftp to upgrade the firmware again. But the problem is still there. When I ping 192.168.1.1, I always get the message "Destination host unreachable". Could someone help me solve this problem? The power and light of the ethernet port light are always on. Is it possible to solve the problem? Any information is appreciated. Thank you very much.

  Do not use the wireless computer to update the firmware. Hard-reset the router for 1 minute and try this link and check if it works...

• After restart of the firmware upgrade

  Hi, I need to update the firmware on my controllers PS6100 EqualLogic.

  I found the instructions on how to do it and everything seems straight forward to do so via the GUI.

  I noticed there is a necessary restart after the firmware has been applied. Does this mean I have to gracefully shutdown the virtual machines running on my SAN LUNS? My iSCSI connections will be closed/broken during the restart of the post firmware upgrade?

  Thank you, Oliver.

  Hello Oliver,.

  In the same area download notes firmware and release is another PDF, entitled ' iSCSI initiator and optimize your SAN environment for high availability operating system considerations ", which includes some key parameters that will allow your computers virtual and servers through the failover time.  It is important that not only the Firmware update, but in the case of an unexpected failure due to a failure of CM.

  More if you use VMware ESXi, there is a best practices PDF for that as well.  In addition to better manage the failover, these changes have shown to improve performance as well.

  The Tech report TR1091 is available here:

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20434601/download

  Changes for Windows and the knots of ESXi virtual machines will require a reboot to take effect.

  What version of firmware you are at, and what version you are migrating towards?

  Other things I always propose updates is to ensure that both controllers are plugged in your switch and in the VLAN correct.  Since assets CM are failed over to the passive, support gets much advertising is unable to access the storage after firmware update.  Or ports of the day before were not in the VLAN correct, or individuals with disabilities, etc...

  It is for these reasons that personally I prefer to do the updates via the serial port CLI.   The process is more talkative, and if something should go wrong, you need the serial port of some sort.   Since the installation and tested in advance is a huge time saver.   Here, we use serial mux so that all array controllers are easily accessible.

  Kind regards

  Don

• UCS C460 M2 - error 1902 during the firmware upgrade

  Hello!

  A few days ago, I could upgrade the firmware 1.5 (7 c) to 1.5(8a) and the BIOS to version 1.5.4a to 1.5.4b using file ucs-c460-huu - 1.5.8 has mapped via KVM using an old windows xp with java 1.7. In fact, this upgrade would allow access of latest java KVM, something that was lost a few months ago.

  On Monday, I did the same procedure on an exact server and everything was fine, but this server cannot update firmware.

  I get error 1902, described here:

  https://Quickview.cloudapps.Cisco.com/QuickView/bug/CSCui18044

  But there is not something to solve this problem.

  Any ideas please?

  Concerning

  David

  David,

  A few steps to try:

  -Turn off the server, remove the power supply and press and hold power for 30 seconds. Retry the upgrade.

  -Restart the MMIC before the upgrade.

  -Try the upgrade using a physical USB vs vMedia

  Let me know what questions you have and please share the results.

  Thank you

  Wes

• How much time it take the firmware upgrade procedure?

  Hello

  I ReadyNas 204 and I'm away from the SIN it free and I wanted to install the 6.5.0 version of the firmware via the admin interface... I'm not sure how much time should I take, it is already underway for 40 minutes... is this normal?

  Sorry for the dummy question!

  Thank you

  Problem is solved. Sent someone back home to check and it seemed that the NAS could not obtain an IP address after you restart. Disconnect the RJ-45 and connected back solved the problem. NAS is back online, but would it be a bug in 6.5.0 or is it just with my camera? Nothing in the newspapers that I could see... just could not obtain an IP address...

  the NAS drive is configured with a static IPv4 address and IPv6 is disabled. If that helps.

• Sony headphones Smart MW1 Pro - the device does not display mp3 information to do the firmware upgrade 0.1.D.0.6

  I bought the Smart Sony headphones Pro because the Sony site where there is an official document indicates that it is 100% compatible with my Samsung Galaxy Nexus.

  Everything was fine, until the unit was asked to update to version 0.1.D.0.6.

  After the pair with the headset Smart Display tells me "No Info" instead of the album and the name of the mp3 information.

  According to the forums, I'm not the only one with the problem and also cannot go back to previous firmware was 0.1.C.0.3.

  My Samsung Galaxy Nexus had the OS: android 4.2.1 when I run right.

  Today the android Smartphone I upgraded to 4.2.2 and maybe thought now and nothing will fix the problem, the problem is definitely the gadget.

  We need an urgent solution to this problem.

  This problem has been resolved by the 0.1.E.1.4 firmware which was released yesterday, also improves the screen, enlarge the icons and the clock digits, also solves problems with the mating with the Vita!

  Thanks Sony Mobile!

• Path of the firmware update

  Upgrades of 6.2.4 directly to 6.4.2 one step or is there a version I should update between the two?

  Yes you can update directly. Disable the antivirus first, if use you it.

• "End of the upgrade of the firmware" required on E1000?

  I recently bought an E1000 router and had to put in place manually (with the help of technical support) b/c the Connect software wasn't working properly with my computer.  Today I called the technical support to ask about upgrading the firmware - for security reasons - I'm not having problems.  They walked me well to download the new firmware updated, navigation on the desktop and install it.  (I have nothing decompress).  I told them I thought I had to do a hard reset 30 seconds or something and reconfigure and I was told this is not necessary.  The site says that all the 4 steps should be performed in order to update the firmware correctly.

  If my browser seems to work correctly afterwards, and the listed version is the new version, should I do the hard reset and reconfiguration?  If I did not, is the firmware upgrade completed?  During the process, we me no what this is pointing upwards, is back.  However, after initially installing the router, I made a backup on mine, just in case.  Not sure it would do any good, however, as he himself has automatically saved as file Outlook for some reason any.

  Thanks for any help!

  If the updated version is indicated on the page of the router and all the devices in the network works fine, then there is no need to reset the router.

• The Linksys BEFSR41 V2 Firmware upgrade help

  I can't open the MacBinary (.bin) files that I downloaded from linksys, in order to update my firmware. I used my utility to archive, Stuffit Expander Mac and BetterZip, and so far none of them opens the file. Anyone have the firmware upgrade in a different format or advice on how to solve my problem.

  Do not touch the file you downloaded. The only software that uses it is your browser.

  You must open the web interface of the router at http://192.168.1.1/ and then use the upgrade of the firmware here.

  I don't know if the demo user interface is always up to date, but if it is as you should find it on the help page. See here. Click Update Firmware. Then, press the Browse button and select the .bin file that you downloaded. Then press upgrade and the browser will download the file on the router.

• BDX4350KB Wifi adapter and firmware upgrade doesn't work do not

  It is a sequel to my earlier question about if the WLM-20U2 Wifi adapter will work in my blu - ray player.

  After buying the adapter I plugged it and a message 'not supported', if I tried to connect wireless it says there was no an adapter connected.

  So I assumed that this necessary upgrade, so I formatted a 1 Gb USB drive with the FAT file system, downloaded the file level (version 39 http://www.dl.toshiba.com/player/NA/GB/EN/BDX4350KB.html) and copied the file .bin on the USB.

  When I plugged into the player and said to check the disk for a file to update it tells me that "frontend file is not found"... There was only one file to download, and it wasn't in a folder so I guess I'm supposed to just copy that file on the USB drive.

  I checked the USB port with a memory stick with photos on and it works fine.

  How to get the upgrade to work in the hope that it will enable the wifi adapter to work?

  Thank you

  Have you checked the guide in PDF firmware update?
  [Update firmware BDX4350KB | http://fget.dl.toshiba.com/manual/install/10009/Installation_Instruction.pdf?fromPid=%2Fplayer%2FN A%2FGB%2FEN%2FBDX4350KB.html&f=Installation_Instru ction.pdf]

  _ * How to upgrade the F/W * _

  (1) update firmware requires the USB of size max.2GB. Please make sure you format the Flash DRIVE to FAT/FAT32 before you start the upgrade procedure.
  ? Create a new folder on the USB drive and name it UPG_ALL
  ? Unzip the firmware file and copy it in the folder UPG_ALL.

  2) turn on the BD? Drive and make sure that you can see the player's on-screen Menu.
  ? Insert the USB key containing the Firmware upgrade file in the USB of the Blu slot? ray player

  3) press the "SETUP" button on the remote control.

  ? Select keys on the remote control UP/DOWN
  ? Symptom
  ? Upgrade
  ? USB storage device

  4) press the OK button on the remote control depending on the USB storage device.
  ? Now the upgrade file is under research. Please wait massage will appear

• 200 d IOmega IX4 Firmware upgrade failure

  Hello

  I have an IX4 - 200 d which I inherited. Initially, it wouldn't boot and display only the symbols of USB stick/network after about 60 seconds.

  With some searching on Google, I created a boot disk USB with the firmware updated on this issue. All goes well until the Firmware upgrade begins. I go to the step of (what I assume is) the upgrade of the firmware and it gets 75%, hold for 5 seconds and then the machine stops.

  I tried to repeat the update of the firmware with all the drives present, with every other drive in the first slot and with all the disconnected drives. But it seems to behave in the same way.

  Is this a known issue? Or could it be a hardware failure?

  I'm pretty eager to find a solution - it takes a long time for me to accept defeat.

  The only other suggestion that suggested Dr. Google is to start linux and reformat the hard drive?

  Any help is appreciated.

  Kind regards

  Pete

  Hi André,.

  This case can be closed.

  After the above mentioned procedure eventually work, I didn't know that - ALL readers should be present and formatted during an attempt of USB firmware update / install.

  The link again on the forum - http://forum.nas-central.org/viewtopic.php?f=14&t=4401

  This seems to be the only solution.

  Kind regards

  Pete

• How update the Firmware on my router?

  I downloaded the firmware file of my router (WRT54GS V7) Linksis wireless because I have problems with the router itself reset while I play, but I can't understand how to install it.  The default program that wants to open the firmware file is VLC (a media player).  What should I do?

  Edit: I'm trying to re - download the file firmware to see if that helps, but now the download links aren't working yet... What is happening here?

  Edit 2: I also try to read the FAQ because it seems that they already have an answer to my question, but the answer page is not loading either.

  The site is under maintenance or something?

  The linksys Web site works fine now. If you still have problems, you must connect the computer directly to the modem for download.

  You should not open the firmware file that upload you to the server. Do not open it with any application. Do not change under any circumstances. All you have to do is to download the file and upload it to the router through the web interface. Download the firmware on the linksys site. Save it to your desktop.

  Then, open a browser and go to http://192.168.1.1/ which is the web interface of the router. The default password is "admin". Search for the function of the firmware upgrade. It's usually somewhere on the Administration tab. On the firmware upgrade page that you see a browse button to select the file to load on the router. Select the downloaded firmware file. Press the upgrade button.

  Do not interrupt the download. It is recommended to disable any firewall or anti-virus while accessing the web interface for the firmware update. The process should not be interrupted. Otherwise you can find yourself with a router of bricks.

• How can I download the firmware for another platform

  Hello. I am trying to download the update of firmware for WRT160N (HW ver3) for a router connected to a XP machine.

  I download a bin file from a Mac and the download page for show me, but I think that's a Mac - I need the (32-bit) version of Windows XP (exe file)?

  Anyone know the direct link to download XP?

  p.s. I can't connect the XP machine to the Internet, it should be uploaded on the Mac.

  Firmware is not executable.  You downloaded the bin file, which is the firmware file.  Access to your administration pages of routers and fine to the firmware upgrade section and follow the instructions, and that it points to the bin file.

• WRT 160NL firmware upgrade ever end!

  Hello

  I am trying to upgrade the firmware version 1.00.01 B15 to 1.00.01 17 (the only one available on the linksys Web site). It is not allowed to turn it off or reset it. However, the upgrade progress stopped at 98% and never ending so far. Should I wait longer (another day)? Or I can just reset/power off of the it?

  Attached is a snapshot of the screen for reference.

  Thank you.

  

  The firmware upgrade process must be complete...

  Try the following steps... Press and hold the button of reset for 60 seconds... Release the reset button and unplug
  the power cable from your router, after only 30 seconds reconnect the power cable...

  Now, as do the settings of the browser on the computer... Open an IE, click Tools > Internet Options, and then delete all files, cookies, history, forms... GoTo 'Connections', make sure never Dial
  a connection is checked, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  Now, try to upgrade your router firmware... it should work!

• WRT610N firmware upgrade question

  I have a simple question about the firmware upgrade.  I want to know if it's OK when the upgrade of the firmware on a wireless router for rather than press reset and rest for 30 seconds, that I connect with my browser and 'load Factory Deaults?

  I read, where they are supposed to do the thing of the SME and the method of web browser is much easier worth me.

  Can anyone confirm this or should I press the button to reset for 30 seconds?

  see you soon

  It is advisable to reset the router after the upgrade of the firmware. For once you upgrade the firmware on the router... Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now, you can re - configure your router.