Pavilion dv6 3111st: L will not start.

Similar Questions

• HP Pavilion dv6-3150us Entertainment Notebook not start after sitting on the side.

  Hello! I have a HP Pavilion dv6-3150us Entertainment Notebook that works under Windows 7. Last week, I traveled with him in Florida, and when I arrived and tried to turn on the laptop, it wouldn't start. The screen was white with thin lines going through it and the screen turned slowly black. I disassembled the computer and put it back together (which I have experience with, I installed a new fan at the beginning of last year) and he came in safe mode. This ihappened still once I put the laptop in my bag on back and then he pulled out a few minutes later (without even moving) and when I got home. I tested the hard drive and memory, and they both passed. Other that this question, the computer has worked fine. I need to get this problem solved, because I am a PhD student and travel frequently with your laptop. Could someone help me please? What causes this problem? Thank you.

  Hey irol72,

  Welcome to the Forums of HP Support! I understand that your HP Pavilion dv6-3150us is not initialize after being on his side, I understand your frustration and I would start you the black screen troubleshooting with no. Error Messages at startup or start-up.

  Thank you

• Pavilion dv6 - 6153cl laptop - will not install the video drivers.

  Recently, a friends Pavillion dv6 - 6153cl laptop started bluescreens frequent (many x 50 on igdpmd64.sys).   (on Win7 64 bit, completely up to date)

  I came across this site and downloaded the current drivers but try as I can, they will not install. The message implies that they are bad drivers, but I have confirmed that they are the 2 parters - driver package AMD, including ATI and Intel drivers for the video "switchable". Most of the AMD install - except the 2 pilots and the C++ package components. AMD checks prior approval from hardware to install and does not renounce it.

  The error is:

  "this computer does not meet the minimum requirements for installing this software.
  or it just keeps trying to install it until it skips this step and goes to the next component, which gives the error the failure at the end.

  I searched this site and found a number of references to similar problems. I've updated the BIOS, all other drivers, removed the old drivers (it is now running on Win VGA drivers), updated part of HP software, run a repair on Windows update and Installer, tried the previous version available, uninstalled C++, cancelled prior unpacking, checked Mode drivers safe, ran HP Support Assistant and tried to manually launch the installation program in compatibility mode admin.

  Windows Update also wanted to update the 2 drivers but who do not. Twice. He will probably try again.

  I ran sfc and Auditor - alls well with the other drivers.

  There is no obvious change that percipitated the question.

  The WinUpdate KB2670838 that sometimes causes a similar error has not been installed.

  The system works at normal temperatures. And it stopped crashing. But only 600 x screen resolution.

  Any suggestions on how to get the drivers to install?

  My friend decided to hold the laptop store as they needed more functional. Of course, they were able to update the video drivers well obviously had a problem with an obscure audio problem. (audio drivers have been included in the package of video driver HP that they perhaps do not use) All is now well and unfortunately I cannot report on what drivers, they used to solve the problem. Thanks for your help, Zak

• HP Pavilion Dv6 win 7 will not connect to the internet (WiFi Atheros AR9258 adapter)

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Hello.

  I have a HP Pavilion Dv6-2110AX Windows 7 Home Premium and one a few days ago I had a problem with the internet/network connection.

  It was working normally and then, suddenly, just collapsed. I tried everything I know: System Restore, update the wireless driver (Atheros AR9258 wireless adapter - ftp://ftp.hp.com/pub/softpaq/sp48001-48500/sp48488.exe), reset the driver (I don't know if I did it right), but nothings helped to y for remedy.

  The only message I get I can't try something there: "Windows has not automatically determine the network proxy settings." I tried to do it manually, but it won't let me change any configuration in there, I don't know why.

  In the Device Manager, it indicates that the wi - fi adapter is not working properly and I can't access internet and network with my smartphone and 2 other computers at home, so I guess that the problem is not the router and I don't know what else to do.

  The only thing I have not tried to change IP address, because I don't have the Setup for this network and I don't know if this will help also.

  I appreciate all help. Thank you!!

  Spoiler (Highlight to read)

   

  Hi.I have a HP Pavilion Dv6-2110AX Windows 7 Home Premium and one a few days ago I had a problem with the internet/network connection. It was working normally and then, suddenly, just collapsed. I tried everything I know: System Restore, update the wireless driver (Atheros AR9258 wireless adapter - ftp://ftp.hp.com/pub/softpaq/sp48001-48500/sp48488.exe), reset the driver (I don't know if I did it right), but nothings helped to y for remedy. The only message I get I can't try something there: "Windows has not automatically determine the network proxy settings." I tried to do it manually, but it won't let me change any configuration in there, I don't know why. In the Device Manager, it indicates that the wi - fi adapter is not working properly and I can't access internet and network with my smartphone and 2 other computers at home, so I guess that the problem is not the router and I don't know what else to do. The only thing I have not tried was change IP address, because I don't have the Setup for this network and I don't know if this will help also. I appreciate all help. Thank you!!    

  MR. B

  Well well, after 1 month trying to get assistance from HP and after 2 weeks in this forum (thanks to everyone who saw the subject and tried to help ) I just gave up and did what I have done since I had the problem.

  My solution was to use the recovery discs to "Reinstall" everything and now the laptop is like when I bought it, but works.

  If you decide to do, REMEMBER to backup all your files before otherwise you goanna lose everything, because the recovery system returns your computer to the factory settings.

  The best thing is, it took less than an hour to do. If I'd known...

  Good luck people, c is the next time (hopefully not soon)... hehhehe!

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Pavilion dv7 3003el: Dv7 will not start

  My dv7 will not today, initialize it power for 2 seconds, then stop...

  Hello @Tomsellek,

  Thanks for the quick response!

  Given that the question seems to be hardware related, you can consider contacting the HP support by phone for additional options.  Please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Kind regards!

• Pavilion DV6-2140ED: Pavilion DV6: 10 Windows does not start after the upgrade memory (4 GB-> 8 GB)

  After I upgraded the RAM in my HP DV6 from 4 GB to 8 GB (2 x 4 GB Kingston KTA-MB1333 / 4G), Windows no longer starts. I get a blue screen and it keeps restarting.

  I think that the memory specifications are similar to the Samsung M471B5673EH1-CH9 original memory: Ghz 1333, non - ecc, 1.5 volts, case latency 9 etc.etc.

  It's a laptop DV6-2140ED HP with a processor Intel i5 - 430 m and Intel mobile chipset HM55.

  The bios detects 8 GB and it also passes the check/test of memory. As far as I know that I have also installed the latest bios firmware: F.1D. Reinstall my Windows 10 64 bit does not work either: with 8 GB I also get blue screens, after I try to boot my Windows 10 bootable USB drive.

  I read other people having the same problem, but I have not read a solution yet. What can we do about it?

  Hello:

  Please see this discussion.  You buy a very specific memory for any HP laptop with Mobile Intel 5 series chipset.

  http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/memory-upgrade-6550b/m-p/5340551/highlight/true#M207994

• my HP pavilion dv5_1110em lap top will not start

  Hi all, I have a HP old wish to computer pavilion dv5 laptop won't start, fan power indicator works on screen on it but empty with just curser dash high on the left, now I got a hard drive on and tried booting into the BIOS, no joy took ram on and I get 3 beeps when I turn on someone can help me more to sort problem much thanks glenn

  Hello

  It could be something to watch at any given time. But probably points to the system of locking up. I'd like to see how it behaves, or if the problem persists, before replacing the battery.

• Pavilion ID46 g6 will not start

  Product: Pavillion g6 ID46

  [Edited by Moderator] Serial No.

  Product # A6Z74UA #ABA

  OP sys: Windows 7 Home Prem OA

  Pavillion G6 my husband will not start. What happened: returned to the computer after being away for a while, shook the wake up the mouse and the screen «has exploded in many colors and motion pixels» Screen went black, then a screen "do you want to start in safe mode" popped up. He tried a start-up without danger, but he failed and gave him a Bios Application error 501. He tried to restart the computer, but it crashes on the 'Starting Windows' screen with 4 color icon.

  I have:

  Removed the battery and tried to restart. Not good.

  Has taken the hard disk and and reinstalled it. Ditto.

  Tried to boot mode safe, before and after the following below. "Loading files" still stuck on Windows\System32\drivers\CLASSPNP. SYS

  Burned and ran a repair disc. Took 4 hours and the program ran at the end when I was asked to reboot. Computer hooked on "Starting Windows" screen. (I left this screen function for more than 5 hours without this change.)

  Ran the program System Repair twice, same results.

  Start of Tests ran. After self-test of the main hard drive, hard drive SMART and verification Test of memory system (passed 100%)

  Tried to restore the BIOS using Windows + B and power with several attempts. Button Power LED stays on, about 20 seconds later a small LED on the "caps lock" key flashes white twice. Black screen and nothing happens after 5 minutes. He raised his eyes and 2 flashes is supposed to be the corruption of the BIOS.

  Error log lists these: quick 03F0 303, 501 error and error of hard disk 1.

  I have a lot of intelligence of the computer, so appreciate any help you can give, especially if assistance is simple and easy to follow terms.

  Mahalo in advance!

  Well, nothing worked and I did not attempt to remove the HD and turn it on again. Husband returned to a comp sci student who managed to get some info on the HD, but said that the HD was shot.

  Good thing is that I got a new Asus laptop and put my old computer to my dear husband. So, I guess that the problem is solved!  Thanks for your help.

• Pavilion a6327uk will not start. Light output at the rear is enabled, all the work of 3 fans, but does not start.

  I have a Pavillion equipped a6327uk for vista 32 bit. I had similar problems before and remove all cables, hold the button to boot without the power connected, reconnect the and then turn on solves the problem. I suffered a blue screen, where I was told the computer was stop and spills of memory. Then I rebooted the computer froze and since then it will not start. I led on the power supply/process button cable about 30 times more than three days without success. The computer does not go to the HP logo screen, it just stops. Can anyone help with further action please.

  It could be almost anything that prevents your computer from starting to start to eliminate things.  If the computer under warranty?  If this is not the case, unplug everything including the power cord from your computer. Unplug the keyboard, monitor, mouse, readers flash and all other connected outside of the machine. Open the unit and unplug all the devices connected to the power supply except the motherboard.  Disconnect the hard drive cable and power supply data connection, disconnect the connection cable and power supply of the CD/DVD data, disconnect any drive card reader or floppy drive.  Therefore remains connected to the power supply should be taking 20/24 pin to the motherboard and 4 or 8 pin 12V for the cpu power cable.  Remove all cards that may be in the slots, as the video card, modem, network card (if they are not built in to edge of devices.) Just the cards that can be inserted into the slots.  Make sure all items are away from the computer and cannot cause a short circuit when you use power. Look at the motherboard and see if the capacitors were bulged or rounded top and maybe even a brown substance leaking from the top.  Check the video card as well for the same and a blocked fan who may have been not turn.  Test the power supply with a volt/ohm meter if you have one. If this is not the case, turn on the power and see if the fans are running and you get beeps.  If this isn't the case, hold the power button for about 5 seconds until the machine turns off.  Try only a chunk of memory at a time and in each of the slots.  If it starts to act normally, it is probably food.  If the sounds seem normal, unplug the power cable and install one at a time from the video card and connect the monitor to it. Plug the power cable from back in and start the machine.  If you have a video, keep disconnect power, adding another device such as the keyboard and the mouse until you arrive finally to your hard drive.  Do your last hard drive because there all your important data on it and you do not want to expose to all this test.

• Laptop will not start without the battery attached

  Hello

  I have a Hp pavilion dv6700 series (dv6840el) and just, it will not start without the battery attached.

  If I plug in the AC adapter, I get some computer activity (fan, noise of the dvd player and HD drive spins) for about 5 seconds, then shuts down.

  Once I plug the battery (which is dying, who need a replacement), the laptop starts fine.

  So my question is: what is a motherboard or a problem with the AC adapter?

  The AC adapter looks ok, however. But if I am considering buying a spare battery, I assure you that I have a new adapter as well.

  Thanks in advance.

  Hello

  Visit this link

  http://h10025.www1.HP.com/ewfrf/WC/documentSubCategory?tmp_rule=61317&tmp_task=solveCategory&CC=US&DLC=en&lang=en&LC=en&Product=5081068&Query=dv7-6052ea&Tool=

  Good Luk

• Pavilion 500: HP500-326na does not start... not the power of USB devices

  Three days of warranty expirition my HP Pavilion 500 turned off and will not start.

  The led on the back of the case is on.

  The led on the motherboard is on.

  Fans for the processor and the case work.

  There is no power to any USB port... so without mouse and keyboard.

  There is no signal on the screen.

  The power switch will not shut the unit, regardless of how long you hold in.

  There is no beeps on the motherboard at startup.

  I cleaned the dust.

  I have disconnected all drives and plugged back in one at a time.

  I deleted the memory chips vivid and re-sitting them.

  I removed the graphics card and re-sitting there.

  All to nothing does not.

  There is no way to run diagnostics or tests with a mouse and a keyboard.

  What else can be done to determine the case of this problem?

  Thank you.

  So if you had followed this document and still has not changed, the only thing left is to contact the helpline.

  Please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

• I can't download Windows updates or updates of Windows Defender, and my BITS will not start.

  Hi, I have a HP Pavilion dv4 Notebook PC, and I can't get my updates of windows to download anything. My BITS will not start.

  -Processor: Intel (r) Core (TM) 2 Duo CPU
  At 2.10 GHz, 2.10 GHz T6500
  -Memory (RAM): 4.00 GB
  -System type: 64-bit operating system
  -Windows Vista Home Premium Edition
  -Service Pack 2

  I have Webroot AntiVirus with Spy Sweeper and I recently downloaded the Malewarebytes Malware Anti.

  Whenever I try to download an update for anything, be it Itunes, Windows Defender, Windows updates, updates to HP or Microsoft Updates, they do not always arrive.

  When I go into the service menu & try to start BITS it comes up with this message:

  Windows cannot start the Service on the Local computer's Background Intelligent Transfer
  Error 126: The specified module is not found.

  When the updates of Windows fails to download updates, it comes up with the error Code: 80246008.

  I tried to download on microsoft.com BITS Repair tool, but it is said that the tool is not necessary.

  I really need someone to help me and to understand this point for me, it's happened now for about 3 months. When I bought the laptop I had Webroot AntiVirus with Spy Sweeper installed, and I just installed Malwarebytes' Anti Malware, a week ago.

  Anyway, do the following:

  1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  1B. download the tool McAfee Consumer Product Removal, save it to your desktop: http://download.mcafee.com/products/licensed/cust_support_patches/MCPR.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. click right on the file saved in # 1 above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

  4. click right on the file saved in # 1 b above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then reboot again.

  5 test.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running.

  Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running. I can't enter to give more details. Can anyone help? There are a load of work due to deliver to the printing press Monday

  Have you tried to boot from the Partition Recovery and repair then the disc from there, using disk utility?

• G5 will not start. LED light on. Fans before working.

  Early 2005 G5. running 10.5.8.

  G5 will not start. LED light (no flashes not but solid). Fans before working. Rear fans blowing not. Cleaned up the dust. A exploded during a down and will not restart. Any thoughts? Is that a bad diet? What I would do. Thanks for any help. I love this old computer and hope to keep fixed and working.

  Sam

  Some of the fundamental things include the pram/clock battery replacement

  since they may be dead; then with a power failure, sometimes the Mac

  do not restart. Usual power management unit & reset NVRAM/PRAM are

  methods that sometimes also used as a troubleshooting measure.

  • Reset the Mac chip power management: (see SMU)

  http://www.thexlab.com/FAQs/resetpmchip.html

  • How to reset NVRAM-LANDAU on your Mac - Apple Support

  A hard reset can sometimes be used, where the power is disconnected

  the logic board and power removed from grill; Then push the Start button / stop.

  (But maybe not. Several PowerMac computers, I had, some people found this helpful)

  You may also remove and reposition cards and other items

  the inside of the case, to be sure they are connected properly. Be sure to not

  In short anything, due to the static load or residual power in the circuits.

  The hour is late here, so I'm not going offline; If all goes well a battery original or novel, etc.

  can help to put it on again. Also sometimes the power supply has some faulty fans,

  circuits or capacitors, so they can be troublesome to repair or replace.

  Good luck in this case!