PC AND PHONE MOBILE CONNECTION CHALLENGE

Similar Questions

• SonicWALL NSA 3600 6.2.2.1 - 14n and Sonicwall Mobile Connect for MAC DNS problems

  Hello

  I wonder if anyone has seen this problem. I just upgraded my NSA3600 to version 6.2.0 to 6.2.2.1 - 14n and now none of my MAC OS x clients that use the Sonicwal Mobile Connect application has no DNS. You can test by IP and use NSLOOKUP to find the records dns, but if you try to ping or access what either by its name it does not work.

  Everything worked perfectly before the upgrade to 6.2.2.1

  Thank you for this information, but it was not useful in this case because everything worked until I upgraded from 6.2.0 to 6.2.2.

  I just got got off the phone with Sonicwall support and there is a bug in the 6.2.2.1 - 14n and they gave me with a firmware fix. version 6.2.2.1 - 14n-HF156864-1n and everything is in working order.

• Two express AirPort and time capsule connectivity challenge

  Dear readers,

  I have a Time Capsule 802.11 ac connected to my ISP router and this is the router that provides DHCP addresses, etc. In our living room, I have an airport express (2nd generation) connected via radio and it works very well also. Now I got as a second AE (2nd generation) and want to put it on the floor of the attic to get a stronger signal via Ethernet to my TC. When I connect to a LAN of the TC port to the EI LAN port, the AE salon disconnects. When I add the Ethernet of AE cable in the WAN port both t he AE to the attic and TC disconnected. Currently, it is also connected via radio and it works, but will of course loose flow because it must still go through the different floors through the air compared to a stronger signal via Ethernet.

  Question I have, can I connect an AE with an Ethernet cable (and how to set up the AE or TC as a result) and an adverse event via wireless (IE editing exsisting which works, but let me know if you have to configure changes too)?

  Your help is very appreciated.

  Can question I have, I connect an adverse event with an Ethernet cable (and how to set up the AE or TC as a result)

  Yes, but you will need to restart and reset back to default settings AE. Then connect the Ethernet cable between a LAN <>- on the TC port to the "O" of EI before WAN port you are trying to configure EI.

  The problem that you are experiencing now is probably caused by connecting an Ethernet cable to an adverse event that has already been configured to "extend a wireless network. When EI is configured this way, is expected to Wireless ... not Ethernet. Ethernet is applied, it creates a feedback loop huge on the network which can cause all sorts of issues.

  Wizard Installation from Apple because most of the work for you. Just click the WiFi icon at the top of the screen of the Mac and then click on AirPort Express under the title of the new AirPort base station.

  

  When you click on AirPort Express, which will start the configuration "Wizard". It will take a few seconds to analyze the network, and then present a screen that looks like this:

  

  Type a device name you want to call the AE, and then click Next.  Monitor the screen following very closely... See the illustration below to confirm that the AE is set up "extend using Ethernet.  Who will confirm that the wizard picked the Ethernet between the TC and AE and apply the correct settings to EI.

  

  When you see the message Setup is complete, click done and you're done.

  If the 'other' AE is already set up to extend, then no further changes will be necessary on this device.

• Mobile connect 3.1.7 fails to check on IOS 3.1.7

  I have 8 Air Apple iPad devices, but 1 of 8 fails to check our Sonicwall TZ210. The only difference between the iPad, it's he who fails has the latest patches from Apple's IOS to the latest 8.0.2 version BEFORE I installed Mobile connect. All the others had the final Apple patch applied after the installation of Mobile Connect. I removed and renewed Mobile connect, I have reset the settings of the iPad to a base (although in version 8.0.2) and deportation machine Mobile connect, but it will not check. Someone has ideas about the place where else to go with this please?

  Brand please open a pension matter since no one seems to have heard about this issue.

• Samsung mobile phone - photo - says phone not connected - studio think that it is a Windows problem

  Trying to transfer photos from mobile phone Samsung D600.  Drive installed Samsung PC Studio 3.0.  It is good, but says "phone not connected" tried with Bluetooth but makes no difference.  The Assistant said that the two devices are connected.  Don't know what else to do. Any help much appreciated.

  Hi RubytuesdayTD,

  ·         What is the exact error message?

  ·         Did you do changes on the computer before the show?

  ·         What service pack is installed on your computer?

  You can run the Microsoft Fixit of the article mentioned below and check if the device is detected.

   

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Let us know if that helps.

• Help! I need to connect my iPhone5s to the stereo, but it has only one usb port and whenever I connect it, it connects? Is there a setting on my phone, I need to change? Help, please

  Help! I NEED to connect my iPhone5s to the stereo, but it has only one usb port and whenever I connect it, it connects? Is there a setting I need to change on my phone? Help, please

  You will need something like that and a micro USB to USB cable

  http://www.Apple.com/shop/product/MD820AM/A/lightning-to-micro-USB-adapter

• SG 200 - 08 p - PC connection and phones

  Hello

  We have a serious problem here with some new firmware for switches 200 - 08 p SG: 1.0.6.2

  They are installed behind layer 2 switches 2 SG - 200 50 - real firmware 1.3.2.02.

  We have 4 VLANS: 1 for 2 for the PHONE, the RPF MGMNT 10 and 20 for CUSTOMERS - and DATA on the VLAN only 08 P 1 + 2 is required. CDR protocoll is active.

  Ports 1-7 on the P-08 is configured as 'Trunk, 1U, 2 t,' setting: Auto negotiation WE. We tried FlowControl ON and - makes no difference. 8 port is configured as "Trunk, 1U, 2 t, 10 t" switch of the floor. The connection port on the floor switch configuration ist 50-switch of SG - 200 as "Trunk, 1U, 2 t, 10 t".

  One of the problem switches: on 1-4 08-p port is connected 4 phones Cisco 6921. On the 5-7 Port is connected 1 HP Z400 and 2 Elite 7200 PCs. 6921 phones is switching to a laptop DELL Latitude 6420.

  It so happens every morning, the first fixed PC ist works fine, then the switch must be turned to get the next PC connected to the network. Switching 6921 phone does not connect. But after a few more switching market of this walk.

  We thried another material 08-P with the same configuration, we tried an older firmware level... we configure ports PoE-phone as GENERAL 1U, 2 T. We gave to external power for phones that PoE is not overloaded... nothing doesn't. Only a few switching/disable help and the PC gets its address IP of the DHCP server and phones all come a discovery of the 6000 CU.

  Is there an outside person who can lend a hand on this?

  Thank you so far...

  Hi Mr. Jens-Peter,.

  I would try to disable smartports and ethernet green on SG200 switches.  Then you have to encode each of the ports to have the necessary settings.  Often when a reboot is required to restore the feature smartports is the cause.

  Regarding 6921 phones, you need to be sure to have auto voice vlan enabled.  Otherwise, the phones won't be able to pick up the VLAN correct via CDP.  Let me know, if you have any questions.

  -Good Trent

  * Please note the useful messages! **

• Is this possible with photshop and 13mpx mobile phone camera?

  Is it possible with the phone mobile camera 13mpx and photshop make image look pro like that? TNX in advance

  http://s1.postimg.org/ta3np201r/MV5_BOTc0_ODk3_Mzg4_OF5_BMl5_Ban_Bn_Xk_Ft_ZTcw_Mz_Iy_Nzgz _ OQ.jpg

  And here's one to correct color and tone.

  many https://helpx.adobe.com/Photoshop/How-to/Color-Tone-Adjustments.html?Set=Photoshop--Fundam image adjustment-

  You can find a lot of Photoshop tutorials from the forums home page. Find 'Adobe learning' in the second list box on the right, then click on the Go button.

  

• Tablet and phone Layouts not connected to the desktop computer

  In the instructional videos and documentation I've seen on Muse, it is said that there should be a + mark next tablet buttons and phone in map mode. I created a site of office but the + marks are not on the tablet buttons and phone. I know that I need to copy the content to the empty pages, but empty pages are not even created for... which, in turn, means me that page attributes and metadata must be copied layout available. Someone know how I can connect my layouts of Tablet and phone my office layout? Thank you.

  Hello

  If the sign is not there, it means the provision is already created, if you can not see empty pages when you go to a special provision, you can right click and delete the page layout. The sign will come back and you can add the layout again.

  Kind regards

  Aish

• How do I link my hp2540 of my Tablet and phone

  How can I sync my hp2540 to my Tablet and phone

  Hello @Estatebabe,

  Welcome to the Forums of HP's Support. I understand that you want to connect your Tablet and phone to your Deskjet 2540. I would like to help.

  I guess it depends if you are willing to connect through Direct wireless or use a current wireless network.

  It depends on what operating system is your Tablet and phone.

  You try to connect via Wireless direct or via a local network?

  If you try to use a local area network, the printer is connected to the network?

  Are your mobile devices using the Android Apple iOS operating system?

• new smart phone mobile access point causes bsod

  I used a Mobile hot spot on my smart phone to access Internet on my laptop successfully for 2 years.  I recently updated my phone (same brand) and now everytime I try to log in after a few seconds I get a blue screen and a memory dump.  I am running Vista.  Can I connect other devices such as my Ipad, but my laptop properly breaks down every time! My husband has a phone just as my old with the hotspot feature and my laptop connects to it without problem, but some affecting somewhere is not compatible with this new hotspot.  I don't know where to look again.  My phone provider says it's something with the OS, not the hotspot. My computer recognizes the wireless network and connect briefly - but when I try to go to a Web site, or after the screen a few seconds - blam - blue.  Error message says to contact my network administrator which is very useful. lol anyone have suggestions?

  Hello

  1. What is the accurate and complete error message you get?
  2. What is the brand and model of the computer?
  3. What is the brand and model of the phone?

  Method 1
  Step 1: I suggest to start the computer in safe mode with network and check if the problem persists.

  Startup options (including safe mode)
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2: If the problem is solved in safe mode with network then I suggest you perform the clean boot and remove the program that is causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: Follow step 7 clean boot KB929135 article to reset the computer in normal mode.

  Method 2
  I suggest you to update all the drivers from the manufacturers Web site:

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3
  I suggest you try the steps from the following link:

  Resolve stop (blue screen) error in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Note: When you run the disk check, you may lose some data that is corrupted. And also when you re-install Windows vista I suggest you to save the data.

  I also suggest you to provide the information in Event Viewer.

  Open event viewer
  http://Windows.Microsoft.com/en-in/Windows-Vista/open-Event-Viewer

• between my computer and router wireless connection (vista, premiem windows 7, 64 bit)

  Hey I recently had problems with my connection Wireless between my computer and the router.
  Normally off during the night is not connected to my router or on the internet the next day.

  I have been in close contact to my isp provider and have received a new router and reset my wireless Internet services provider site but I'm still having problems. I have also updated my drivers for my wireless on my laptop Hp G62 and have found that it will not cut when I do not shut down or sleep during the night.

  When you try to solve the problem, it will come back with "problem with the adapter or wireless access point and then asked to disconnect the power to the router. After doing this it will be fine all day.
  I do also to turn a blackberry 9000 "BOLD" and see first thing in the morning if the wireless is connected or not.

  ask for help, here is my last option I have been through everything and had an expert look at my computer where he found nothing wrong with my computer or wireless set up settings.

  any help or advice would be great

  Hello

  1. do you have problems connecting with Windows 7 or Vista?
  2. you remember of any change to your computer before the problem?

  Make sure that there is no interference between your router and your computer. For example. Mobile phones, like the mobile signals could conflict with your router signals and therefore no connection to your computer.

  You can uninstall and reinstall the Device Manager wireless network card.
   
  To uninstall the wireless device manager,
   
  a. Click Start, type device manager in the search box of start and press ENTER.
  b. Locate the network adapters and expand the same.
  c. Select the wireless connection, right click and choose uninstall.
  d. restart the computer, if prompted.
   
  Pilots should settle automatically after the computer restarts.

   

  Now you can install the latest wireless drivers and check if this solves the problem.

• New SonicWall Mobile Connect user

  Good afternoon

  I'm not a computer tech, I'm an end user (family doctor) and I'm desperate for any help, this is why I post here.  This is the problem, also short I can do:

  A week ago I bought a new laptop to access our home office computer system.  I already tried Windows 8, did not as he thought at all, so I would go for a MacBook Pro.  First time Mac user, usually takes a little after 20 years with Windows, but I like it.  Before buying, I checked with our technical office, who said: Yes, there should be no problem making remote access to our office with my new Mac system.  The Office Server running Windows Small Business Server 2011 Standard.

  So, I take the MacBook home and I can't connect.  I was on the phone all week last to our guys in tech support, who is off site, it has spent a lot of time playing with it remotely and he can't get it to connect remotely.  It installed SonicWall Mobile Connect on the MacBook, assuring me that it would work, but it doesn't.

  At least it sort of.  Here's where we arrived to help files in the SonicWall Mobile Connect:

  '3. when the connection is established successfully, the status line becomes connected and the connect button changes to Disconnect."

  Yes, this small works

  '4. Once connected, you can access your Intranet network with other applications. Mobile Connect menu bar icon will appear in the connected state:

  5. press the Home button on your iPhone, iPod touch or iPad to display the home screen. You can now navigate to other applications to access your Intranet network. The status bar at the top of the iPhone, iPod touch or iPad shows a VPN icon to indicate that the session of Mobile connection is always connected. »

  The status bar displays the Mobile Connect icon but nothing happens.  The apps on my laptop does not connect what no indication whatsoever outside of the laptop, and don't ask me what I should do next.  I sent our computer support "OK, so what I do next" guy but got silence.  So if anyone has any suggestions I would be very grateful.  Please let me know if you need more technical information.

  Thank you!

  Peter

  Please work with your Office IT Department to check that your VPN connection and the VPN server is configured correctly to provide remote access.  If your COMPUTER service needs additional support, please ask them to contact Dell Software support.

  There is additional documentation on the website of Dell, available software for Mobile Connect for OS X, including the 3.0 Guide here:

  https://support.software.Dell.com/SonicWALL-Mobile-Connect/Mac%20OS%20X/release-notes-guides

• Is there an event when the mobile connections are changed

  Hi, expert,

  I'm looking for an auditor check the following:

  1. when the phone is connected to a mobile network not connected

  2. when the phone is connected to another mobile network (another carrier or wifi) from current network

  3. the current mobile network connection is dropped.

  I found of initailly than ConnectionAttemptLIstener (http://www.blackberry.com/developers/docs/5.0.0api/net/rim/device/api/io/transport/ConnectionAttempt...). I thought I could use it to change mobile network connection. It turns out that I just couldn't. He listens to the event on ConnectionFactory which really is a connection on the connected mobile network.

  Did some research and I could not find any related information.

  So is it possible for me to achieve what I said at the outset?

  You can use a combination of CoverageStatusListener and RadioStatusListener to have access to these events.

  CoverageStatusListener will let you know what type of network access you have access from your coverage (by cell phone connectivity, etc.) WLAN network and which network transports are available).

  RadioStatusListener will let you know when the changes on the cellular network occur as signal changes, changes the base station etc.

  RadioInfo class can also be used to receive information on the current mobile network too.

  Kind regards

• My 5s iphone suddenly showed no service, then I made an attempt to update to ios and itunes connected, now iphone is not enable and display cannot connect to the server and in itunes it shows unable to check your device.please help me

  My 5s iphone suddenly showed no service, then I made an attempt to update to ios and itunes connected, now iphone is not enable and display cannot connect to the server and in itunes it shows unable to check your device.please help me

  Assuming that you have a valid SIM card in the phone, it is more often symptomatic of a phone that has been hacked or jailbroken to unlock.

  Where do you have the phone first?