Peripheral USB plug-and-play

Similar Questions

• How can I disable USB Plug-and-Play?

  Whenever I plug a camera into my USB port, Windows 7 treats as it has never been plugged in before.   When I plug my iPhone or iPad to synchronize with iTunes, Windows 7 starts trying to reinstall the drivers for it even though I just unplugged it five minutes ago.  When I plug my mouse, I get the same thing.  I use a laptop for the convenience of being able to unplug everything, put it in a bag and take it with me.  It is ridiculously annoying having to wait five minutes or more to start using my mouse whenever I put in place somewhere else.  Have to restart iTunes every time I plug in my phone, because Windows decided not to recognize the device even when I had just plugged in a minute there is delayed.  It is a stupid feature, and anyone he designed by default to this mode should be fired for being a fool.

  (1) you cannot disable

  (2) but you can disable the USB plug and connect service

  (3) START - RUN - type SERVICES. Enter MSC

  (4) in the right pane, find PLUG-AND-PLAY, then right-click, choose Properties

  and then MAKE some disabled

  (5) reboot your system

  (6) before the opening of the session, go to the BIOS settings, select USB controllers all THE

  (7) download and install latest correct chipset driver for your model of motherboard

  website of motherboard

  Good luck

• How we prevent USB plug-and-play for a specific device

  I have a plotter-cutter which is controlled directly by the software, not a pilot. It is USB connected. It works fine until Windows 7 Decides to install a driver and it then blocks the access of the program for the device.

  Windows then refuses to completely delete the driver information and then uninstall the driver and the software for the device is not entirely clear the problem back to blank pre-installation conditions. Even through the registry (after the uninstallation and removal of device) and removing the masses of references to registry keys that remain don't empty the system.

  I have installed the system on about five computers now and I miss.

  What I need to be able to do, is stop Windows from take control of that specific device without disabling USB or mess up the other USB device mode

  Hello

  I suggest you check out the following link.

  Guide step by step to control the device by using Group Policy

  http://msdn.Microsoft.com/en-us/library/bb530324.aspx

  Note: This link also applies to Windows 7.

  I hope this helps.

• Plug-and-Play drivers MIDI does not

  So, I recently bought a Vestax VCI-100, which is a feature of MIDI USB plug-and-play. Connect to my PC, it runs the dialog add new material, looking for drivers. After awhile, he gives up and says that it cannot find the drivers, which is strange because the device is supposed to be plug-and-play. It also happened a while back with a MIDI keyboard USB Generic. However, I have a keyboard more advanced (a M - Audio Axiom 49) that has its own custom driver that works very well. It's almost anything requiring the drivers of default plug-and-play MIDI which doesn't seem to work.

  What I discovered in my own extensive research, is that often this problem is caused by drivers Logitech Webcam creating inappropriate filtering at a level of register (my terminology may be a bit off here, lets say that I am an "intermediate" user). Unfortunately although I've never installed Logitech Webcam driver and I scanned the registry and cannot see any sign on the suggested potential cause.

  I also note that user; http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/8d33026c-f5a7-4fe2-8839-6cbdb04c5d6f complain of similar problems, that he believes was caused by its instalation of ProTools. Too, I have Pro Tools on my machine and during the inspection, Miss me the file "wdma_usb.inf". However, my Pro Tools installation is up to date, but the file is still missing.

  It is by far my best leader on what is causing this problem, but I don't really know yet. I would avoid a complete reformat if I can help it, but I can't find a reliable source for the correct version of this file. Can someone provide me with this file an instructions on how to install it? In addition, advice or suggestions are more than welcome.

  Thank you in advance, this has been frustrating me for quite awhile.

  Hi, Ben Murphy,.

  I found the following information on the site Web of Vestax:

  http://help.Vestax.co.jp/en/detail.php?id=110&id_page_url=83

  It seems that this only is not supported by Windows 7, but there is a possible workaround solution.

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• The plug-and-play USB mouse will not work on Satellite A100

  Hello

  I have a laptop Satellite A100 laptop and when I try to install a plug and play mouse windows says it is not recognized - unknown device.

  Please help the mouse works.

  Thank you very much

  Hello Jayne

  It will be really interesting to know where you're trying to connect the USB mouse. Can you send description of mouse models please?

  As I know it is not necessary to install a driver for external USB mouse and mouse is usually recognized automatically. Please check if a driver installation is needed, and even request delivered must be preinstalled.

• Windows XP SP3 USB errors / unknown devices with Plug and Play

  I have problems with USB flash drives and other plug-and-play devices detected by windows. After taking all possible measures to correct this problem (e.g. windows update, chip / update of the bios, update driver, driver and media ultilites reinstall, uninstall and allow windows update after restarting, removal of hidden devices and even remote tech support from Dell) whenever I connect a flash drive or use all plug-and-play devices it is detected as an unknown device and I can not put updated pilot any port I use. Hardware problems were excluded dute to recognition of the device and USB keyboard and USB mouse are functioning properly. Also these same plug-and-play devices worked well on other items of work. After Googling my eyeballs, I gave up and need help please. The only thing I can do now is to reinstall the operating system that really, really, I don't want to do.

  UPDATE *.

  Dell has replaced the motherboard and the problem was solved. Thanks to all here who offered advice and patience.

• Aspire Zs600 Aspire recognizes plug-and-play - plug device in usb and nothing happens.

  Aspire Zs600 Aspire recognizes plug-and-play - plug device in usb and nothing happens. How to solve this problem?

  try to reinstall the Intel chipset drivers:

  http://us.Acer.com/AC/en/us/content/drivers/4531;-; Aspire 20ZS600%

  Select your operating system and download the drivers from the Intel Chipset, and install it, restart, and try again.

  or

  Press the logo windows + x

  Choose Device Manager

  Click controller series universal

  Right-click on the Intel USB controller, and then choose uninstall

  Once done, reboot and wait windows re - install the drivers

• The devices plug-and-play USB do not install on XP pro sp3 that new hardware wizard cannot find the software.

  Running XP PRO with SP3 and the latest updates as of 12/14/10.

  Both a logitech M570 wireless receiver USB trackball and cause a cooler hub from the usb port 4 master the new wizard material to search for drivers but ultimately are not found.  Neither disks driver with devices or of are available on the Web sites of the companies.

  I also encountered the same problem with a new sandisk sansa mp3 player recently. It was recognized instantly on another computer running Vista.

  However, I have an eternal hardrive of WD and a recognized on my laptop XP Trendnet USB wireless adapter. In my view, that all have two drivers I installed earlier however.

  In the end, I believe not to be able to use the Plug-and-Play devices despite them being listed as compatible with XP.

  I removed the devices, restarted, nothing helps. Unknown poster USB 2.0 Device Manager hub and 2 other unknown devices.  I uninstalled the unknown devices in Device Manager and do it again, but no change.

  Don't know what other information I should include. Any help please, I'm at a loss what to tackle next.

  Hi pennybrown,

  Follow the steps below and check, if it helps:

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows:http://support.microsoft.com/kb/322756

  To create a new registry entry that disables the selective suspend of the USB hub driver feature, follow these steps:

  a. Click Start, click Run, type regedit and then click OK.

  b. Locate and then click the following key in the registry: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB

  c. on the Edit menu, point to new, and then click DWORD.

  d. type DisableSelectiveSuspend, and then press ENTER.

  e. in the Edit menu, click on change.

  f. type 1 and then click OK.

  Note: This setting affects all USB host controller drivers in the system.

  If the DisableSelectiveSuspend registry entry value is set to 1, the selective suspend feature is disabled. In addition, allow the computer to enable this device to save power power off the checkbox does not appear under the tab for the USB root hub power management.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unknown device message to an external hard drive USB... supposed to be plug-and-play

  I have a Western Digital external hard drive, 1 TB, I installed a PCI 2.0 card when I couldn't device works.  This has resolved nothing.  When I attach the hard drive, it does appear a message that says that the device is unknown.  I don't know how to fix the problem manually.  I contacted western digital, but be plug-and-play they provide drivers for their products and have referred me to your website.  Please help, its nothing more than an expensive paper weight at this point.

  Hi mgregurich,
   
  I suggest you try the following steps:
   
  Step 1: Find the error code in Device Manager

  1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  2. in Device Manager, look for the USB device, and then double-click the device name.

  3. under the gaze of general tab for the status of the device for any error code indicated.

  http://Windows.Microsoft.com/en-us/Windows-Vista/get-help-with-Device-Manager-errors
   
  Step 2: Run the fixit provided in the link below.
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Step 3:  Unplug the power and USB (universal serial bus), wait for a while and connect the external hard drive to another USB port and check.
  Also, connect the external hard drive on another computer and test if it works fine.

  If the problem persists,

  Step 4: Replace the USB controllers.

  First of all, please disconnect all USB devices and then perform the following steps:

  1. click on 'Start', type device manager in the search bar and press "Enter." If necessary, click on continue.

  2. in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click "OK".

  3. Repeat step 2 to uninstall all items under 'USB Bus controllers'.
   
  Then, restart your computer and windows vista will automatically reinstall all USB controllers.

  If the problem persists, please contact western digital for assistance.
  http://support.wdc.com/

  Thank you, and in what concerns:
  Ajay K
  Microsoft Answers Support Engineer
  --------------------------------------------------------------------------------
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My CAD U37 USB Microphone will not work supposed to be Plug-And-Play.

  I recently bought the microphone she appears under windows 7 as 'C-Media USB Audio Device' as it is supposed to, but it can't find the drivers. I talked to the developers, and they said that it meant to be plug-and-play drivers are native to windows.

  I plug it into my laptop which is running XP and it works very well.

  I tried all usb ports I have, I unplugged everything just got the mouse/keyboard and the monitor.

  Nothing seems to work, please help.

  Hello

  Please contact Microsoft Community.

  I suggest you follow the suggestion provided by Rajesh Govind responded on 19 March 2013 from the link below and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/my-headset-microphone-not-working-in-Windows-8/f4f1ad12-E7EA-4FFB-ac88-df5eed3298e6

  Hope this information was helpful and let us know if you need more assistance. We will be happy to help.

• Windows 7 printer and HP1120c using gigaware usb, a parallel printer cable is not recognized by plug-and-play

  I can't get my printer recognized by plug-and-play.  I have installed a printer manually, but still can not get to work.  All boards

  Hello Kirk,

  I'm not sure what you mean by "manually installed", but you need a print driver for the printer recognized by Windows. Go to this page to download the driver you need for whatever version of Windows you have: http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?pnameOID=14497&locale=en_US&taskId=135&prodSeriesId=25522&prodTypeId=18972&lang=en&cc=us .

  Once you have downloaded the right print driver, I let the computer do the installation.  NOTE: you may need to completely uninstall what you've done "manually" so that the correct driver is working correctly. See the HP Web site for more information (I'd do it, but I do not know what operating system you have and its depth of Bit (32 or 64)).

  Post here if you need further instructions or assistance (be sure to include your OS and Bit depth). Let me know how you fare.

  Kind regards

  BearPup

• Satellite M50 - YK4 plug and play mouse/keyboard

  I tried to use a USB keyboard/mouse for my laptop, but windows does not recognize it. They are peripheral universal plug n play and yet it takes me to the "new device found". I also tried to buy keyboards with software and despite the installation, the new hardware wizard still appears upward. When I try to install the drivers, it gives me just an error message (Code 10, device cannot start). When I bought my laptop, I could use my usb mouse and keyboard without problem, so I think that it's the corrupt drivers. All USB ports are working fine and my IPOD and phone, printer also work. Any help on this would be appreciated.

  Try to remove all associated USB drivers. Go to-> Add/Remove Programs Control Panel.

  Installation of the keyboard and USB mouse driver can cause problems, then remove both drivers. They work very well using the standard mouse and keyboard drivers.

  Another thing you can try is to reinstall the Intel Chipset driver.

• Windows XP 32 bit ceased to recognize plug and play devices.

  Recently, I had a virus and had to reinstall windows. After installation, I've updated all the drivers and Windows updates. My mouse, keyboard, monitor, and wireless adapter to work correctly. After about 3 weeks, I went to install my printer. I installed the hardware, but it could not connect to the printer. I followed the instructions of the manufacturer again and again but it never connects. His grateful sound because when I turn on the printer or offshore, I hear 'bing', but it doesn't connect. I used the "New hardware found" Wizard with the disc in the drive and it looks right and research, he never does the program on the disk. I tried to use the camera to Windows and the scanner Wizard with no luck.
  After that I gave up, I tried to use my camera, that has worked well until I reinstalled it and it happens "New hardware found" and the "new hardware detected" appears, but it does not recognize the CD, just look and watch for hours. I got fed up and finally bought a "plug and play" card reader SD and the bubble appears in the toolbar "new hardware found", but then the "new hardware found" stands and asks a disc! Its a PLUG and PLAY! There is no disc! The material is on the device! It's not my USB ports because he DOES not see something trendy and I checked Device Manager and he said his work without no problems found, but it does not connect to it. Does anyone have any info on what this might be? ANY help with this is greatly appreciated! Thank you

  Hi pressure,

  Peripheral Plug n Play need driver for the operation.

  PnP means that you do not have to restart the computer to install something.

  I suggest to update the drivers for the chipset of your motherboard and see if a firmware update is available for your BIOS.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HARD drive external, Toshiba PX1395E, not plug and play in Windows XP

  Hi all

  Thanks for reading this.

  Just bought a number of HDD 2.0 USB 750 GB external PX1395E.
  I want to use to back up files from my old computer to my new computer.
  In fact, my old pc recognizes the HARD drive (plug-and-play) and I already copied the required data.

  BUT: my new computer, with Windows XP Professional, Service pack 3. Does NOT recognize the HARD drive.
  I used several (versions 1.1 and 2.0) USB ports and everything is connected to the way that it should.
  Windows tells me that I have plugged 'something', but is unable to recognize what it is and I can't use the material.

  I think I need a driver to make this work. Site Web de Toshiba does not provide this particular driver (I checked, but it cannot find).

  Is there anyone with a solution?

  Thanks in advance.

  Do you see the HARD drive in the disk management?
  Control Panel-administrative tools-online-online disk management computer management online

  Another way is that reinstall you the chipset driver. Look at the Toshiba site to download and choose the right one.

  Look for yellow exclamation marks Device Manager.

  Let me know, what you're doing.

• Plug and Play drivers: Instrument of Identification error (pumps Ultra PHD at Harvard)

  Hi all! I use the LabView drivers to control a unit of Harvard pump 70-3007 and fall on some issues. (I'm controlling through the USB port).

  Driver:

  http://sine.NI.com/apps/UTF8/niid_web_display.model_page?p_model_id=16026

  Plug-and-Play site:

  http://www.NI.com/white-paper/3271/en/

  So I downloaded and installed the drivers and made sure that I have ALL the necessary software (USB virtual COM and VISA) installed. I then used teraterm (serial port communication software) to make sure my computer can communicate with the pump. He could.

  I then moved in labview, to make sure that my computer can control the pump. He couldn't. As soon as I try to screw attached with the drivers, I get an error. The first step in each VI is to call an Initialize.VI that makes a 'Identification of Instrumentation' stage, which always generates an error. He tells me that either I have wrong COM port (I assure you, I did not) or that the instrument drivers are not updated. HM.

  Any ideas? Of course, I know probably no one here has used this series of pumps before, so if there is no additional information / screws I can join, please let me know.