Phone IP Cisco CP - 9971 VCS registration...

Similar Questions

• Cisco TelePresence SX20 + VCS 8.2 Server and Skype for business 2015

  Nice day! My name is Dimitri! Have Cisco TelePresence SX20 + VCS 8.2 Server and Skype for business 2015. Is it possible to set up a conference call SFB and appeal to all subscribers of this conference? At present, we can only call on a single client and SFB. We have the current version of the software TCNC5.1.4.295090 SX20 - is it possible he obnoviti 7, and it will help to improve the situation? Thank you!

  I'm no expert on this technology, but I have some idea and already deployed some projects dealing with the integration of Cisco (CUCM, VCS) video infrastructure to Microsoft video infra like Lync. It would be the same process to make it work in your case.

  How does your deployed SFB? How do you do a conference for audio and video, participants can join the conference by dialing?

  • Mediation server would be required as a front-end server for you to integrate IP/PBXS using SIP trunk to enable voice (audio) Conference with the participants to the PSTN.
  • AVMCU Should be (Audio video Multipoint Conferencing Unit) will host the video conference that will include video endpoints as participants.
  • Video of Interop (SCREW) Server would be required to interface your SFB to third video conference infrastructure such as Cisco UCM or VCS for the endpoints Cisco call client SFB of endpoint of Cisco to participate to the conference organised on SFB by dialing the conference number.

  I'd say contact your AM SFB or Support as well for queries about how to plan your infrastructure SFB and direction.

  Kind regards

  Acevirgil

• Tests EX60 UCM and VCS registration

  Hello

  I did a few test with Cisco EX60 a few days ago a the following infrastructure:

  -UCM 8.6.2

  -Cisco VCS control X7.2.2

  -Cisco EX60 series

  -Csco EX90 series

  -Cisco CPIC

  -Cisco IP Phone

  The goal was to try to save the EX60 in SIP mode with UCM and H.323 mode in VCSC and make some calls with EX60 register in both devices, because I have found no documents where it was stated that only I can save EX60, EX90 in VCS or Complutense University of MADRID, but not in both at the same time.

  I recorded the EX90 in VCS and EX60 in VCS (H.323) and UCM (SIP).

  All calls to H.323 devices EX60 send control VCS and all calls all works fine without any problems. If I try to call EX90 to EX60 in SIP mode, the call will be fails. When the EX90 with EX60 H.323 call is connected, the University Complutense of MADRID and using RTMT I saw that the EX60 was on appeal or in busy state.

  -Audio call of the registered IP phone or CPIC to the AAU to EX60: I saw the call in the call control in the EX60 and RTMT and Complutense University of MADRID, but I did not see the call to the control VCS Cisco. If I try to call to EX90 to EX60 using H.323 right now, I got an EX60 busy tone. Also, if I make an audio call to EX60 for an IP phone I can do another audio EX60 call to an IP phone or an EX90. EX90 try to video negotited but calls finally was audio only.

  -The presence does not work when the EX60 is under appeal with the other end H.323 in the Complutense University of MADRID, too the BLFs do not work and does not appear the call at the Complutense University of MADRID.

  -Si EX60 is videoconferencing with EX90, the EX60 can receive an audio call to UCM get connect and the presence and the BLFs working properly.

  I find no more problems at the moment.

  Kind regards.

  This isn't a Setup program that you want to use, or register them both to the VCSC or

  Let CUCM control your end point, then h323 must be disabled.

• The call of CUCM phone IP registered to registered VCS VCS

  Hi team,

  Can us compose Cisco IP phones who are enrolled in CUCM to Movi Jabber which is registered to Cisco VCS, as you know movi jabber is not any extension then how we can compose to call manager IP phones.

  Is it possible to have the Conference with Jabber movi, not through MCU, means when jabebr movi is under appeal with the other guests, there is no option for conference or add the other party.

  Right answer

  BR

  I suggest you put a box on the VCS ENUM to convert numbers into URIs using NAPTR DNS records.

  See http://www.cisco.com/en/US/docs/telepresence/infrastructure/vcs/config_guide/Cisco_VCS_ENUM_Dialing_Deployment_Guide_X7-2.pdf for more information.

  Thank you

  Guy

• VCS registration issues.

  Hello

  No idea why I get the error very frequently below?

  Registration was not updated in time and endpoint did not reply to the IRQ

  VCS include the parameter "Time to" live in refractory ceramic fibers (registration confirmation) that specifies the interval (in seconds) during which H.323 endpoint must re-register to the VCS in order to confirm that it still works.

  If VCS receive none / updated QPP (application for registration) within this TTL, VCS will remove this endpoint of the table record.

  Normally most of the H323 device send new/updated QPP VCS halfway or 75% of TTL.

  He sees in general if the user simply stop endpoint after completed conference or loses network connectivity.

• Cisco Jabber (Movi) & VCS - E receives no video & audio

  I have a Setup with a VCS Expressway Starter pack (X7.1) where the 2 Ethernet interface is connected to an internal network on 192.168.x.x and interface Ethernet 1 is connected directly to the Internet (through a router to the Internet provider).

  Inside the network I have a few points endpoint TC5 & TC4 and a MCU. Communication of all these endpoints to the Internet works very well for the SIP and H.323.

  I also have a number of accounts on the VCS E Jabber/Movi.

  Registration of Jabber accounts to the VCS-E works very well to both internal and external networks.

  Use on these (v4.3) Jabber account on the internal network or external contact points of termination/SCM on the internal network, there is no problem.

  When you use the same Jabber account to call another endpoint on the Internet, I always a one-way communication, IE the Jabber does not get the video and voice.

  I took a few traces of the VCS-E network but did not find the problem.

  Any ideas what could be the problem?

  Rgds, Geert Folens.

  Greet them salvation.

  Excellent... I am pleased that it resolved your problem. I would be grateful if you set the thread as answered!

  See you soon

  Alok

• Cisco SIP of SX20 registration failed

  Hello

  I want to share the issue we encountered on an endpoint Cisco SX20 fails to register on a VCS control using the SIP.

  Endpoint is running version TCNC6.2.0. The other points of current endpoint of running on TC5x.x, TC6.x.x, TC7.x.x has no problem.

  The endpoint can register on the VCS, but when we try to call one of the other endpoints, the call is not successful. Endpoint will ring and when we accept the call, there is no audio and video, then call disconnects. After disconnecting the call, endpoint failed to register on the VCS.

  We have tried to re - register again, restart the system, then tried to make another call. Same problem again.

  On the VCS, we tried to create a subzone of this specific endpoint (subnet) with treat as authenticated policy. Problem persists.

  We also tried to restore the codec to factory default settings, but did not solve the problem.

  Search for your advice.

  Thanks for the help in advance.

  Thanks & best regards,

  Acevirgil

  Since you are using the version code TCNC, any encryption will not work for calls, if force you encryption anywhere on the VCS or see the call to try like TLS in the call history?

• C VCS registration issues

  Hello, I am facing problems of a new endpoint SX20 recorded in the control of the VCS, we received it with version 7.3.0 and each time it was recorded as a H323 device in the control of the VCS, has shown in the point of termination and VCS as good, but the h323 calls cannot be forwarded I checked the record in the VCS control and the RAS RAS Signaling as a 0.0.0.0:1719 location, the first thing that comes to mind was that a firewall can be malforming the package, I checked open ports too just in case about to endpoint and h323/q931 was open, otherwise he could not register at all. The I did a logging extended in the endpoint to capture recording debugged and found that endpoint sent the RAS location, signage with 0.0.0.0, generated from the endpoint itself, my question is, what could be caused by this problem? I upgraded to version 7.3.1 TCS endpoint, but the same thing happens, would it be a hardware problem? Whenever the system retrieves the IP endpoint of the NIC, to send it in the form of signs of RAS/places, there must be something wrong, the process or it receives the ethernet config? I have many other features of h323 of registered endpoints and works very well. Because now I have registered in the system as a SIP device, and works very well, which makes the VCS not interoperability, including the SIP registration confuses me, because it also retrieves the ip configuration and registry endpoint SX20 very well.

  Found the problem - under configuration H323 there is a parameter to the NAT, which had failed on 'On '.

  Set to 'Off' correction of the problem.

  I hope this helps...

• Cisco BE6k and VCS Center/periphery

  Hi all

  There is a new Be6k high density in the test environment.

  However, we have no clear idea about the VCS Core/edge with the CUCM deployment in the BE6k.

  1. We install the VCS core and edge on the same server BE6k? After that, the edge of the VCS awarded with a DMZ ip address? Or install the other edge of VCS of the device?
  2. What the configuration between CUCM and VCS? Because I can not any related document of the Cisco.com.

  Best regards

  Ben Lai

  1 both work, you just need to make sure good design and configure the underlying network and ports that connect each VM

  2 MANY West information on this

  http://www.Cisco.com/c/en/us/support/unified-communications/Telepresence...

• Cisco Jabber with VCS

  Hello

  I VCSC and TMS in the network, there are of the endpoints configured with SIP and H323. VCSC are not in the field.

  Now we have to enter Cisco Jabber with the VCSC. What are prerequisites them?

  First it requires license for Cisco Jabber on VCSC?

  We need to join the VCSC domain?

  Our VCSC is version 6.1 and TMS is 13.

  TNX

  Bobby

  Yes, you will still be able to authenticate users JabberVideo locally, 'right', you won't be able to use NTLM.

  Also take a look at the TMS Provisioning Deployment Guide:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/TMS/config_guide/Cisco_TMS_Provisioning_Deployment_Guide_13-0.PDF

  /Jens

• Conference MCU SIP with VCS registration question

  Hi all

  We have a cluster of MSE 8510 MCU (software version 4.5 (1.72), Build 6.19 (1.72)) with 86 active confeneces. All of them are configured in the same way, to use H.323 and SIP registrar calls control.

  The thing is, I can see all conferences recorded under H323 and some of them just registered as SIP on the VCS cluster (X.8.2.2).

  What is the problem? Why can't all register using SIP?

  See you soon,.

  Petar

  Can you check to see how many conferences are recorded using SIP?

  If it's 50, this seems to be the maximum that can be recorded, see enhancement request CSCum48651.

• Cisco IP phone 9971 recording on one control vcs

  Hello

  Can sombody please confirm is it possible to record the ip cisco cp-9971 phone on a cisco vcs control server directly. If possible, I appreciate a guide or a document for this. I have a vcs on x7.1 control.

  Thank you.

  Hi tof.

  Registration of cisco phones are completely different with the process how a normal end point sip/h.323 register on VCS

  When the cisco phone register it search TFTP get the firmware, which is obviously not available with VCS. Another important part to phone record 9971 are CTL file and other parameters that are not available with VCS and so what you're trying is not possible.

  See you soon

  Alok

• Cisco phone-8851

  I need to define a password phone my Cisco phone. I already have the administration password.

  One can call from my phone when I'm not in my seat. So, I need to put a password for my own good.

  Please help me find a solution.

  Thank you

  Jayan

  Hello

  Google 'mobility extension '.

  With this feature, you can configure the phone's base only be able to dial in their own country. When you log in, your settings of the line and DN are applied which can compose outside.

  Concerning

  Aaron

• What is the difference between the video of Cisco Jabber of jabber, WebEx, Cisco

  Hello

  I started reading about Cisco jabber for a few days. I couldn't make out the clear disctiction between Cisco Jabber, WebEx and Cisco Jabber video. What is the difference? Also the one who uses the API of the other? What is APIs that WebEx Cisco Jabber or Jabber user video using the WebEx API?

  Thanks in advance :)

  Does this help: http://www.cisco.com/web/products/voice/jabber.html

  Jabber is a BRAND name for a range of products to run on a variety of devices.  Mainly desktop and mobile.

  It requires not more CUCI.

  WebEx Connect (with CUCI Connect) is/has migrated to Jabber

  CUPC is/has migrated for jabber

  The Jabber SDK is very powerful (url above understands this as well)

  Jabber for telepresence is the old MOVI (Mobile Video) of the Acquisition of Tandberg and more than one piece of theater for VCS registration and control.  But most of the jabber brand above 4 video.

  There will be subtle differences between different brand of jabber clients, so don't read a J4Windows guide and think it's the same for the iPad or Android for example).

  But its great.  Head to head with Lync.

• call the problem with ip video phones

  Hello world

  We have a video infrastructure where

  (1) vcs control x7.1

  cucm 2)

  (3) SME session manager edition

  call flow between endpoints

  video endpoint-> control->-> cisco cucm area vcs session manager-> cucm-> cisco iphones edition

  facing problem

  (1) while the call to the ip video endpoint phones video, he shows is not the E.164 no (caller ID)

  audio/video 2) not received when calling video endpoint video ip phones

  attached are the newspapers of vcs xstat and vcs xconfig

  Rashmi,

  No problem. If possible mark the thread as answered

  Thank you

  Alok