Photosmart c4580 print problem

Similar Questions

• Photosmart C4580 print without wires after installing Snow Leopard

  Hello. I recently installed Snow Leopard on my MacBookPro. Since then, my Photosmart C4580 print wireless. I checked the updates of the software and the message computer read that I was up-to-date so I don't know what to do. Any suggestions?

  Geez-you are a genius! Thank you very much - your solution has functioned perfectly!

• HP Photosmart C4580 Wireless problem - Snow Leopard

  Hello

  My HP Photosmart C4580 has worked for wireless (albeit a bit slowly) until I made 2 changes:

  (a) I changed my router SSID (network name) and password

  (b) I have upgraded from Leopard to Snow Leopard

  At first I tried to use the HP configuration utility to reconfigure the network my printer wireless.  It doesn't not work - he told me that my printer to be connected via USB, while he was already.  I tried different things and ended up reset wireless to the printer (using the printer menu).

  Then, in the HP that I read that HP utilities do not work with Snow Leopard help files.  But the instructions for wireless network with my snow leopard printer did not work.  I could install my printer via USB (and downloaded driver), but it does not appear on the list without wire.  I couldn't find a way to configure wireless with USB connection, as I already had when I initially set up my printer with Leopard.

  Video instructions to set up wireless for Mac (http://h30434.www3.hp.com/psg/board/message?board.id=Macintosh&thread.id=231) seemed promising, because it would finally give me a chance to give my printer on my network information.  Wireless Network Test report gives the network name (SSID hpsetup) (since I have reset the settings), that I found promising, although only under IP address, he said 'not applicable' (and obviously fails it test under 'Network name found' failed-it).  However, my macbook can't take any hpsetup network and on the network Page Configuration I printed the network status is 'offline', Active connection Type is None, URL is 0.0.0.0.  Apparently my printer cannot connect to this network hpsetup.

  I have spent a few days on this and I am completely at a loss to know what to do.  Can someone please advise?  Thank you very much.

  OK, we can solve the problem.

  First you uninstall the 10.5 HP software before installing 10.6?  If this isn't the case, we might as well do it now.

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt, as well as Apple and click on uninstall
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled, this is why we do not run this thing all the time)
  Click on continue
  Let the cleaner it is.

  Then, remove the printer in System Preferences, Print & Fax.

  After that, go to hp.com and download the 10.6 complete package

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=OJ-74785-1&LC=en&DLC=en&cc=us&lang=en&OS=219&product=3418707

  Having attached to the C4580 usb cable and select Wireless when you can.  Follow the rest by.

  I noticed problems where people have "special" characters in their password wireless.  If it fails, and you have no alphabetic characters or digital, you will need to go through the process of hpsetup ad hoc, as detailed in the video you mentioned.

• Blocks wireless HP Photosmart C4580 printer

  Hello

  I have a HP Photosmart C4580. It was connected to my Wireless network. The other day I decided to change SSD and WPA key my route for security reasons. The printer has stopped working so I again installed the software so I could configure the network printer information.

  Problem is that now it never acknowledges that the printer is active wireless. I tried in a computer with XP and a macbook pro with snow leopard. In both cases the critical points of configurations in trying to find the printer. I realized that something happened to the printer wireless radio, because when I run the printer, the wireless has become active and then it stops just the printer. The buttons and the display of the printer becomes simply does not. Likewise, I can't get the printer because the power button is unresponsive. I have to disconnect the printer taking and during startup, go to wireless menu and turn off the wireless radio, so it is not blocking the printer quickly. I also (at start and quickly) restored the default radio wireless configuration. But that has not solved the problem. Also tried to reset the printer unplug the power cord in the back and in the decision-making. Nothing has changed.

  I have no idea what makes the printer freeze. Probably something with the edge router? I just change the WPA key and SSD.

  Thank you in advance.

  Hello

  Take a look at this ad because it has a solution on the WPA encryption Open to change.

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/C4580-change-wireless-settings-from-open-to-WPA/TD-p/158877

  This should give you a few pionters.

  Good luck

• Photosmart D7460: Printing problem

  When printing some elements such as greeting cards or business cards, my printer reproduces all part of the bottom of the print at the bottom of the card.  This does not occur when you print from Word or other programs of type, nor happens when I print photos.  Only on maps.

  Any suggestion would be appreciated!

  Hello @IreneD and welcome to the Forums of HP, I hope you enjoy your experience!

  I see that you are experiencing printing problems. I would like to help!

  I would recommend starting with a power reset.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I recommend also to download and run the HP print and Scan doctor.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• Photosmart C4580 wireless problems after installing Snow Leopard

  Hello

  I recently installed the new Snow Leopard on my macbook to see I have printer problems.  I tried to uninstall the HP printer and reinstall.  I can print if I connect with my USB, but I can't make it work wireless.  When I try to print wireless, printing opens and tries to print.  Then I get an error message saying that my printer is offline.  How can I make 'online '.  This error message disappears when I plug in the USB cable.

  I would really like my printer works as well as it did before Snow Leopard.  Maybe that's not possible, but I would at least the option of wireless printing.  I've been waiting with the help of HP for 20 min. twice and finally abandoned.  Any help anyone could give me would be greatly appreciated.

  Thank you very much.

  LSteph

  Isteph: The main reason for you trouble is that you send the job thanks to a USB print queue configured. Each queue on a Mac is specific to a single connection method. Printer offline is the Mac error, which means the cable is not connected (of course it wouldn't be).

  To fix this: open your menu Apple - system preferences - Print & Fax. Use the 'negative' at the bottom of the column to remove from the queue for this device. Click on the "plus" sign to search a new queue. You want to add a queue of bonjour for wireless connections. If a queue of Hello is not displayed then PrintDocs instructions above may help you to re-associate the printer to the network.

• Photosmart C4580 wireless problem

  This all-in-one is not responding when he slowed down after a few hours without exploitation. The only way to bring back to life is in power it cycle. I tried the reset default, static and same ip address assignment to disable security on my network. Still the same problem. The only solution provided by HP support must it off when it is not in use. I think that's not a real solution for me. I really regret buying HP printer. If anyone can help it would really appreciate.

  Photosmart 44xx series

  Photosmart series 45xx

• Photosmart HP: Printing problems with my HP Photosmart

  I had problems with my photosmart for awhile. For a while, when I would plug into the usb port of my computer, I had received the error "the disk you inserted is not readable by this computer. I used to ignore the error and used to print anyway.

  Yesterday, someone pushes my printer without unplugging the usb by behind. Now, when I try to print something, I see in the queue of the printer, the error message saying "communication error: the computer is therefore more able to communicate with your printer." "Turn off the printer, check your printer connections and look for errors in the printer and turn on the printer. I got it done and straightened my computer as well, but it does not work. After that, I opened the printer utility via my computer to print a test page, and it worked really, which is strange.

  Thanks for your help,

  Sarah

  Hi @stoukan,

  I see that you are getting the error "communication error: the computer is therefore more able to communicate with your printer." Turn off the printer, check your printer connections and search for printing errors and turn the printer. I would like to help you today. If this helps you to find a solution, please click on the button "" accept as Solution"" down below this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  What is the name and the product number of your printer? How can I find my model number or product number?

  Turn on the printer and make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation. The USB cable should not be more then 6 feet. Make sure that the USB cable is connected directly to the computer. (not a station or a hub) Try a different USB port on the computer. Check that the USB cable is connected to the appropriate port on the back of the printer.

  Check if the Mac sees the printer is connected.

  Go to the Apple, select about this Mac, system report, select USB.
  Do you see the printer listed?

  Fix permissions of the drive on the Mac:
  Close all applications.
  In the Apple menu, click OK, click Applications, and then click utilities.
  Double-click disk utility.
  Highlight your hard drive / partition on the left.
  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click on the Apple icon and then click on System Preferences.
  Click on Printers & Scanners.
  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.
  Click OK to confirm the reset.
  Type the name and the correct password.
  Click OK to reset the printing system.
  Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the name of the printer) Then click the Add button.

  Try to print again.

  If you're still having problems, please try another USB cable.

  If there is anything else I can help you, let me know. Thank you.

• HP Photosmart D5460 printing problem using the cd/dvd tray

  Just bought a HP Photosmart D5460 solely for printing cd/dvd directly on cd/dvd labels.

  The problem I have prints a label on a Verbatim CD Vinyl.

  It is a normal 80 min CD - r but with an edge of vinyl and a 70mm print Center.

  When put in a fake cd (12mm diameter) cardboard, printing is excellent, exactly as it should.

  But as soon as I put in a CD of vinyl, the label is printed below the disc on the disc tray - holder, approx. 80mm below the mark where it should be.

  It drives me crazy, that everyone has seen this error before?

  Calibration is not help me... Also used almost every label possible software out there (Surething, Acoustica, Nero and Photoshop plain) who all give me the same result.

  Yes, I think that's the problem.

  I cut out a circle of plain white paper, which is the size of a cd and cut out the Center (a little more fat then 70mm of the printable area of the disc). Put on vinyl with tape adhesive tape and now it prints exactly on the label, to make it work.

  The black color of the disc must be the problem.

• Driver of HP Photosmart C6280 printer problem

  Hello!

  I bought the above mentioned model printer, and I installed the drivers in the manner recommended by the manual. The printer works well and does what I expect from him. But there is one thing that annoys me.

  The printer is connected to my home network

  Drivers are installed on all (two) computers in my house.

  On my old trusty laptop running Windows XP Pro, it works very well, but when I connect it to a network in other places, a svchost.exe process starts to run at 100% and to use all free CPU resources in my computer. This svchost running a process called HPSLPSVC. If I reconnect the computer on my home network, it comes down to normal loads of CPU again.

  Is it possible to 'reverse', the printing software to say when I'm not at home? This situation of CPU load makes the computer run the much more common fan, which is annoying in addition to one.

  I hope to have this work, or I'll be forced to install a queue shared on my home server.

  / Noralf

  We have a work around for now, he must first install both files to patch the operating system from the following link: = http://support.microsoft.com/kb/927891 = here's the instructions on what to install the web link above: after opening the link, you need to install 2 patches. The patches to install are given below. "Download and install update 927891" & "download and install Windows Update Agent (WUA) 3.0" after you have installed the two patches, you must restart the computer and check the result. If the problem persists, we can perform the steps below. II. "HP Network Device Support" service stopped: the steps to stop the "HP Network Device Support" service are: 1. click on start, then run and in the run window, type services.msc and press ENTER. 2. Locate the service "HP Network Device Support" in the opened window of Services 3. Right-click on it and select "Stop" and close the Services dialog box. III. Add HPSLPSVC32. DLL file in the firewall exceptions list: Add 'HPSLPSVC32. DLL file"in the list of exceptions in the firewall, perform the procedure below. 1. click on start-> run. 2. in the Run dialog box, type "firewall.cpl" and press OK. 3. Firewall dialog box Windows will open. Select 'ACTIVE' option. And then click OK. 4. yet once, perform the steps above to open "Windows Firewall" dialog box. Then select the tab 'Exceptions' 5. Click on "Add program"-> "Browse". 6. Select ' "C:\Program Imaging\bin\HPSLPSVC32 HP.". " DLL' after the completion of the steps, click on apply and OK. And restart the computer to save the changes. Once you restart the verification of the system for the result and we do know the result so that we can help others also facing this problem.

• Photosmart C7180 printing problem

  So, here's a strange, my Photosmart C7180 age of 9 months has developed a bad habit to print all pages in landscape mode. I used the printer almost daily for 9 months, but 2 days ago I started to notice this weird quirk when printing multiple-page documents. I can't verify what may have triggered (this software or an OS update) because it is possible that I haven't printed documents several pages for a few weeks. I checked for the OS/App/Firmware updates and checked that I have the latest drivers and software. I restarted the two systems and reset the default settings for the printer.

  I can print a single page in Portrait mode, but if I have 3 pages print the 2nd page comes out in landscape. I can print the 2nd page individually and it is fine. It happens that I print from Microsoft Word, or even if you use the Microsoft Photo Editor or HP Photosmart software.

  I use the TCP/IP connection to print from my laptop Microsoft XP (even though I just checked that this happens when you use Bluetooth as well).

  Everyone knows it or have one could explain why it seems to be possesed?

  Hello

  try turning off the advanced printer printing functionality

  > Control Panel

  > Printers and faxes

  > right-click your printer icon by default which is c7180

  > select Properties

  > click on Advanced tab in the Properties window

  > uncheck the box saying ACTIVATE a FEATURE of PRINTING ADVANCES

  > hit apply, then press ok.

  > then try to print your documents

  Kind regards

  Kiko

• Photosmart C4580: How can I configure my Photosmart C4580 printer for wireless printing?

  Hi, I changed my wireless network name, so my printer is no longer connected to it.

  I tried to set up the new name wireless using Windows 10 but I can't figure out how to do it. I tried to do by using the HP Solution Center software, but I get this message (see photo).

  Can anyone help to reconfigure my printer?

  Thanks for your help.

  Hi XE1RDR!

  Let me show you how to install your printer to your computer windows 10. But let me put your expectations that the printer driver may or may not work because it has already exceeded and your current operating system is the latest Microsoft.

  Well, lets move on to serious things.

  1. first of all, you must have the printer attached to your computer USB cable/cord.

  2. then download the driver complete features of the printer by clicking on the link: http://support.hp.com/us-en/product/HP-Photosmart-C4500-All-in-One-Printer-series/3575173/model/3575174

  -Select SOFTWARE and DRIVERS

  3 download the full driver

  4. run the file and install the printer through the USB port

  5. once the installation is complete, run the program again

  6. this time, select CONVERT to without WIRE USB

  7. continue with installation and the last part should ask you to remove the USB cable to complete the installation

  Your printer must be set by default, and then try to print.

  Good luck bro!

• HP Photosmart D110: printer problem

  I feel multiple copies and printing started to look like it when ink is low.  I put in a new cartridge and made the steps to align.  There is no error message but when I check the status of the printer it tells me the ink levels are full and it is ready to print but... it copies still look like they do with the low ink level.  A few lines of print OK but most are too light.

  Well - I printed just a test page that you suggested and it's perfect.  I have nothing new since yesterday except leave him alone because I had to go to work.  Apparently it was just a day.  Thank you very much for taking the time to help me with this.

• Photosmart C4795 printer problem - cannot print from my HP laptop

  I tried to run the diagnostic tool. It indicates that the printer is offline. I can't understand how to reconnect. I have windows XP.  I was on the phone with ATT/HP for more than an hour with no resolution. Help, please!

  Reinstall the software and drivers from here.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=3940574

• Photosmart 7520 printing problem

  My printer prints a message every 45 minutes: CONNECT to h20629. www.HP.com:443 HTTP/1.0

  Hi Yambury,

  Thank you for your answer!

  Please, try the following solutions:

  1. The firmware was updated. Get the latest Firmware and updates.
  2. Go through the steps described in this guide without wire. The printer keeps Wi-Fi connection.

  Hope this helps you and have a great day!