Photosmart C6180 turning on the problem.

Similar Questions

• Photosmart C6180 cannot detect the wireless network

  I have a Photosmart C6180 for over a year, and until recently it connected wireless very well.  But since a week ago, it can't detect the wireless network.  I turned off the printer and wireless router several times each without success.  The "Wireless Setup Wizard" running on the C6180does not help. Watch simply screen printer "looking for... wireless router. "indefinitely, until the function Cancel.  The wireless router is about four feet from the printer, in a direct line of sight.  In addition, I have wireless Internet access using the same router and continue to do this successfully, then the router itself works.  Recently I have updated the firmware on the router as well (after the beginning of this problem).  Running the network Test report wireless on a 'PASS' C6180 returns for "Radio on" but a "FAILURE" for "use of Radio". The radio broadcasts as "about" section of the Menu Radio wireless network.  My router is a Belkin Wireless G Router model F5D7230-4.  The printer prints very well with a wired connection, but wireless connectivity has been a key reason behind my purchase.  Any suggestions greatly appreciated.

  Sorry, but your wireless radio is dead.  Its time for a new printer.

• Photosmart C6180 repeatedly loses the wireless connection

  Hello

  I have a mixed network of linux and windows PC as a Photosmart C6180 wireless access via a Netgear (DG834GT) wireless router.

  It works very well for over a year, but recently the printer keeps dropping the network.

  Show all PC (linux and windows) as offline and the router says that this isn't one of the connected devices, and I can't ping it.

  However, if I look at the State of the network on the front panel, it says which is plugged, and if I print the network status page it shows the active connection, wireless and watch as loan.

  This isn't a DHCP problem. The printer and all PCs have static IP address settings.

  If I change the printer market once again, it connects to the network, everything is OK and I can print, but a few minutes later it disconnects again.

  For now, I'll have to pass it works whenever I feel - please help!

  Thank you

  JohnT

  Hello

  Thanks for your suggestions.

  It seems it might be a problem with netgear!

  I rolled power the router netgear (normally on the left) and the problem seems to have disappeared.

  Thanks for your help.

  Concerning

  JohnT

• Turn off the problem on Satellite Pro A210

  I'm having a problem with my Satellite Pro A210, running on XP. It seems to turn off without reason. I don't think it's a problem of overheating as it can sometimes after only a few minutes of use, and can stay on the day without problem. It is as if he goes into hibernation, although the blue power light remains on, but cannot be restarted without turning off the power and then walk back.

  Someone at - it ideas? Thank you.

  Hello

  could you please tell me the following things:

  1. which modelnumber does your machine have? (you can check on the nameplate on the bottom of the machine)
  2. what version of BIOS is installed?

  Welcome them

• Alienware 17 R3, 15 R2, R2 13 not turning on the problem (the reason + FIX)

  Many people including me have exactly the same problem where their Alienware Laptop lights once you stop him for no reason at all. Now, people DO NOT panic! There is nothing wrong with your hardware. The laptop is perfectly fine. What is causing this issue is the BIOS they come out (1.2.12, 1.2.13, 1.2.14) these BIOS cause this problem ive never had an issues before on the latest bios of 2015 that was installed on the Alienware when I bought it until I've updated the above bios. Alienware I please ask you to not release a bios that would cause problems to people and please do some intensive tests before releasing anything. The sticky on the forum here has fixed the problem though, but he may return.

  This will solve your problem, it is said in this link install BIOS 1.2.13 or more, BUT DO NOT, and instead when the computer turns on after you follow the instructions for the fix mentioned in the link below, download BIOS 1.2.8 and install it, then 1.2.8 after you won't have the problem more.

  http://www.Dell.com/support/article/us/en/19/SLN301252

  1.2.8 is BIOS, I recommend to all install on their computers laptops alienware

• Photosmart 7510: turn on the scanner only

  I scan more print and want to turn on my scanner without initializing the printer function (and therefore waste). can I do this?

  The printer functions are initialized when the 7510 is turned on, you cannot switch on the scanner separately.

  I suggest that you keep the printer plugged directly into a socket slot - if you use an external switch as a switch taken out of ink will be used when the printer is on.

  The Photosmart 7510 enters a low power standby state, you might consider leaving the printer 'on' and leave the management of the ADF to take care of things.  The Photosmart 7510 is Energy Star rated.

• HPD0FES5 HP Photosmart 7510: turn on the menu screen on the front of the photosmart 7510 either. Why?

  Screen menu on the front of the all in one HP machine on light up more. I'm on longerable to use the fax feature,

  the feature to copy or scan function. I'm still abe to send print jobs to theprinter to my laptop. Any ideas?

  Hello

  Please try the steps below...

  -While the printer is turned on, tilt (up/down) the screen and check if it has the icons.

  -Unplug the power cord from the back of the printer.

  -Unplug the power cord from the router.

  -Wait 60 seconds.

  -Connect the power cord to the back of the printer.

  -Wait until the power the printer on.

  -Once the printer displays the icons of the House, you can then put on the router.

• My new Xperia XA of the ultra network turn catch the problem!

  Initially I bought Xperia double M5, but it's a completely defective unit! And finally, who had died! Then after 3 months harassing Sony Center replaced me a XA ultra new Xperia.
  I use it for 13 days until now, I am facing problem with the signal from the network! He can't catch the Tower network correctly! Where other mobile do with the same network operator at the same position with complete tour! Signal bar is always as a point! Never complete! Smoking 2 or 3 bars at least! What the * beep * Sony! I am from Kolkata and I use AirTel sim. Already taken a new nano Sim, so no card sim or network problem!
  Now help me guys... Please. What I can do...
  Thanks in advance

  Do not lean on the bar, do this with two phones

  Settings > about phone > status > signal strength > what do you see?

• Turn on the problem.

  How can I get my iMac to propel to the top? He gets to midway up and then stops.  Have you tried the unplug and hold down the button bugs and that they did not help.

  What you're saying, looks like your iMac's hard drive is damaged. OS X will try to repair the disk at the start, but he can't and he died in your Mac.

  The best thing to do right now is take the Mac at the Apple Store or dealer to get a diagnosis or repaired. You can also try to boot your Mac from OS X Recovery (if you bought your iMac after July 2011 or if you are on OS X Lion or newer) or the Mac OS X installation disc and run utility disk to see if he can repair the disk, but this probably will not work. I really hope that you have a backup of your files, because you'll need.

• HP Photosmart C6180: hp photosmart c 6180 turns off when it is connected to the network and blinks green photo

  When my Photosmart C6180 is related to two wireless and ethernet network after any number of hours it stops itself down and the green light on the front panel by the icon of camera flashes.  You will then have to push the power button to turn back.  Not very practical for a network printer. Router is a Linksys WRT 1900 ACS.

  Hi wjabdella,

  Thank you for your answer!

  In the post I provided on the hard reset, he mentioned: sometimes, when plugged into a surge protector or battery backup, the quantity of electricity is not received by the printer.  Power problems can cause printing problems.  It is particularly important to be plugged directly into a wall outlet with wireless connectivity problems, "sleep mode" and other power problems.

  So by unplugging the power and waiting, it resets the printer almost to its original state without making a complete factory reset and lose any other information.

  Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I hope that answers your question!

• Photosmart C6180 problem of Power-Up/Power-Down - loops on/stop/start/stop etc.

  I had the C6180 Photosmart wireless connected to a Mac OS X 10.5.6 laptop Macbook Intel and IBM PC XP SP 2 for more than 2 years.  I did have major problems with the printer.

  Recently, I have known a couple of electric in my house.  Since then the printer has turned off randomly once or twice.  Today the printer began to turn off/on/off/on/turned off/turned on etc.

  It lights up and shows the HP logo and process bar animation for one minute, followed by the message: "abnormal termination.  To avoid damage on the button to turn off the printer.  Do not use a wall or the band switch to close.  Press OK.  Then he stops and leaves upward.

  I tried to enter batch Mfg mode by organizing the * and # keys.  It flashes "Mfg commands - enter special Key Combo" for the second of two, then stops and makes a loop on/stop/start/stop again and again.

  I have disconnected all data cables, installs the printer in another room, closes the wifi on both computers and connected directly to the wall on a different circuit to eliminate problems of low power as the culprit.  I swapped the power cable between the wall and the block of the AC adapter with the same exact type of cord of another piece of equipment with the same results.

  I wonder if it is a symptom of a surfboard logic damaged in the printer, or a problem with the AC adapter?

  If it is the logic board, does pay to get it fixed?  An equivalent printer for Mac would cost about $200.  Not to mention that I came just to have stored on cartridges.

  What is a likely indication of a problem of brick AC adapter?  If so, should I spring for a replacement block AC adapter for $30?

  I was not able to find this question in a post on the forum and I was wondering if it's 'Au revoir' to the C6180?

  Thank you for your contribution to this number

  Try this:

  1. If the printer is still on, unplug all rigid and flexible cables at the back of the printer.

  2 unplug the power cord also from the wall...

  3. wait for two minutes.

  4 reconnect the power cord to a wall outlet first.

  5. hold the pound (#) and six 6 buttons.

  6. all by pressing the two buttons, reconnect the power cord to the back of the printer and at the end of two seconds, exit book and six buttons.

  7. turn on the printer if it goes out...

  Let me know the results.

• Power problem: Photosmart C6180

  My printer Photosmart C6180 continually lights stays on for about 30 seconds and then seems to lose power.

  I tried the troubleshooting steps already using different points of sale and unplug power for a period of time, but nothing has solved this problem.

  Someone know if it sounds like a problem with the printer or is there something wrong with the power supply?

  The printer was working fine a few days ago, nothing happened that may have caused damage that I know.

  Thanks for any help you can offer!

  Sorry, I should have searched the forum more carefully before posting, I found the solution to my problem.

• Photosmart C6180 - unable to delete the document in the print queue

  My Photosmart C6180 shows a document in the queue which can not be removed causing the error message and unable to print documents from my laptop.

  Hi Thomastwhilaker,

  I'd love to help you remove the paper that is stuck in your queue and get you print again.

  First post please returns with the answers to these questions.

  1. Is the printer connected wirelessly or with a USB cable?
  2. The printer is connected directly to a wall outlet or a surge protector? (It is preferable to connect directly on the wall)
  3. You have all other printers HP installed on this computer? If so, do you still have the printers?
  4. Is this a HP laptop or another brand?
  5. What operating system do you have? Mac or Windows?

  At this point because you said your 'portable' I imagine you have Windows. If you have not already tried the HP print and Scan doctor, please do and let me know the results. You will see a key, a yellow exclamation point, a red X, or a checkbox then each point tested. If you have a Mac, skip the following steps and let me know.

  

  Click here to download and run the utility > HP print and Scan Doctor

  If the problem persists, I suspect that if restart us the spooler, remove the driver and re - add the printer that we may be able to correct the problem. Follow the instructions below to perform these tasks.

  Restart the print spooler

  Hold down the Windows Logo key () on the keyboard and the 'R' to open the Run dialog box

  • Type services.msc and press enter
  • Locate the print spooler and double-click it to open the spooler properties
  • Make sure you that Startup type is set to automatic, if not please click the menu down and select automatic
  • Under Service status, please stop the server, wait a moment, and then click Start

  Remove the printer from the server to the printer properties

  1. open the folder "devices and printers".

  2. choose "print server properties.

  • Win XP - with no printer selected, click 'File' then 'server properties '.
  • Windows Vista - with no printer selected, press 'Alt' and then click 'file' then 'server properties '.
  • Windows 7/8 and 8.1 - Select any printer in the "Devices and printers" folder and click on "Print server properties" above.

  3. click on the "Drivers" tab at the top of the window "properties of the print server.

  4. choose the printer that you want to uninstall, and then click 'remove '.

  5. choose "Remove driver only.

  6. the next screen will give a warning, letting you know that the removal of the driver package will remove it from the system. Click 'Yes' to say are you sure you want to do.

  If you get an error "in use", restart the computer and the printer, and then follow the steps again.

  Re-add a printer

  Open start > all programs > HP folder > folder printer > HP Setup and the software if you do not see the program installation and software, but you see the printer icon, double-click the printer icon to start the installation and the software.

  Please let me know if this does not resolve the problem, or if you need additional help, I'm happy to help you.

• What is the right configuration of the port for my Photosmart C6180 using 32-bit Windows 8?

  Hi all

  I have a HP Photosmart C6180. I recently changed to Windows 8 32-bit. I downloaded the HP Windows 8 drivers, but I still have problems with the printer. In Control Panel, the printer status says "error".  I think that it could possibly be a problem with the printer port settings. So, my question is, what is the right configuration of the port for my Photosmart C6180 using 32-bit Windows 8?

  I would greatly appreciate any help you can give me. Thanks, JoeRocket

  Hello JoeRocket,

  Welcome to the HP Forums!

  I understand that your Photosmart C6180 enjoys a status of "error". I will do my best to help you! I would start by following this entire document on "Printer is off-line" Message appears on the computer and the printer does not print.

  This document provides steps to check the printer driver and port of your computer. Please post your results, I'll be looking forward to hear from you.

  Have a good night!

• Hello my MacBook Pro model (MacBook Pro (15 inch, early 2011 am Dubai bought the Sryalsh C02FD2CPDF8 number and I am in Iran that MacBook Pro not enter the device screen when I turned on the pink vertical lines can be seen, the problem is restless))

  Hello my MacBook Pro model (MacBook Pro (15 inch, early 2011 am Dubai bought the Sryalsh C02FD2CPDF8 number and I am in Iran that MacBook Pro not enter the device screen when I turned on the pink vertical lines can be seen, the problem is agitated and it is not difficult to work with him because I like and what I should I do?))

  Serial number C02FD2CPDF8V