Pink/green line on the edge of the screen when the crossfade to and from black transitions

I've seen this posted as a known bug in first, but I have not found a decent solution for it.  Here's a screen Cap what it looks like:

Pink Line cap.jpg

Note the pink verticle line on the right side of the frame. It happens when I am exporting out of the timeline in a different format - it doesn't look like this in the timeline panel. I did some tests and it seems that do that when:

(A) it is fading to black or black - cross-dissolution of one video to another do not do

and

(B) the output video is 16:9 wide screen

This does not happen when I create a HD video and it happens when it's a video SD card in aspects "D1/DV NTSC (0.9091).

Thoughts?

I want to highlight a number of things here:

  • From my experience, I don't have a card CUDA, so I guess I use the Mercury playback engine. However, I always get a pink line using the Adobe Media Encoder. If I just export directly from first, I don't understand.
  • All my patterns are exported to 1280 x 720 or 856 x 480, which are divisible by 4.

Given these two points, I tend to say that the problem is with SOUL and must be resolved by Adobe. Use an opacity instead of transitions is all just silly - we used transitions in digital bouquets of editing for years, so it shouldn't cause pink pixels.

Tags: Premiere

Similar Questions

  • What is the green line in the address bar and how do I get rid of him?

    Not more happy with Firefox 5 that I was with Firefox 4, but I at least 1 new problem. There is an irritating, ugly green line that appears in the address bar. What is this and how do I get rid of him?

    The sounds that you have installed the extension of the State-4-Evar (Tools > Modules > Extensions).

    You can change the behavior of the progress bar in the extension Options.

    Status-4-Evar-> Options-> progress > [] see the progression in the address bar

  • Color LaserJet CP1525nw: 1 1/2 black lines on the right side and another black spot on the side right laserjet cp1525nw color

    I downloaded the software and latest drivers. It has the latest firmware. I contracted the toner and blown with compressed air. Look in the back for the dust from toner on the sleeve of teflon to fuser. Unplugged, restarted, of course my book has been for laser printers. Ran across several cleaning cycles, recalibrated color, put a piece of paper and toner open door when he was printing. Released A black to see if I could see and toner on blue cylinder. None of the things I've tried have solved the problem. Toner is about 3/4 down. It print fine with this new series of cartridges for quite a while.  I went from my warrarnty.

    .

    The amount of toner from the printer say that there is only an estimate. Your default seems to me that the black toner cartridge is bad. First thing I would do is to replace the black toner cartridge as it should solve your problem.

  • Dreamweaver - green line on the side of the MP4 videos, part 2

    The original discussion: Re: Dreamweaver - green line on the side of MP4 videos

    OK now I get disturbed (not the fault of you guys of course).

    I discovered that the green line is NOT on my videos, but is caused by the insertion of the video (via Insert-HTML-HTML5 video).

    Another method of insertion, the original route, I used in the old (Insert HTML plugin) version works better - does not cause the green line, but the line grey on the background remains.

    I don't want ALL the lines on the edges of my videos. (I like black open space, that I had, it's much more aesthetic and gives a full page less busy look).

    As you can see on other videos (approx) on the menu, what happened to the previous version of DW (defective if it was with El Capitan - it crashed or took a force - quit almost whenever I used it).   http://www.communicomics.com/eyemenu.html

    I am trying to edit these videos, and there seems to be no way to reintegrate those who are free to line to this new version.

    (This happens when I try to re - insert the same videos in this new version.) It is certainly something in this new version, which is the cause.)

    I am also changing the text, and apparently I can also no longer edit the text using the 'direct' either - the only way I found to do it is to make a code live/split screen and revise the text in the code section.

    I also miss the opportunity to make a convenient toggle of the widths of the table (I tried to create a new page, thinking that the green line can be caused by the table created in the previous version.

    (Maybe there is a simple way to edit live view that I'm missing?)

    But I'm trying to get this stuff finalized, and this new version is screwing things upward.

    I'll take the time to learn the Muse, but today, I need a quick way to work with what I have (and of course, when I do, there is no guarantee of Muse will not have the same question 'lines').

    I just want to be able to replace the videos with revision without the lines.

    If there is no work around for this, is it possible to have the old version of DW back so I can finish it without all this hassle?

    Please advise, my countdown has...

    Thanks again,

    Joe

    To get rid of the green line, make sure that your output video width is a multiple of 16.

    Short answer. With MPEG-2 and MPEG-4 (and other codecs DCT based), compression is applied to a grid of 16 x 16 pixel macroblocks. With MPEG - 4 Part 10 (h.264), multiple of 4 and 8 also works, but 16 is more effective.

    Nancy O.

  • Green line on the right side

    Hello

    When I export the media I get a green line on the right side, not always on the same sequence, it varies every time that I new export (when I change something on the sequences of integers), what would be the solution?

    346457.png

    solved the problem by cropping the image to 100% to 101% on images of 24 p

  • Annoying green line glisten under Compaq Cq40 LCD screen

    I don't know if it's because of the new BIOS I installed that caused it that I improved F.24 F.30 version and after that all of a sudden there's this green line boring glisten under my LCD... and my temp CPU reaches now to + 60 degrees Celsius, while before upgrading my CPU temp only amounts to 32 degrees Celsius.

    I already flashed the BIOS F.30 and now he's back to F.24 the temp went down, but the green line which sparkle under my LCD screen is still there... I checked the new updates to the graphics card but it says that it is up-to-date. so theBIOS has nothing to do with the flickering line after all I thought that it was caused by the high temperature. Haven't bought my laptop in Singapore in February this year no problem until this one

    BTW, my laptop is a Compaq CQ40 319TU with Vista Home Premium OS license.

    Message edited by amps on 12/05/2009 16:09

    @ Topz25 I brought to the HP service center, it's a hardware problem, they replaced the LCD screen and they didn't charge me a dime no problems yet so far

  • In Photoshop, how can I change the background (Mount table) from black to white. I must have hit something because it changed suddenly mid-project and I cannot find anywhere in preferences to solve this problem.

    In Photoshop, how can I change the background (Mount table) from black to white. I must have hit something because it changed suddenly mid-project and I cannot find anywhere in preferences to solve this problem.

    Right-click on the pasteboard, and you should have a choice of colours from timeline menu.

    I would add that you should have a file to open it or it won't work.

    Gene

  • The HP Omni100 5155 PC: HP omni100 5155 red and green lines on the screen

    I used a music cd in my pc one day and the next day I had thin green and red, vertical lines throughout the screen. I did a number of bugs, but the problem persists. I was wondering what I need to do or it sounds like a graphics card? Although I checked it and the message says: "the device is functioning properly."

    I tried the things:

    • updated drivers
    • scanned for viruses
    • cleaned the ram
    • memory diagnostic tool
    • update graphics card

    Sorry, for obvious reasons, I'm not here to sell you a computer.  Most of the all-in-one computer today have the specifications you are looking for, except perhaps the webcam integrated according to the model.  You can see the HP, Amazon or Tiger Direct store as examples.

    If you are looking to buy the same more or less the same model as you have now, they are abandoned or not available unless used or refurbished which I would not recommend it.

    Before doing something drastic, discover the repair costs to the one you have now.

  • HP Envy 5532 Printing green lines across the page when scanning in color

    Hi, I'm Green striped wallpaper is the best way to describe it, when I scan a document color the entire page has this striped background green and the image being analyzed. The printer is around the age of 18 months.

    I tried all the diagnostic tools that are available through the printer, nothing seems to clear it.

    Any suggestions?

    Hey @thelentons,

    Welcome to the HP forums! I hope you enjoy your stay here.

    I understand that your e-all-in-one printer of 5532 Envy is scanning with green lines. I can help you with that.

    To start, make sure that the printer is plugged directly into a wall outlet , not a surge protector. Once it's done remove any paper flat from the printer and turn the printer off, then on again. Finally we will try to make a copy. If the copy has lines so you have a hardware problem. If you are able to make a copy without lines so you can have a software problem.

    If you have a hardware problem

    While the printer is turned on remove the cable at the back of the printer for a minute, turn on the printer and try to make a copy.

    If the copy always has lines in it then we will make a factory reset the printer. I'll send you some pointers on how to do so shortly in a private message.

    If after the reset you still have lines in print then the printer needs to be replaced. You can contact HP support by clicking here and filling out the form below.

    If you have a software problem

    I can provide you with more information, but I need to know what operating system is on your computer. If you are not sure what your operating system is you can click here to find. Please let me know what you use, and I'll be better able to help you.

    I hope this solves your problem of copy and wish you a nice day!

    If this solves your problem then please help others to find this post by clicking on accept as Solution on my post.

    If you appreciate my help so please let others know by clicking on the icon below my post thumbs up.

  • Red/green line at the beginning and at the end of the rendered video

    Hi, I recently started to use the first and it's amazing, but every time I make a video; a green line which then became Red appears at the beginning of the video, and it is quite visible because I usually begins with a Fade In-Out effect. It is the same for the end of the video, but I do not understand why this is happening.

    Here's my info:

    Operating system Windows 10

    NVidia GeForce GT 720MGraphic map

    8 GB RAM

    Intel Core i5-3337U CPU @ 1.80 GHz

    Adobe Premiere Pro CS6

    Any third party Plugins installed

    Gameplay videos, H.264 codec.

    The only time you won't see a coloured line is when a clip freshly abandoned in the calendar that has a codec/format supported.

    What gamefootage probably didn't.

    And probably don't have material on MPE.

    In your case there always will be so a line colored over your footage.

  • Dreamweaver - green line on the side of MP4 videos

    I am a Mac user, and because Quicktime movies are now obsolete, I am trying to replace them on my web pages with videos MP4.  But when I do, a junk to the right green line (and a grey one less intrusive on the background) appears when I joined an MP4.  I can not make disappear - tried to carve out a few pixels, etc...
    Here's what it looks like (both within the program and on the web): GREEN LINE

    Adobe Media Encoder can convert to MP4.

    Nancy O.

  • Green lines on the canvas?

    How do I get the green lines? BTW, I pressed "CTRL r" and then pressed the numbers!Capture.PNG

    These lines are the guides - they can be moved off the screen by selecting the tool move, then dragging them to the canvas.

    If you can not select them, they can be locked - to unlock, go to view > Lock Guides and make sure that 'Lock Guides' is disabled.

    You can also erase all your Web guides by going to view > clear Guides.

    See you soon!

    Kendall

  • Pink vertical lines in the scanned Document

    We have a Dell 2335dn Printer Laser multifunction, under intensive use for about 2.5 years out of warranty. From today, digitization has roses vertical lines, using the glass plate or ADF, scan to PDF format or image regardless.

    Any thoughts on what we can do to remove the lines? Printing is fine.

    The printer/scanner was overheating. We turned off for 20 minutes to cool and scan resumed normally. We ordered the users to use a different printer for secondary purposes in order to avoid the excessive use of the machine.

  • V10.2 has 2 of the same clip hit the other with a green line in the middle. Help!

    Hello

    My flash drive was working fine then all of a sudden on any browser, I tried Google Chrome, IE, Firefox and Opera, he plays the clip but has 2 of the same clip crushed on the other (so that you try to watch a movie on a 4:3 ratio 16:9 aspect ratio) & he has a brilliant green stripe between the 2 collars to... I tried to uninstall and reinstall but it still it! It does on any website I tried to watch the clips on & it's driving crazy me!

    PLEASE HELP IF YOU CAN, I WILL BE ETERNALLY GRATEFUL!

    First thing to try: disable hardware acceleration (Flash Player settings).

    If this does not resolve the problem, provide more information, i.e. your OS & version.

  • Compare lines with the contractor ID and choose the line with Min Date rental

    Hello

    I have a scenario where I need a line with the Minimum of the Pavilion main 'p' Hire Date whenever there are multiple records with the same ID of the contractor. I need a SQL for this

    For example

    Contractor_ID name Hire_Date end_date Primary_Flag

    123 Tom 9/11/2011-9/11/2012

    123 Tom 9/12/2012-5/12/2012


    I need to score the first line of 'P '. It is an example where there are thousands of discs where I have to mark. Some cases it can be 3 or 4 files to contractor_id even where I need a 'P' flag for recording with Min Hire_Date


    Thank you
    RAM

    Hello

    If you want to ensure that only 1 row by entrepreneur is marked "P", if the lines are the same, then I suggest you do something on the ROW_NUMBER analytic function, like this:

    SELECT       contractor_number
    ,       full_name
    ,       job_title
    ,       hire_date
    ,       end_date
    ,       CASE
               WHEN  1 = ROW_NUMBER () OVER ( PARTITION BY  contractor_number
                                                    ORDER BY          hire_date
                                  ,                end_date     DESC
                                )
               THEN  'P'
           END          AS primary_flag
    FROM       contractor
    ORDER BY  contractor_number
    ,            hire_date
    ,       end_date
    ;
    

    Output:

    CONTRACTOR
       _NUMBER FULL_NAME  JOB_TITLE  HIRE_DATE  END_DATE   P
    ---------- ---------- ---------- ---------- ---------- -
       1862180 Tom        Developer  8/01/2011  11/30/2012 P
       1862180 Tom        Developer  12/01/2012 11/30/2013
       1862181 Sam        Developer  9/01/2012  9/30/2012
       1862181 Sam        Developer  9/01/2012  12/30/2012
       1862181 Sam        Developer  9/01/2012  12/30/2012 P
    

Maybe you are looking for

  • Disappear several buttons to create the message window after installing Enigmail and GNUpg

    Hello. I decided to install the Thunderbird PGP module (Enigmail). During the installation, it was necessary to install additional software GnuPG. After restart Thunderbird in create message windows several buttons disappear as: fonts, links, etc. (s

  • Satellite L - water damage and the laptop does not light

    Hello I don't know if this is the right forum for this, but I was just wondering if someone could give me some advice. My brother spilled some water on my laptop 3 days ago (argh!). He immediately turned off and won't start up again. I stamped it tow

  • audio 7.1

    Does anyone know all the movies with audio 7.1

  • Cannot access wireless internet.

    original title: have five bars on my connection Wireless in the toolbar with a yellow triangle on it... can not access internet... can you help me?   have already unplugged the modem.  What can I do else?  Thank you. having five bars on my connection

  • Install Windows Live Essentials 2011

    To install Windows Live Essentials 2011, he said I have to remove Windows Live. After that, he said I need for Vista SP2 which I use. After that, the page of Windows Live Essentials 20121 did not download it because I needed the download platform usi