PIX 501 reset help

Similar Questions

• Reseting ipsec on PIX 501

  Hi all. Just a quick question. I can't seem to find how to reset ipsec on PIX 501 and force her to negotiate again and I also want to reset statistics for ipsec his. I know that I saw somewhere, orders, but now can't seem to find the commands from anywhere.

  Thanks in advance for any help.

  Hello...

  Config mode...

  ISAKMP crypto claire his

  - and -

  clear crypto ipsec his

  PS. You can find the commands on the PIX by entering the configuration mode by typing...

  PIX01 (config) # clear cry?

  Hope the above helps and please note messages!

• Help with vpn pix 501

  I'm setting up a cisco pix 501 vpn tunnel but will have questions. The Firewall works although I am able to get out of the internet, but the VPN does not work. On the primary side, I see that the tunnel is up and the traffic is sent but not received.

  Currently I'm sitting at the secondary location but don't know what the problem maybe. Anyone know what I have wrong which could prevent the data to send from this device?

  Here is my config

  Here's my config if it would help

  See the race
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 2KFQnbNIdI.2KYOU encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  hostname ciscofirewall
  domain hillsanddales.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 5
  fixup protocol rtsp 55
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25

  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list 101 permit ip 192.168.80.0 255.255.255.0 192.168.50.0 255.255.255.0
  192.168.80.0 IP Access-list sheep 255.255.255.0 allow 192.168.50.0 255.255.255.0
  in_outside list access permit tcp any host 192.168.50.240
  in_outside list access permit tcp any host 64.90.xxx.xx
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside 66.84.xxx.xx 255.255.255.252
  IP address inside 192.168.80.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  location of PDM 192.168.50.0 255.255.255.0 outside
  location of PDM 192.168.80.2 255.255.255.255 inside
  location of PDM 192.168.50.0 255.255.255.0 inside
  location of PDM 182.168.80.0 255.255.255.255 inside
  location of PDM 0.0.0.0 255.255.255.0 inside
  location of PDM 0.0.0.0 255.255.255.255 inside
  location of PDM 192.168.80.5 255.255.255.255 inside
  location of PDM 192.168.80.7 255.255.255.255 inside
  PDM logging 100 information
  history of PDM activate

  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 66.84.xxx.x
  Route inside 192.168.50.0 255.255.255.0 192.168.50.240 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.80.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  <--- more="" ---="">

  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp-3des esp-md5-hmac aptset
  aptmap 10 ipsec-isakmp crypto map
  correspondence address card crypto aptmap 10 101
  card crypto aptmap 10 peers set 64.90.xxx.xx
  card crypto aptmap 10 transform-set aptset
  aptmap interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 64.90.xxx.xx netmask 255.255.255.255
  ISAKMP identity address
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 md5 hash
  10 2 ISAKMP policy group
  ISAKMP life duration strategy 10 86400
  Telnet 192.168.80.2 255.255.255.255 inside
  Telnet 182.168.80.0 255.255.255.255 inside
  Telnet 192.168.80.5 255.255.255.255 inside
  Telnet 192.168.80.0 255.255.255.0 inside
  Telnet 192.168.80.7 255.255.255.255 inside
  Telnet timeout 5
  SSH timeout 5
  management-access inside

  Console timeout 0
  dhcpd address 192.168.80.2 - 192.168.80.33 inside
  dhcpd dns 64.90.xxx.xx 64.90.xxx.xx
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:01532689fac9491fae8f86e91e2bd4c0
  : end

  Hello

  At least the NAT0 ACL is not in use

  You should have this added to the configuration

  NAT (inside) 0 access-list sheep

  -Jouni

• Help the PIX 501 - cannot access startup.html

  I'm new to the network and has received a job to configure the PIX 501 firewall.

  The fact is:

  We use IP table rules as a firewall on a linux machine. My pc is connected to a switch. So I use the yellow network cable to connect the port of the Pix 501 0 to the port in the switch. Then I disconnect my pc of swich cable and plug into the port of the Pix 501 1.

  My pc is to use a static ip address before. I try to change to automatically get an IP address, but it will not work. So I changed the setting and use the IP address originally. Pop up message network connection icon says that the local connection is enabled. But when I try to ping 192.168.1.1, request time-out. Also I can't acess the https://192.168.1.1/startup.html.

  I have a look at Books Online cisco and shootings of disorder, but most of them talk about the configuration or more advance features. I'm still on the very basic level to try to connect to the firewall.

  I hope someone can help me. All ideas and questions are welcome. Thank you.

  Your IP address should be fine. You do not want to have the PIX connected to your local network, even if you have the Linux firewall as well as this will cause a conflict. Keep the PIX the LAN for now. Your DNS configuration will have no effect because the url you are trying to reach is based on the IP address and not the domain name if your PC has nothing to look for.

  You have to check the cable that you use - if your PIX has only an 'inside' interface, then you must use a crossover cable. If he has four so it's built in switch for a straight cable will be fine. Is what PIX model?

  After checking the cable - see if you can console in the firewall - use the blue cable that came with the PIX and set up a connection (hyper terminal) terminal with the help of 9600, 8, no 1. If you can console and then you can stick in a basic configuration you can get.

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• Adding a pix 501 VPN 2

  Hello.. I am beginner in this kind of things cisco...

  I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...

  Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:

  Outside_map map (ERR) crypto set peer 200.20.10.3

  WARNING: This encryption card is incomplete

  To remedy the situation even and a list of valid to add this encryption card

  Hi garcia

  for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...

  for configuration, you can go through the URL below... It has all the details on IPSEC config:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• Microsoft secondary authority w / Cisco router / PIX 501

  I'm trying to get digital certificates to work on my 2621XM router. I have also

  need to put in place on the three firewalls PIX 501 but who have not obtained until now still. I have

  don't have no access to the CA root, but it could bring in line if I had to. I have

  have a stand-alone Microsoft subordinate CA that I want to use to publish all

  certificates.

  Is it possible, as well with the router and the firewall? If so, what version

  the IOS do I need? I installed the add-on CEP at HQ. I can't

  It works and I'm starting to wonder if it is still possible. If this doesn't

  work, how can I make it work? I have all the documents that Cisco has combed

  on the subject and have gotten nowhere.

  Any help would be greatly appreciated. Thank you.

  Jennnette,

  I sent this document, let me know how it goes or if you have any questions.

  Kurtis Durrett

• Configure the PIX 501 for IDS

  I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

  IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

  If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

  You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

• VPN with PIX 501

  Help!

  I'm trying to set up VPN on my PIX 501. I have no experience of the PIX and have no idea where to start!

  Any help will be greatly appreciated.

  Thank you

  Bennie

  access list allow accord a

  where is the name of the access list that you applied the entrants to your external interface. You may also allow accord coming out, if you have a list of incoming configured access to your inside interface.

• PAT on IPSEC VPN (Pix 501)

  Hello

  I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.

  I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.

  lines of current config interesting configuration with static mapping:

  --------------------------------------------------------------------------

  access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0

  access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host

  access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z

  IP address outside w.w.w.1 255.255.255.248

  IP address inside 10.0.0.1 255.255.255.0

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0

  Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1

  correspondence address card crypto mymap 10 103

  mymap outside crypto map interface

  ISAKMP allows outside

  Thank you!

  Dave

  Dave,

  (1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent

  translation for your guests inside and they will always be this way natted. Use

  NAT of politics, on the contrary, as shown here:

  not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0

  Global (outside) 2 z.z.z.z netmask 255.255.255.255

  (Inside) NAT 2-list of access 101

  (2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."

  Delete this because you need to nat 2 nat/global card. (as a general rule, simply you

  If you terminate VPN clients on your device and do not want inside the traffic which

  is intended for the vpn clients to be natted on the external interface).

  (3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first

  translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which

  sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.

  I hope this helps. I have this work on many tunnels as you describe.

  Jamison

• Unable to connect to PDM on PIX 501

  just cannot understand this. I have a PIX 501 I used to connect very well. Now I can't get the PDM to come up inside, outside, nothing.  I use the same (old) of JAVA 1.4 version I always used. I can Telnet etc... Very well. The HTTP server is enabled and have granted access from my IP address. Any help would be greatly appreciated. See my config below.

  See the pixfirewall # running
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry2YjIyt7RRXU24 encrypted password
  passwd encrypted XXXXXXXX
  pixfirewall hostname
  domain ciscopix.com
  clock timezone IS - 5
  clock to summer time EDT recurring
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 X 0
  fixup protocol h323 ras X 18 - X 19
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  name admin_subnet X.X.X.X
  inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow admin_
  subnet 255.255.0.0
  inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow X.X
  . X.X 255.255.255.0
  outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list permit admin_subn
  and 255.255.0.0
  outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list allow X.X.X
  . X 255.255.255.0
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP outside X.X.X.X 255.255.255.128
  inside X.X.X.X 255.255.255.0 IP address
  alarm action IP verification of information
  alarm action attack IP audit
  PDM location admin_subnet 255.255.0.0 outside
  location of PDM X.X.X.X 255.255.255.0 inside
  PDM location x.x.x.x 255.255.255.255 outside
  location of PDM X.X.X.X 255.255.255.0 outside
  location of PDM X.X.X.X 255.255.255.255 outside
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  AAA authentication enable LOCAL console
  AAA authentication http LOCAL console
  LOCAL AAA authentication serial console
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  Enable http server
  http X.X.X.X 255.255.255.0 inside
  http admin_subnet 255.255.0.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  outside_map 20 ipsec-isakmp crypto map
  card crypto outside_map 20 match address outside_cryptomap_20
  card crypto outside_map pfs set 20 group2
  card crypto outside_map 20 game peers X.X.X.X
  outside_map crypto 20 card value transform-set ESP-AES-256-SHA
  outside_map interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address X.X.X.X 255.255.255.255 netmask No.-xauth non - co
  Nfig-mode
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 aes-256 encryption
  ISAKMP policy 20 chopping sha
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 8 X 00
  Telnet X.X.X.X 255.255.255.0 outside
  Telnet X.X.X.X 255.255.255.0 inside
  Telnet admin_subnet 255.255.0.0 inside
  Telnet timeout 30
  ssh X.X.X.X 255.255.255.255 outside
  X.X.X.X 255.255.255.0 inside SSH
  SSH timeout 30
  management-access inside
  Console timeout 30
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  username password XXXXXX XXXXXXXXXXX encrypted privilege 15
  Terminal width 80
  Cryptochecksum:
  : end

  Hello Mark,

  lol Nice to know that everything works fine now

  Don't forget to mark it as answered and to classify the useful messages (if you don't know how to evaluate a message just to get to the bottom of each answer and mark 1 being a wrong answer, being a great answer 5 stars)

  Kind regards

  Julio

  PD: Some kudos for you (because of the answer)

• L2l IPSec VPN 3000 and PIX 501

  Hello

  I have a remote site that has a broadband internet connection and uses a PIX 501.  We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

  I followed the following documentation:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

  However the L2L session does not appear on the hub when I check the active sessions.

  The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

  Any help or advice are appreciated.

  I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

  For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

  Here is an example of sample config

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

  I hope this helps!

• On PIX 501 6.3 intermittent Internet access (5)

  Hello

  I have a problem of access to the Internet from the local network behind a PIX 501. It worked for months, but suddenly, I discovered that Internet access is intermittent. Internet access works for about 10-15 minutes and then goes down. When I reboot the firewall or disable ARP Internet works again. I turn on debugging with 'debug arp' and I get an error message "arp-in: Dropping request outside the unsolicited nonadjacent ROUTEOUTSIDE 0002.cf69.50cf for 82.x.137.x 0000.0000.0000»

  Any ideas on what could be the problem?

  Thank you for your help.

  Kind regards.

  Hello, Couple of things to check.

  You have ICMP permitted on the external interface of the PIX. If so, can ask you someone to ping from the internet to the external IP address.

  When they ping, can you unplug the external interface and see if they receive a response in return.

  If so, then there is a problem with the access provider. They could give your IP address to another person.

  If this isn't the issue, then you open a TAC case and resolve this problem.

  See you soon,.

  Gilbert

  The rate of this post, if that helps.

• Pix 501 connection problems

  I am very new to cisco equipment and I was wondering if someone could help me with this (probably very simple question).

  When connecting to my pix via the browser (https://192.168.1.1/startup.html), the browser never took the start screen with the message that says "loading, please wait." This leads me to believe that the firewall is rejecting connections from my machine (which uses dhcp to get an ip address of the pix).

  To work around this problem, I tried to connect to the CLI using hyperterminal. I can connect and run a few basic commands as 'show version', but cannot log on as a user with permissions.

  If the web interface has a default connection of void & empty, surely the cli should be the same?

  Is anyone able to tell me what is the default login, so that I can start confguring the pix via the cli?

  Thanks in advance.

  Justin Spencer.

  Please see below for info pix:

  Cisco PIX Firewall Version 6.3 (3)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday, August 13 03 13:55 by Manu

  pixfirewall until 12 minutes 18 seconds

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 0011.937e.0486, irq 9

  1: ethernet1: the address is 0011.937e.0487, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  The maximum physical Interfaces: 2

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal guests: 10

  Throughput: unlimited

  Peer IKE: 10

  This PIX has a restricted license (R).

  Serial number: 808301473 (0x302db3a1)

  Activation key running: 0xb53be54d 0x26da18f9 0xb2b78cef 0x8fe1abb6

  Configuration changed from enable_1 to 15:36:42.554 UTC, Monday, November 8, 2004

  pixfirewall >

  long live java.

  Please this mark as resolved, others won't waste time.

  Thank you

• PIX 501 no connectivity to wide band

  Hey,.

  Just got a pix 501 to put in the office, the problem is, I went through the automatic configuration wizerd and looked in the settings, online, that I can't seem to see dchp outgoing connetion. Is there a setting Im missing. When I hit so he could refresh ip he tells me he cant and frankly Im lost I have a N + so I some knowlage of the installer, but it seems to be difficult to find info on this box anyone help or point me in the right direction on how to get online connectivity.

  thamk you for your time

  William,

  That mark it as resolved!

  This is your post not mine.

  ;-)