PIX 515 - several subnets
Can I have a 28 and one allocated 24 times in a PIX 515e? My current setup is configured for the 28 and I would like to keep this address space, just as it is and then add the 24 if possbile.
Thank you!
Hello
I think that the solution is easier than you think. You can use your new address range with nat, global and static without actually set it up on the physical interface. In this way, you can use your new address space. Your ISP should route your new network to your PIX outside interface. That's all.
Best regards
Robert Maras
Tags: Cisco Security
Similar Questions
-
Hello
We have some difficulty in moving traffic in and out of a Cisco PIx 515 firewall. We use it with two demilitarized. The first DMZ has a mail in her Server (before end mail server) that communicates with a different mail server (back end mail server) inside, it is called DMZ1. The second DMZ (DMZ2) has some users who are expected to pass through the firewall to the outside and use the internet and must have access to the e-mail DMZ1 server. Inside users must be able to use the Internet and can access DMZ1. Here's the important part of our Setup.
What we were doing, we can correctly access from inside, inside users to access internet permit to join the DMZ1 e-mail server and the mail in DMZ1 server the inside. Our problem is that we are unable to browse the internet on the DMZ1 Messaging server if we put DMZ1 as gateway ip address on that server and the address ip of the DNS of the ISP is propely located on the same machine. Also, we could not do DMZ2 users browse the internet, although we allowed the www Protocol in the fromOut access list. One last question, can we do the DMZ2 a DHCP server on the interface on the PIX and do distribute ip addresses to users on that subnet only? Thanks for any help in advance.
6.3 (3) version PIX
interface ethernet0 car
Auto interface ethernet1
Auto interface ethernet2
Auto ethernet3 interface
!
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif ethernet2 dmz1 security50
nameif ethernet3 dmz2 security40
!
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
!
names of
!
IP outside X.Y.Z.163 255.255.255.248
IP address inside 192.168.0.9 255.255.255.0
dmz1 192.168.10.1 IP address 255.255.255.0
IP address dmz2 192.168.20.1 255.255.255.0
!
fromOut list of access permit icmp any host X.Y.Z.162 source-quench
fromOut list of access permit icmp any host X.Y.Z.162 echo-reply
fromOut list of access permit icmp any unreachable host X.Y.Z.162
fromOut list of access permit icmp any host X.Y.Z.162 time limit
fromOut list access permit tcp any host X.Y.Z.162 EQ field
fromOut list access permit tcp any host X.Y.Z.162 eq telnet
fromOut list access permit tcp any host X.Y.Z.162 eq smtp
fromOut list access permit tcp any host X.Y.Z.162 eq www
!
fromDMZ1 list of access permit tcp host 192.168.10.2 192.168.0.0 255.255.255.0
fromDMZ1 list of allowed access host ip 192.168.10.2 192.168.0.0 255.255.255.0
!
fromDMZ2 list of access allowed tcp 192.168.20.0 255.255.255.0 192.168.10.0 255.255.255.0
!
pager lines 24
!
Outside 1500 MTU
Within 1500 MTU
dmz1 MTU 1500
dmz2 MTU 1500
!
Global (outside) 1 X.Y.Z.164 netmask 255.255.255.248
Global (outside) 2 X.Y.Z.165 netmask 255.255.255.248
NAT (inside) 1 192.168.0.0 255.255.255.0 0 0
NAT (dmz1) 1 192.168.10.2 255.255.255.255 0 0
NAT (dmz2) 2 192.168.20.0 255.255.255.0 0 0
static (inside, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0
static (dmz2, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0
static (dmz1, external) X.Y.Z.162 192.168.10.2 netmask 255.255.255.255 0 0
!
Access-group fromOut in interface outside
Access-group fromDMZ1 in interface dmz1
Access-group fromDMZ2 in the dmz2 interface
Route outside 0.0.0.0 0.0.0.0 X.Y.Z.161 1
Hi jamil,.
There is a sentence on the URL I sent you, you can now activate dhcp option within the interface. Just check this...
REDA
-
PIX-515E-R-BUN MEM upgrade with PIX-515-MEM-32
Hi all
is it maybe possible to upgrade the PIX 515E - r
with this release of PIX-515-MEM-32, without having to pay
for all PIX-525-SW-R-UR = update license.
Concerning
Richard
The PIX will recognize this new memory but the configuration is not supported. The upgrade of UR's memory, but also an update of license for several interfaces, failover, etc... Unless you want to add these features to your PIX, it is not necessary to upgrade memory. 32 MB is more than enough for a PIX 515R.
Does that help?
Scott
-
Good day to all,
I'm trying to configure the client VPN to a PIX 515. Once VPN'ed in, the traffic is going no where, but on THIS subnet. The Vlan that we are trying to achieve is a 10.111.250.x/23. Once VPN'ed in the allocation of an IP address is 10.111.250.33 - 10.111.250.63. We can VPN in and get VPN IP assigned, but we cannot get anywhere inside VLANs. I was sure that it could be done in a layer 2. You can view the assigned addresses VPN arped entries and the inside address Vlan on the Pix.
Keep in mind, my first thought was to change the VPN address assigned, but we do not want to carry on this Vlan especially because access is very limited.
Is it possible to make this work? If I have to redo attributes and policy, I.
Thank you
Dwane
The output shows that the PIX is decrypt packets, but not encryption.
So there is a good chance that packets are sent within the network but not to return.
Check the following:
management-access within the--> this command should allow ping to the IP of the VPN PIX inside (make sure you that if you can TEST this IP address when connected)
Verify that the default gateway within the network (behind the PIX) is the current inside the property intellectual of the PIX.
After these tests, post again "sh cry ips its"
Federico.
-
MM, pix 515 and mac filtering
I have an application called MeetingMaker, located at the back of my pix 515 that is used off site by 5 users. Since accessing this program on the internet, and users can have dynamic addresses, it is possible to filter by mac address somehow to allow access through the firewall to the app? Thank you.
MAC addresses not browse the limits of layer 3. In others, your MAC address of clients cannot be seen or known once the traffic passes through the default router for that subnet. So the answer to your question is 'no '.
You can use AAA to handle this. How your clients connect to the server? (port/application)? If its HTTP/S, the Pix can check this name of user and password before allowing access. If it is a part on request/port, you can still use authentication by requiring them to connect to the web server out there first. This will cause the Pix to authenticate by using the challenge of browser, and the Pix can be configured to allow connections to the hosts authentiated.
-
PDM with PIX 515 does not work
I just upgraded our PIX 515 of 6.1 to 6.2. I also added support FOR and loaded the version 2.1 of the PDM. I am trying to browse the MDP, but I can't. What Miss me?
Hello
have you added the following lines to your config file and have you used HTTPS to access the pix (http is not taken in charge, only https)?
Enable http server
http A.B.C.D 255.255.255.255 inside
A.B.C.D is the ip address of the host from which you are trying to reach the pix with the pdm.
If you're still having problems after the addition of these two lines, you might have a look at this page:
http://www.Cisco.com/warp/customer/110/pdm_http404.shtml
Kind regards
Tom
-
PIX 515 and software version 6.3 (4)
We have a PIX 515 (not 515E). Currently, we are running software version 6.2 (2). I was wondering if we can improve the software to version 6.3 (3) or 6.3 (4), or do we need to replace the hardware with PIX 515E?
Also what should I do on my current PDM version 2.0 (2) if it is possible to upgrade the PIX to a 6.3 version?
Thank you.
You can run on the Pix515 6.34. It takes at least 16 MB of flash and 32 MB of RAM.
If you use PDM, you will need to be updated also.
Josh
-
Limit the number of users for a pix 515 uauth
I have a PIX 515 authenticate and authorize against a Cisco Secure ACS server for outbound internet connections (using the web prompt). For the purposes of scale, I need to know the maximum number of sessions competitor for these types of users. I know there is a limit of 16 reviews on simultaneous approval process (the process of logging in first), but once they are connected, is there a limit?
Once connected, the number of connections is limited by the number of concurrent connections that can handle a PIX. For example, the PIX 515 E can handle a maximum of 130 000 concurrent connections.
-
Hi all
Here's my problem, I have 2 PIX 515 firewall...
I'm trying to implement a VPN site-to site between 2 of our websites...
Two of these firewalls currently run another site to site VPN so I know who works...
I can't do the second site to the site to launch the VPN... when looking on the syslogs I get refused packages...
Protected networks are:
172.16.48.0/24 and 172.16.4.0/22
If I try to ping from the Cisco (172.16.48.4) to 172.16.4.5, I get the following syslog:
2 sep 02 2008 08:59:47 106001 172.16.48.4 172.16.4.5 incoming TCP connection doesn't deny from 172.16.48.4/1231 to 172.16.4.5/135 SYN flags on the interface inside
It seems that the tunnel is trying to initiate, but something is blocking the internal traffic to penetrate through the VPN.
Don't know what that might be, the other VPN are working properly.
Any help would be great...
I enclose a copy of one of the configs...
Let me know if you need another...
no road inside 172.16.4.0 255.255.252.0 172.16.48.1 1
Remove this path should you get. Please rate if it does. Similarly, if you have a road similar to the other end, it should be deleted as well.
-
PIX - 515 does not identify Tokenring Interfacecard
Hello
I installed a PIX-1 TR interface in the PIX 515. Start ok, 'answer' no configuration. SH LVE and sho int etc. presents only the build Ethernet0 and Eth1 but no interface tokenring.
HS release looks like as follows.
Thanks Ruedi
pixfirewall # sh ver
Cisco PIX Firewall Version 6.2 (2)
Cisco PIX Device Manager Version 2.0 (2)
Updated Saturday, June 7 02 17:49 by Manu
pixfirewall until 10 mins dry 14
Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor
I28F640J5 @ 0 x 300 Flash, 16 MB
BIOS Flash AT29C257 @ 0xfffd8000, 32 KB
0: ethernet0: the address is 0003.6bf6.a8a9, irq 11
1: ethernet1: the address is 0003.6bf6.a8aa, irq 10
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES: disabled
Maximum Interfaces: 3
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: unlimited
Throughput: unlimited
Peer IKE: unlimited
Serial number: 405341167 (0x182903ef)
Activation key running: xxxxxxxxx
Modified configuration of enable_15 to 13:11:47.490 UTC Tuesday, December 23, 2003
pixfirewall #.
Hello
Token-Ring is no longer supported, I think since version 6.0.
-
termination of VPN client 4.0 on pix 515
I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.
Journal of VPN client:
Cisco Systems VPN Client Version 4.0 (Rel)
Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.
Customer type: Windows, Windows NT
Running: 5.0.2195
1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002
Start the login process
2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001
Microsoft's IPSec Policy Agent service stopped successfully
3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004
Establish a connection using Ethernet
4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "x.x.x.226".
5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B
Attempts to establish a connection with x.x.x.226.
6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226
7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017
Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A
IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014
Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.
18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025
Initializing CVPNDrv
19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001
Signal received IKE to complete the VPN connection
20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001
Service Microsoft's IPSec Policy Agent started successfully
21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
Journal of Pix:
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP
RS: 1
Exchange OAK_AG
ISAKMP (0): treatment ITS payload. Message ID = 0
ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1
ISAKMP: 3DES-CBC encryption
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP
RS: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP
RS: 1
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP
RS: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP
RS: 1
ISAKMP (0): retransmission of phase 1...
ISAKMP (0): retransmission of phase 1...
ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226
ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP
RS: 1
Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0
ISAKMP: Remove the peer node for x.x.x.194
Thanks for any help
Hello
Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...
http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757
This link will show you IKE proposals be configured on the PIX (VPN server)
Arthur
-
Hi all
My company needs upgrade its PIX 515 to have the function VPN 3DES for remote site connection. So I just need to buy a license of 3DES for the PIX functionality? and can I also upgrade the IOS 6.1 so that I can use PDM to config the PIX? And I also need to upgrade the memory in the PIX?
Thank you very much!
Best regards
Teru Lei
Yes to the first question.
Better 6.2 and pdm 2.1 I think.
How much memory do you have? Reach
There is memory for pix 6.2 requirements
Good luck!
--
Alexis Fidalgo
Systems engineer
AT & T Argentina
-
How to open a port and limit the range of addresses that use it on PIX 515?
I have a Pix 515 v6.3 and a new piece of software that I'm getting soon need aura 5080 open port for incoming & outgoing HTTP traffic. The server will be in my DMZ to 10.0.0.1
I would like to restrict inbound access to this port so that it can be used in 4 specific IP adderess foreign xxx.xxx.xxx.24 through xxx.xxx.xxx.27 and also, if possible, limit the outbound destination using this port to a single specific foreign IP address xxx.xxx.xxx.30.
Could you please tell me the best way to do it.
Thank you in advance for a relative novice to PIX.
PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.24 host MyWWWPublicIP eq 5080
PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.25 host MyWWWPublicIP eq 5080
PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.26 host 5080
PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.27 host 5080
PIX (config) # access - group acl-outside in interface outside
PIX (config) # access list acl - dmx permit tcp host 10.0.0.1 xxx.xxx.xxx.30 eq 5080
PIX (config) # access - group acl - dmz dmz interface
static (inside, outside) MyWWWPublicIP 10.0.0.1 netmask 255.255.255.255 0 0
See also:
PIX 500 series firewall
http://www.Cisco.com/pcgi-bin/support/browse/psp_view.pl?p=hardware:PIX & s = Software_Configuration
Configuration of the PIX Firewall with access to the Mail Server on the DMZ network
sincerely
Patrick
-
A question about the old Pix 515
Hi Experts.
My client needs additional interfaces of FE and do not want to migrate the chassis 515E.
Can the data sheet of the former 515 Pix no longer available due to the declaration of the EOS, you please confirm that the Pix 515 supports 1FE - PIX and PIX - 4FE cards before ordering one of them?
Thank you
The 515 supports 4 interface cards. Make sure they are running a UR pix license if - 515R takes only supported 3 interfaces.
-
DNS traffic blocked after PAT - PIX 515
I have PIX 515 with 3 named NIC (internal, external, dmz)
I have 2 servers (Exchange and Windows 2000 with SMTP) in the demilitarized zone.
I currently have a static command pointing to doamin for exchange Server IP address in the DMZ.
I wanted to PAT on the IP address of the e-mail domain so that the configuration will look like as follows.
The IP field will be used for the global IP
all pop3 for global ip traffic will go to Exchange
all www for the global IP traffic will go to Exchange
all smtp for global ip traffic will go to the Windows 2000-based SMTP relay (SMTP relay is configured to send the e-mail received in exchange Server)
I hosted DNS udp and tcp traffic to the servers.
before pat, the server can use DNS to resolve IP domain e-mail and send mail to the Internet.
As soon as I PAT the Internet e-mail delivery stops.
When I did an NSLOOKUP command returns an error indicating that the DNS server cannot be resloved.
The servere DNS used by these 2 servers are servers DNS of ISP.
Is there any concern when you PAT.
Thank you
Hello
I found the problem:
for now, your dmz servers can go to the internet with pop3, smtp, and www. Only for these protocols is a (static) translation to provide in the config file.
You will need to will provide you a translation for other protocols (for example, dns) also. This can be accomplished with one of the following two things:
create a nat - pair overall for the DMZ for outdoor
NAT (dmz) 1 0.0.0.0 0.0.0.0
Global (outside) 1 200.100.100.168 (already exists)
create a static translation for each of the other protocols (next to pop3, smtp, www), you want to pass from the dmz to the internet (you already did that for www, pop3 and smtp).
Kind regards
Tom
Maybe you are looking for
-
How can I configure Messenger to Facebook messages?
Sorry, I can't find any which section for Messenger app on this site, so I had picked a spot at random for this post. I followed the instructions on this site, but it does not work.http://osxdaily.com/2015/04/25/set-Facebook-Messenger-Mac-messages-OS
-
system off: Pavilion dm4-1173cl laptop '69112228 off system '.
Machine: HP Pavilion dm - 4 cl of 1173 Problem: 'SYSTEM OFF 69112228 '. 1.) had password on boot enabled. 2.) on the startup, received message to enter the startup password ('enter the password administrator or power on password') 3.) took 3 tries (k
-
Keyboard HP Envy 17 spits out several key with a simple pressure on
Have a problem with the keyboard on the HP Envy 17. There are three keys which, for some reason, has stopped working. The 'o' key product zero, key, left the House, period, 'o' and 'p '. The "L" produced three key, period, PG., six, 'l' and semi cole
-
Wandering SQL Native Client Datasource - apparently, it's a pretty common problem and I see several resolutions to it. This problem started for our long company until I started working here. We do not allow remote connections. JDE Enterprise Serve
-
Windows 7 Ultimate 32-bit shows that it is not authentic
Hey guys, well I have a problem I have win 7 ultimate x 84 32 bits and its copy but I can't get this thing off my windows is not genuine. Please don't suggest a windows loader because it does not work I have a product key that I receive, but no guy a