Portege 7140CT Shutting Down in Standby Mode - cannot close normally

Similar Questions

• While Tecra A2 shut downs message appears - TMEEJM_Wnd cannot be closed

  Have a Tecra A2 purchased in March 2005. I reinstalled the system successfully. When I try to shut down the system of windows open one after another with the message: "TMEEJM_Wnd cannot be closed." I have the ability to immediately close or cancel.

  What I do, the message disappears. Then the other window opens with the message: "cannot close WMS Idle". The same orders came. The system shuts down after clicking on 'Close' or 'Cancel '. With the "Systemrecovery" I put the system back. The problem is still there.

  Does anyone have any idea?

  Hello

  I discovered that this service of TMEEJM_Wnd belongs to the Toshiba Mobile Extensions utility.
  A similar problem appears sometimes on my laptop. It s not a portable Extensions Utility but Adobe acrobat reader cannot be closed and the laptop can not stop down.

  I reinstalled adobe und cleaned the registry with CCleaner and since that time, pop does not appear
  I think that if you don't need t Extensions Mobile utility you must either remove the BONE or you can try to reinstall again.

  With regard to the other message: WMS Idle
  See this Microsoft Knowledge base article:
  http://support.Microsoft.com/kb/921113/en-us/

• My computer started to shut down spontaneously hibernation mode and will not come out unless I'm hot restart.

  Curious... the power light flashing indicates also XP was put on Stand-By...

  Here's the manual where you can read about the Stand By and flashing, how come off stand by and maybe get some ideas:

  http://support.Dell.com/support/eDOCS/systems/dim9100/en/D86630LRs.PDF

  We will get the video information in msinfo32 as well:

  For information about video drivers, expand components, click view, click on edit, select all, copy and then paste the information here.

  Couple of things: 1) I ran anti-virus programs and found nothing.  It is probably because I have Webroot essentials running on my computer that pretty much catches most of the problems. ((2) I found the clogged fan grille almost closed with dust... I have now cleaned and 3) when I try to save power settings, I get an error message that says "Power Policy Manager unable to set policy - indicates two revision levels are incompatible."  I don't know if it's because I recently downloaded and installed the SP3 from Microsoft (so that I could download and install (upgrade to) Office 2010) which may be incompatible with Webroot?  I say it's when I right click the icon of the Service Pack 3 and click Scan, my webroot scan lights.  In any case, I've attached the information requested below.

  I hope that it is something as simple to clean my gird so the machine overheating... causing the closure.  My computer shuts down actually to the beautiful middle of my only uninstalling the software anti-malware you have suggested.

  Name ATI Radeon X 300/X 550/X 1050 Series
  ID of device PNP PCI\VEN_1002 & DEV_5B62 & SUBSYS_06021002 & REV_00\4 & 1A646D2D & 0 & 0008
  Adapter Type RADEON X 600 (0x5B62), compatible ATI Technologies Inc.
  Description card ATI Radeon X 300/X 550/X 1050 Series
  Adapter RAM 256,00 MB (268.435.456 bytes)
  Installed Drivers ati2dvag.dll
  6.14.10.6925 driver version
  File INF oem24.inf (section ati2mtag_RV380x)
  Color plans 1
  4294967296 colors Table entries
  Resolution 1280 x 1024 75 Hz x
  32 bits/Pixel
  0xF0000000-0xF7FFFFFF memory address
  0xFE9E0000-0xFE9EFFFF memory address
  Port of e/s-0x0000DC00-0x0000DCFF
  IRQ channel, IRQ 16
  Port of e/s-0x000003B0-0x000003BB
  Port of e/s-0x000003C0-0x000003DF
  Address 0xA0000-0xBFFFF
  Driver c:\windows\system32\drivers\ati2mtag.sys (6.14.10.6925, 3.40 MB (3 565 056 bytes), 11/02/2010 01:38)
   
  Name ATI Radeon X 300/X 550/X 1050 Series Secondary
  ID of device PNP PCI\VEN_1002 & DEV_5B72 & SUBSYS_06031002 & REV_00\4 & 1A646D2D & 0 & 0108
  Adapter Type RADEON X 600 secondary school (0x5B72), compatible ATI Technologies Inc.
  Description card ATI Radeon X 300/X 550/X 1050 Series Secondary
  Adapter RAM 256,00 MB (268.435.456 bytes)
  Installed Drivers ati2dvag.dll
  6.14.10.6925 driver version
  File INF oem24.inf (section ati2mtag_RV380x)
  Color of the aircraft not available
  Color not available Table entries
  No available resolution
  Bits/Pixel is not available
  0xFE9F0000-0xFE9FFFFF memory address
  Driver c:\windows\system32\drivers\ati2mtag.sys (6.14.10.6925, 3.40 MB (3 565 056 bytes), 11/02/2010 01:38)

• Laptop restarts when "shut down" is selected rather than close

  Most of the time when stopping down my laptop (start, stop the computer) displays a message indicating that Windows, but then stops it re-boots. As soon as he runs again, turn it off computer command works without fail. I am running XP Pro SP3. Any suggestions?

  Hi ClevelandErik,

  Follow the steps from the link below: Windows XP restarts unexpectedly or restarts when you shut down the computer:http://support.microsoft.com/kb/320299

  You can also check out the link below: Advanced Troubleshooting for shutdown problems in Windows XP:http://support.microsoft.com/kb/308029

  Windows XP Shut Down and auto-restart issues:http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/russel_02may13.mspx

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Portege Z10t-a remains in Standby Mode

  Good afternoon

  We had this a few times on different units of the fault. The Ultrabook seems to be in mode 'sleep' (flashing white power) and no amount of button walk / stop pushing, keyboard by clicking or mouse move it brings out of the State.

  Pressing power for 5 seconds the UltraBook will not shut.

  I have to wait until the next day when the battery drains completely before starting the unit.

  Is there another way to turn the power off, maybe?

  Right, you will find the Force closed down (marked with the number 8)

  

  Use an object like a paper clip and insert it into the hole.
  There is a little switch that will help you to turn off the unit.

• I started my computer and connected but have lost s icon on my desktop. I cannot close normally except by using the reset button.

  I login in safe mode and icons appear.

  I also checked device Manager with the warning icon in the network adapters.

  Teredo tunneling adapter 10 error.

  I get internet connection in safe mode but not in normal mode.

  I have windows 7.

  Little likely that would contribute in safe MODE - probably loads without network at all.  ;-)

  You can connect in safe mode, so... Create a NEW USER in safe MODE...

  1. Go to the--> user accounts Control Panel (user accounts and Family Safety--> add or remove user accounts--> create a new account--> account management of--> create a new account.)
  2. Give the user new administrator rights.
  3. Restart the PC and login as the new user.

  The new user works in normal mode?

  You can now, navigate to the location mentioned before see if (under your user name usual folder\desktop) icons you think Miss exist?

• My computer is starting & stopping down in safe mode... What can I do to fix it?

  My operating system is windows xp sp2... It is protected with bitdefender internet security 2011.but all of a sudden when I shut down my computer that he would shut down in safe mode... & then it starts and close in safety mode.what do I do to take back to the normal mode?

  Try raising 'msconfig' (start-> Run-> "msconfig").
  Once msconfig is running, click on the tab "Boot.ini" and check that the "/ SAFEBOOT" box is not checked.

  HTH,
  JW

• Failure to shut down Windows properly.

  When Windows is shut down, the system goes through the normal procedures and then gets stuck on "Closing Windows". The only way out of this is to cut the power. When the voltage on starting from the computer to the top immediately without the error message you get if there is a power failure. Can I stop this.

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://support.Microsoft.com/kb/308029

  It will be useful.

• My computer shuts down after 30 minutes, no screen standby, then when you connect, it says its locked?

  When I stop working on my computer (Dell Inspiron, aio, 2305) I noticed that the screen saver comes on and then it starts to Shut Down without asking to my. All I had to do it before (after the screen saver stopped) was click on any key and the computer was delivered.  Now, there is no screen saver, the computer just stops.  The log on screen, it says as my SMA, locked.  I have to enter my password.  This weird isreally.    Please help, before things get really out of control,

  Hello
  (1) have you made changes before the start of this issue?
  (2) what is the exact error message/code?
  (3) windows operating system you are using?
  Try to change the screen saver and check if you face the same problem.
  You can check the power setting and set it accordingly.
  See the link below:
  For windows 7
  Power management
  http://Windows.Microsoft.com/is-is/Windows7/products/features/power-management

  For windows XP:
  Configure Windows XP power management
  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/configure-power-management

  See also:
  What happened in standby and hibernation mode?
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-standby-and-Hibernate

  I hope this helps.

• cannot shut down my computer

  When you press the button "Stop the computer", the computer shuts down as usual.

  But recently, he stopped doing this.

  When you press the close button, it brings up a box saying "" standby mode".

  the computer turns off and restarts ten seconds later.

  I have to unplug the wall to make it turn off.

  We have windows xp professional Version 2002 Service pack 3

  Concerning

  Cathy

  Usually, a pc that fails to stop & restart itself, the fault is at the hardware level, add something new...

  Also, the BIOS has a 'power mgt' section inside using button operations, XP has this to be

  Control Panel, chk times.

• Satellite Pro P500 - standby and Shut Down crashing

  I have a Satellite P500. Bought new with Windows 7. It is new and has had a bad hard drive replaced.

  Since then, I've reconfigured everything and everything seems to be working - except when the sleep and the closure are activated, they do not work. Stop going just to close to the bottom of the screen and stays there for centuries until I force a stop down by holding down the power button. She won't be in standby mode and Hibernate properly either - drafts of the screen and hard drive starts to do something, but system remains active and fan works.

  I found another forum thread where something similar happening in the model of the A300, and someone suggested to turn off the wake-up on LAN and keyboard settings. Both of these Jefferson already out on it so go there.

  Help is greatly appreciated.

  Hello

  IF your laptop hangs on farm screen and doesn't go into hibernation/standby layout, I think that it s not bound as a result of the functions in the BIOS. This is more important if your computer starts up without any reason.

  Anyway, in your case I would of BIOS update.

  If this doesn t work you should try to reinstall Windows. This could also be a software problem.

• Satellite A300-1EC cannot load the OS and restart just /shuts down

  Can you help me with my problem of A300 PSAG0Elaptop.

  This is the case:
  before that I can still use my laptop normally without plugging the power cord but when plug the source ca the unit restarts all of a sudden. I charge the battery only when the unit is off. And now the worst case gets when I installed the recovery disk hoping would solve the problem. I can no longer load the operating system; It's just loading then it does not load and suddenly shuts down and sometimes simply frozen. I have not tried the safe mode, mode ahci, system recovery, system repair, and stil no chance.
  I brought this already at the center of ASP service and they demanded almost 1 unit brand new laptop for repair of my laptop is not advisable to send them to repair.
  I doubt that my system bios is not compatible with my vista Home premium OS, or perhaps my wife update of the bios that is not compatible in windows update. My current bios I checked is 1.4

  Given that I have no option instead of junking my laptop, I want to update or back to the original settings of the bios that can help to repair my device.
  Can you help me on how to update or revert to the original my system bios? As I can't access the windows can you teach me step by step using the usb port of my camera on system bios update? Or do you have any suggestions?

  Need help bad
  Here are the specs of my unit
  A300-1EC
  P / N:PSAG0E - 02J025AR
  Windows vista Home premium core 2 duo T5750

  Hey Buddy,

  First of all, the BIOS can only be updated Windows System. There is no other version that you can download on the site Web of Toshiba.

  But I doubt that this problem is caused by the BIOS. It s I knew not that it is possible to change certain values which make impossible Windows installation. With other words BIOS is secure and with all the settings, it should be possible to install Windows.
  An alternative you can press F9 in BIOS to load the default settings. That would be the best option.

  But according to your assignment, if Windows installation of recovery disc doesn t work and you are not able to charge the battery while the laptop is turned on it seems to be a hardware malfunction because seriously it has nothing to do with the software.

  So either come you into contact with the ASP to get the repaired device or you can repair yourself with original spare parts with parts ASP or second-hand on eBay or similar platforms.
  Of course, you can buy a new laptop: in case the motherboard would be defective because the motherboard is very expensive spare part, it would be the best choice in my opinion.

• HP Envy 4502: HP Envy 4502 printer is stuck in "shutting down" mode. Second time this has happened.

  My printer is stuck in a "shutting down" mode and has been so for 2 days.  This is the second time that this has happened.   I hope someone can help with this.  The power button flashes.

  Thank you!  Thank you!  Thank you!  It worked!

• printer is stuck in "shutting down mode.

  Printer stuck in ' printer shutting down "mode, will not be closed."

  I would suggest resetting the printer as follows: unplug the power cord from the printer.  Wait a minute, then plug the printer back in and turn on the printer.  The printer is correctly initialized?

• Send a message that the computer does not shut down properly after the resumption he out of the hibernation mode.

  My laptop has Windows Vista and is about 3 years old.  It is in excellent shape, but recently it has been brought to my attention that whenever I put into hibernation mode and resume, I receive a message that indicates that the system or computer is not stopped correctly, and so I have to restart the computer.   Why is this happening? and any solution for this?   Thank you in advance.

  Hi SuzanneSchwester,

  Thanks for posting your query in Microsoft Communities. It seems that you are getting a message that the computer is not shut down properly after the resumption he out of the hibernation mode. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  Follow the steps in the article.

  You have problems after you resume Windows Vista from sleep or Hibernate computer

  You can see these articles for more information:

  Solve power problems

  Turn off a computer: frequently asked questions

  I hope this helps. Let us know if you need more assistance.

  Thank you.