Presence with VCS and Findme

Similar Questions

• Cisco VCS and integration Lync2013

  Hello!

  Could you tell me please, when CISCO officially support Lync2013 - free new software for VCS - C and documentation on integration?

  The main interest is the possibility of transferring video between CISCO/MCU and Lync endpoints on the H.264 Protocol, who hails from Lync2013.

  Right now, I've got VCS - C and RTM Lync2013 X7.2. During the video call without AMGW appeal established as audio only.

  When using with Lync2010, it worked on Protocol H.263 and CIF resolution.

  Evgeniy salvation,

  We are currently investigating the possibilities to achieve interoperability between Lync 2013, VCS and video devices on the side of the VCS standards-based, it is a work in progress and at this stage, it is to early to provide any factual information on when interop will be available.

  In contrast to Lync 2010, Lync 2013 does not support H.263 for video and it so that will remove the OCS/Lync integration. I do however think that you should be able to make a two-way video between Lync 2013 and VCS-joined endpoints if you use an AMGW tried that yet?

  Thank you

  Andreas

• What is the difference bewteen MCU, VCS, and SRI (DSP-3)

  Hi all

  We lack CUCM 9.X. I want to integrate Cisco 9971, 8945 with TP Endpoint (EX60 and Tandberg C40). I read this wonderful document (https://supportforums.cisco.com/docs/DOC-30750), but I still have some doubts.

  What is the difference bewteen MCU, VCS, and SRI (DSP-3). For all I know, ISR running DSP3 is the chepaiest option but I don't know if the HD video is supported.

  Thanks regarding

  Remember messages useful rate by clicking on the stars below.
  Favor calificar todos las responses useful dando click in las estrellas mas abajo.
  ___________________________________________
  LinkedIn profile: do.linkedin.com/in/leosalcie

  Hello

  According to the document, you are referring to which I posted previously

  VCS is a call control system call manager but for video end points only, then CUCM is for voice and video, and now it becomes control system of very mature appeal for video communications with native support for video of many recordings of points

  MCU is a material that can be used to host the multi point/party video calls that can be registered to CUCM or VCS according to design

  SRI with DSP/PVDM 3 is the concept of the MCU, but can be used for small multi-point calls and normally remote sites that need local accommodation to a call to reduce the load on the WAN link when most of the participant in the same place for example! and it dose taken support HD but limited features compared to MCU

  for example PVDM3 doe does not support HD when participants are expected to use different video formats

  hope this helps

• Cisco VCS and LDAP for authentication of users

  I have a question about setting up LDAP for authentication of the user on the VCS. I want to have redundancy in my LDAP link. I believe that this is possible by setting a FULL domain name to the address of the LDAP server, then selecting a type of SRV resolution. What I'm not clear on is what the value for the server address would be if I used actually as SRV type of resolution. I should also add that I am looking to use TLS

  To clarify, if my AD domain name is myad.netcraftsmen.net. I have set the field as server address:

  myad.netcraftsmen.NET: assuming that VCS properly interrogate the DNS for the _service._proto correct parameters?

  or would I need to create an SRV record to that effect and set the field server address with the address (including the fields of _service._proto)

  or I need to specify one of the SRV records formats used by MS AD areas (there are several).

  If the latter, then what SRV record for TLS. I don't see records with port 389 (non-secure).

  My intuition tells me that this is probably the first option, but I could be far away.

  Anyway, thanks in advance for any input.

  Kind regards

  Bill

  Hi William,.

  I just checked it on a X6.1 VCS, and it seems that VCS searches SRV _ldap._tcp.domain (where 'domain' has been entered as the server address), both when the encryption is set to 'None' and 'TLS '.

  Hope this helps,

  Andreas

• ASA (v9.1) VPN from Site to Site with IKEv2 and certificates CEP/NDE MS

  Hi all

  I am currently a problem with VPN Site to Site with IKEv2 and certifiactes as an authentication method.

  Here is the configuration:

  We have three locations with an any to any layer 2 connection. I created each ASA (ASA5510 worm 9.1) to establish one VPN of Site connection to the other for the other two places. Setting this up with pre shared keys and certificates that are signed by the CA MS administrator manually work correctly.

  But when we try to enroll these certificates through the Protocol, CEP/NDE his does not work.

  Here are my steps:

  1 configure the CA Turstpoint to apply to the certification authority

  2. request that the CA through the SCEP protocol works fine

  3. set up a Trustpoint and a pair of keys for the S2S - VPN connection

  4. registration form identity certificate CA via the SCEP Protocol with a one time password works fine

  5. set the trustpoint created as for the S2S - VPN IKEv2 authentication method.

  Now I did it also for the other site of the VPN Tunnel. But when I ping on a host that is on a different location to make appear the Tunnel VPN - the VPN session is not established. In the debugs I see that there are a few problems during authentication of the remote peer.

  On the MS that I see that the certifactes of identity for both ASAs are communicated and not revoked or pending state. The certificate based on the model of the "IPSec (Offline).

  When the CA-Admin and a certificate me manually based on a copy of the model of "Domaincontroller" connection is successfully established.

  So I would like to know which is the correct certificate for IP-Sec peers template to use for the Protocol, CEP and MS Enterprise CA (its server 2008R2 of Microsoft Enterprise)?

  Anyone done this before?

  ASA requires that the local and Remote certificate contains EKU IP Security Tunnel Endpoint (1.3.6.1.5.5.7.3.6) (aka IP Security Tunnel termination). You can create a Microsoft CA model to add.

  If you absolutely must go with the 'bad' cert, there is a command

  ignore-ipsec-keyusage

  but it is obsolete and not recommended.

  Meanwhile at the IETF:

  RFC 4809

  3.1.6.3 extended Key use

  Extended Key Usage (EKU) indications are not required.  The presence
  or lack of an EKU MUST NOT cause an implementation to fail an IKE
  connection.
  

• With VCS-E media stream, VCS - C

  Hello

  We intend to implement a VCS infrastructure now I'm not sure wich accepting media between endpoints.

  On the photo, you could see the scenario.

  Endpoint 1 is communicate with the endpoint 2.

  1 medium Wich takes the media stream?

  2 what endpoint 1 communicate (media) with VCS - C and not directly with the two end point?

  2. must a direct connection between two end points?

  Thank you

  Martin

  Hi Martin,

  the media could pass control of VCS and highway always in a solution of course and course usage license.

  endpoint 1 must send to the control of VCS, and then it will be passed to the fast lane and then on internet and internet endpoint not directly.

  Rgds,

  Alok

• GW ISDN Cisco with VCS control

  Hi Experts,

  I'm new with Cisco ISDN Gateway 3200, and I will integrate to the existing video network managed by VCS control with the endpoints and MCUS registered as SIP.

  Here is an example of the existing video network numbering plan:

  SIP URI endpoint: [email protected] / * /

  MCU SIP URI: [email protected] / * /

  ISDN GW H323 alias: 54xxxxx

  I came up with these questions:

  1. for us intergate ISDN GW on the video network, we must save as H323 on the right VCS?

  2. to call scenario as a point endpoint SIP or MCU calling to one ISDN endpoint via video, how the call flow? Make the registered endpoint/MCU SIP point as SIP on the VCS can dial directly on this endpoint ISDN? Or they will call first the H323 number of ISDN GW recorded on the VCS then routed to an auto attendant of the ISDN GW?

  3. How about ISDN endpoint SIP endpoint?

  Please send me a sample of guide and the configuration of the ISDN GW and VCS about how we could improve the flow of calls work on the call scenarios mentioned.

  SIP---> ISDN

  ISDN---> SIP

  Thank you very much for the help.

  Best regards

  Acevirgil

  Hello

  1. For us to intergate the ISDN GW on the video network, we need to register it as H323 on the VCS right?
  

  Yes, it's true. This isn't the only method, but it is the most used and most easy way. I suggest you use it.

  2. For call scenario like from a SIP endpoint or MCU calling an ISDN endpoint via video, how's the call flow? Do the SIP endpoint/MCU registered as SIP on the VCS can dial directly on that ISDN endpoint? Or they will dial first the H323 number of the ISDN GW registered on the VCS then routed to an auto attendant of the ISDN GW?
  

  In this case, you will need to ensure interoperability the call in VCS. No matter what SIP endpoint can dial numbers ISDN, and then VCS will route the call to the gateway h323 format, only the number with any ' @domain.com ' and the call will be interoperability. The flow would be something like this:

  Point endpoint [sip] SIP----> - VCS [H323]---> Gateway ISDN

  3. How about from ISDN endpoint to SIP endpoint?
  

  The same concept is applied. ISDN gateway sends the call in H323 for VCS and interwoks VCS the call and sending SIP endpoint. Something like this:

  SIP endpoint<-------[sip]--------- vcs=""><--------[H323]---------- gateway="">

  With regard to incoming calls from gateway ISDN to VCS, there is one important thing to consider. You basically have to methods:

  • You can configure the ISDN gateway to route calls to the auto attendant, then users will be able to recompose the verse numbers of internal endpoint for the auto attendant
  • You can configure the ISDN gateway to use DID (Direct inward dialing), in this case, you create routes to the gateway which maps each ISDN number to an internal endpoint registered to the SCV

  Both methods work fine, however, when using auto attendant, it is very important to implement a scheme of toll-free fraud prevention. Take a look at this thread:

  https://supportforums.Cisco.com/message/3971947#3971947

  Regarding the guide, it is not a simple step by step explaining, but the Administrator's guide provides a good explanation on how to configure the dial plan in the gateway and how to enter the doors of VCS. Check out this guide:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/isdn_gw/admin_guide/isdn_gateway_printable_help_2-2.PDF

  I hope this helps.

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• Integration of Lync with VCS - key Option mandatory?

  We implement integration with VCS on x7.2 lync.  Using B2BUA with lync 2010.  Everything works internally with lync configuration, we are only having trouble with lync external participants come and we border routers in the mix.  Direct pools are set up under the name of trust.  We have turned on the highway of the tower.  The calls started from inward of Lync.  VCS sees calls says it is connected, but the appeal does not and then falls normal call clearing.

  My thought for the failure, is that the OCS Collaboration option key has not been added.  But I can't tell in the deployment guide, if this key is necessary only if the encryption is in progress.

  The other area that we now have on the border routers is if The Edge server and the firewall that the Edge transport server may move multimedia traffic through can then reconfigure to allow RTP over UDP and RTP over TCP to pass.

  Can you confirm if the key of the SCO is a requirement for Lync which crosses the highway?  And are there other areas which we recommend why calls set entirely outdoors.

  Hi Kim,

  the SCO cooperation improved option key is necessary for this scenario of appeal, stated at pages 13 and 53 in the Lync to X7.2 deployment guide:

  Calls on a Microsoft Edge server require the VCS have installed improved OCS Collaboration option key because this key allows the ICE to be used for media connectivity

  You are also right that you will need to allow RTP UDP traffic to and from your Edge transport server, as the TURN server on VCS Highway currently does not support the RTP over TCP. If this isn't the case, ice connectivity check between the B2BUA and the Lync client and server Edge fails, which in turn causes to disconnect.

  Hope this helps,

  Andreas

• Need some clarification on the operation of H323 with VCS-C/E

  We have our points of endpoints connected to the VCS - C with a VCS-E. When an end point called another unit through IP H323 the VCS - C does anything with the video/audio? He plays the intermediaries? Or is the VCS - C just let both units communicate DIRECTLY with each other (even when I see the appeal in calls in course VCS-C)?

  I try to debug problems with call and need some explanation on how it works.

  Thank you

  RB

  By default, call Routed mode should be on.  This means that the installation & signalling through the VCS, but all media streams are direct between endpoints.

  See you soon,.

  Paul R

• Multi-party sharing with VCS

  Hi, looking for some clarification.

  Can I use the multiparty licensing shared if I have a VCS rather than CUCM for call control?

  The ordering guide indicates that it would cooperate with the VCS.

  http://www.Cisco.com/c/dam/en/us/solutions/collateral/collaboration/PERV...

  page 4 - notes: although Cisco UWL Pro applies only to the Cisco Unified Communications Manager based deployments, SMP can be used with Cisco Unified Communications Manager and Cisco telepresence video Communication Server (VCS).

  The CUCM deployment guide

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/con...

  said only CUCM, not VCS - page 99.

  thoughts?

  Multi-party sharing (SMP) licenses can be used with VCS, the licenses that are managed by the Chief and not CUCM, unlike multi-party staff (PMP).

• Profile with VCS StarterPack

  Hello

  I have a Starter Pack with jabber client video VCS and a profile with the C40.

  I am trying to attend external calls directly in the profile, but without success.

  In VCS, I can see that the Codec is registered, but seems to go to the tool spot in VCS:

  "

  • Search (10)
  • State: Completed
  • Found: Fake
  • Reason: Not found
  • Type: H323 (RSQ)
  • Number of CallSerial: 159f54de-3586-11e2-8d85-0010f323030a
  • Tag: 159f5614-3586-11e2-ae4b-0010f323030a
  • Source (1)
  • • Authenticated: True
  • • Alias (1)
    • • Alias (1)
      • • Type: H323Id
      • • Original: Unknown
      • • Value: xcom - locate
    • Area (1)
      • Nom : DefaultZone
    • • Type: By default

  "

  Put a video of jabber, receiving the external call all works fine and Locator tool to find the device.

  It is some sort of bug?

  The profile TC5.0.1 and VCS StartePack version X7.2.1 version

  Concerning

  Can provide you information about your next situation?

  • Which consists of the video URL Jabber to the profiling system?
  • What system recorded on VCS-E Starter Pack profile alias?
  • What search rule you configured on VCS-E Starter Pack?
  • Any alias transformation configured on VCS-E Starter Pack?

• TMS, VCS and Jabbber "impossible to connect to the TMS on the VCS agent".

  Dear,

  We have Cisco TMS, VCSC and jabber deployment, we did before commissioning the VCSC and TMS and jabber worked well, but after the upgrade the VCSC v7.2 to jabber version 8.2 has stopped working and I can not connect more and when I go to the TMS and connect to the VCS I get "unable to connect to the TMS on the VCS agent" Please notify

  What TMS version do you use?  And you are using Extension of provisioning of the TMS (TMSPE)?

  Looks like you are using TMS Agent Legacy, which has been supported in VCS X7.2 and has since been removed from X8.1.  You will need to migrate to TMSPE and very probably upgrade your server TMS as well if you do not meet the minimum version.

  Cisco TMSPE 1.0 Deployment Guide

  Here's the guide deployment for TMSPE 1.0, there are newer versions, but 1.0 is one that you want to migrate from legacy Agent TMS.  Once installed and migrate your data, you can then go to the most recent version, which is 1.4 (see below).

  Cisco TMSPE with VCS 1.4 Deployment Guide

• VCS and design of Microsoft Interoperability

  Hi guys,.

  need help from collective intelligence again.

  I've got VCS and Microsoft Interoperability key installed and correctly deployed interop with Lync - audio and videocalls. Lync federated domains and successfully can call for their users. I have configured the search rules in certain areas (for example, Microsoft.com) neighbor B2B Microsoft box. call begins, but at time of pick up at the bottom it is declining.

  is it possible to appeal to domains Federated Lync via Internet of the endpoint TC recorded on VCS?

  You try to call the Lync federated users from your Cisco VCS registered endpoint? Have you configured the settings of the ROUND and for VCS configuration on the Edge transport server?

• I need iOS with airplay and without mirror 10

  I used my IPAD to stream Showtime for years now with Airplay without mirroring.  Now the new iOS 10 don't leave me with mirror and SHOWTIME seems to be the only one that will work with the mirroring on.  How do I get it off the coast of mirroring on the new iOS 10.

  Hello. The new control centre has two parts. Slide up, then to the left to access the right pane where you will see the devices available for AirPlay base already mentioned.

• load is0 10 to my iidown phone 6 s after finsh my phone restarts on the screen appear (photo and conncet quail itunes) iconncet my phon with PC and open my itunes

  ADOS iso 10 to my iidown phone 6 s after finsh my phone restarts on the screen appear (photo and conncet quail itunes) iconncet my phon with PC and open my itunes

  and stil again

  Take a look at these articles:

  Solve the iOS update and restore error in iTunes - Apple Support

  Get help with iOS update or restore errors - Apple Support