Print via router

Similar Questions

• HP Deskjet 5550: Printer sharing via Router/USB?

  So, I have an ASUS router with EZ printer sharing function. I have connected my printer to the router via USB but I can't find the printer in windows. When I surfed in to my router, I see the printer via the firmware on the router and the router has detected my printer model.

  I tried with the only available software for my printer, nothing helps. I also downloaded a software from ASUS, same progress. Any suggestions?

  Router ASUS RT-AC51U

  HP Deskjet 5550 printer

  10 Windows 64-bit computer

  Apparently I had to install an ASUS file on my computer, I just tried to run WinRAR. Problem solved!

• Cannot print via Epson WF-6590

  One of my users can't print continuously on our printer Epson WF-6590. The device is hard plugged into our network, the firmware is up to date and everyone in the office can print, except for a single user. It allows to print one or two times before either an error of communication or message filter has failed is displayed. It's a very intermittent problem, and more often than otherwise, this occurs when a host of jobs present one after the other.

  I have tried tons of troubleshooting steps. So far, include:

  resetting the printing system

  * Add the printer via the latest Epson PS driver

  adding the device by IP and Hello

  * permissions of the drive checked and repaired

  * updated with the latest OS (10.11.6)

  Any help would be greatly appreciated.

  Rob

  Have you tried to replace the network cable from the Mac of the router or whatever it is connected.

  Try it with a cable that you know works.

• Unable to connect to the printer via IP address

  I changed my ISP (internet service provider) and therefore changed routers - now unable to connect to the printer.
  I put a static IP address on my HP Photosmart B110a printer before we changed to ISP because there are connection problems. When we were setup to the ISP again, we are unable to connect to the printer, such as the printers IP 192.168.1.12
  The new network ISP IP range is 192.168.0.xx and printers address IP is out of the network.
  I can print via the USB cable but I can't return to my printers GUI by entering 192.168.1.12 return the printer back from the static IP address.
  A hard reset for this printer would be appreciated.
  Thank you very much.

  Hello
  I solved the problem. The answer was staring face heres so my solution for someone who has had similar problems.
  I didn't dig up the old router that affects the 192.168.1.xx IP network and then connected my PC, connected my printer then connected printers user interface through the static IP address, I assigned earlier. Changed to automatic IP. Connected my new router (which assigns the IP addresses of 192.168.0.xx) to my PC and printer. Everything is now OK.
  Thank you.

• Print via Wi - Fi on Photosmart Premium C309 connection problem on an iMac and MacBook Pro

  Hi all

  I just bought and installed a Photosmart Premium C309.

  I am running the latest Mac OS 10.6.5 on two computers: an IMac and a MacBook Pro.

  The printer software installation went well and I was able to print via USB cable.

  Then I connected the printer to my wireless network (Modem-Router: Fritz!) Box Fon WLAN), again without problems.

  I printed out a page of the control panel the printer network Test and got "no problems found. Congratulations on the successful your printer wireless installation.

  But when I tried to print via the wireless network, I continued to get "printer offline".

  I have disabled the firewall on the computer but no joy.

  Now, I'm unable to print via the USB port that the printer is "offline".

  Help!

  Thank you

  Problem solved! It has to do with Hello.

  When you set up the printer with the HP installation wizard must install the Hello printer drivers when you are prompted to choose the drivers. Simple.

  Thank you.

• HP Photosmart B110a: HP Photosmart B110a cannot print via wifi after upgraded to windows 10 notebook

  Before I updated to windows 10,

  I can print via wifi.

  But now I can't.

  the error says that there is some connection problems.

  But I could not understand what is wrong.

  We need to make a configuration under windows 10?

  Thank you

  Hi ma1210,

  Given that this problem occurred after the upgrade to Windows 10 I think your best option would be to uninstall the printer driver and reinstall Windows 10 drivers for the printer. You can download Windows 10 drivers for this printer by going to HP support at www.support.hp.com site - then enter your product information IE HP Photosmart B110a... change the Windows 10 operating system, download the driver and install it. According to me, which should solve the problem. All the best...

• I get "printer does not ' when I try to print via WiFi. Everything seems to be set up properly

  I went through setting up to print via WiFi.  When I try to print I get printer not responding do not.  When I boot I have a message "the printer is online."  I get a box showing that I am low on ink.  I can use the features of scanning from my laptop.  I can't print.

  I have a printer Canon MX882

  Lloyd

  Hi Lloyd,

  Thanks for posting this question in the Microsoft Community.

  To provide a proper resolution, I would need more information on your side.

  1. what operating system is installed?

  2. what security software is installed?

  3. don't you make changes to the computer before this problem?

  Follow these methods.

  Method 1.

  This tutorial is designed to help you identify and fix common printer problems in Windows, including print errors, print spooler errors, and other issues that could prevent you from printing.

  Solve printer problems: http://windows.microsoft.com/en-us/windows/printer-problems-in-windows-help#fix-printer-problems=windows-7&v1h=win8tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  Method 2.

  We can refer to this article and check if that helps.

  Why can I not print? : http://windows.microsoft.com/en-us/windows7/why-cant-i-print

  Feel free to post your request here on the Forums of Windows, we would be happy to help you.

• Impossible to print via USB using my iMac running 10.6.8 Officejet 4635

  I bought this printer all in one HP Officejet 4635 yesterday and are unable to print via USB.  I have an iMac running OS 10.6.8.  Until I'veI tried all of the suggestions that I could find on these forums (ex: downloaded the latest driver, disconnect/reconnect the power to disconnect/reconnect usb, delete and 'Add PRINTER' again, etc...) The computer does not recognize the printer, but displays "Unable to send print data" after I click on print.  I know that the printer works very well because I was able to send the document directly to his personal email address.   Help, please!

  Hello! Welcome to the @DanLA forums

  I have seen your post about how you can't use your Officejet 4635 with your iMac running 10.6.8. I understand that you have already tried troubleshooting, so please ignore all the steps that you have already tried in the list of my own suggestions below. If you still can not connect then, think of give us a call. I'll leave the details below.

  1. Mac OS X: how to reset the printing system
  2. Repair disk permissions
  3. Restart your Mac
  4. Reinstall the complete driver: 4630 Officejet HP e-All-in-One Printer full feature software and drivers series
  5. Try another USB cable
  6. Look for an update of the Firmware: get the latest Firmware and updates
  7. Make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on and can help.

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Good luck!

• printing through RDP remotely on the local printer via \\tsclient\ < printershare >

  Hi all!

  We have a customer who wants to print RDP remote at a local level
  AIO printer is connected. the printer is unable to print on the TS00x
  port - driver problem.

  now, we found, is it possible to print directly on the unc path of the
  printer when it is shared on the network.

  problem now is that the customer accesses the RDP session through a
  Web site while being not connected via VPN or something like that.

  attempted to map the printer via \\tsclient\
  local drives, if I select them to be shared to the remote system. the
  printer is not visible.

  When I try to connect to the printer in a command prompt with

  NET print \\tsclient\

  I get the not found network path.

  The printer is there because

  NET print \.<>

  works.

  in general - is it possible that I am doing?
  If so, what am I doing wrong?

  Thank you people.
  Markus

  Hi cRd_X,

  Try to do the following.

  http://support.Microsoft.com/default.aspx?scid=kb;en-us;q302361

  To resolve this issue automatically, click the fix it button or link. Click run in the file download dialog box and follow the steps described in the fix it Wizard.

  Solve this problem
  Microsoft Fix it 50180

  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• 1102w won't print via USB

  We have a 1102w currently used via USB.  It works perfectly with the macbook from my wife and my computer laptop windows 7.

  I have a macbook pro with the OSC v 10.9.5 and went through the routine to add printer, but when I print I can see that the document will print to the queue, the print queue empties but the printer does not print the document, the blue light flashes but no printing... any help in getting this problem would be greatly appreciated.

  Hi @richardskelt ,

  I see by your post that you can't print via a USB connection on the computer of 10.9, but you can print on the Macbook and the Windows 7 laptop. I will do my best to help you with this problem.

  Connect the printer directly to the Mac USB cable and run the updates Apple to install the printer.

  Verify that the correct driver for the printer name is listed.

  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (P1102w)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  

  

  Test the printer.

  If you're still having problems, follow these steps:

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Double-click disk utility.

  Highlight your hard drive / partition on the left.

  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click the Apple icon, and then click System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the + sign to add the driver, you may need to click the drop down menu to select the name of the printer, and then click the Add button.

  Test the printer again.

  If you need help, let me know.

  Good day!
  Thank you.

• We can connect HP1000 J110 printer via bluetooth

  We can connect HP1000 J110 printer via bluetooth

  No,

  The printer is a USB printer only.

  You can find the specifications of Connevtivity below:

  http://support.HP.com/us-en/document/c02231304

  Shlomi

• C6280, win7 cannot print via active network with VPN

  Hi, I have 2 PCs, one Vista, one on Win7. With Vista, I can print over the network.

  Also, via USB on the win7 PC I can print.

  But I can't print via active on the Win7 with VPN network. Without VPN, it works.

  I had several problems with the installation of the SW. Finally it worked (I think I had to turn my VPN connection)

  It recognizes the printer, the State says: ready, but when I print, I get an error after a while.

  When I stop the VPN, I can print.

  I tried to load the patch for Win 7 (recommended on HP circuit (printer disappears), but what it says that I don't have the SW right?)

  any idea?

  Hi ReneH,

  I am pleased to hear that the problem has been resolved. Have a wonderful day.

• my hp lazer jet p1102w printer resume printing via airprint when not available

  Hello

  I have the hp lazer jet p1102w printer. I've upgraded to the latest firmware.

  What is not available in the printer paper and I reload, it does not resume printing via airprint in my ipad.

  especially when I want to print on both sides. I can't resume printing. What should I do?

  Hello

  Once you have loaded paper in the tray, open and close the printer cover. who will resume the print job and complete it.

  Shlomi

• Printing problems on a M1120n MFP printer via the network

  Hello

  I bought a printer HP M1120n MFP, a couple of months.  I made sure that there the firmware up-to-date and that you have downloaded the latest drivers from hp.com.

  I can print and scan very well from the PC which is connected to the printer via a USB cable.  However, I can not usually print on the network of the other PC.  On the PC, I can ping the printer and I can also see the printer status page if I enter the IP address in a web browser on the PC.  So, I'm sure that there are no network connectivity problems.

  However, when I print to the printer on the network of these PCs, jobs just to stay in the queue for the printer.  Sometimes they print - but I don't see any model when they print.

  I would appreciate any suggestion on what to do, because I have to return this printer unless I can solve the problem?

  Thank you

  Bogman

  Thanks HP for quality and urged him to respond.  This has really increased my opinion about your company and the excellent support it brings.

• Connection to a printer via Bluetooth

  Hey all,.

  Is it possible to connect any device bluetooth compatible printer via the BlackBerry and print? It doesn't have to be complete documents with images etc. Looking forward to all the advice.

  Kind regards

  Schalk

  Check this thread.

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=12143&query.ID=46...