Problem adding a taskflow delimited using the ADF library

Similar Questions

• Single line vertical when using the ADF to Scan or copy on HP Officejet Pro 8600

  Printer HP Officejet Pro 8600 Premium (CN577A)

  OS: MS 7 64-bit

  When you use the ADF for my printer HP CN577A Officejet Pro 8600 Premium, I get a single vertical line on the document which is produced. This occurs when copying or scanning, both black and white and in color. If I scan or copy using the glass, I do not get the vertical line.

  I already tried troubleshooting.  I unplugged the printer, left without electricity for several minutes; that didn't fix the problem.  Then, I cleaned the rollers and glass; I always get the vertical line, but only when using the ADF.

  My firmware version is up to date (CLP1CN1150CR).

  What should I check next?

  The only difference between the ADF and scanning flat, from a point of view of the scanner is there on the glass, it happens.  I suggest you get a bright flashlight and examine the corresponsing area hence is the line, it's almost certainly a spot on the strip of thin glass which is being just in the right place.

  I've seen some people suggest that put a flashlight almost parallel to the Strip, it shines from the bottom can highlight the area problem.

• Office jet pro 8500 a: copy using the ADF will not work.

  I place the document in the top loader, it seems to be recognized by the machine, when I press the copy, it makes a funny noise but the document doen't go through the driver and the machine ask me to reload the document. A copy is fate. I checked if any blocking or jamming of paper but it's all clear.

  Been through the different troubleshooting steps, but nothing helped.

  Thank you very much

  Hello FROGYBEAR and welcome to the Forums of HP, I hope you enjoy your experience!

  I see from your post that you are experiencing supply problems.  I would like to help with that!

  I recommend you to perform a power reset. Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I would also suggest using this document on When you use the ADF, one "original jam: clear jam and press OK' Message displays on the all-in-one."  I understand the questions you see are a little different, but the steps should help solve that.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• 7520 all-in-One: 7520 all-in-One scanning now a straight line of the page when using the ADF

  A week ago I noticed that the analyses using the ADF put a black line about an inch from the right edge of the page.  This will not occur during the analysis of flat glass; only when you use the ADF.  I checked the glass and paper tray are clean and free of debris.  I wish that it there a way to display an image of what I'm talking about.

  The line is about the thickness of a vertical margin of Notepad and gray line.

  Someone at - it ideas other than buying another printer?

  BINGO!  That's all.  The glass was dirty.  Thank you very much.

• hp officejet pro 8600 premium: lines when scanning or copying using the ADF.

  I get a black page line everytime I try to copy or scan using the ADF. I tried to unplug the printer for 30 seconds and in him plugging everything into a wall as stated in a previous post. I also cleaned the glass for scanning.

  Hi RedShawLaw:

  Please follow the steps in troubleshooting found here.  The ADF uses a specific area of the glass.  A small piece of dust or smears may affect ADF scans, so special attention to the cleaning instructions part.

• I'm getting a vertical line in the middle of the page when I use the ADF on my Officejet Pro 8500 a but

  HP Officejet Pro 8500

  Windows XP

  No error message

  No changes to the system

  Scan using the ADF puts a vertical line in the middle of the scanned page.  This does not happen when I scan from the flat screen

  Brian, this is going to be a pretty easy fix. What you're going to need to get is a lint cloth (as a microfibre cloth or a filter coffee) and get just a wet touch. Then, open the top of your printer to reveal the glass. There are two sections, one large, and that is a thin strip of glass on the left side. If the line makes its appearance in the ADF scans/copies only - clean this thin section with a moist, lint cloth.

  This should help you!

  More information here: https://www.youtube.com/watch?v=SPdwUKnrDgM

  Let me know and have a great day!

• BlackBerry 10 Question on update to OS using the ADF.

  Question some time ago, I upgraded my Blackberry OS using the ADF. Everything installed properly, but I found two questions. One was could not download and install the driver from SD card (SD card is 64 GB) the second was Assistant of Blackberry does not really worked. I could type and it would work, but nothing happened when I used the voice. Is this a known issue or something I am doing wrong?

  Everything I heard, this source of Autoloaders contains intentionally paralyzed (for developer purposes) OS packages. You need a source that uses the final manufacturing code launched to build the autoloader. All that I understand, BB does NOT have any fully functional AutoLoaders with production code. It is clever users who have figured out how to create them. It's the source that I use and trust:

  • http://forums.CrackBerry.com/BB10-leaked-beta-OS-f395/BB10-OS-archive-943672/

  Of course, you must be careful and raised up on top of what is code of production compared to the leaks before you download and use any automatic charger.

• Problem with lines in Illustrator using the Wacom Tablet

  Hi all

  I have no idea why I'm having this problem in Illustrator. I use the small Intuos Pen Tablet (CTL-480), and my lines in illustrator is really strange. Even when I turn off the pressure in the brush settings, there is a gap in the line (it takes just one line of the same thickness). The Tablet works perfectly in Photoshop, but because I use the tablet to create art using plates (typography), it is easier and better for me to use illustrator. You are not sure that someone else had a similar problem or know maybe a setting I could change or try to fix it?

  I have attached a picture of the problem.

  

  

  Thank you for your help.

  This is a known issue.

  If all you want is a line single width, do not use brushes. Use the pencil tool and a simple blow

  If you apply a calligraphy brush, apply the effect zig - zag to it with a value of 0, then a setting of about 100 (turn on the preview to adjust)

• Problem using the gesture library

  Hello people, I am new on the platform of the Playbook. I read the source code for the most basic of apps sample available on the internet. I am facing some issues now that I am using the gestures library.

  I get an error saying undefined reference to gestures_set_alloc and swipe_gesture_alloc of the IDE, even if I have included the relevant header (gestures/set.h, gestures/swipe.h) files. After this i went ahead and downloaded the GestureSample from github (https://github.com/blackberry/NDK-Samples/blob/master/GestureSample/main.c) and tried to compile it, but I couldn't.

  Can someone help me understand what I am doing wrong?

  Looks like you don't have the library of action specified in your list of libraries.

  If you download the entire GestureSample on github, it has a configuration of a Makefile project which relies completely.  If you want to fix your current project, look at https://github.com/blackberry/NDK-Samples/blob/master/GestureSample/common.mk and make sure that all equivalent settings in your project are defined.

• I use the MODBUS library and can receive data, but I can send it very well?

  Hello

  I use the Modbus Library to communicate with a VFD to control a fan. I use the master write and read vi. I can write data to the drive mechanism and get the fan to do what I want. The VFD is supposed to send a package of confirmation after I told him to do something and I can also read its records. When debugging the VI it shows that the problem is that the buffer always reads zero and the VI timesout. If I look at the USB adapter lights to RS 485, I use to interface with the drive mechanism, I see that the flashes of light RX immediately after I send a message. So I should have something in the buffer. Does anyone have any suggestions?

  Aaron

  OK, here's what has happened to those who have this problem. In the series Receive.vi MB The bytes to the Port of property node has been reading 0 even if there was something in the buffer. Executing the program was then stuck in a loop until it expired and never went to read anything of serial port buffer. I didn't spend too much time wondering why that VI has not worked and created my own. Within a period appropriate after writing to the serial port, I used the same bytes to the Port property node and was able to get the exact number of bytes to the stream and then VISA vi the number of bytes to read. I received the message of the right answer and everything seemed good. But of course that NO! Then I experimented with different speeds of writing to the drive mechanism to get the fan to operate at different speeds. I found a small range of speeds where I get no response to the VFD, either in operation or by sending me a response packet. After a while, I found that there is a mistake in the LRC-8 code in the MODBUS library OR. It does not prescribe that the LRC will be a two-character value. So if your LRC is proving to be a single character such as F value (which should be 0F) you get an incomplete MODBUS message. This has been easily corrected in the vi LRC8 saying "number in hexadecimal string" vi to produce output with a minimum width of two. Then everything worked fine. Moral of the story, it's the MODBUS library is awkward.

• OR PCI-6542: Creation of dynamic waveforms using the HSDIO library

  Hello!

  I have problems to understand how to create waveforms using the HSDIO library to run on a card PCI-6542. I need to create a program that activates a channel for 12.5 microseconds, waiting for a while (i.e. 100 samples) and activates another channel to 12.5 microseconds.

  This program must be used in a Multielement ultrasound system.

  Here the example of dynamic generation program that transforms the channels 0-2 on 1024 samples.

  /************************************************************************
  
  *
  
  *  Example program:
  
  *    DynamicGeneration.c
  
  *
  
  *  Description:
  
  *    Generates a simple model on the specified channel.
  
  *
  
  *  Pin connection information:
  
  *    None.
  
  *
  
  ************************************************************************/
  
  / * Includes * /.
  
  
  
  
  
  #include "niHSDIO.h".
  
  / * Sets * /.
  
  #define WAVEFORM_SIZE 1024
  int main (void)
  
  {
  
     ViRsrc deviceID = 'Dev1 ';
  
     ViConstString channelList = "0-2";
  
     ViReal64 sampleClockRate = 50.0e6;
  
     DataWidth ViInt32 = 4;
  ViUInt32 waveformDataU32 [WAVEFORM_SIZE];
  
     ViConstString waveformName = "myWfm";
  
     ViInt32 timeout = 10000; / * milliseconds * /.
  ViSession vi = VI_NULL;
  
     Error ViStatus = VI_SUCCESS;
  
     Bruno errDesc [1024];
  
     ViInt32 i;
  / * Initialize generation session * /.
  
     checkErr (niHSDIO_InitGenerationSession)
  
              Deviceid, VI_FALSE, VI_FALSE, VI_NULL, &vi));
  / * Assign channels for dynamic generation * /.
  
     checkErr (niHSDIO_AssignDynamicChannels (vi, channelList));
  / * Set up the clock sample parameters * /.
  
     checkErr (niHSDIO_ConfigureSampleClock)
  
              VI, NIHSDIO_VAL_ON_BOARD_CLOCK_STR, sampleClockRate));
  / * Query the data Width attribute * /.
  
     checkErr (niHSDIO_GetAttributeViInt32)
  
              VI, VI_NULL, NIHSDIO_ATTR_DATA_WIDTH, & dataWidth));
  
  
  
     / * Fill the waveform with ramp data * /.
  
     < waveform_size;="">
  
     {
  
  	   waveformDataU32 [i] = i;
  
     }
  checkErr (niHSDIO_WriteNamedWaveformU32)
  
              VI, waveformName, WAVEFORM_SIZE, waveformDataU32));
  / * Start the generation * /.
  
     checkErr (niHSDIO_Initiate (vi));
  / * Wait for all the generation * /.
  
     checkErr (niHSDIO_WaitUntilDone (vi, timeout));
  Error:
  If (error is VI_SUCCESS)
  
     {
  
        / * Print result * /.
  
        printf ("made without error. \n") ;
  
     }
  
     on the other
  
     {
  
        / * Get the description of the error and print * /.
  
        niHSDIO_GetError (vi, & error, sizeof (errDesc) /sizeof (petitioner), errDesc);
  printf ("\nError encountered\n===\n%s\n", errDesc);
  
     }
  / * log * /.
  
     niHSDIO_close (vi);
  / * prompt to go out (for the popup console windows) * /.
  
     to continue...\n");
  
     GetChar ();
  
  error return;
  
  }

  Issues related to the:

  How can I change the values in waveformDataU32 to create market reports (instead of just always on)?

  How to select the channel waveformDataU32 is applied to the?

  Thank you!

  Zachary Geier

  The waveformDataU32 table is an array of 32-bit integers. Each bit corresponds to a line on the device.  On the first clock cycle, this program outputs:

  0000 0000 0000 0000 0000 0000 0000 0000

  Then it displays the following, changing at each clock Pulse:

  0000 0000 0000 0000 0000 0000 0000 0001,

  0000 0000 0000 0000 0000 0000 0000 0010,

  ...

  and so on all the way up to 1023:

  0000 0000 0000 0000 00000011 1111 1111

  In the example that you include at the bottom, you set the least significant bit (LSB) to zero and one, actually only change one line on the output. To change all the lines, you must instead use 4 294 967 295 or 0xFFFFFFFF:

  < waveform_size;="">
  
       < 200){="" if="" sample="" number="" is="" less="" than="">
  
            waveformDataU32 [i] = 0;     Disable channels 0-2
  
       }
  
       else {}
  
            waveformDataU32 [i] = 4 294 967 295;     Otherwise turn on all channels to 800 samples
  
       }
  
   }

• Using the bookmark Library, I can locate specific bookmarks, but there is no way of knowing which of my cases, it is in. Is it possible to do this?

  Using the bookmark Library, I can locate specific bookmarks, but there is no way of knowing which of my cases, it is in. Is it possible to do this? I have about 15 cases of bookmarks with a total of about 150 bookmarks. The research of the Library bookmark gives good results insofar as find the specific bookmark, but I IN. WANT to KNOW WHO MY RECORDS THE SPECIFIC BOOKMARK IS how can I do this?

  Take a look on these modules:

  https://addons.Mozilla.org/en-us/Firefox/addon/7372/
  https://addons.Mozilla.org/en-us/Firefox/addon/7377/

• Native extension using the shared library

  Hello

  IAM trying to create an extension which will be used in cordova, well the work of foundations... but what I have to do is add a shared library from another company for my project.

  They have a folder with all the files of all and a .so file, how can I add to my project and use it in the extension?

  Thank you.

  You start with the model BB10-Cordova?

  https://github.com/BlackBerry/WebWorks-community-APIs/tree/master/BB10-Cordova/template

  You should be able to add the library to the project using the Add Library Wizard in project-> generation properties C / C++-> the settings-> the tool parameters

  Note: It is recommended that you back up your project first.

• The data including labels and descriptions added to a photo in the photo library remains with photo

  original title: data including labels and descriptions added to a photo in the photo library remains with the picture even if I switch to a new computer without photo gallery

  I have some family photos and historical photos for my family genealogy. I am tagging these and adding descriptions such as when and where they were taken and that the opportunity was, etc. This information will always be with digital photography when I send to someone or see it on another computer?

  I have some family photos and historical photos for my family genealogy. I am tagging these and adding descriptions such as when and where they were taken and that the opportunity was, etc. This information will always be with digital photography when I send to someone or see it on another computer?

  ============================================
  Some metadata is stored in a database exclusive and is
  not written back to the photo files.

  If you right click on a photo and go to... Properties Summary / tab.
  Tip... you can see the data included.

• How to extract information from tree logical structure using the PDF Library?

  How to extract information from tree logical structure using the PDF Library?

  Adobe's PDF Library has PDSEdit APIs to extract information of the logical structure of a tagged PDF file.

  But I couldn't find any example code to demonstrate the C API on PDSEdit layer.

  I google search using different keywords, find none.

  I contact datalogics (which gives me the evaluation of adobe PDF library copy), no code sample on APIs PDSEdit yet.

  Everyone knows any code example can demonstrate extract structure logic tree information PDSEdit APIs (in C/C++ or Java)

  from a tagged PDF file? And is there any sample to demonstrate that connects a tagged logical tree contained in the content stream?

  I thank very you much in advance!

  logicaltree

  Did you look at the code snippets in the SDK?  There are a bunch of samples to work with PDSEdit and structure/marking.