Problem connecting to the FCO510 with RS232

Similar Questions

• Problems connecting to the internet with my wireless router

  I have a WRT54GS v7 wireless router that I use with a modem ADSL ZyXEL P-660R-D1. during installation, I was unable to establish a connection to the internet, once my router is properly connected to my desktop computer and my modem. All the correct lights on my modem and router are turned on. Please help, I tried to turn off the two as instructed by the installation wizard, but who failed to make the internet connection works and I continued the installation process after many attempts. At the end of the installation, he said that my router has been set up, but I don't have an internet connection. What should I do to fix this?

  The problem you are experiencing is caused by the fact that you Zyxel and your WRT54GS both try to use the same 192.168.1.x subnet.   Your WRT54GS will not work properly if you try to put the same subnet on the LAN ports and the port Internet (WAN).  Also to note that the installation wizard will not work in your situation, then stop using it.  You will need to manually configure your router.

  There are two ways to solve the problem:

  Option 1) Change the subnet in the WRT54GS.    To do this, follow these steps:

  (a) turn off your network

  (b) disconnect the WRT54GS of other devices.

  (c) connect a single computer via ethernet cable, a LAN on the WRT54GS port

  (d) turn on your computer and the WRT54GS

  (e) point your browser to 192.168.1.1 and connect to your WRT54GS

  (f) change "local IP address" 192.168.2.1, then click the 'Save Settings' button and wait (3 to 60 seconds) of the screen refresh.  You will be probably disconnected from the WRT54GS.  Don't worry about this.

  (g) take out your browser and turn off the WRT54GS and your computer.

  (h) then, using an ethernet cable, connect the Zyxel ethernet port to port Internet (WAN) of the WRT54GS.

  (i) power of your network.  It should work.

  You will now access your pages of configuration WRT54GS to 192.168.2.1

  Option 2) the other way to solve your problem is to change your Zyxel to 'bridge' mode  (You will need to consult your Xyxel user guide, or your ISP website, to find out how to do this).  This will convert the Zyxel a real modem, and then he won't get an IP address.  After that, you need to configure your WRT54GS to your PPPoE connection for you.

  I guess that your Zyxel is a PPPoE connection.  If we perform a PPPoA connection, then does not allow Option 2 because your WRT54GS is unable to make a PPPoA connection.

  Additional notes:

  You don't need to do both options.  Choose one or the other.

  For a more normal web use including browsing, email, downloads, etc., or another option should work fine.  If you are an online gamer, you will probably prefer option 2, because this will make it easier to set up many online games.

• Having a problem connecting to the internet with Workstation 6.5

  I have a problem with access to the internet on Windows Vista Business x 64 on VMware Workstation 6.5. My computer is Windows 7 professional 64-bit. I left everything default settings. On my host computer, I have my connection wireless connected to my router to get a IP through DHCP and it is connected and on the internet. I also have more than 2 connections, VMware Network Adapter VMnet1 VMnet 8 are listed as no access Internet under Access Type and are listed as unidentified network. On my guest OS I am connected via Nat and when I start first of all my virtual machine that my network card shows as connected with local and internet access but after 5 seconds it only local changes. My host uses a system of IP of 192.168.1.x and my guest operating system is using 192.168.19.x. I don't know where to start. I tried google and know disp. I hope I have not confused things by giving too much information that can be irrelevent and maybe omitted important things. Help, please. Thanks in advance.

  Check if the host firewall disabling resolves. Also (I know you use not packed, but check anyway) http://kb.vmware.com/kb/760

• I have a problem connecting to the internet with remote access.

  Hi I have a laptop Dell Inspiron. I installed Vista and now I am unable to get on the internet. I use the dial upward at home. None of my ISP disc make me on the internet... It gives a message that there is a problem with the hardware. What can I do to fix this?  I had XP before and it worked fine.

  Hello

  Hello

  Make sure you have the latest vista drivers for your computer which you can get your computer manufacturers Web site

  go to their website and look for a driver and software download section

  Enter your model number for the last look drivers vista then download and install

  http://support.Dell.com/support/downloads/index.aspx?c=us&l=en&s=Gen

  If there is no vista drivers available, you're out of luck and that the machine was not built by Dell for vista

  If necessary, use another computer to download and save = copy to flash drive - transfer and then install them

• Problem connecting to the server after moving

  Hi, I keep getting the message "there is a problem connecting to the server"192.168.0.19"etc. This happened after I moved. New ISP, new router. I have an Airport Express and a NAS connected to it. Time Machine and Icloud on the NAS. I think that the NAS has this IP address before moving. There are now 192.168.10.176. Everything works, but I get the pop up frequently.

  I look at the accounts and start but nothing. I reboot safe mode does not remove the problem. So, what can I do?

  I'm on Yosemite with MBR.

  Can you connect using the new IP address?

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph

• Check error: there was a problem connecting to the server Apple ID

  When I try to connect to my iTunes on my Windows laptop account it is said there is a problem connecting to the Apple ID server. This problem did not begin until 2 days. I have the latest version of iTunes and Windows.

  What is the number of the version of iTunes?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  Start by missing error MSI.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  Leave a post by: turingtest2

  On the PC, when connecting each device, it loads a separate driver. You can try this trick when you want to get iTunes recognizes the iPhone 6. Thanks to the user of the CSA turingtest2 for the tip.

  Try the following:

  Open Control Panel > Device Manager

  Plug in your device

  Locate Bus USB Controllers > Apple Mobile Device USB Driver.
  It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.

  Right-click and select software update of the driver...

  Click Browse my computer for driver software

  Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
  C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers

  Click on let me pick from a list of drivers for devices on my computer

  Click on Apple Mobile Device USB Driver

  Click Next, then close and exit the Device Manager

  Leave a post by: ChrisJ4203

• Unable to connect to the internet with Foxfire. Can do with Internet Exporer

  I've been using Foxfire. After an update I can no longer connect to the internet with Foxfire. IE can connect.

  Firefox is the name. Foxfire is a bio-luminescent fungus.
  
  http://en.Wikipedia.org/wiki/Foxfire _ (bioluminescence)

  See this support article - difficulty of problems connecting to websites after Firefox update

• Satellite A500 - 15 M: unable to connect to the TV with HDMI

  Hello

  I have a Satellite A500 - 15M. I recently tried to connect to my TV so I could watch certain shows online on my Hannspree Xv HD ready TV.
  The HDMI out does any record on the TV - the TV displays a message "not supported" and remains off (as if there is no signal) - display settings on the PC it does not recognize the TV... actually it [Intel Graphics and Media Control Panel] indicates that the TV/monitor settings are not supported.

  But I can connect via the VGA output - although I have to delete the display settings to 1024 x 768 to show on TV. In addition the display on the TV then is mainly pink and red, even if my pc display peak is most often blue. -start of the Toshiba screen displays on the TV, without any problems and one or twice the login screen was displayed too much, but then sometimes it isn't...
  I know that's not the VGA cable as I can connect to the TV with it on netbook advent my wife without any problem.
  Are there drivers, I need to update / download? Or I need to change the settings?
  How can I get my screen on my TV?

  Any help would be greatly appreciated. Thank you

  Hello

  First, you must connect the two machines (laptop and TV via HDMI) when the two devices are turned off. After turn on the TV and the laptop.

  You must choose the HDMI on TV channel and should then use the FN + F5 key combination to switch the video output to the TV.

  If this does not help, try updating the graphics card driver.
  It seems that your laptop supports the Intel graphics chip. Therefore, you can see the Intel page for new drivers.

  Welcome them

• There was a problem connecting to the network

  It identifies the network properly even when I put the password - and that is the password - the comment poster 'there was a problem connecting to the network.  The WiFi network, you are trying to reach cannot be found. "Yet he already told me that the network is correct.  Frustrated!

  Is the network that you connect to your personal or public?  On my home network, I turned on an access control and when you are trying to connect with an unauthorized device, we get similar behavior.  It does not connect despite all the correct information.

• computer not automatically standby (formerly titled "impossible computer automatically sleep when it is connected to the internet with modem cable")

  Hi, I noticed recently that my computer (Windows XP Media Center Edition 2005) is unable to sleep automatically when it is connected to the internet with a cable modem. Change the settings for my current power mode and try a different feeding regime (diagrams of Windows XP default power and power management, I created) only solves the problem for 2 days at most. I also tried to change the settings for the other power plans mentioned, and yet once again, the problem was only set for two days at the most. I also tried turning off my computer, restarting my computer, recording Powercfg /Restore Default policies in Run, saving sfc/scannow in Run, and again, I got the same result. Reset and power cycling the modem cable is not helped either. To help you better understand the problem, for example, if I had the date set for the screensaver set to 1 minute, the time for the monitor to turn off set to 2 minutes and time for your computer set to 3 minutes, the screen saver activate after 1 minute, the monitor turns off after 2 minutes, but the computer would not sleep mode after 3 minutes , even after an hour or more. I tried to check the Task Manager, and I have not noticed any process that would be interrupting the day before. However, I noticed that when I turned on the monitor by moving the mouse, even when the computer was unable to sleep and unplugged the ethernet cable from the cable modem and waited, the computer has entered standby as it should have.  I tried to find a solution for more than a week, contributions for this issue would be greatly appreciated. Thank you for taking the time to read my post. (Update: it seems that the problem is something else then my cable modem.)

  Hello

  Thank you for the update.

  This behavior can occur because of possible conflicts of third-party software, which includes the third-party security software.

  You can also temporarily disable third-party security software and firewalls installed on the system and check the issue.

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program. Please contact the software vendor for assistance in this regard.

  Note: be sure to enable the security software on the computer after checking the issue.

  Note: When you perform a clean boot, you can activate services for the modem, network card and disable third-party services to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• Server connection error:-1 there is a problem connecting to the server... hp photosmart 5510

  HP photosmart 5510 e - while a printer B111a

  Windows vista 32-bit

  connection error message-Server error:-1 there was a problem connecting to the server, press Retry or ok to continue

  No changes have been made to my operating system

  Try to add new applications with eprint center of my Compaq Presario CQ60 laptop to my HP printer. Computer tells me that the new applications are there and ready to use, but printer says 'server connection error "? I followed all the instructions to connect to the wireless router, but I'm not sure how to connect to the "Server"?

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. tap the wireless at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.
   
  4. click on networking on the left.
   
  5. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  6. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  7. click on the network address (IP) on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.

  Let me know if you have any additional questions. Thank you!

• having problems connecting to some websites with spa3102

  Hello

  I have problems connecting to some websites with spa 3102.

  The error message I get is as follows.

  The connection was reset

  The connection to the server was reset while the page is loading.

  * The site may be temporarily unavailable or too busy. Try again in a few
  moments.

  * If you are unable to load any pages, check your computer's network
  connection.

  * If your computer or network is protected by a firewall or proxy, make sure that
  that Firefox is permitted to access the Web.

  When I connect to my ISP modem directrly, so I'm able to connect to these Web sites.

  Any ideas?

  I already had the latest firmware (software Version: 5.1.10 (GW))

  But I think the problem is now resolved. Sites that I couldn't visit were my suppliers Web hosting and my own domain. Previously, I had activated attacking and that my hoster somehow registeren my mac address.

  Here are the settings that I had to change the spa3102.

  MAC Clone settings
  The Service Enable MAC Clone: Yes cloned MAC address: xxxxxxxxxxxx

  thx for your help.

• "Problem connecting to the Server Web Services." - HP Envy 100

  Hello world

  I wonder if anyone has the same problem as me. I just got a HP Envy 100 and went through the process of setting up without problem. The printer is connected via Wi - Fi for wireless network, I can ping the printer from my Mac successfully and I can print within the network without problem.

  However, regarding ePrint and Web features, it seems that nothing really works. I can't even turn on Web services, I always get the message "problem connecting to the Web Services server.

  I tried the following:

  -Restart the router and printer

  -Change the manual IP address and manually set the DNS server

  -Reapply automatic IP and set the Google DNS (8.8.8.8 and 8.8.4.4) servers

  .. .with no chance whatsoever. If this is a problem with the firmware (from what I understood, I do not have the latest firmware, but I can't ask her update, because it requires, you guessed it, a connection on the server of web services, that is the whole of the problem.)

  Anyone else having the problem? Everyone had it and fixed it? Is this just a temporary problem with HP servers?

  Thanks in advance!

  Hey, for me it works as well, and I didn't, just retried that I had tried before and it connected to the Web Services without problem.

  So I think it's safe to say that the original problem in this topic only lied to a HP Server-side problem. Not cool it took so long for them to solve and in particular the fact that we did not really have feedback appropriate about the problem.

  Anyway, I solved (for now, at least).

• Unable to connect to the internet with other programs (like Zune) but internet explore still connects.

  I can connect to the internet with internet explore very well. No problems.  But when I try to connect another program to the internet, like Zune or Wildtangent games the program says that I'm not online.  I know that I'm online because I check to make sure you Internet explore, and which still works.  I already tried to change the firewall settings to allow programs through, but that did not work either

  Hi Chloe,.

  1. What is the exact error message?
  2. Since when are you facing this problem?

  However, try the following steps.

  Step 1: Add zune except for windows firewall.

  1. click on start toreduce this includes this image, type firewall.cpl in the Search box and press ENTER.

  2. click allow a program through Windows Firewall. Collapse this includes this image
  If you are prompted for an administrator password or a confirmation, type the password, or click continue.

  3. click on add program.

  4. click on Browse.

  5 locate the Zune and then click Open.
  Note By default, the Zune is installed in the following location:
  C:\Program Files\Zune\

  6. click OK twice.

  Step 2: Windows live onecare

  1. Start Windows Live Onecare.
  2. Click change Onecare settings.
  3. Click the firewall tab.
  4. Click on Advanced settings.
  5. Scroll through the list of programs to determine if Zune appears in the list.

  ·         If Zune appears, make sure that the Zune is set to allow instead of block.

  ·         If Zune does not appear, follow these steps:

  1. click on Add.

  2. Locate the Zune and then click Open.

                  Note By default, the Zune is installed at the following location: C:\Program Files\Zune\

  3. click OK twice.

  http://support.Microsoft.com/kb/927980

  Try these steps and let us know the result.

  Bindu S - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think