Problem with my COMPAQ laptop model M2235AP

Similar Questions

• Problems with drivers for laptop HP650

  Hello

  I have a problem with drivers for this model.
  I have installed windows 7 32 bit, then removed all the drivers from the official website of HP, but a problem with the two drivers, PCI SIMPLE COMMUNICATIONS CONTROLLER and CONTROLLER ASSISTED, now I can't connect to Internet, LAN or wireless internet.

  Is there a solution?

  

  Hello:

  This is the driver you need for the PCI SCC.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5225011&prodNameId=5225013&swEnvOID=4062&swLang=13&mode=2&taskId=135&swItem=ob-104656-1

  In order to find the right driver for the wireless card (since there may be one of several different model wireless cards in your notebook), go to Device Manager and click on the network controller needing drivers and display the material for her ID.

  If you don't know how to find the hardware ID, please read the info on the link below:

  http://www.DeviceDriverFinder.com/blog/device-drivers/how-to-check-the-hardware-ID-for-a-Windows-device

• Problem with my Acer laptop does not connect to my home network.

  Hello

  I had a problem with my laptop. The laptop does not connect to my home network.

  I found the wireless network, but when I hit enter after entering the password (), suddenly a pop up come that said "Windows could not connect to the network". The laptop connects well with portable hotspot in my phone (3 G Tethering). But my phone (Samsung Galaxy Pocket) connects to the home network.

  My specs:

  Acer Aspire 4250 ongoing Windows 7 SP1.

  Dlink DSL-2730u (secure wifi with WEP 128 bit key)

  Please solve my problem...

  Original title: problems with my Acer laptop

  Guess - encryption levels are the same. E.g. is your set of router that you use WEP only but your PC configured to use WPA only? http://Windows.Microsoft.com/en-HK/Windows7/set-up-a-security-key-for-a-wireless-network

  If this is the case try to configure WPA2 or WPA rather than fall to WEP.

  Check all the other related settings as well. knowledge is the router using MAC filtering, are there available IP address so that it can allocate? (some routers are possible to limit the amount of IP address, they can allocate at one time).

  Second, if it does not remove the encryption all and see if it connects then. JUST AS a TEST, do not leave it.

• Problem with the Compaq Presario CQ60-216DX

  Hello, I'm having a problem with my NEW Compaq Presario CQ60-216DX mother. Every time it boots up vista and I run internet explorer, I get a strange blue screen which exports a file memory and reboots.

  I have the feeling that this might have been caused by a virus, but I can't do something, because Vista can't reformat long for some reason any.

  I tried a hard test in my motherboard and he said that there is something wrong with my hard drive.

  I don't know what is happening, right now I'm in safe mode trying to find viruses that Nod32 does not detect everything.

  Can someone tell me how I can get either the Windows XP Discs to work at startup (which, for some reason, they do not), or an alternative to a long format?

  Is there a way to fix this without reformatting? There's almost nothing on this laptop anyway so I'm always willing to do. A regular format has done nothing to solve the problem, I did it with Ubuntu and it did a quick format, but I had no problem with Ubuntu. Then I reinstall Vista and I am constantly having problems with a blue screen of death.

  Someone knows how to fix this?

  The Chemich does not exist

  If you want to do a reinstall of Vista then press F11 continuously during the boot upward. This will bring you in Recovery Options were you can choose to restore the system in the same State as when it was purchased. But if, as you suggested, is that a problem of hard drive reinstall won't help.

• Hey I had a problem with my compaq cq62

  Well this is saying me tha theres no drivers on the pcwhen I try to program it, but on the screen after the compaq sign spell he found bootablr device. Insert a bootable CD, then press to continue, can I get help on this

  No boot device would mean that it cannot read a boot sector of any of the devices detected by your machine.  This could be because the hard drive is bad, the boot sector is damaged or you let a non bootable DVD/CD in the drive.  You can enter the bios and see if you have all of the hard drives listed or recognized by the system?  My best guess is that you have a problem with the hard drive.

• HPL2208w of the problems with the new laptop.

  Hello

  I have a 22-inch HPL2208w monitor, which seems to play on my new laptop Dell upward. The laptop has only a HDMI port, so I connect the monitor's vga cable to the Dell via an adapter.

  The display shows for a few minutes and requires only the range (I guess resolution) be changed to 1680 x 1650. For some reason I can't change the setting of the laptop to that. When I do not change the resolution (only if the monitor is unique and not dual output) the warning message remains on the screen and the screen is not at its best (wise clarity).

  Series Dell Win 7 64 bit, but the monitor was working on my previous Dell with the same version of Windows (with a VGA connection).

  Kind regards

  HA9005

  Hello HA9005,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that you are having problems with the resolution on the HP L2208w 22 '' monitor and a Dell laptop. Unfortunately, as the monitor don't has no options that you can change in what concerns the resolution (it is passed by the laptop), I suggest that you try the Dell Forums for an answer.

  I know maybe it's not the answer you are looking for, but at least you know where to look for the answer now. Thanks for posting on the HP Forums. Have a great day!

• Problem with the HP laptop webcam

  I'm having a similar problem, I have a laptop HPG7000 with 32-bit operating system with built-in-cam, the camera just stopped working.  have tried uninstalling and reinstalling all sorts of updates and drivers but to no avail.  even called HP, but they have not yet solved the problem.  Instead, I use an external webcam for the moment but I would appreciate if each of us having similar problem go to the bottom of this...

  Hello

  Look at the website of the manufacturer of your system for the drivers of the device which is HP.

  HP support
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Problem with the Compaq 6715 network s

  Dears

  I have compaq 6715 s running windows XP SP3

  I have a problem with my network connections, whenever I am connected via the LAN port Ethernet, wireless connection is automatically disabled and I can't enable it.

  is this normal or should I do something to use both connections at the same time to connect to two different networks.

  Thanks in advance for your support

  Hello:

  This is perfectly normal, and you can fix it easily also.

  Go into the BIOS and in the sub-menu of device configuration, modify the LAN/WLAN, set active to disabled.

  Save the setting it by hitting the F10 key and again when you go out (save the settings and exit).

  Now the wireless stays on when you connect by using a LAN cable.

• problem with my computer laptop hardware/driver.

  I have a laptop lenovo z570 to hv with win7... from AFTR, on the desktop, the last icon is selected automatically... even whn, I opened my man or recycled bin that opens the last shortcut... BT when I press any key in keybrd the problem disappears... sometimes moreovr to start the 'starting windows' screen freezes... in the same way whn I press a key to start the windows... I have lots of hv formatted my computer laptop aftr the prob... bios update... BT no result... what to do? pls help.is it any hardware problem or any other thing?

  Hi Anurag,

  Thank you for keeping us posted.

  Could you please check with support from Lenovo because it seems to be a problem with the hardware.   I suggest that you post your question in the support forum for Lenovo.

  http://forums.Lenovo.com/

  Keep us updated with the status of the issue.

• Problem with my Lenovo laptop battery.

  • my laptop shows the battery error "there is a problem with your battery , so that your computer could turns off suddenly."
  ""Consider replacing your battery.".
  • When I updated my windows 7 with the help of windows update and restarted the error, it has been shown. Please give me the solution.

  Having your charger and verified by a reputable repair facility, approved.  Batteries wear out over time.

• Problem with my computer laptop vaio sony windows 8

  I am facing a problem when starting my computer sony vaio notebook. My laptop is sony vaio laptop with system of operating Windows preinstalled (unilingual) 8. Unfortunately I stop my laptop while the blue screen displaying 'Preparation to set up windows' and then a blue screen showing "Your Pc needs to be repaired" appears. (I think that the boot partition is damaged at the display of the code as 0x000000)

  Recently I install ubuntu alongside windows 8 so I think it might be the problem.

  The main problem is that I can't open anything, not even command prompt options to rescan advances and rebuild boot partition and I have windows key 8 to reinstall completely since it's preinstallation with it and I have no cd/dvd recovery.

  Please help me I'm stuck.

  I have attached a screenshot with it.

  

  When I walk in the first option IE start rescue and recovery the same screen appears with your PC needs to be repaired

  Hello

  You have to solve this problem with Ubuntu and support from Sony. You are probably
  need to remove Linux and Linux boot loader and restore if Windows startup
  There may be other options.

  Sony - Contacts
  http://eSupport.Sony.com/us/Perl/contact-land.pl

  Sony - drivers
  http://eSupport.Sony.com/Perl/select-System.pl

  Sony - Support
  http://eSupport.Sony.com/

  Sony - Forums
  https://Forum.sel.Sony.com/?XID=M:Showcase:eSupport

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Problems with video streaming (laptop HP with windows 8)

  When I stream videos or watch a DVD with my HP laptop, often enough the video slows way and audio will sound very strange-sounding and the dialog box is slow and very robotic, sometimes, when this is the case I will also have a pop-up indicating that the silverlight plug in has stopped working. I have the window pop up maybe 1 out of 10 times the problem occurs. Can you tell me what could be the cause of this and how can I solve this problem? Please and thank you :-)

  Hi Dephne,

  This problem may occur if an existing Silverlight installation or uninstall has become corrupt.

  You can see the following article from Microsoft to clean installation of Silverlight on your computer and check if it helps.

  How to manually clean a Silverlight broke in Windows 8 installation

  http://blogs.msdn.com/b/webapps/archive/2013/05/23/how-to-manually-clean-up-a-broken-Silverlight-installation-in-Windows-8.aspx

  I hope this helps.

  Please report if the problem persists and we will be happy to help you further.

• Problems with the pages of models CS3

  My site is www.cft-aft.org and I have problems with a page or two that were created from a master template that the images are not loading or projection. An example can be found at http://http :// www.cft-aft.org/Get%20Involved.html. I don't know what the problem is or how to diagnose.  All pages of this website have been created from the master template. I had some file management problems in the past, and I think I have corrected most of them (with the exception of the change of name without spaces). I understand that this could be a problem and if it is my problem with this specific page, I understand.

  I have attached a few screenshots of the presentation of dreamweaver and a screenshot of my side of local and remote sites.

  The main problem with the page get involved is not editable images do not exist. Everything lies in the local root folder of the site/htdocs, on both sides. I noticed that when I do to the top of the page get involved in DW is at the top right of the screen, he reads a long path (shown as an example on the screenshot) and on other pages which load correctly, the path is not the same thing, but they reside in the same folder. I suspect that this is probably my problem, but I'm confused, how it got like that and worse still, how fix without having to completely rebuild the page.  I am a total novice and teach me how to do this using the DWCS3 Missing Manual book, but I can't find a solution in there, so please help if anyone can, with step by step instructions.

  If anyone has any idea how it happened, I'd appreciate comments so I do this again.

  If more information is needed, please let me know.

  Thank you

  Hi, Kelly.

  What keeps you from renaming files with Word spaces? It is a good idea. On ALL of your files. Rename them to the INSIDE of the files Panel.

  You work in a defined site? Yes, you are.

  The page you we directed (with an address disheveled, but easy to fix on the track), shows a large number of links to files on your computer, do not using links to other files in your root directory.

  You must open your template and reapply links to all images. Save the model. Once you have re-applied the links in your template Master.dwt, change > models > update of the Pages... while your model is open (especially if DW does not ask if you want to update the files). Record everything (better yet, don't have other pages opens when you update the pages...).

  Depending on how you created your page "Se Involved.html", it would be preferable for you to set up a new page of the child of your template and copy the changing content of the old page. Name the new page (without spaces in the file name... lol...) and save it. You won't be totally rebuild the page, because a lot of it will flow in your model.

  Commenting on your illustration to pdf, you want the indicator model-based Yellow Page in the upper right of your page based on a model of read model: Master. Pages containing the path to the top there are incorrect. I don't know how this happens, but it could be a problem with moving the files outside the DW (bad idea)... always use the files Panel to move files. You have full access to your computer in this window.

  Beth

• Problem with the HP laptop keyboard model of product: J2C46PA

  9871019173

  Hello

  I recently bought a new HP laptop with below the description. "When I try to type @ symbol using shift + @ it shows double quotes (" ") and vice versa when I hit shift and" it shows (@). its really frustrating that a company like HP is not still maintain QC before shipment.

  Any help would be much appreciated.

  Thank you

  Nigam

  Product model: J2C46PA product name: HP Pavilion p027tx-15 Notebook PC serial number of product: [edited by Moderator serial number]

  Hello

  It sounds like the evil of keyboard has been defined - you can change it as described in the following link.

  http://www.howtogeek.com/121169/how-to-change-your-keyboard-layout-in-Windows-8/

  Kind regards

  DP - K

• His problem with non-Toshiba laptop

  Hi, I just bought the 7.10.18 are now available for computers laptop toshiba-no, but feel what seems to be a bluetooth connection problem: when I play music or a bt transmitter connected to a stereo player or a motorola headset sound is interrupted during 1 second every 4 seconds - the problem is not related to the bt device as it appears on 2 different (transmitter + headset) devices , or his source that the problem occurs with streaming music (via wifi) and a CD of music played on my laptop (CPU 2.2 GHz + 32 bit Win7Pro)...
  Any help is greatly appreciated!
  (btw, does anyone know of a formal support / helpdesk for a bt-stack PURCHASED license?)

  What headset motorola model do you use?
  It is fully charged?
  What is your distance between portable headphones during the operation?
  Do you use an any other bluetooth devices at the same time?