Problem with port for network WRT400

Similar Questions

• Problems with drivers for laptop HP650

  Hello

  I have a problem with drivers for this model.
  I have installed windows 7 32 bit, then removed all the drivers from the official website of HP, but a problem with the two drivers, PCI SIMPLE COMMUNICATIONS CONTROLLER and CONTROLLER ASSISTED, now I can't connect to Internet, LAN or wireless internet.

  Is there a solution?

  

  Hello:

  This is the driver you need for the PCI SCC.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5225011&prodNameId=5225013&swEnvOID=4062&swLang=13&mode=2&taskId=135&swItem=ob-104656-1

  In order to find the right driver for the wireless card (since there may be one of several different model wireless cards in your notebook), go to Device Manager and click on the network controller needing drivers and display the material for her ID.

  If you don't know how to find the hardware ID, please read the info on the link below:

  http://www.DeviceDriverFinder.com/blog/device-drivers/how-to-check-the-hardware-ID-for-a-Windows-device

• Error message: a problem with your wireless network card

  Hello, I get this message as shown below: any ideas how to solve this problem? A problem with your wireless network card

  Your wireless card has stopped working properly.

  There is a network adapter that allows your computer to connect to a wireless network.

  To find out if a version update of your wireless network card is available, contact the manufacturer of your device or computer.

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.

  See you soon.

  Mick Murphy - Microsoft partner

• I have a problem with the wireless network card.

  Hello

  I use a laptop Medion MIM 2210 and I have a problem with my wireless network adapter.

  I get a message before Windows 7 starts telling me that there is problem with a wireless driver. The exact message says:

  "Intel UNDI, PXE - Z.0 (build 082)

  Copyright (C) 1997,1998,1999 Intel Corporation

  VIA Rhine II Fast Ethernet Adapter v2.43 (2005/12/15)

  PXE - E61: Media test failure, check cable of

  "PXE - MOF: exit Inel PXE ROM.

  This message appears every time you start and I don't know what he means by "Media Test Failure".

  I turned on my laptop today and noticed I had no internet connection, it showed that it connected but with yellow '!' symbol indicating that it was not fully connected. He did this for a while now and I have reinstalled Windows, in safe mode and I tried to delete the drivers and re - install, but it hangs right on uninstall what makes me angry no the case.

  Of course now, I tried to look for help my internet connection is running but the message is still there. Can someone tell me what to do or how to solve this problem, I am standing now on what to do. I was also on the drivers Medion website but it is impossible to navigate around and drivers without end there'e to choose. I would consider ringing them and asking them if they were not located in Germany as it would cost me a bomb! I did just now searching online via the Device Manager to see if he can find an update for the drivers but nothing came.

  Thanks for any help that anyone can offer :)

  The message is to be cause the BIOS looking for boot from LAN (not wireless) before it starts and then from the hard drive. The Media test failure is because to boot from LAN it tests to see if the wired Ethernet is connected, it is not if it generates the error message.

  Enter the BIOS press F2 after initial power on but before the Logo Windows shows

  Integrated devices should allow you to set the settings of wired network adapter. According to the BIOS it is either "enabled with PXE" or have another option to enable or disable the boot ROM

  In the boot options the LAN card should be removed altogether.

  This message is ONLY applicable to the transfer of the BIOS boot process and should have no impact on the problems of WiFi (it is not on WiFi)

• Having problems with ports USB 3.0 in computer option H8 - 1010 T

  Well, I bought the option USB 3.0 ports on top of the computer on the computer mentioned in the Thread object and I have problems with them.

  I tried plugging USB 2.0 devices in these two ports to "test" to see if they work, yet I am not able to get them to work with USB 2.0 devices. USB 2.0 is not compatible with USB 3.0 ports? Or I'm doing something other 'evil' here?

  Unfortunately, I do not have a USB 3.0 device to plug USB 3.0 ports to make sure that it is certainly a problem with ports still.

  The device in question I've tried in the USB 3.0 ports is a Microsoft Wireless Mouse 6000 wireless receiver. If the ports are not connected correctly, I would have assumed that the wireless receiver would have "blown" when I plugged it in, but it still works very well.

  USB 2.0 devices are not compatible with USB 3.0 ports? I know that USB 3.0 devices are backward compatible with USB 2.0 ports (I have a friend who is in this situation), but I also thought that the opposite was supposed to be true as well. Am I wrong?

  @William

  Check out this thread, seems to be the same problem you are having.

  http://h30434.www3.HP.com/T5/desktop-hardware/USB-3-0-ports-on-Pavilion-HP8-1070t-not-working/m-p/792857/highlight/true#M35248

• problems with updates for Windows (for Win XP)

  I have problems with Windows (for Win XP) updates...
  (1) I installed the hardware updates for my sound card (via Windows update) and now I can't hear the music through my speakers or headphones.  In addition, related to my sound card software do not work either!
  (2) at the same time, I tried to install Microsoft .NET Framework 1.1 Service Pack 1 through Windows Update and that would not install (.. .and I tried several times).

  So to rememdy those issues, I tried for hours to use the system restore, but whenever I've tried I'm not able to successfully restore and I tried several unique restore points.
  Any suggestions?  I spent hours on it, and nothing seems to help!

  Hello hoke, welcome.

  1. What is the brand and model of your computer?

  Let us know if it works:

  1. download the .NET Framework here cleaning tool:
  http://blogs.msdn.com/astebner/attachment/8904493.ashx

  2. run the utility and remove all versions of the .NET Framework
  3. restart your computer

  ---
  After the reboot
  ---

  4. download the .NET Framework 3.5 from here:
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=333325FD-AE52-4e35-B531-508D977D32A6&displaylang=en

  5. next, restart your computer

  Let us know if it works,

  Thank you! Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem with pdf for the opening of the health gov Web site.

  Problem with pdf for the opening of the health gov Web site. I use my ipad in Safari and have installed the application to adobreader. Healthcare gov support only suggested to disable the pop-up blocker. I did, and I couldn't always open the file. No problem on a desktop computer regardless of the browser.

  In my view, they spend on their web server to a document ECM server authentication. Someone else has the problem?

  I tried the Penguin, Chrome and Atomic browsers on the ipad and the same issue.

  Thank you!

  Keren

  Okay, actually, I think that there is a problem with the type of form. It is a form of a special kind (called a form XFA or Designer, for what it's worth), which can be opened with Adobe Reader and only on Mac or Windows. There is no iPad software that can read these.

• Satellite Pro L10 problem with Ports COM/Hyperterminal & Bluetooth

  Hello
  I have the following problems with the above machine:

  (1) I have attached an external series COM port to the machine. However, I can not connect to the COM Port using Hyperterminal.
  (2) I installed a Bluetooth USB adapter, but I can't view the protocol configuration.

  Each of the above works perfectly with another laptop that doesn't have a Bluetooth or even a network card.

  Everyone has experienced similar problems. I use WinXP SP2.

  Thank you

  MC

  Hello

  1, in which is the external COM port connected? Is detected in a straight path in Device Manager? What is the error msg to Hyperterminal?
  When connected via PCMCIA, try to change the settings for PCMCIA slot in the BIOS!

  2, try to reinstall the Toshiba Bluetooth stack! There may be some problems. The MS Bluetooth stack does not work properly with the Toshiba devices and one of the earlier Toshiba Bluetooth stack is not signed by Windows XP Service Pack 2!

  Hans Bye

• Problems with ports ethernet E4200

  I have problems with my ethernet ports on my router E4200 V1.  I do not get on flow rate of 12 Mbps on a single connected wired computer.  If I replace it with a simple switch 5 port I get 60 Mbit/s using the same cables.  I looked through the creation and cannot come up with any solution.

  Any help would be greatly appreciated.

  Thank you

  Mike

  OK I tore across the network.  Started from scratch and found the problem.  It is quite strange, but everything works fine!

  I discovered through the process of elimination that the cisco router did not like my Panamax Lan UTP.  Cisco is apparently more strict with the signal than the simple switch or refurbished netgear router.  I had the protection on the power strip 6 Max near the iMac.  The totally weird part is that slowed down the entire network.  Streaming is now pending on 60Mbps at each connection to the local network.

  Thank you all for your time I walked through this weird problem.

  Mike

• Toshiba Tecra A3 - problem with Port Replikator III

  Hello

  I have a problem with a Toshiba Tecra A3 combined with a Port Replikator III. Both work very well together until you disconnect the laptop computer. After you start the Toshiba Tecra A3 without the Docking Station, everything is always ok. But when I anchor again and start it, Win XP is not able to display the logon session on the external monitor screen. All configurations, I did (for example only display on external monitor) with the mobile extension module are only available after login. But when I don't see the logon screen, I can't do that; (o). so, does anyone have a solution how can I use the external screen after the boot (without using the FN + F5) key.

  any help is much appreciated
  Thank you
  Mario

  Hello

  As far as I know logon window can be displayed on the primary monitor only. Computers laptop LCD is set to a primary, and it cannot be changed. As you can see this option is grayed out in display properties.

  Good bye

• Is there a problem with Skype, for now?

  Hello people.

  I run a G4 and 10.411 using an older version of Skype with a software patch that I found in one of the Skype topics on this site. It has been working fine for months. I do not use only audio video. I have a subscription to call land lines. The problem I have is that I can call and hear the person I called, but they cannot hear me. Is there a problem with Skype today? Or they made changes from today that do not allow to use the patch and an old version of Skype? Any information would be appreciated.

  I just found out that there were internet problems yesterday and today. According to me, which may have been the cause of my problems from Skype. Here is the response I got from my ISP tech guy when I sent him to see if there are problems of the internet this weekend: 'Yes. There was a routing problem beyond our network or upstream suppliers. »

• Satellite Pro A100 - problems with wireless lan networks

  Hey all,.

  I have a problem with my laptop. It is able to connect to a wireless lan network, but is not able to properly - use this conection means: he do not get connection to Web sites or download data...
  I already have the latest drivers, but it's not helping...
  You have an idea? Could this be a problem with my wireless LAN card? What can I do?

  Thanks in advance

  DOM

  Have you tried a BIOS update?
  This you will find also on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com

  You have disabled all the security features for testing?
  I mean hidden SSID, MAC address filtering and so far. Maybe that's the problem.

  Check also if the router has the new firmware. You can find it on the site of the factory

• Problem with connection for ePrint

  Hello
  
  Today, I brought a new printer - all in one, HP Deskjet INK Advantage 3520. All functions are OK, but I have a problem with ePrint.
  In practice, the printer is connected to my wifi at home and I can print without USB cable with no problems. But when I want the ePrint of installation function, I get an error that the printer do not have any internet connection and I can't complete the configuration of the service.
  
  Do anyone know how I can eliminate the problem?
  
  Thank you
  Denis

  Hi DenyKr,

  I see that you are having problems with your printer, connecting to web services.  I would like to try the following steps.

  1. open the internet browser type printer IP address.

  2 should bring you to the status of the printer page.

  3. Select the tab network at the top.

  4. left side select IPv4 under wireless.

  5. under DNS address Configuration select manual DNS server.

  6. for favorite enter 8.8.8.8

  7. for alternate enter 8.8.4.4

  8. Select apply. You can get a warning saying that this could break the connection which is very good.

  9. turn the printer off for about 30 seconds, then try again.

  Let me know how it goes.

• Problem with wireless - Vista Network and Sharing Center does not recognize my connection!

  I use the Home Visa software and my network and sharing Center does not recognize my connection but I can access the internet without any problem. Previously, I was using a wireless router Linksys with an old box of AT & T internet with no problems. The problems started after I updated my AT & T internet box that made obsolete the linksys router and now the network share does not connect. I just have the problem of getting the network and sharing device recognizing that I am actually connected to a wireless network. I can't use my printer or share files with other people. I can't get my wireless printer to work if I restart my computer and I have the documents I want printed already sent to the printer. My network and sharing Center also works very well for a few seconds when I start my computer then it turns off again.

  Hello

  Method 1:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  You can also view the related items for more information.
  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Method 3:

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

  See also:

  Connect to a network with Windows Vista wireless

  http://TechNet.Microsoft.com/en-us/library/bb878035.aspx

• Problem with Port Forwarding (When PPTP is upward) in the WRT-160N

  Hello world!

  I'm looking for more help with Port Forwarding in my new Linksys router. I bought the daysago afew router and was pretty surprised when I discovered that there is no DD - WRT firmware is installed in it (the router was 100% NEW when I bought it). I downloaded latest firmware original and flashed Linksys file successfully.

  But I still have the problem (even that I was on DD - WRT firmware too) with the port forwarding for my DC ++ and Vuze (app from torrents): I wrote port forward for ports 49151 (for Vuze) and 4000 (for DC ++) to pass on to my desktop computer (IP 192.168.1.201) - I saw a post on this forum, that there could be a problem If you transfer to an IP address, which is within the local area of DHCP, so I forwarded to IP.201 (my local DHCPzone is 192.168.1.100-. 149) But does not forwardind (())

  What's wrong?

  My configuration:

  Router IP: 192.168.1.1

  PPTP (I my ISP)

  IP address: 192.168.226.127

  Default gateway: 192.168.226.2

  DNS 1: 192.168.1.1

  2 & 3 DNS: 0.0.0.0

  The IP address of the PPTP server: 192.168.226.2

  User name: *.

  Password: *.

  _____________________

  Simple Port Forwarding:

  Name of the external port application port internal protocol for IP address Enabled

  Vuze 49151 49151 times checked 192.168.1.201

  DC 4000 4000 checked two 192.168.1.201

  As you mentioned in your post that your ISP has provided you with a PPTP connection with an IP address: 192.x.x.x. The IP address that is provided by your ISP is in a private beach, and if you try to transfer all the ports on your router, it will not work, as long as your ISP modem is blocking this port. If you need get a public IP address from your ISP.

  As you get Private IP of your ISP, if this connection is called as NAT behind NAT and your Modem behaves like a router.

  So now you have 2 options, get the public IP address from your ISP or change the type of connection.