Problems of synchronization of time in VMWare Workstation 10

Similar Questions

• Problem with keyboard Windows 8 on VMware Workstation 8 + start error!

  Hello

  I installed VMware Workstation 8 today to use Windows 8 Preview developers. But I have a problem.

  When I finished with the installation of Windows 8 I can't type anything. When I go to settings, the settings said: VMware keyboard driver is not installed on the host computer. How can I install it?

  EDIT: I had another problem. When I want to launch Windows 8 I get an error: the VMware authorization Service does not work.

  I can get 2 answers please?

  Thank you!

  Post edited by: MrMvanDoorn

  Install the keyboard on a Windows host, improved driver read page 130:

  http://www.VMware.com/PDF/WS80-using.PDF

  To start the VMware authorization Service: services.msc open with window to open the properties of privileges, select VMware authorization Service, administration and press start button.

• How to solve the problem of VMWare Workstation 8 - unable to open/dev/vmmon

  Initially, I had this problem in March 2011 after installing VMWare Workstation 7 on a lab machine 5.7 RHEL and attempt to boot an image I know was good and should work. .  Someone else fixed the problem for me - I think they had to install a new/different libraries (vmmon.o and vmnet.o for vmware).  However, I find no information detailing what has been done to solve the problem.

  I see the same error on the same machine after upgrading to VMWare Workstation 7.0 for VMWare Workstation 8.0.

  1 here are the mistakes I see:

  a. "Could not open/dev/vmmon.

  b. "failed to initialize the surveillance apparatus.
  c. "cannot change the power state of VM: cannot find a valid peers to connect to.

  Also, when I run the stop etc/init.d/vmware, then run /etc/init.d/vmware start, I see that the State of "Virtual Machine Monitor" is DOWN.

  
  2 here is the information on VMWare Workstation:

  VMWare Workstation 8.0.1 build 528992

  3 here is the RHEL uname - information for the host:

  2.6.18 - 274.7.1.el5xen Linux #1 SMP xxx.xxx.xxx kills Oct 17 12:06:22 EDT 2011 x86_64 x86_64 GNU/Linux
  Release of RedHat Enterprise Linux Server 5.7 (Tikanga)

  The problem could be that the version of vmmon.o and vmnet.o that comes by default with vmware does not work with linux kernel version I have on my system.  I think I need to build a new vmmon.o and vmnet.o on my particular 5.7 RHEL.

  I found that to build a new version of vmmon.o you Executive vmware - config.pl.  I have not just on my machine, and I was not able to find on the internet.

  Here is the version of vmmon.o (for RHEL 5) that I have installed on my machine:
  /usr/lib/VMware/modules/binary/BLD-2.6.18-8.EL5-x86_64smp-RHEL5/objects/vmmon.o

  Here is the version of rhel5 I use:
  2.6.18 - 274.12.1.el5xen
  It is possible that the vmmon.o using bld - 2.6.18 - 8.el5 - x86_64smp-RHEL5 is not compatible with the kernel 2.6.18 - I 274.12.1.el5xen.

  Please help me find vmware - config.pl so I can build my own vmmon.o and vmnet.o

  do not use a kernel XEN enabled when you install Workstation

• Impossible to disable the time synchronization in VMWare Workstation 8.0.1

  I read 1189 KB # as well as various articles on disabling time synchronization between host and guest, but I can't seem to stop synchronization.

  I closed the comments and edited the VMX file as follows:

  tools.syncTime = "FALSE".
  Time.Synchronize.continue = "FALSE".
  Time.Synchronize.Restore = "FALSE".
  Time.Synchronize.Resume.Disk = "FALSE".
  Time.Synchronize.Shrink = "FALSE".
  Tools.Synchronize.Tools.Startup = "FALSE".
  

  But no matter what, the time of comments still synchronizes to the host after turning the power on or return to.

  I tried on the hosts Windows 2008 x 86 and Windows 2008 R2 with the same results.  I also disabled the functionality of Windows to "synchronize with a time server Internet.

  I'm using VMWare Workstation 8.0.1 on Windows 7 Pro x 64.

  Clues as to what I'm missing?

  Thank you.

  Your initial message, I found that something is different with the content of KB.

  Will keep you ' tools.synchronize.tools.startup = 'FALSE' but the KB said there should be time.synchronize.tools.startup = 'FALSE'.»

  Please copy and paste below your *.vmx file model.

  tools.syncTime = "FALSE".
  Time.Synchronize.continue = "FALSE".
  Time.Synchronize.Restore = "FALSE".
  Time.Synchronize.Resume.Disk = "FALSE".
  Time.Synchronize.Shrink = "FALSE".
  Time.Synchronize.Tools.Startup = "FALSE".
  Time.Synchronize.Tools.Enable = "FALSE".
  Time.Synchronize.Resume.Host = "FALSE".

• Problem installing Windows on VMWare Workstation 11 10

  Good evening

  I'm a french user on VMWare.

  I have a problem when I try to install Windows on VMWare Workstation 11 10, I'm stuck here:

  

  I tried several times to reinstall.

  I use this iso standard: Windows10_TechnicalPreview_x64_FR - FR_9926.iso

  Can you help me?

  See you soon.

  Set up 2 x 2 cores CPU and memory: 3 GB

• I have a problem starting up a Windows XP Pro Machine virtual Windows 8 host system (which has VMware Workstation 10.1).

  I am new to the virtual machines.  For several months I've been running a Windows XP Virtual Machine in an old machine of Windows 7 with VMware Workstation 7.0.  The hard drive is having some problems at times, so I thought that I could move the virtual machine on a new computer that has an OS 8.1 Windows and VMware Workstation 10.  For example, on the Windows 7 machine, I copied the directory with all the * .vm files and pasted into the machine to Windows 8. But when I tried to start VMware Workstation 10 in Windows 8 machine, I got the message "this virtual machine policies are too old to be run by this version of VMware."  I went to the knowledge base and used the solution described here: I've deleted the lines of three 'policy' of the .vmx file and added the suffix .ancien to the .vmpl file, which actually disabled.  Now, when I try to start the virtual machine, the black screen appears with the VMware logo in the Center and everything seems fine, but Windows XP starts.  And logo VMware guard churning away as in a continuous loop.  It is not easy to stop.  The only way to stop VMware is via the Task Manager or restart the machine.

  What must I do to get the Windows XP Pro VM to run in the new machine?

  VMWare technical support suggested that I have disable 3D acceleration (VM > settings > view and uncheck the box 3D graphics acceleration).  The virtual machine starts now with some minor problems, but it is usable.  But by closing accel 3D turns, in the words of the Technical Support Engineer, David, that there is "a problem with the graphics card not imitate or through its capacity to the virtual machine.  In other words do not support to the VM guest 3D acceleration. "My next step is to make sure that I have the updated driver for the Intel HD Graphics 4600 display adapter.

  Minor problems are:

  (1) the virtual machine works best in screen mode reduced.  There are a few problems speed mode full-screen.

  (2) the VM will still work after switching on of the host.  But after execution of the virtual machine, if power you the virtual machine and the release of VMware workstation, then later, start the workstation, the virtual machine will power not.

  To turn it on again you must out of VMware Workstation, disconnect the host machine and then reopen it in one.

• NAT with VMWare Workstation 9-Urgent problems

  
  Hello

  Try to use NAT in VMware Workstation 9 and am lost in my VM connection.

  But when I use the network bridge, it works very well.

  Is someone can you please help me solve?

  I tried reinstalling VMware workstation for all n No.. times and restored the settings of the Virtual Network Editor as well.

  Help, please!

  It seems that the client does not receive a DHCP address? Assuming that the virtual network adapter in the virtual machine settings is 'connected' (which, I guess, because you said Bridged works very well), you can check if there is a problem with the installation. Please run services. MSC (or net start from the command line) to see what VMware services are running on the host computer.

  André

• Network bridge in VMware Workstation 11 connection problems

  I have bridged network connection problems in VMware Workstation 11. So far I have tried:

  
  

  Re: Windows Pro/Ent 8.1 Overview invited - stop Windows Net Performance, away from work

  
  

  Re: Flow very slow network-> Guest host, but no comments <-home

  
  

  So far, none of the solutions worked. I turned off "Large Send Offload" on each adapter that I could find on the host and the guest. Nothing. Restore these settings in any combination with other out does not work either. I edited the .vmx file and replace by vmxnet3 occurrences, and that no longer works. So far nothing I've tried has worked. I disabled all firewall and antivirus. Still nothing. When I run Guest OS Windows Network Diagnostics, I get the "your modem broadband has connectivity problems." However, I know that this is not the case. I also used the "Virtual Network Editor" to force the bridge connection to select the correct network card (in my case, it's the Intel Centrino Wireless - N 1030 wireless card), but still no luck. Any help would be much appreciated.

  
  

  Thank you

  Dave
  

  
  

  My Stats:

  
  Host:

  OS: Windows 7 x 64

  Processor: Intel Core i7

  Installed memory (RAM): 16.0 GB (15.9 GB usable)

  Wireless adapter: Intel Centrino Wireless - N 1030

  Router: Netgear AC1200 Smart Wifi router. Model: R6200v2 (default settings)

  
  

  Comments:

  OS: Windows 7 x 64

  
  

  So I finally the solution look. BitDefender firewall was blocking all traffic on the connection Bridged in VMware Workstation. I have disabled the firewall completely Bitdefender and Bridged Networking worked perfectly. I'll probably create another topic more precisely around Bitdefender firewall configuration to allow traffic network through Bridged from VMware.

• USB foot pedal problem (Infinity IN-USB-2): recognized by Windows but does not work on VMware Workstation 10

  When I connect an Infinity IN-USB-2 pedal for my guest Windows 7 Professional (on Ubuntu 14.04 and VMware Workstation 10.0.2), the pedal gets recognized by Windows and different applications, but by pressing the pedal itself has no effect.

  I downloaded a USB foot pedal Tester (http://vec-infinity-in-usb-1-foot-pedal-tester.soft112.com/) on the client and he acknowledged that the device is connected, but when I pressed on any of the three pedals, the tester has not detected the presses.

  I tried the pedal on a real Windows computer, and it worked fine.

  When I connect the pedals, even with the guest in the foreground, VMware Workstation will appear a dialog box:

  The specified device is claimed by another (usbhid) driver on the host operating system. The device can be used. To continue, the appliance will be first disconnected from its current driver. [Cancel] [OK]

  When I click 'OK', we state above: Windows recognizes that the device is connected, but foot-presses are not detected. My other USB devices are not pop this dialog box. (Click Cancel maintains the device disconnected from the guest.) I don't know if the dialog box is significant or a red herring.

  Here's what/var/log/syslog says when I connect the pedal with the Windows client in the foreground:

  kernel: [281434.822751] usb 2 - 1.7: new low speed USB device number 28 using ehci-pci

  kernel: [281434.920667] usb 2 - 1.7: new USB key found, idVendor is 05f3, idProduct = 00ff

  kernel: [281434.920672] usb 2 - 1.7: new USB device strings: Mfr = 1, product = 2, SerialNumber = 0

  kernel: [281434.920675] usb 2 - 1.7: product: pedal WITH USB

  kernel: [281434.920678] usb 2 - 1.7: manufacturer: VEC

  kernel: [281434.923852] entry: CVE CVE USB pedals as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7:1.0/input/input38

  kernel: [281434.924239] is hid-generic 0003:05F3:00FF.0016: entry, hiddev0, hidraw3: USB HID device v1.00 [CVE CVE USB pedals] on usb-0000:00:1d.0-1.7/input0

  PSG-probe: check the bus 2, device 28: ' / sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7 '.

  PSG-probe: bus: 2, device: 28 is not a MTP device

  And when I click on "OK" to the dialog, he said:

  kernel: [281480.324926] usb 2 - 1.7: reset low speed USB device number 28 using ehci-pci

  kernel: [281480.900448] usb 2 - 1.7: reset low speed USB device number 28 using ehci-pci

  When I unplug the device, it is said:

  kernel: [281517.582472] usb 2 - 1.7: unplug USB, the device number 28

  Thanks for the ideas on solving this problem.

  Answering my own question: I spoke with a salesman who told this pedal does not work on virtual machines for the following reason:

  These pedals are all just Universal USB controllers that require programs or applications to be able to see and recognize them for use. Because they are installed by the base of Windows and Generic USB devices drivers, they can not be seen my remote computers via USB sharing etc.

  They recommended using a hotkey program to work around the problem. I have not tried this solution, but bought a different pedal that works out of the box with VM: a vP-1 vPedal. Lower build quality than infinity (in my opinion) but it works perfectly.

  This is the idea of the key of the seller:

  I have a solution that will allow you to use the pedal as expected if the remote program who need to use supports the use of shortcut keys. For example, these pedals are commonly used with NCH Software Express Scribe professional software. This software can use either a pedal, or you can assign the playback functions to access keys. In the scenario you are talking you re Express Scribe on the remote computer to use keyboard shortcuts, you then install Pedalware (http://www.altoedge.com/pedalware/index.html), a free Windows only the foot pedal utility made by NCH Software, you then use the Pedalware utility to assign the buttons on the pedal of a keyboard shortcut that coincides with those remote program.

• Networking question in VMware Workstation / nested ESXi network configuration problem

  Hi guys,.

  I am trying to set up a virtual lab, I setup a domain, a vcenter server and up to 1 ESXi host controller.

  I am really struggling with the network aspect in establishing a vmnic for storing shared, please see the attached screenshots and a few questions:

  1. Is a vmnic a real network map? or vmnic correspond to "network adapters" that you put in place since the setting of your virtual machine?

  I followed a tutorial and implement 3 NICs on the ESXi host, in Bridge mode, I tried this in my configuration of vmworkstation and I lose the connection to my server vcenter to the ESXi host.

  See screenshot attached to how I configured my ESXi host, screenshot is called 'screenshot2esxihost network', I run got each of the maps defined on NAT network.

  

  See also the screenshot of how I have my configuration of network settings in my VMWare Workstation, screenshot is called "screenshot1. the tutorial does not show how it has its editor of the virtual network configuration, but it puts its ESXi host NICs in BRIDGED mode, and I'm guessing that you can set this time within the virtual network adapter. If someone could tell me what changes should I make in there and on the network cards in my ESXi host, which would be really useful.

  

  My domain controller, server ESXi hosts and vcenter are currently on the 192.168.86 range, which currently stood at NAT

  See also a screenshot from the vsphere client - I don't see a vmnic "vmnic0", my goal is to be able to add a "vmnic2" for a separate storage network.

  

  any help would be received with gratitude, I VCP510 review at the end of the month and really hope to be able to get my lab setup as soon as possible.

  The vmnic is the rising 'physical' of an ESXi host. So with the 3 network cards that you configured for the host in VMware Workstation you will see under "Network adapters" and you can use them to vSwitches in the section "network".

  André

• Problem with VMWare Workstation combo, .vhd virtual drives and physical disks in the sector of size 4K?

  All,

  I suspect something wrong with some of my virtual machines.  I have been using these virtual machines for a while, and I see some weird behaviour recently.

  I see a lot of corruption in the virtual hard disk (.vhd based).  CHKDSK automatically gets performed many large files such as Oracle datafiles get damaged etc...  It all seems quite random and inconsistent, but I am using .vhd virtual machines in VMWare Workstation for years without problem.  This problem is new, and hard drives are basically unstable.

  I * think * (and I'm totally off base) that is perhaps the issue with my new external hard drives.  These discs have a 4 KB sector size, without e512.  Thanks to this architecture of hard drive, don't mount not the tools of Microsoft or manupulate .vhd files on these disks.  The questions seem to go away if I switch to vmdk or switch to the physical hard disk size-one-sector 512kb.  Because errors are not compliant, that I don't really have a way to document/prove that is the case, but it seems to be.

  I use version 9.0.0 on Windows 7 Workstation, and the guest is Windows Server 2008R2.

  My question is:

  (1) what meaning?

  (2) how I prove/document, since it is a contradiction?

  (3) is this a known problem?

  (Btw, switching HDD's vmdk is not an option in our case due to an obscure legal agreement with Microsoft.  I have to distribute my VMs in vhd format, even if they are designed to run on VMWare...)

  -> Adam

  These discs have a 4 KB sector size, without e512.

  (I've highlighted "without e512" in "BOLD" to key in my answer to the host operating system.)

  -L'OS is Windows 7 Enterprise

  According to the political support for the 4 K sector hard drives in Windows, Windows 7 does not support the native 4 K (logical 4 k sector size) but it does not support Advanced Format or 512th (size of logical sector physical and 512 bytes of 4 K) and that is can be the question.

• Problem installing VMWare Workstation on a Server Windows 2012

  Hello

  I have problems when trying to install VMWare Workstation on a Server Windows 2012. Windows Server is Amazon EC2 environment and a generic image extended release.

  The problem is that the installtion process fails because of "Hyper-V" during installation, but after investigating the option "Remove roles and features" I can see that it is not installed.

  Is there any fixes for this issue?

  I enclose three screenshots for you pleasure.

  Regards, Ray...

  Hello Ray,

  Welcome to the VMware community forums.

  You run an EC2 instance that has just 615 MB memory installed?

  It's kind of a weird for a host, much too low for Amazon memory configuration, even be profitable.

  I think that your server is running UNDER Hyper-V, for example. It is probably a Virtual Machine.

  You can easily check that yourself by running the script from this site:

  How Hyper-V to: detect if you are inside a virtual machine

  If it's a Hyper-V virtual computer then I don't think you can install VMware Workstation on the virtual machine and run the nested clients.

  You could do the opposite (invited running hyper-V in a workstation virtualized on vSphere) but is not very fast.

  As you have no control over which platform virtualization Amazon use for their windows servers, I'm afraid you will have to go for a dedicated server instead of a virtual machine.

  Hope this helps,

  --

  Wil

• Problema al add UN nodo adicional al Cluster Windows Server 2012 con VMware Workstation 9 en

  Hola Buenas,

  Ante todo decir este are a Québec fallo he revisado y las responses in different los don't post han well para help me, good os.

  El caso are that I have 2 servers DELL PowerEdge R420 fisicos identicos, cada uno con ellos 3 VMs sober instaladas VMware Workstation 9. The first virtual machine are an image of Kerio control, a second virtual machine to Windows Server 2012 con dominio Controladora, is the third VM con WS2012're donde quiero crear el cluster con dominio usuario. ESTOS servidores knew vez esta una cabina data via iSCSI connected.

  Add tambien when performed the tests of validation led Cluster, todo lo tengo OK. El caso are so creo el cluster con el Nodo 1 y 2 Nodo (sugar Québec cada uno fisica Máquina distinta ellos y bajo mismo Dominio) me error UN da has the el crear hora cluster. In cambio, if creo el Cluster con este nodos if any to crea, pero el fallo viene a hora of connect UN nodo adicional (ya sea o 1 Nodo Nodo 2). Este fallo viene cuando el nodo TR checks are completely funcional in el Cluster, is is "pensando" y da fallo por tiempo sold.

  He revisado problemas similar y he visto that el antivirus can be una causa e caso no lo're are only aun no he wont any AV... There comprobado red devices (utilizamos 4, 2 iSCSI, 1 red LAN y otra heart rate), he desactivado los red el protocolo IPv6 devices, he probado connect los nodos con el Kerio Offline, el desactivado firewall of Windows, exportar components del registro TCPIP6, capture las conexiones iSCSI...

  El cluster is as en Máquinas Office instalacion del WS2012 y is ha hecho manera person, no mediante VMWare del injerto.

  Una nueva prueba as hoy he ha hecho sido realize el cluster 2 maquinas office in una misma Máquina física y to ha s con exito, pero cuando intento realize el 2 nodos cluster (2 machines virtual cada una fisica diferente Máquinas) cuando me da el error. Esto deduzco raiz Quebec are a VMware o red, no lo o problema se, he probado use tan solo 1 switch (infrastructure utilizaria 2), changing IPs, pero igual sigo as can be? contacts? Alguna especifica VMware config?

  El caso're llevo several days ago that don't con este problema y no se a what can deber, agradeceria muchisimo the the comunidad ayuda.

  MUCHAS Gracias

  Buenas

  Between 2 workstation are posible realize ese tipo configs of forma limpia.

  El problema're (sniffer lo of UN pones veras TR), Los nodos assume ip-spoofing y arp spoofing cuando salen por tarjeta of Red led host.

  Para hacer eso as pides, deberias workstation pasar an esxi.

  Saludos

• Problem with the Installation of VMWare Workstation 8

  I got this error when installing VMWare Workstation 8

  How can I solve this problem?

  

  Whether or not, it gives me this

  

  and then nothing happens

  Looks like your way of temp has 2 problems - firstly, it is quite long; Secondly, there is a strange character in.

  Try changing your environment a simple C:\TEMP or C:\Windows\Temp folder variable.

• Problem downloading the components of VMware Workstation

  Hi, I use VMVware Workstation v 7.1.2 build 301548 on a Windows 7-64 bit SP1 Workstation.

  I have no problem with my Internet Explorer to connect to the Internet via the proxy (ISA 2006) on port 8080.

  If I try to install VMware tools in a new virtual machine or if I try to "Download all components now" I get only a popup with

  -VMware Workstation connects to the update server

  -Update Server: https://softwareupdate.VMware.com/CDs (which is no problem for my Internet Explorer to this site)

  -Proxy server: http://visa06:8080 (which is correct)

  -State connection: connection...

  But it never ends. Any log file to check?

  On my ISA Server I see the following:

  ERROR_SUCESS 0X0

  0X800074E21 FWX_E_ABORTIVE_SHUTDOWN

  No idea what is the problem?

  If you have a licensed copy of connection workstation to your account and download Vmware WS 7.1.3 fo your Linux or Windows platform.  For Linux, download the full .bundle file.  It includes all the tools.  If this isn't the case, you don't need to download an eval copy and leave there a license.

  Marty