Problems with tdms built executable; memory.cpp write error

Similar Questions

• Equium A60 with defective built in memory

  Hello

  I tried to recover my Equium A60 with the recovery DVD and it does not boot to windows. I tried to install a number of different versions of windows and the error messages lead me to the conclusion that the module memory is faulty. The system came with 256 MB of memory and it is hard because it is part of the motherboard. My question is if I buy a memory module and install it in the expansion slot will be it be prevented from working by the faulty memory?

  Post edited by: binkey1st

  Hey Kevin,

  There is unfortunately no way to isolate the faulty RAM on your motherboard. Even if you install a second module of RAM the system always tries to use the built in so defective module.

  You will need to take you laptop to an ASP for the defective replace module.

  Kind regards

• problem with a block of memory in labview 2009

  Hi all

  I have "ERROR: MapLib:979 - LUT4 symbol" during the compilation process (lots of errors like this), and I discovered that the reason of my problem is block of MEMORY.

  To be sure that the problem is in this block, I did a very simple project in LabView 2009 (on FPGA Target PCI5640R) only with the use of this block you can see in the photo, as well as in file test_memory block.lvproj attached link: https://www.dropbox.com/sh/u87f1oihelmm4dq/Jo_6-bICSf

  

  I have a problem with compiling VI with this block, and I have so many errors like:

  ERROR: MapLib:979 - LUT4 symbol
  "window/Thatcher/n_00000036/nSCTL_00000013_00000014/n_000000A3/cOutLoc<0>1.
  (output = window/Thatcher/res000001ed_wi<2>) is the input signal
  "window/Thatcher/res0000020d_wo<1>" that will be deleted. See Section 5 of the
  Map a report file to find out why the input signal will become conveyors.

  or

  ERROR: MapLib:978 - LUT4 symbol
  "window/Thatcher/n_00000036/nSCTL_00000013_00000014/n_000000A3/cOutLoc<23>1.
  (output = window/Thatcher/res000001ed_wi<25>) is an equation that uses
  input pin I2, which no longer has a connected signal. Make sure that all the
  the pins used in the equation for this LUT are signals that are not cut
  (see Section 5 of the report file map for details on which signals were
  adjusted).

  Entire report, you can see in the file report.txt on the attached link.

  I would appreciate if someone could take a look at my problem with simple project and suggest me a solution.

  I'm really stuck with my biggest project which need to have this memory block.

  I'm looking forward to hear from you,

  King looks

  ING. Damir Hamidovic

  Hi all

  I find a sollution to my problem.

  In memory-properties-general-setting up, I changed the block to look up Table memory, and I compile memory.vi and run it successfully.

  I did change as you can see on the picture:

  

  Just, can you tell me is it all "bad properties" and limits the use of this type of memory (Look up Table) of the implementation?

  King looks

• Problems with e250 and SD memory card?

  Basic information about the player: e250, 2 gig, version 1, 01.02.24 has

  Basic information on the SD card: Sandisk micro SD, 2 GB

  I have my sansa for a year and a half, and I have never had any major problems with it so far.  Recently, I had to remove the songs to put on the new songs due to lack of memory, so I decided to buy a memory card for it.  Getting the empty memory card I inserted and recognized my drive and everything was fine.  The problems started when I put songs on the memory card.

  I put my player in MSC mode (as indicated in the manual), it is hooked to my computer (windows XP), and everything was fine.  I used windows media player to synchronize music on the memory card, then picked up my drive.  It is restarted, as he should, and I went to listen to music I would put right on and yet once again, it was fine.  Then, I wanted to listen to my music, and he flipped out on me and wouldn't let me play it.  After determining that it was not just this song, I removed the memory card and tried to play the old music, but he would always let me.  A small red box saying 'Wrong way' just kept popping up.

  I decided to start over, so I have deleted all of the player (via the computer) and then attempted to deliver music on.  I tried a few songs, sync and play the two media of windows and my computer says that the songs were on the player.  To get the player from the computer, I went to "songs" and saw that it was always empty.  I hung up, and the computer says that these songs are on the player.

  In a nutshell: my computer says it is synchronization of the songs to the player, but in reality, it isn't.  This has only started to happen after I had the memory card.

  If someone could help me, that would be great.  Thank you!

  I don't think that Windows Media Player will work in players v1 in MSC mode. It must be in MTP mode for WMP to recognize. In addition, with the cards in players v1, you HAVE to add/remove music in MSC mode only by drag and drop from your computer to the card (read as a drive in Windows Explorer). You have to treat the reader and the card as the "separate entities", even if physically they are connected. Once music is on the map, the player will fit perfectly on both songs.

  In what concerns the "bad tracks", you need to run CHKDSK to repair corrupt files, so you can remove them properly. Answer NO when it asks you if you want to save the files "bad strings" (or something like that). Check the 'sticky' & the FAQ at the top of the body for specific instructions on running CHKDSK. While you're at it, also check out & play on your player of formatting, as you should probably next to you to go to a clean slate.

  I believe that files (songs) put on using WMP in MTP mode can ONLY be played in this mode, and MSC placed files using drag ' drop can be read in THAT mode, which can be part of your problem. Probably best to start fresh and then don't forget you must manually put the songs on the map in MSC mode.

  Another oddity of SD cards (at least with players of v1) is that you must also manually add the 'album art' to the file containing the music if you want to see the album art that song. With WMP and MTP mode on the player, it will play the album art embedded in the ID3tag. It will not do this on the SD card . You can see specific instructions on how to do it here. There is also a video showing the procedure here.

  I hope this helps...

• problems with the built-in spellchecker to ff 23

  I find and have checked through these forums, that the text boxes on web sites that are a single line are ignored by the spell checker. I'm working on a Web site, no I don't administer it, which has an input field which is a single line. This field is the only one I have problems with because it does not check the spelling. Anyone know of a way to adjust or replace the spellchecker, so he'll see this area as well. Thanks in advance.

  Have you attempted to set the pref 2?

  That should give you a checkbox "Check spelling" and a menu of languages in the context menu for a single line entry field.

• Problem with DPS built app sign in the process

  I'm running into a problem with the ios version of our DPS application.

  We build a right and iTunes subscription app.

  To try the payment custom, I sign in and out as many different users.

  A new installation of the application on the iPad, I connect as a user XYZ.

  Tapping on the machine shows the Disconnect option [XYZ].

  After Sign Out look, I'll then sign up as a user ABC.

  Tapping on the machine always shows the Sign out [XYZ] option.

  I expect the following Sign Out [ABC].

  
  

  Is this a bug? Know the cause? or I'm doing something wrong.
  

  This bug is a known issue. You can see the same problem in the ends of DPS when you connect (dps tips), disconnect, connect (bob bringhurst), and then sign in again. The original user is always displayed until the application is restarted. I don't know when this issue is scheduled to be fixed.

• Problem with the primary dns server, get the error "There could be a problem with one or more network adapters on this computer."

  Hello

  I was all of a sudden having problems connecting to my wifi at home. When I was diagnosed, he says cannot communicate with primary dns server. I tried all methods in similar positions, but nothing works. I am also unable to connect to internet with my iphone and the itouch. It's really frustrating, because I've already tried all of your suggestions. I just ran another ' diagnose connection problems and it says the following:
  "There could be a problem with one or more network adapters on this computer." Help, please!
  Thank you!

  Thanks for your help, but I have tried this before. In the end I just unplugged my modem and plugged in again and it worked? I feel a bit silly not to try first.

• I'm having a problem with my WiFi. I get an error of incorrect protocol bindings and the drivers are having problems.

  original title: Wifi is over now! That's happened!

  I had a problem with one in a one off wifi conection on my laptop? now I think that its output for good. I get the error of incorrect Protocol connections (TCP/IPv4/IPv6 LAN) and more adapters network realtek PCI family knows the material and pilot related questions. same spirit my atheros AR5007EG wireless network.   I ve herd, it could be just the problem of getting the last windows update and then its simple drivers on their own. Im confused wat should I do? It would be a great contribution to your fellow man is that you would direct me to another link that might help too!

  Hi Pandelicioso,

  It is sufficient to indicate the complete error message you receive.

  IP (Internet Protocol) link problems are usually caused by an out-of-date network adapter driver

  Method 1: to reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

  http://support.Microsoft.com/kb/299357

  Method 2:  Follow the steps mentioned in the link below

  I get an error message about Internet protocol (IP) bindings.

• I have a big problem with Windows Live essentials 2011. 0x8007064c error code

  I have a big problem with Windows Live essentials 2011.  I can't find in Add and remove programs or in C:\program files to remove it if I can reinstall it.  I went through the registry and deleted all instances of it.  When I try to reinstall, I get the error 0x8007064c code.  I've done everything I can find to do, but to no avail.  Help, please...

  Hello

  bad forums

  Repost in windows live forums

  http://windowslivehelp.com/

• After the upgrade to Windows 8, problem with teredo tunneling adapter says code 10 error and the device cannot start

  Original title: teredo tunneling adapter error number 10 on windows 8

  on my acer travel mate 6292 which I just upgraded to windows 8 pro recently got a problem with teredo tunneling adapter.

  It says error code 10 and that the device cannot start, it made me unable to use wifi on my laptop

  I tried to reinstall the driver but it just says: windows encountered a problem installing and he says its error code 10

  Please help me

  Thanks in advance

  Hi Samuel,.

  We appreciate your efforts to solve this problem. We will put all our efforts in order to solve the problem.

  Teredo is a tunneling protocol designed to grant IPv6 connectivity to nodes that are located behind IPv6 NAT (network address translation) not compatible devices. It defines a way of encapsulating IPv6 packets in IPv4 UDP (User Datagram Protocol) datagrams can be routed through NAT devices, on the IPv4 internet.

  I wish to inform you that Acer has not released Windows 8 compatible drivers for Acer 6292 travel companion.

  I suggest you try to install the drivers for the card wireless in compatibility mode and check if it works. Check out the following link to download and install drivers in compatibility mode.

  Make the programs more compatible with this version of Windows

  http://Windows.Microsoft.com/en-us/Windows-8/older-programs-compatible-version-Windows

  The link below to download the drivers for the wireless card: http://us.acer.com/ac/en/US/content/drivers

  A Code 10 error is generated in the Device Manager in one of the following situations:

  1. the Device Manager cannot start the device.

  2. one of the pilots who needs the unit does not start.

  3 device Manager has sufficient information to recognize the error that spread upwards by the device driver.

  We could try following common resolutions to solve the problem:

  1. update the drivers for this device

  2 launch a service of automated troubleshooting

  3 contact material supplier technical support

  For more information, please see the following article:

  FIX: "this device cannot start" error Code 10 in the Device Manager in Windows

  http://support.Microsoft.com/kb/943104/en-us

  In addition, this article could also be designated:

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-in/Windows/fix-network-adapter-problems#1TC=Windows-8

   

  Please answer us on the State of the question to help you further.

• a problem with an installation of memory

  Hello

  I have trouble to install memory in addition to my currnt one card.

  When I use the old one only it workes very well. When I use both my cmputer won't turn on. Instead, I hear 5 sound "beep". It lights when I use my new single memory as well.

  I want to know what I'm doing wrong and what I should look for in a memory if mine does not fit my computer.

  I use:

  Win7 starter

  computer pentium 4 32-bit.

  the memory I have installed on my computer is:

  DDR2
  512 MB
  PC-2 4300 (266 Mhz)

  the new memory I bought is:
  Kingston 512 MB DDR2 533 mhz pc2-4300 NON ECC Unbuffered Desktop PC RAM memory

  My motherboard model:
  HP-09f0h
  Since its an old computer, I have not found an answer to my problom.

  If you need more info, here is my cpu and motherboad info:

  motherboard Info

  CPU - info

  Thank you!

  Whenever you do an upgrade of RAM in the future and you want to it works as expected the first time it is turned on:

  Always purchase compatible memory modules guaranteed

  upgrade only pairs of identical memory modules.

  What you are experiencing, it's what I expected to happen because you do not follow these two rules "" upgrade memory in PCs and laptops. Mixing memory you made generally results in failure at startup or in an unstable operating system.

  I can't tell you what should work, because you have not identified your PC. This is not the same as upgrading a self built PC. Manufactured of PC memory upgrades are always executed by matching the name of the manufacturer of the model to the list on the site in the configuration utility or the manufacturer of memory by the manufacturer. Find a serial number on the side or rear. Post here the number of full product in the wire.

  If I want to add memory to my motherboard ASUS Crosshair V Formula-Z, I look in the manual of the motherboard memory compatibility list. It is quite different with a manufactured as your desktop PC.

• Problem with digital I/o read and write in CVI

  I have a PXI with PXI 6225 Renault installed box. For some uses, I wired 4 lines of digital port 0

  for its 4 top lines so that the output digital on bottom lines can be read as a digital input on the top lines.

  In the CVI program I have set up two input and output of tasks as follows:

  Enter task:

  DAQmxCreateDIChan (digitalInputTask, "PXI1Slot5/port0 / line4:7","InputLines", DAQmx_Val_ChanForAllLines ");

  DAQmxCfgSampClkTiming (digitalInputTask, ' AI/SampleClock ", 4000, DAQmx_Val_Rising, DAQmx_Val_ContSamps, 2000" ");

  Output task:

  DAQmxCreateDOChan (digitalOutputTask, "PXI1Slot5/port0 / line0:3","OutputLines", DAQmx_Val_ChanForAllLines ");

  DAQmxCfgSampClkTiming(digitalOutputTask,"ai/SampleClock", 4000, DAQmx_Val_Rising,DAQmx_Val_ContSamps, 2000));

  DAQmxCfgOutputBuffer (digitalOutputTask, 2000);

  I also started a task of analog input to ensure that the analog "IA/SampleClock" sample clock is running, and I check

  as I interpret the correct analog data of my analog lines.

  Here's the problem:

  I write 2000 identical samples of zero for the 4 lines (port0/$line0... (3) with the following command:

  DAQmxWriteDigitalU32 (digitalOutputTask, 2000, 1, 10, DAQmx_Val_GroupByChannel, sampleArray, & writing, NULL);

  After a while, I try to read the 4 lines (port0/4... (7) using the:

  DAQmxReadDigitalU32 (digitalInputTask, 2000, 10, DAQmx_Val_GroupByChannel, scanArray, 2000, & read_num, NULL);

  but the values returned in scanArray are nil!

  If I replace the digitalInputTask by digitalOutputTask in the above function call, I get the good samples rewritten

  (do not know how the 4 lines below that are configured in output mode can be read back! could it be just read buffer?)

  I don't know that the hardware configuration is correct, because when I try to emulate this feature in Labview, it works.

  (I use an output data acquisition assistant to write down the 4 lines of port 0, using a digital wave of entry, then)

  top reading 4 lines with the help of one Assistant DAQ to enter a digital waveform VI.

  In another test, I have 4 lines below in CVI, put on stop my CVI program, start a simple Labview VI to read from

  upper 4 lines and I can see the values I just write in CVI).

  Any idea what could be causing DAQmxReadDigitalU32 to read only zeros in CVI?

  I compared my settings in CVI with parameters DAQ assistant in Labview and tried to make them identical, but nothing helped.

  Thank you

  Try to use these examples to see if you can read and write in CVI

• Problem with 16 GB Sandisk memory card

  Hi all

  I just bought a Clip Zip and use a Sandisk memory card to use with it. Unfortunately, while most of the library, there are a few artists who don't. I tried moving them on the player's memory, and then they operate, so it seems to be a problem reading the card, rather than the tags of the files. I bought the card from Amazon, so I eliminated the possibility that it might be a fake card. Does anyone have any suggestions as to what may be the problem?
  Thank you very much for your help!

  How many records you on the drive? Keep inmind that the zip has a database of song 8000 limit. anything above 8000 will not be crawled and appear not in the menu. If you have less than 8000 files can you put some of the bad files so we can take a look?

• Problem with variables stored in memory/cookies.

  I'm not really sure what's going on, but that's what happens.

  I have a swf file that connects to a server through a file, but that seems to hold some variables in memory or something to make it works fine the first time it is loaded, when I load the page again, either the browser or the drive is not compensation on the previous values. I don't know if there is a way to ensure that the swf file when it loads ensures don't not to keep the values in the cache.  In fact, it seems that the only way to get around my problem is to erase cookies from my site and then recharge.

  Any ideas?

  site: http://condechi.com/test/movieTest.html

  Thank you

  O

  generally speaking, adding a query with changing value string will prevent items being retrieved in the browser cache.

• Problem with wireless built-in Elite e9260f desktop adapter

  I have an office of e9260f of elite who, after years of use with no problems, now has trouble establishing a connection without wire - the basic troubleshooting steps indicate that the adapter does not work and that it could breach having occurred.  Since it is integrated with the Board, is it possible to add a wireless card into one of the slots for use without conflict?

  Any other suggestions on a more advanced troubleshooting would be also useful.

  My wireless internet continues to work perfectly on my other systems and devices, is not the modem or the router.

  Hello

  Specificationsfor HP e9260f indicate a discreet wireless card.

  You should be able to order a replacement HP Partsurfer wirless card.  See the parts list for the e9260f. You can also google wireless adapter part number and might find available from other sources.