Problems with the raid PERC S100 controller

Similar Questions

• Problems with the RAID on ESXi 4

  Hello

  Although I have been using VMware Server for a few years, I am beginner with ESXi and would like some advice please.

  I'm putting a laboratory machine using the following environment:

  Dell PowerEdge SC1425

  3 GB RAM

  disks SCSI 2 x 73 GB attached to an Adaptec 39320 b. RAID controller with integrated HOSTRAID support.

  I worked on how to configure oem.tgz to recognize the RAID controller and have successfully upgraded to ESXi 4.1.0.

  Where I struggle is as follows:

  I wanted to install ESXi on two SCSI drives, configured as RAID1 mirror.

  I started by setting up a RAID1 with the Adaptec BIOS table. The problem is that when I installed ESXi, it would not fully start, claiming that I have two drives with the same UUID.

  So, I did it again, reset the controller (i.e. no RAID). This time, ESXi installed and running successfully, but as I suspected it would be started from a single disc and shows the other drive as a data store.

  Is there something I'm missing here? Should I persevere with RAID1 with the Adaptec BIOS configuration, or is there something in ESXi I should use?

  It does not appear on the HCL, and I expect that the card is also well supported and a RAID device. The fact that the card does not appear in the simple.map may indicate that it is an OEM version. Adaptec card BIOS can be flashed so I would check that. There are versions of pilot listed as entries of subtext of the HCL. See if there is any meaning with those.

• Problems with the network controller

  Hi, I have a problem with the driver for network controller. I mean my wireless does not work... it connects to the router, but it still has this yellow warning and will not connect to internet. I tried everything and it doesn't work. I have not found a pilot wireless on the hp site. I have a HP laptop model 15-r020sq.

  Hi, I used the driver that you post. Now I have the same problems as before. I went over the details of the driver it's what he know upstairs: PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C & REV_00

• problem with the SM Bus controller driver

  Dear Sir...

  My machine is Hp Pavilion 1150ee g6

  product no.: LX309EA #ABV

  I have windows 7 professional service pack 1

  I am from Egypt

  I'have a problem the appliance cannot read usb flash memory and after I cheked my device manager, I found a problem with the driver for Sm Bus controller (kindlly see attached picture)

  

  so I tried to download the driver from the site sp52791

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063 & LC = ar & CC = emea_middle_east & DLC = ar & sw_lang...

  But when I installed it I found a wrong message

  kindly I need your support to solve this problem

  Thank you very much for your cooperation

  Nader

  Hello:

  Try the driver directly from Intel...

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y & ProdId = 816 & DwnldID = 20775 & Keyword = Chipset + Installation + Utility & lang = eng

• Problem with the driver... Realtek PCIe Fe Family Controller

  I have a Toshiba Satellite L505D-S5983 and I have a problem with the driver for Realtek PCIe Fe Family Controller. What should I do? Thanks for your help.

  The program Driver Genius Professional are "junk" and must be avoided in most of the costs!   They will cause more problems than they find only the first available driver.  Most computer manufacturer can usually have 'rights' to customize pilots 'reference' for their offers of specific material.

  If your Toshiba has been sold with Windows 7 "pre-installed" then Toshiba is "obliged" to ensure the correct drivers.  You should check with the website of Toshiba and the hardware specifications of your model.  Then you should be able to download the necessary drivers directly from Toshiba.

• Hello! Someone has some problem with the haptic on Macbook 12 "2016 function? It does not work on my Mackbook.

  I'm trying to figure if someone has my problem with the haptic on Macbook 12 "2016 function. The option is checked in the preferences system, but it does not work.

  Thank you

  Hello luigi10m,

  Thanks for posting on the Community Support from Apple. From your post, it looks like your haptic feedback does not work when you click using your trackpad and the setting is enabled. I know that this is a great feature and it is important to make it work. I'll be happy to help you.

  First of all, I would like to assure you that in system preferences > Trackpad > clicking silencer is not checked, that might help. In addition, it would be useful to reset the settings of the SCM. You can find instructions here: reset the management system (SCM) controller on your Mac - Apple Support

  I'll also include those for you here:

  1. Stop the Mac.
  2. Plug the MagSafe or USB - C adapter to a power source and to your Mac.
  3. Use the built-in keyboard, press shift-control-Option on the left side of the keyboard, then press the power button at the same time.
  4. All the keys to unlock, then press the power button to turn on your Mac

  Take care!

• HP 255 g4: problem with USB and SM Bus controller

  I have a problem with the (USB) Universal Serial Bus controller and SM Bus controller.
  System identifies them.

  
  I installed all the drivers for my noutbook of this site, but it does not work...
  Please, help me!

  I believe that these devices are based on the AMD chipset driver package... USB 3.0 and SMBus Controller:

  http://support.AMD.com/en-us/download/chipset?OS=Windows%2010%20-%2064

  Top package. @Paul_Tikkanen will know for sure.

• Satellite U500-17F: problems with the new HARD drive

  Hi everyone, I got some troubleshooting with my Satellite and a new drive, I bought recently, because that is already damaged because of too many bad sectors. One is a Western Digital Scorpio Black 320 Bg (WD3200BEKT model number). It should be a fast reader but is not with my Satellite.

  After having mounted the drive in the laptop, I ran a new installation (with full disk format} Windows 7 (64 bit) with all the necessary drivers (that I downloaded directly from the Page of Support Toshiba.)

  The problem is that the laptop needs a lot of time to start and also to disable, and whenever I try to run an application or start a program (for example Firefox, or just a few windows applications), the laptop freezes for about 30 to 60 seconds, the drive no longer works (you can hear leaders put in position 'parking' and the HDD LED control is constant) ", no lights flashing).

  It seems that the drive (during this 30-60 seconds) in something as a stand-by mode. I ran a few Western Digital diagnostic tools and the car looks all right to 100%. It works also without any problems in the other laptop (HP Pavilion DV6500). Could this be a problem with the controller (Intel ICH9M - E ATA AHCI controller) driver?

  Any suggestion?
  Thanx

  Hello

  You use the latest version of the BIOS?
  Please check if you need a BIOS update. Of course I read in a few discussions on the similar question of Win XP you use Win 7 but its value to check the update of the BIOS and U500 series.

  In addition, I recommend check you the power of Windows 7 options.
  Disable in the power profile that you use power saving HDD.

  Just a question:
  You use the option AHCI in the BIOS?
  As far as I know it of possible to use either a compatible SATA AHCI mode.
  AHCI must be used because this option would use full SATA performance.

• I have problems with the mail (El Capitan)

  I have problems with the mail

  See writing an effective communities of Apple support question.

  Without knowing what are these problems there is no way we can really help you.

  Try this:

  Start the computer in Safe Mode, and then restart normally. It will be slower than a normal startup.

  MacIntel: Reset of the controller (SMC) system management

  Reset the PRAM and NVRAM on your Mac.

  Repair the hard drive and permissions - El Capitan

  HD recovery start:

  Restart the computer and after the buzzer, press on and hold down the COMMAND and R until the menu screen appears.

  Repair

  When the recovery menu appears, select disk utility and press the continue button. Disk utility charges and select Macintosh HD entry indented from the list on the left.  Click the first aid tab in the toolbar... If disk utility reports any errors that have been corrected, then re-run first aid until no errors are reported. Wait until the operation is complete, then quit disk utility and return to the main menu. Select restart from the Apple menu.

  Now, download and reinstall OS X El Capitan 10.11.3 Combo Update.

• Problems with the installation of recovery - Satellite A300D - BSOD

  Hello

  The laptop in question (TOSHIBA Satellite A300D) recently stopped starting (BSoD).

  So, I tried using the recovery disk, but there is no help. What happens is:
  -After about 10 minutes of waiting, the first language menu load, so I click on "next".
  - Then I again click Next and accept the message that my HARD drive will be erased
  - Then I see a cmd prompt that says "try to remove all the letters of partitions possible...". »
  -There is also a minimized command prompt that says something like "RAID failed to initialize."
  -And then nothing happens.

  Is this a hardware problem? I also tried a full installation (instead of recovery), which, even once, is simply not. None of the errors is - it just freezes.

  Any help appreciated.
  Thank you.

  It is not easy to tell what can be the problem, but if you were not able to install the OS by using two different facilities CDs/DVDs, so there must be a problem with the HARD drive.

  The warranty is still valid?
  I mean you can contact the nearest Toshiba authorized service provider and explain the situation. They can swap the HDD and again test the recovery procedure.
  Can you get somewhere 2,5 SATA HDD for testing?

• Satellite L750D-1FD - problems with the display driver

  I got this laptop from my uncle and it was filled with junk and crapwares so I did a clean reinstall and upgrade Windows 7 Home to ultimate. I have a problem with the GPU, windows does not recognize it, or doesn't fly chart AMD.
  Processor is AMD A8 - 3520 M APU, and I think that the GPU is a Radeon HD 6620 G or something before the re-installation. I can't change the resolution, it stuck at 800 x 600, memory shows by n/a, Direct X features are not available, not from the downloaded display driver Toshiba worked.
  Dxdiag appears to the:

  Name: Standard VGA Graphics adapt
  Manufacturer: Advance Micro Devices, Inc.
  Chiptype: AMD ATOMBIOS
  : Type DAC: 8 bit
  Memory Approx.Total: n/a
  Current display mode: 800 x 600 (1 Hz)

  It nothing and can do with this laptop now because the GPU does not work as expected. Please, help me to solve this problem.

  Hello

  I found only Satellite L750D-1FD so I think you have this model. I want to help you on any other way. Here is the correct order of installation for Win7. Please check and install all the available stuff you can find on the download page of Toshiba - http://www.toshiba.eu/innovation/download_drivers_bios.jsp

  Win7 SP1
  4.9.2.0 TOSHIBA supervisor password utility
  TOSHIBA HW Setup Utility 4.9.2.0
  TOSHIBA Assist 4.02.02
  TOSHIBA ReelTime 1.7.18
  AMD driver 1.0.0.52 xHC
  8.834.1 - 110420 a-118118C-Toshiba AMD display driver
  TOSHIBA value added package 1.5.10.64
  ATI HDMI Audio Driver 7.11.0.7710
  Conexant Audio Driver 8.51.1.0a
  Wireless LAN driver
  Synaptics Touch Pad Driver 15.2.11.1
  V4.07 Bluetooth Monitor
  Atheros Bluetooth Driver Package v1.0.7 Filter
  Battery Bluetooth for Windows by Toshiba v8.00.06 (T)
  Atheros LAN Driver 1.0.1.50
  Card reader Realtek 1.0.0.14
  TOSHIBA 1.0.4 Wireless LAN indicator
  TOSHIBA Sleep 1.4.2.8 utility
  3.1.8 TOSHIBA face recognition
  TOSHIBA eco Utility 1.3.2.64
  TOSHIBA HDD/SSD Alert 3.1.64.8
  TOSHIBA PC Health Monitor 1.7.7.64
  ConfigFree 8.0.38
  TOSHIBA Web Camera Application V2.0.0.21
  TOSHIBA V4.00.7.01 VCR - HAS
  TOSHIBA resolution + plug-in for Windows Media Player 1.1.0
  TOSHIBA Disc Creator 2.1.0.9 for x 64
  TOSHIBA Network Device ID registry setting tool 3.0.32.4 - 16_wMSI
  TOSHIBA Media Controller 1.0.86.2
  TOSHIBA Media Controller plugin 1.0.6.1

  If you need assistance more let us know.

• Problems with the resource of labview execution 2 visa

  I use two loops in a labview code all-in - connects to a motor controller and other is used to connect to a multimeter agilent. As soon as I run this VI, the loop to connect to the controller stop working and only used to configure agilent machine works. If I remove the second loop (connecting to the computer of agilent), the code works fine. I guess it's a problem with the execution priority. Could you please review the attached code and let me know any problems with it.

  COM1 and Com3 share an interruption.

  Go to the BIOS of the computer and set the port to Com3 to the Com2 port, then they will be on their own interrupt and see if that helps.

  FYI

  COM1 and Com3 share IRQ3

  COM2 and Com4 share IRQ4

• Windows Media Player cannot play the file because there is a problem with the audio device.

  Original title: Media Player

  I tried to play my music in media player and they will not play. The tab that appears says "Windows Media Player cannot play the file because there is a problem with the audio device. It might not be a sound device installed on your computer, it can be used by another program, or it may not work properly. Also, I can not play music in the window, that I downloaded everything. If anyone has an answer I would appreciate the help. Thank you

  Hi MikeMcKayXE,

  ·         What is the brand and model of the computer?

  Follow the suggestions below for a possible solution:

  Method 1: Quit other programs that may be using your sound device, and then try to play the file again.

  Method 2: Install an updated driver.

  Step 1: Firstly uninstall the audio from the device manager driver and Add / Remove Programs

  a. click Startand then click Control Panel.

  b. click Systemand click on the hardware tab, then click Device Manager.

  c. to the title sound, video and games controller, check the sound card that is listed.

  d. right click on the sound card, and then click Uninstall driver.

  Step 2: To see if an updated driver is available, use Windows Update or access the sound device manufacturer's Web site.

  Follow these steps to do the same thing:

  a. click Startand then click Control Panel.

  b. click Systemand click on the hardware tab, then click Device Manager.

  c. the title sound, the video controller and games, make sure that the sound card is listed.

  d. right click on the sound card and then click Update driver to install the latest version of the driver.

  e. visit the sound card manufacturer's Web site to determine if a newer version of the driver is available for download.

  Method 3: If you have multiple audio devices installed on your computer, try to use another. The selected audio device might not support Secure Audio Path (SAP).

  You can see the following article for more information:

  Resolution of the problems of reading in the Windows Media Player for Windows XP

  http://support.Microsoft.com/kb/306317

  Let us know if that helps.

• Problem with laptop Lenovo T400 video controller

  Hello

  I have problems with the video controller on my laptop of Lenovo T400.

  Brand new and installed with Windows XP factory.

  He maintains and prompt to install the drivers for the video controller.

  I tried to use the CD and downloaded the chipset and video drivers Lenovo Web site, but the problem persists.

  Anyone encountered before?

  Thank you and best regards

  Solo

  option 3.

  Discreet GPU = ATI GPU
  Integrated GPU = Intel GPU
  Switchable graphics = Intel or ATI switchable by Vista and Win 7 OS Thinkvantage Power Manager.

• Problem with the screen size of my application in the emulator for BlackBerry 10

  Hello, I have a problem with the emulator for BlackBerry 10 and is as follows:

  When I run my application in the emulator waving, sounds good and all content is complete, however, when I run the application in the emulator for BlackBerry 10 soft looks as if she had a zoom very large level of predefined way and only see a part of the application.

  With controller emulator, I have changed the level of 70% zoom, but still does not work.

  Here, I'm posting two photos:

  

  

  One future half-assed answer

  var dpr = 1; // To set the meta on a real device to get 1:1 pixels
  
  if(typeof window.devicePixelRatio != 'undefined') // Does device support devicePixelRatio?
      {
      dpr = window.devicePixelRatio;
      }
  
  if(dpr) // Set up the right meta
      {
      var meta = document.createElement("meta");    meta.setAttribute('name','viewport');
  
      meta.setAttribute('content','initial-scale='+ (1/window.devicePixelRatio) + ',user-scalable=no');
      document.getElementsByTagName('head')[0].appendChild(meta); // Inject meta
      }
  

  This works perfectly, but must be placed in thethe document FIRST and foremost

  Live JS is used to avoid problems of library management

  It won't work in Wellington but works perfectly on all devices I've tried

  As mentioned in the code above just packaging needs in the script tags and setting very high index.html HTML code as you can get - right after