Put Hibernate & standby does not work on Portege 2000

Similar Questions

• 1670 CDS satellite - modem does not work on Windows 2000

  Hi-

  I removed the Toshiba W98SE and installed Win 2000 (new installation). I managed to put it on the audio driver using downloads on your website (and it works).

  I do a test on the dial installation upward and that you have installed the modem also since your website (Conexant Soft K56 Data, Fax PCI Modem). This is intended for W98SE but microsoft message is

  The port looks ok. Please advise - is it the right driver?

  Thank you.

  A Windows 98 driver does not work on Windows 2000. Therefore, you need a new driver for Windows 2000.

  I have checked the Toshiba site but your model no available Windows 2000 driver exists.
  I think you have to search the site of the factory of the modem. Maybe you can find a driver or another portable model that has the same modem.

  Good luck!

• Toshiba Digitizer Pen does not work on Portege Z10T-A

  I have a Portege Z10T.-a.

  I bought new Toshiba Digitizer Pen PA5133U-1EUC.

  The link below, this pen is compatiable on my laptop. But it does not work. Y at - it no adjustment or the driver of this pen?

  http://www.Toshiba.com/us/accessorie...s/PA5133U-1EUC

  I think you should check if the device supports the digitizer and if so, you will need to calibrate the pen and touch settings.

  For this I recommend that you review the Microsoft FAQ on pen and touch settings:
  http://Windows.Microsoft.com/en-pH/w...Sked-questions

• Touchpad does not work on Portege R100

  Hello

  I have recently boght a Toshiba Portege R100 without any installation CD Windows XP Home Edition worked fine but the touchpad is not.

  I installed additional drivers of Toshiba. Now, I'm able to adapt to all kinds of things about the Touchpad, but still it does not work. I was also running Knoppix 5.2 since July 2007. Same problem with Linux.

  Have I not a faulty laptop? How will I know, please?

  Have you tested the touchpad with Windows XP?
  You connected an external USB mouse and you have the same problem?

  Normally the touchpad should work without a driver, they are part of the operating system.
  You can disable/enable it with FN + F9.
  I'm not sure, but you can also enable/disable the touchpad in the BIOS.

  It could be that the touchpad is defective, but ask an ASP for help. They can check the necessary parts for laptop and Exchange.

• Satellite L40 - Sleed and standby does not work correctly

  I have a portable Satellite L40 and it worked correctly until now. I turn and after I have put on standby (stand-by) mode; When I want to use my system, so to get that back to normal (I press the turn power button to exit the mode "standby" button), Windows Vista 32-bit restarts - it is not back to the moment I left it before the "sleep mode".

  Therefore, restarting Windows Vista 32-bit, and the screen "Windows has been disabled incorrect" appears instead to return to the configuration of the system that let him before sleep / standby mode.

  What can I do to fix this and make "sleep" mode works correctly?

  Hello!

  In your case, I'd do a BIOS update. You can search for updates on the Toshiba site
  http://EU.computers.Toshiba-Europe.com

  You should also look into the mangment of power. Here, you configure what happened when you close the screen, press the power button and so far.
  I found a great thread on this topic:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=141529𢣙

  Good bye

• Network does not work after Windows 2000 SP4 P2V

  It has been a roller coaster get this virtualized machine.

  A little history: this machine is Windows 2000 SP 4 with update Rollup 1. After you install the Update Rollup 1, virtualization tried it and it gets to 97% and then I get the message error "vmware agent has encountered an error. When I try to start the machine, I get a BSOD with error inaccessible_boot_device.

  After reading some discussions fo I found a solution of reconfiguing the virtual machine then it will start. So now, I have a virtual machine that will start.

  Now my problem is that networks do not work. I removed the network card, has added a new, tried static and dhcp, through the Add/Remove programs and uninstalled all the devices HP and Compaq, went into Device Manager and deleted all drivers HP and Compaq or component, rebooted countless times and I am still ending up with no network connectivity.

  The network card on the computer virtual says it is connected and he says is to receive, but not send. It is not pulling a DHCP address and a static address gets no where also.

  I have more than 50 virtual machines so I know this isn't a problem with my network, it must be on the virtual machine itself. I don't know what else to try, and I'm open to suggestions.

  Thank you!

  Have you tried to repair the winsock?

  1. Go in Start > run, type: netsh int ip reset c:\resetlog.txt

  2. Restart your computer and you're done.

  3. Follow the steps below if you have XP SP2 (this only works on windows XP SP2 and later versions).

  4. Go to regedit.

  5. Go to HKEY_LOCAL_MACHINE/System/CurrentControlSet/Services

  6. Click on Winsock and Delete.

  7. Click on Winsock2 and Delete.

  8. Close registry.

  9. Restart your computer

  10. Access the properties of the LAN connection

  11. Click the install button in the Properties window

  12. Select PROTOCOL, and then click the Add button.

  13. Click the disk...

  14. Type C:\windows\inf\nettcpip.inf in the dialog box, and click OK.

  15. Choose from the list of INTERNET TCP/IP PROTOCOL in the list, and then click OK.

  16. Click CLOSE.

  17. Restart your computer. (At this point the Winsock is complete)
      not only avoid this problem from happening in the future, but also
      to make the process much easier you update Windows.)

  Try the following steps: http://support.microsoft.com/kb/837333

• Satellite C75 - A - auto sleep (standby) does not work

  Hello

  My Toshiba SATELLITE C75 - A will not automatically in standby mode (standby) after some time of inactivity.
  Eve works well when I trigger it manually with the start menu and when I do not use the mouse or keyboard for a while, the screen turns off. But neither sleep nor put into hibernation is turned on after the interval set in the energy saving plan.

  When I run
  powercfg with fluo compact
  on the console I get

  "PCI Express Active State Power Management (ASPM) has been disabled due to incompatibility with the hardware on this computer."

  My BIOS is updated.
  I would be really grateful for any advice.

  Hello

  Have you tried to activate the Hibernate mode and standby manually by using the powercfg command?

  Here is a list of possible options regarding the powercfg command:
  [Powercfg command-line options | http://technet.microsoft.com/en-gb/library/cc748940]

  For example with the command * powercfg-h on * turns the hibernation feature on or off.
  You can use also returns a list of devices that support hibernation or sleep

  By the way: what system are you using?

  In addition, you can try to activate or disable the PCIe Link State Power Management in Windows

  Go to control panel-> Power Options-> advanced power plan settings
  Here, scroll down and expand PCI Express and Link State Power Management.

  Currently setting (without battery) or on battery and sector, open the drop-down menu, select Off or ON and click OK.
  If you select No, there is no energy savings, and current runs regardless of which state that the laptop is in. (depending on whether your laptop is plugged or not).
  On battery: Off = PCI Express even will communicate using the power of the battery.
  Plugged in: Off = PCI Express communicates when it is connected as well.

• Re: Button on the upper right does not work on Portege R500

  Hello

  At the top right of my keyboard (Portege R500) theres a button that shows a place in the foreground with a Sun in the background.

  I guess it is a kind of glare/brightness button to be used outdoors.
  However pressing this does nothing.

  Can anyone suggest what's this button and how do I make it work?

  See you soon,.
  H

  I think you're talking about the outdoor switch.

  This backlight button on / off turns on and off the display backlight s.

  Are you sure that you do not notice any difference this button?

  If you turn off the back light outside in good weather, you can use the computer for an extended period.

  Maybe I m wrong, but usually he should be able to configure this button in the power OS Options.

  Greetigns

• Hibernate mode does not work on my Satellite L650-1PE

  Hi all

  I have Toshiba laptop Satellite L650-1PE system (psk1je) & windows 7 32 bit & I updated the BIOS to version 2.40... so I can not put windows 'Hibernate' mode... the screen turn off then it turns on again!

  Y at - it an update or what I can do?

  Help please.

  Thank you

  .

  Hello

  Maybe you should enable hibernation, first:
  Do this:
  -Start CMD (control box) in search, type CMD and press ENTER
  -Type powercfg /Hibernate + it +.
  -Close the box and go to Advanced Power Options
  -In advanced options to sleep, expand the sleep tree and disable standby hybrid.
  -Now go back to the start menu and you will see the new entry into hibernation.

• FN + F5 to change device display does not work on Portege R600

  Portege R600-11 b Win 7 ultimate
  I wanted to show my photos on the TV using the vga output. Connected everyting, pressed FN + F5 and watch LCD dialog box. Support again, still lcd. tried the keys of direction, no joy, still lcd.

  plugged my trusty R100 instead of the R600 and bingo, works very well

  I'm sure this used to work on the R600 90%. (Actually, what I remember is that it just worked first time with no keyboard at all operations).

  Someone suggest anything happy?

  Steve

  It seems that your TV is not recognized correctly.
  Did you use FN + F5 option in the past?
  Are you using the original pre-installed OS that you got with your laptop Portege?

• Standby does not work on satellite

  Hello
  I think I have the same problem that TSC, the function of sleep is not enabled on my laptop. When I click, start, stop - the standby key is "grey", IE. I can't click on it, I can only click on stop or restart.
  In the toshiba power saver options, the wait cursor is also "grey" in each profile, so I can't activate it.

  «In normal power saving options, clicking on the Advanced tab is not raise an option ' ' activate Standby ".» All that there is the options of what to get I hit the power button or close the lid. On closing the cover option (which is used to put my laptop on standby) it only has now an option, "do nothing". It is not yet all that exists.

  Please please can someone help?
  My laptop is overheating and the fan made such a noise if I just leave it on, and I'm tired of having to launch and shut down five times a day.

  Thanks in advance!
  Jenna

  Hello Jenna

  I assume that your laptop is not preinstalled with recovery media just with your own installation of the OS. Am I wrong?

  As far as I know after sleep button graphics driver installation must be enabled. Hibernation (support) option must be enabled manually, but waiting has to be there.

  I put t know which satellite you have, but of course, the device must be cleaned properly. Remove the unit from the dust will be able to take a breath and cooling fan will not run constantly.

• Standby does not work as specified in the menu Power Options

  XP Home Edition, IBM computer.  Ignores specified times in Options power to go in standby mode.  I can choose the eve of the closing screen.   Which have been occurring for several weeks.  No new software or hardware added.   Installed MicroSoft Security Essentials and run frequently, soapparently not a malware issue.

  Sometimes the system will not remain in standby mode when put closure... screen reboot seems to fix this; don't know if it is related to the question above.

  "willm1961" wrote in message News: db8b406e-ef18-418 c-bc17-29b4b7a9e4f1...

  XP Home Edition, IBM computer.  Ignores specified times in Options power to go in standby mode.  I can choose the eve of the closing screen.   Which have been occurring for several weeks.  No new software or hardware added.   Installed MicroSoft Security Essentials and run frequently, soapparently not a malware issue.

  Sometimes the system will not remain in standby mode when put closure... screen reboot seems to fix this; don't know if it is related to the question above.

  Check background processes - which can prevent the machine from sleep mode.
  Check the scheduled tasks - that can bring the computer from sleep mode
  Make sure that the cat is not walking on the keyboard to put the machine out of sleep. = check the BIOS settings to make sure that other devices are not out the machine in standby (modem/NIC/mouse, etc)
   
  
  --

  Noel Paton | Nil Carborundum Illegitemi | CrashFixPC | The lazy three fingers

• My Inbox keeps asking for a password, but when I put in it does not work. How to fix?

  "(kay, je ne sais pas quel est le problème, mais j'ai quelques théories: 1) I sent a set of images slap to my"[email protected]"email account (I use e-mail to contact you because I can't go on my main email)." The account that I signed up with is '[email protected] '. Both accounts have exactly the same parameters, but the works of tvqueen13 and monarch is not. Maybe I stuffed up the e-mail account of the monarch? If so, how can I solve this problem? (2) I also have good Emsisoft Anti-Malware and AVG security 2014 (purchased, not free), but somehow got a rash of infections of Trojans (IE. TrojanHorseInject2.BJPG & BJPP, TrojanHorseMSIL6.UOM, MSIL4. ALBK). I have worked with Emsisoft to clean my computer, but no matter what tools I use, AVG always says that I have an infection (or more) in my temporary files. I had to uninstall AVG to run something and not him have not yet reinstalled. Emsisoft said I'm all good, but I do not. I get adware diverting my sites too. I'm at the point where I think I'll have to swap on my C drive. Then... you can help me get my email [email protected] to work again? Thank you, Kelsey monarch

  Oh and connect to the Webmail to shaw and move one of those large emails talked you in the beginning on a different folder on the server. Moving them to the Inbox will be unlock download new messages, if this is the cause.

• When I opened Installer creative cloud asked that the password when I correctly put in it does not work

  Try to get a trial in creative and Photoshop clouds, but when I open the installer of creative cloud he asks username and password. When I put my adobe user and the password which is OK he just shakes and goes no further

  Hello

  When you launch Installer creative cloud he needs your Mac password for authorization of user account to install the software. I hope that you do not use your Adobe ID password on this line.

• 3G does not work in Portege Z830

  Hi all:

  Option dial-up for my Sims made its appearance is no longer in the network and sharing Center (he appeared in the past), and as a result I can no longer use the 3G function. Is a special driver or setting necessary to (re) activate?

  The specs of my computer are:

  Model: TOSHIBA PORTEGE Z830-11J
  REF.: PT225E-00T00EEP

  Thank you in advance for your attention,
  JM

  Have you tried reinstalling the driver 3G?
  You can find it on the download page of Toshiba.