Similar Questions

• Incompatibility of pilot PXI 5105 and unable to be detected by OR-SCOPE FPS with NO-SCOPE installed 14.1

  I am setting up test bench and just add a PXI-5105 card to my chassis SMU-1078.

  I currently have NO-SCOPE 14.1 installed on my PC host and target RT.

  When I try to run the Test panels in MAX, I get the following error:

  

  If I try to launch SFP-OR-Scope, it does not detect the card of the scope:

  

  The map seems to indicate as normal in my remote systems in MAX.

  For the host, the Installation of NOR-SCOPE includes:

  • Configuration support 14.1
  • 14.1 development support
  • 14.1.1 duration

  For the target RT, Installation of range OR watch as 14.1.0.

  I even checked in the feature add/software for the remote system see if a driver incompatibility was actually present:

  

  I have also confirmed in the Readme that PXI-5105 is supported OR-SCOPE 14.1.

  I'm kind of dead in the water on other ideas to investigate on concerning the system is behaving properly with the new card.  Other ways suggested for study?

  I continued to play with setting up more and find my VI has been targeted my Windows host instead of the goal of the RT.  I'm nowable to see my map of scope 5105 now through Labview + RTM.  Thank you for tolerating a newbie.

• Digitizer PXI-5105

  Hello

  I send the same question last Friday.

  The scanner we use is an error occurred.

  We use the wondows computer 8, running the program Max.

  The error code is 200313 self-test occurred.

  Hi derives1,

  Here are some steps you can take for troubleshooting:

  -Try the card 5105 in another location in your chassis or even in a different chassis, to ensure that it is not a problem of chassis.

  -Make sure the version of NI SCOPE you are using is compatible.  You can update to the latest version, make sure just that you check the compatibility. http://search.NI.com/nisearch/app/main/p/bot/no/AP/tech/lang/en/PG/1/SN/ssnav:NDR/q/NI%20scope/

  -Force Windows to re - detect the device and driver. To do this in the Windows Device Manager to remove the device, and then click Action > search for new devices re - detect the hardware.

  Error-200313 from the PXI-5105 often results in an RMA number (Return Merchandise Authorization) to repair the unit. Try the above steps, and if the card still gives you the same error then create a service request, then you can work more closely with an Applications Engineer to start the RMA process.

  In addition, I can't find the post you mentioned last Friday, but we ask as a policy forums OR you post once on a problem. This will keep things like organizaed as possible!

• error "device could not be calibrated" to PXI-5105

  Hello

  I want to calibrate my PXI-5105. But I get an error in MAX and a calibration vi. I tried to install NO-SCOPE 4.1.3 on PXI, but that does not solve the problem. I have labview time real 13.0.1 installed. I enclose the error messages.

  See you soon,.

  Syed

  Syed,

  So there is not a lot of good information on this error.  Automatic calibration works by connecting a known signal that is embedded in the digitizer at the ADC and to adapt the constants and phase shift.  The 234107 error means that there is a problem with this calibration signal or the signal to the ADC path, etc.  This known signal is calibrated during the external calibration and since your device is off external calibration (calibration necessary since February 2011), the problem is probably the calibration signal drifted too far from its known value.

  To resolve this problem, you will need to send the jury in external calibration, and I would recommend National instruments, send it because if there is a problem with the hardware with the Commission, we might be able to solve this problem, as well as of him have calibrated.

  I hope this helps.

  -Nathan

• Extract and save all the channels of the PXI-5105 with 4 M of edge detection... Help!

  Dear collegaues!

  Please help me to improve my request, exhibit attached and sorry for my English.

  So my task is to extract and save all the channels (eight) of the PXI-5105 with 4 M of detection of peaks and sample rate 4 M with loop 1 sec...

  Entered all my channels are wiring detectors NaI with 0, 5... 1 microsec pulse (really) width and 0 kHz at not more than 40 kHz freq.

  Why I chose the registration of 4 M and the sampling frequency of 4 M namely? Answer is that I tested previously PXI-5105 40 kHz generator and pulse width 0.5 microsec. It works great and detection of peaks indicate 40000 pulses/s for me. If I set lower than 4M record and sample rate of 4 M, it is without work. In my honest opinion record 4 M and the frequency of sampling of 4 M are parameters very min.

  In the detection of peaks time present only 6 working channels... When I connected to diagram more 6 "detector.vi peak" - I see the error "...". out of memory... ».

  Advise me please, what needs to be done to it, it's all working well.

  
  

• Unable to trigger pxi-5105 exported signal pxi-4461

  Hello

  I use a chassis PXI-1033 with a PXI-4461 (daq) in slot 2 and 4-PXI-5105 in slots 3-6.  I want to use the 4461 to export a reference trigger signal to of the 5105, but when I try to run my program I get the following error:

  Error-89126 occurred at DAQmx Read (Analog DBL 1Chan 1Samp) .vi:1

  Possible reasons:

  Trigger line asked could not be booked because it is already in use.

  Property: RefTrig.OutputTerm
  Property: RefTrig.Pulse.Polarity
  Target unit: PXI1Slot2

  Task name: _unnamedTask<89>

  The Subvi I use to export the signal is built off an example I found.  At the moment it is only under the scope of my code mode (I'll take care of the datalog part later).  I'm not sure what I'm doing wrong, any help is greatly appreciated.

  Thank you

  John

  Hi John,.

  T Clk select a PXI_Trig lines used to deliver pulses of synchronization between devices.  Since that you configure T - Clk before configuring the signal to destination, the driver doesn't know that you plan to use PXI_Trig0 to export the reference trigger.  I guess that's to select PXI_Trig0 as the line to book the pulse of synchronization.

  I recommend that you try to export the signal to one of the other lines PXI_Trig - this should I hope to correct the problem but keep inform us if it is not.  Thanks for posting and have a great weekend!

  -John

• Problem of delay time PXI-5105

  Hello

  I'm running the PXI-5105 (@ 60Msa/s/ch 12 bit 8Ch) using the attached VI. I put it to trigger off channel 0 to 1V.  When I put in a sinusoidal waveform of cycle 5, it seems that the scope triggers too late and I only see 4 of 5 cycles.  I confirmed this by generating a sinisoid of increasing amplitude across a PXI-5412 and again once the waveform has been truncated, as if there is a delay after that relaxation hit.  (btw, I have an oscilloscope running in parallel and the waveforms appear perfectly here)

  Why this is happening any help would be really appreciated.

  Thank you!

  Actually - problem solved.

  When I played with him I had inadvertently set it to DC coupling.  Coupling AC fixed.

• How can I display an analog input for the PXI-5105 on LabVIEW?

  Hi all

  I am very very new to LabVIEW and I started to tinker with it. I use the version of LabVIEW 2010 SP1 on Windows 7 OS. I also have the chassis NI SMU-1073 with SMU-6361 and PXI-5105 modules and the chassis is connected to my PC via PCI. I became familiar with the devices and trying to see some analog signals to one of the channels on the PXI-5105 module in a graph in LabVIEW.

  I would appreciate your help.

  Hello Henokview!

  I would like to read through these tutorials to understand the steps of programming of the NOR-SCOPE, NOR-DAQmx. After reading these links below, you will be able to understand how to connect the output of a readfunction to a chart or table.

  DAQmx

  http://www.NI.com/white-paper/5434/en

  OR-SCOPE

  http://www.NI.com/white-paper/3382/en

  Best regards

  Jonas

• PXI-5105 resolution not quite as expected.

  I have a system with the guidance of PXI5105, and I use it to sample a signal on beach of 30V (+/-15V), 1megaohm input impedance, 1megasamples by the second sampling rate.

  The PXI5105 has a resolution of 12 bits, so I expect to see the steps in the quantification of 30V / (2 ^ 12) = 7.32mV

  Acquisition of a stationary signal, the noise extends over 7 discrete levels, so spans 6 quantization steps (see file attached .jpg)

  Ranges of noise on 52mV (it goes from-16 to + 36mV), so measured quantification step is 52 / 6 = 8.66mV

  I'm missing something obvious here. Why the difference between calculated and measured resolution?

  My only thought is that resolution is not linear in voltage range. I expect there are a few non-linearity, but didn't expect so much.

  Fill the void in my knowledge!

  Hi Bandit,

  The gap you see is due to the fact that the input range effective from Ridge to ridge of the Board of Directors is not exactly 30V.  The overall increase in analog front end that lies between your input signal and the ADC has initial inaccuracies and can also drift over time and temperature.  These effects can be minimized but never completely eliminated.  As a result, we design boards to have a peak-to-peak input nominal range is slightly larger than the ideal ranges specified in the data sheet.  This ensures that the jury will never less that ideal beach, even though the gain of slightly derivatives (this way you can always be assured that if you use the 30Vpp range and put you in a 30Vpp signal you will never saturate CDA which results in a loss of the signal information).  The 5105 has an internal calibration of precision voltage generator which is then used to calibrate data at the scale that you are returned.  This results in a slight reduction in resolution (increase of the voltage/ADC code) as you have seen, but the tension you be returned is always exact specification of precision AC / DC published in the data sheet.  If you know that the resolution calibrated, it is possible to get this information from the output of cluster "wfm info" from the "Fetch (poly) .vi niScope" when you use the vi in a mode of extraction of binary data.  Sorry for the confusion and hope this helps.

  Kind regards

  -Matt

• PXI-4461 generate voltage update

  Hello

  When you try to run the sample Daqmx VI "Gen - Update.vi of tension" with an NI PXI-4461, I get the following error:

  200758 error:

  "Type of sample Timing is set to on demand that is not supported for analog output on this unit"

  What does that mean?

  Is there another way to generate a constant DC signal with the 4461?

  Also - for next time that consider us to buy a new card - where can I get information on DAQmx properties (like this one) are supported for each camera?

  Thank you

  Ran

  Hi Ran,

  The 4461 NOR supports HAVE no single-point / AO of because it is based on delta-sigma converters a/n/CED, which require a clock free run at a constant speed.

  There are two ways to output a signal DC with an NI 4461 (or NI 4431):

  1. Continuously to generate a waveform to DC (containing several repeated values).
  2. Set channels DAQmx > AO. IdleOutputBehavior to "Maintain the existing value" can generate several updates.

  The help of LabVIEW has a page of "properties of the NI PXI-4461 supported", but it does list all the supported values for each property for each device. NOR-DAQmx help has a page entitled "Considerations for DSA timing devices" that talks on this subject:

  "

  Considerations of timetable for DSA devices

  Supported sampling frequencies

  Unlike some other devices DAQmx, DSA devices have a maximum and a minimum sampling frequency. Check your device specifications determine the range of sampling frequency.

  Other considerations of DSA calendar

  DSA devices do not support the type of synchronization on demand. All acquisitions of DSA and generations require hardware timing of a stable clock.

  DSA devices do not support external synchronization sources of arbitrary external signals such as tachometers and encoders. PFI lines on the DSA hardware can accept external clocks. You can program a DSA device to use an external clock only when it is a slave in several synchronized system device. Refer to synchronization of the DSA for more details.

  "

  Brad

• PXI offset 5105

  Hello

  I'm using a PXI-5105 with LV SignalExpress.

  I want to measure the tension of the card system with power supply of 5V.

  I want to set the offset, but when I put a value, I got the error:

  «Requested invalid baseline shift.»

  Is the range of voltage: 5V

  Offset is: 4V

  The impedance is: 1Mohms

  What's wrong?

  Best regards

  Nicolas

  Hi Nicolas,.

  Unfortunately, the 5105 NOR support the shifts of power. For a quick overview of the features supported, seefeatures supported by the device of scanners using high speed. Best regards

• PXI noise 5105

  Hello

  I want to use PXI-5105 on SMU 1071 chassis for strain measurment by conneting the strain gauge by the to 5105 wheatstone bridge circuit using BNC cables. I'm using Labview for the same thing.

  (i) I get the variable noise (0,008 to 0.010 V) with no connection to the input channel.

  (ii) I'm unable to balance / minimise the noise to zero by subtracting signal from one channel to another (differential input).

  Data acquisition parameters:

  Input voltage: 5V by DC power supply

  All cables used are sheathed in copper cables

  Sampling rate: 5ms / s

  Number of samples to read: 2000

  We worked on the reduction of noise for a long time. Any help will be much appreciated.

  Thank you

  Vinod

  Hi Vinod,

  Keep in mind the accuracy of the unit 5105 is specified to +/-2mV.

  

  Also, you can check that your device has been calibrated on the outside and in his external calibration cycle.

  When I watched a 5105 digital signal in a similar setup to yours, I saw the same kind of (about) + / 2mV noise.  I don't think this is unexpected.  Especially if you let the front end of your digitizer not completed, it could recover the additional ambient noise.

  Why you choose to use this scanner for a measurement of the strain gauge?  There are several other products OR Lane County and specifically designed for measures of constraint.  Here are a few resources:

  Strain with gauges

  http://zone.NI.com/DevZone/CDA/tut/p/ID/3642

  SMU-43xx Bridge Module Product Pages

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/208288

  Dynamic signal acquisition board

  http://forums.NI.com/T5/dynamic-signal-acquisition/BD-p/100

  -Andrew

• PXI SFP 5105 configured Vs Acquisition VI

  Hello

  I recently started to use the NI PXI-5105 cards, I need to capture (noise level<20KHz) on="" top="" of="" my="" dc="" signal,="" i="" used="" software="" front="" panel="" to="" capture rising="" edge="" of="" an="" analog="" signal i="" was="" able="" to="" capture="" signal="" when="" it="" meets="" my="" trigger="" requirements="" same="" as="" configured="" acguisition="" example="" vi="" also="" vi="" recommended="" input="" signal freq=""  ="" is="" 100khz,="" what="" changes="" i="" need="" to="" do="" in="" order="" to="" make="" this="" vi="" to="" trigger="" when="" the="" noise="" level="" on="" my="" dc="" signal="" exceeds="" certain="" point="" can="" anyone="" please="" help="" me="" with="" this="">

  Thanks in advance!

  Hey djo.

  If I understand your description, the best sounds of relaxation as it can be a trigger of hysteresis with coupling AC trigger in order to eliminate the effects of your DC signal. You will then be able to adjust the amplitude of the noise that you are looking for as the level to which you want to trigger off. You can find information about the options available with the help of scanners trigger high speed OR under Fundamentals > trigger.

• Background basket 1409 PXI trigger

  Hello

  I have an installed 1033-1409 PXI, PXI-5105 pxi chassis. I want to route a signal to trigger for PXI-1409 to the RTSI bus backplane and then use this signal to trigger RTSI bus trigger PXI 5105 as a trigger to start. PFI 5105 PXI is already occupied by the synchronization code signal Therefore, the only way to configure the startup to 5105 trigger signal. I'm using C++. However, after reading the reference of function and the examples coming with 1409, he does not seem such a function to perform this task of routing. Is it possible to 1409 and 1033 for this? If possible, could someone give me a short example? Any suggestion is appreciated.

  Sincerely,

  Bin

  Hi Binar,

  You will be able to drive a trigger on the lines of the RTSI with your PXI-1409. If you look at this knowledge base article, you will see that the projector 1409 is one of 5 Councils who have RTSI triggering capabilities. That being said, if you look in the NIIMAQFunctionReference document, you will be able to find information about the necessary trigger under NOR-IMAQ functions functions > functions high-level > functions of i/o signals. In particular, you will need to look at the imgSessionTriggerDrive2 and imgSessionTriggerRoute2 functions.

  Paul M

• SINAD SNR NI 6733 sine wave

  Hello world

  This question is perhaps a bit too much, because I have seen already too many messages on SNR and SINAD in this forum. But honestly, I've been looking for all threads and I couldn't find what I really need, that's why I am posting this however.

  My question is, how do I get the real analog sine wave SINAD or SNR output PXI-6733. I tried to look at example SINAD base measureand also niScope EX Fetch to always use the PXI-5105, but I don't think I get the real value of SINAD just by simply using the block measure SINAD. I get only 38dB SINAD using the sampling frequency of 1 MHz and 100 k points, by extraction. IM geneating 10 kHz sine wave with PXI-6733 for example Cont Gen Wm-Int Clk.vi voltage.

  Any idea what I miss here?

  Hi Mystogan,

  If I understand you correct, generate you a sine with the PXI-6733 and measure this return signal

  with the PXI-5105 and the expected value are reached because you only get measures

  round about 50 DB?

  The problem might be that in the manual of the PXI-5105 page 7 the SINAD of the device is between 50-62 db.

  If you want to get the best result, you must use a map better as the PXI-5122 page 9 the beach is here

  89 - 102 db.